Set-Up & First Brew; Priming Brewer; Brew First Cup - Keurig B60 Use And Care Manual

Set-Up & First Brew
IMPORTANT: You cannot use your Keurig
brewer until it has been primed for its first use
as set forth below.
NOTE: If Brewer has been exposed to tempera-
tures below freezing, allow Brewer at least two
hours to reach room temperature before prim-
ing. A frozen or extremely cold brewer will not
prime properly and can cause damage.
Priming your Brewer
1. Unwrap cord and plug the brewer into a
grounded outlet.
2. Place a cup or mug on the Drip Tray Plate.
3. Remove the Water Reservoir from Brewer by
first removing Lid from Reservoir, then lifting
Reservoir straight up and away from Brewer
(may be tight). Rinse with fresh water.
4. Fill Water Reservoir with fresh water so that
the water level is just below the top edge of
the reservoir.
5. Place Water Reservoir base into the left
side of the Brewer and be sure the
Water Reservoir Lock Tabs engage
with the Brewer. Replace Lid on Water
Reservoir.
6. Press the Power Button found directly
above the LCD Control Center. The blue light
surrounding the Travel Mug Button will
become illuminated and flash.
7. The LCD Control Center will come on and
indicate 'PRIME' and the button for the
6
Travel Mug will also flash. Please note, a K-
Cup should not be used for the Priming
Sequence.
Power Button
PRIME
Travel Mug
Button
8. Press the Travel Mug Button.
NOTE: If the Water Reservoir is empty or
not in place on the Brewer, then the LCD
Control Center will also indicate 'ADD
WATER'. None of the buttons will be activated
until water is added to the Water Reservoir.
9. The Brewer will automatically fill with water
(priming it) and then the water will be
heated. This will take about 3 minutes. During
the heating period 'NOT READY' is dis-
played on the LCD Control Center. Once the
water is heated, 'READY' will be displayed and
the Travel Mug button will flash.
NOTE: You may see small amounts of water
coming from the Vent and dripping into the
Water Reservoir during this and subsequent
heating – this is normal.
10.Press the Travel Mug Button to start a
cleansing brew, during which hot water will
flow into your cup or mug. Pour the hot
water into the sink.
11.The one-time priming process is now
complete and you are ready to brew!
NOTE: The Brewer may take 15 seconds to
reheat water between brews and then
'READY TO BREW' will be displayed.
Ready to Brew your First Cup
K-Cup ®
Handle
portion pack
K-Cup
Chamber
1. LCD Control Center will indicate 'READY TO
BREW'.
2. Place a cup or mug on the Drip Tray Plate.
3. Lift the Handle and the K-Cup Holder will
open toward you.
CAUTION: There are two sharp needles that
puncture the K-Cup ® portion pack, one above
the K-Cup Holder and the other in the bottom
of the K-Cup Holder. To avoid risk of injury,
do not put your fingers in the K-Cup Chamber.
4. Select a K-Cup ® portion pack.
NOTE: Do not remove the foil lid or
puncture the K-Cup ® portion pack.
5. Place a K-Cup ® portion pack in the K-Cup
Holder (as shown in exhibit at top of page).
6. Lower the Handle to close the Lid over the
K-Cup Holder. (When it is closed completely,
the LCD Control Center will indicate 'READY
TO BREW' and the Cup, Mug and Travel Mug
Buttons will blink up to 60 seconds.)
READY
TO BREW
Travel Mug
Button
MENU
Cup Button
Mug Button
7. Choose the amount of coffee or tea you
wish to brew by pressing the button that
indicates your choice. The Travel Mug choice
will yield a 9.25 oz serving, the Mug choice
will yield a 7.25 oz serving and the Cup
choice will yield a 5.25 oz serving.
NOTE: If you do not push the Brew Buttons
in 60 seconds, the LCD Control Center will
return to 'READY TO BREW' and the Brew
Buttons will be disabled to prevent accidental
activation. Re-activate the Brew Buttons by
raising and lowering the Handle completely.
8. The LCD Control Center will now display the
word 'BREWING' and the serving size you
selected will be solid blue.
BREWING
MENU
CAUTION: There is extremely hot water in
the K-Cup Holder during the brew process.
To avoid risk of injury, do not lift the
Handle or open the K-Cup Chamber
during the brew process.
9. There may be a short pause before the
brewing process begins. The process lasts
for approximately 40 seconds and ends
with a burst of air to remove all liquid
coffee or tea from the K-Cup.
10. Lift the Handle and remove and dispose of
the used K-Cup.
CAUTION: K-Cup will be hot.
11. Enjoy your first cup of Keurig Brewed ®
gourmet coffee or tea!
12. Your Brewer may display 'NOT READY' as
it heats water for the next brew cycle. The
'READY TO BREW' indication will return to
the LCD Control Center in about 15 seconds.
NOTE: Following the brew, your Brewer will
fill in preparation for the next brew. The pump
will make a vibrating sound. This is normal.
7