GE PEB2060SMSS Installation Instructions Manual
  1. Manuals
  2. Brands
  3. GE Manuals
  4. Kitchen Appliance Accessories
  5. PEB2060SMSS - Countertop Microwave Oven
  6. Installation instructions manual
GE PEB2060SMSS Installation Instructions Manual

GE PEB2060SMSS Installation Instructions Manual

Built-in trim kits
Hide thumbs Also See for PEB2060SMSS:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
Installation
Instructions
Questions? In the U.S., call 800.GE.CARES (800.432.2737)
In Canada, call 1.800.561.3344

BEFORE YOU BEGIN

❒
Read these instructions completely and carefully.
IMPORTANT –
•
IMPORTANT –
•
Note to Installer –
•
Consumer.
Note to Consumer –
•
• For easier installation and personal safety, we recommend that two people
install this microwave oven.
WARNING
grounded 3-hole, 120V receptacle as required by the National Electrical Code
or the Canadian Electrical Code.

FOR YOUR SAFETY:

WARNING –
installation, switch power off at service panel and lock
the service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.

TOOLS YOU WILL NEED

❒ Phillips screwdriver
❒ Pencil
❒ Awl or punch
❒ Level
READ CAREFULLY.
KEEP THESE INSTRUCTIONS
or Visit our Website at:
Save these instructions for local inspector's use.
Observe all governing codes and ordinances.
Be sure to leave these instructions with the
Keep these instructions for future reference.
—
This oven must be plugged into a properly
Before beginning the
❒ Drill with
7
⁄
" bit or #35
64
❒ Tape measure
❒ Scissors (optional)
.
Built-In Trim Kits
JX2027 and JX2030
or Visit our Website at:
GEAppliances.ca.
• Do not alter or modify any part of this kit or the oven.
• Unplug the microwave oven before attempting installation of this kit.
• Skill level – Installation of this appliance requires basic mechanical and
electrical skills.
• Completion time – 1-3 hours
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not covered under the Warranty.
• This kit is UL/CSA listed for installation alone or over any GE/GE Profile
single electric wall oven. Not for use adjacent to (within 2 feet of) any gas
or electric range, cooktop or oven.
• This kit is for use on models: PEB2060DMBB, PEB2060DMWW,
PEB2060DMCC, PEB2060SMSS, JEB1860DMBB, JEB1860DMWW,
JEB1860DMCC, JEB1860SMSS, PEB206CDNBB, PEB206CSNSS,
PEB206CDNWW, JEB186CDNWW, JEB186CDNBB and JEB186CSNSS.

PARTS INCLUDED

PART
NOTE: This kit has extra screws to prevent the technician from spending extra
time locating a replacement screw in case they lose one during installation.
1
ge.com.
QUANTITY
❒
Trim Frame
❒
Bottom Duct
❒
Side Duct
❒
4 mm x 12 mm
Round-Head Screws (21 required
for installation)
❒
4 mm x 14 mm
Flat-Head Screws
(4 required for
installation)
❒
Anti-Tip Brace
❒
Anti-Tip Bracket
❒
Upper Duct
❒
Top Bracket
❒
Bottom Bracket
❒
Templates
1
1
1
23
6
1
1
1
1
1
2

Advertisement

Table of Contents
loading

Related Manuals for GE PEB2060SMSS

Summary of Contents for GE PEB2060SMSS

  • Page 1: Installation Instructions

    • Product failure due to improper installation is not covered under the Warranty. • This kit is UL/CSA listed for installation alone or over any GE/GE Profile single electric wall oven. Not for use adjacent to (within 2 feet of) any gas or electric range, cooktop or oven.

  • Page 2: Cutout Dimensions

    ❒ CUTOUT DIMENSIONS Models 27″ Height ⁄ ″ Width ⁄ ″ Depth (min.)* ⁄ ″ or 22″ * Min. depth with receptacle outside cabinet 19 Min. depth with receptacle inside cabinet 22″ 120 volt-60 Hertz grounded power receptacle ⁄ ″ Overlap 27″...

  • Page 3: Install Microwave Oven

    ❒ INSTALL ANTI-TIP BRACKET AND BOTTOM DUCT Disconnect the microwave oven before proceeding with the installation. Fasten the anti-tip bracket to the bottom duct by using four round-head screws. Front Rear Round-Head Screws (4) Remove any loose items inside the microwave oven, including the turntable and turntable support.
  • Page 4 ❒ CHECK LEVELING Check the leveling by placing a level at the front and sides of the microwave. It may be necessary to add wood shims under the bottom duct to level the microwave front to back or side to side. ❒...
  • Page 5 Chine Imprimé fonction. disjoncteur place micro-ondes. à four dans usage pour référence d’installation instructions micro-ondes. à tournant plateau support Remettez installé. maintenant ARTICLES PLACE plate plate tête à bas). l’intérieur à (deux plate tête cadre Fixez micro-ondes. à position. s’enclenchent jusqu’à...
  • Page 6 avec centré micro-ondes à four antibasculement. renfort dans l’engageant position faites-le l’ouverture dans micro-ondes coupé. d’alimentation cordon assurant dans micro-ondes à four glisser soigneusement illustré. comme antibasculement dans correctement loge qu’il pour l’ouverture surface à parallèle être doit antibasculement micro-ondes. antibasculement Support ronde...
  • Page 7 ronde. tête à deux avec l’ouverture antibasculement support antibasculement support Renfort ronde tête support renfort l’installation l’illustration. montre comme poinçon avec antibasculement support renfort centrales positions Marquez centrale ligne avec gabarit centrale l’ouverture inférieure surface avec l’alignant gabarit Placez long gabarit, avant bord...

  • Page 8: D'installation Instructions

    perdait s’il remplacement chercher à temps éviter pour supplémentaires comprend ❒ Gabarits ❒ inférieur Support ❒ supérieur Support ❒ supérieur Conduit antibasculement ❒ Support antibasculement ❒ support Renfort l’installation) à nécessaires sont ❒ plate tête à l’installation) à nécessaires sont ❒...

This manual is also suitable for:

Jx2027Jx2030

Table of Contents