Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Intermec PB40A
Summary of Contents for Intermec PB40A
- Page 1 Quick Start Guide PB40A Bluetooth 4 inch Belt Printer...
-
Page 2: Packing List
Universal. AC Adapter, 12 volt DC Cigarette Lighter Adapter, 12 volt Supplies Replacement Li-Ion 7.2V 1.35 mAh Battery Thermal paper 130’/roll, 50/case Cleaning Card Part Number 226-469-002 Part Number 851-060-104 320-066-133 Part Number 320-081-122 320-081-011 320-066-013 PB40A Printer Quick Start Guide... -
Page 3: Getting Started
Getting Started Paper tear bar Battery packs Self-Test button IrDA window (side panel) Charge indicator DC power jack Paper release lever RJ-11 port Card reader Read LED PB40A Printer Quick Start Guide... -
Page 4: Charging The Lithium Ion Batteries
Or unplug from charging source, wait 15-20 seconds and reconnect. Indicates Printer has come out of sleep mode Printer is out of paper Battery is low No program in printer, only boot code PB40A Printer Quick Start Guide... -
Page 5: Paper Loading
Paper Loading Out of Paper The PB40A Printer sounds two quick beeps when it runs out of paper. If the printer is out of paper, the printer suspends opera- tion until paper is present and the lever is down. The printer continues to communicate with the mobile computer as long as it does not “time out.”... -
Page 6: Manual Paper Loading
6 Push down the paper release lever and insert the paper into the paper well with it resting in the paper rod clips. 7 Press the red button while the printer is on and it will feed paper. You will need about 2 inches of paper coming out of the mechanism. -
Page 7: Printer Self Test
“LOC” shows whether a font is Resident (R) or Downloaded (D). “CPI” shows characters per inch. “DESCRIPTION” describes the graphic. “NAMES” give the “Easy Print” name, the Line Printer name, and the hexadecimal equivalent of that name. PB40A Printer Quick Start Guide... -
Page 8: Battery Pack Removal
Remove the four screws securing the printer mechanism. Lift the printer mechanism out of the case. One way to do this is to turn the printer case on its side and gently tap the bottom of the case to remove the board assembly. Be... - Page 9 Printer assembly wire cluster Remove the four screws securing the battery cover. Avoid contact with the printer control board unless the board is grounded. Battery cover screws PB40A Printer Quick Start Guide Battery pack compartment Battery pack cable...
- Page 10 Replace the four screws to secure the battery pack cover to the printer mechanism. S Install the screws enough so they are fully seated but not any further or you will strip the screw holes in the printer case. Keyed battery pack connector...
- Page 11 Computer to Printer Jack Mobile Computer to Printer Cable 2 As you use the printer the power comes from the battery in the printer. When the printer battery runs down the printer will not operate until the battery is recharged.
- Page 12 1 Prepare the PB40A by holding down the red button for about two seconds until you hear a short beep. This means the printer is ready to go and will be discoverable. S Any time you press and hold the button until it beeps, you will dump any active wireless printing sessions.
- Page 13 The progress bars indicate the inquiry status. 6 A list of discovered devices displays. If your remote wireless printer is discovered and presented in the list, select the appropriate check box and click Next. If your remote device is not displayed, ensure that the device and its radio are switched ON.
-
Page 14: Maintenance And Troubleshooting
If the printer is out of paper (or the paper release lever is in the up position) this condition interrupts a batch of receipts, and the printer suspends operation until the condition is fixed. The printer continues to communicate with the mobile computer as long as it does not “time out.”... - Page 15 Paper Options button. Adjust the Dark- ness setting to a higher percentage until the print is dark and crisp. Refer to the Intermec Portable Printers Technical Reference Manual (p/n: 978-018-001) Section 4 for more details.
-
Page 16: Printer Specifications
RS-232C, Infrared, IrDA, ASK Full IBM and international character sets Easy Print Protocol for Bar Codes, Stored Graphics, Rotated Fonts. 900 mAh Li Ion 2 cell pack One year, includes print head. Ex- tended warranty available. PB40A Printer Quick Start Guide... -
Page 17: Global Services And Support
Web Support Visit our web site http://www.intermec.com to download many of our current manuals in PDF format, utilize our technical knowl- edge base ‘Knowledge Central’ or to request technical support. -
Page 18: Conditions Of Warranty
(1) year from date of shipment. This one year warranty applies to the PB40A Printer only. The warranty on the battery pack is 90 days from date of shipment. - Page 19 PB40A Printer Quick Start Guide...
- Page 20 Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com e 2003-2006 by Intermec Technologies Corporation. All rights reserved. PB40A Printer Quick Start Guide *962-018-025E* P/N 962-018-025E...