Revise/Delete Holiday Schedules And Dates; Programming Example - Intermatic ET70415CR User Manual

review. You must revise the data by reviewing the appropriate
individual day, day group, or "copied from" day.
• During automatic review, the OK key must be used to pause
the display before the displayed data can be deleted.
• After any program data is cleared, review is terminated. The
timer is now in the program mode for the selected day,
anticipating a new entry. You may make the new entry, restart
review, or return to RUN position.
• It is recommended that you repeat the "week long review" after
any revisions are complete to verify that all revisions were
implemented as desired.
To revise or delete displayed information during Program Review,
simply press CLEAR. You can then immediately make the revision
desired. Be sure to press OK to enter the new data. Press REV to
restart the review. Note that you can delete a Pulse or Interval
option from any Switch On or Switch Off time by pressing
CLEAR when the time is displayed during Review. You must re-
enter, then OK the Switch On or Switch Off time, even if it has
not changed. Likewise, you may add a Pulse or Interval to a
Switch On or Switch Off time by pressing CLEAR when the time
is displayed. You must re-enter the time, press PULSE or INTVL,
enter the length of Pulse or Interval, then press OK.
REVISE/DELETE HOLIDAY SCHEDULES AND
DATES
• To revise holiday Start/Stop dates: Press SET UP, then HLDY,
then the Holiday # (if known), then REV. The selected Holiday
# will show. Press REV again; the START date will show.
Pressing CLEAR will delete the START and STOP dates. Enter
the new START date, then OK. Enter the new STOP date, then
OK.
• To revise holiday schedules: Press PROG, then HLDY, then the
Holiday #. Press REV until the time that requires revision is
displayed. Press CLEAR to delete the displayed time. Enter and
OK a new time if desired.
16
• To delete a holiday# (and thus its Start/Stop dates) that has
never had any scheduled On/Off times: Press SET UP, then
HLDY, then the Holiday #, then REV, then CLEAR. If the
display shows "__", the Holiday has been deleted. If "ERR 22"
shows, this Holiday has, or once had, a schedule. If so, press any
key to clear the error message then follow the steps below.
• To delete a holiday# (and thus its Start/Stop dates) when the
holiday has or once had scheduled On/Off times: Enable any
circuit, press PROG, then HLDY, then the Holiday #, then
REV. The selected Holiday # will show. Press CLEAR; the timer
will scroll a message asking if you are sure you want to delete the
Holiday schedule. After the message stops and the Holiday # is
re-displayed, press CLEAR to delete it. Now press SET UP, then
HLDY, then the Holiday #, then REV, then CLEAR. The
holiday is now completely deleted.
PROGRAMMING EXAMPLE (2 circuits only)
Be sure RUN/SET is in SET position. At the initial installation
and/or to clear out all previously programmed data, press and hold
the CLEAR button, then press and release RESET and continue to
hold the CLEAR button until RESET appears in the display. Note
leading zeros are not required for the left-most prompted digit.
Press SET UP (unless prompt is flashing at Day of Wk/Time)
Assume • Current day and time is Tuesday, 2:30 P.M.
• Current date is January 21, 1997
• Location is Des Moines, Iowa (Zone 5 from Astro
Zone Map and center of Central time zone)
• The building owner wants the lights Off 30 min.
after sunrise and On 30 min. prior to sunset.
• Two Holiday or special schedules – July 4th and a
2-week office closing 12/22/97 thru 1/5/98
Press TUE/3, OK (selects day); 2, 3, 0, PM, OK (selects time);
1, 2, 1, 9, 7, OK (selects date); 5, OK (selects zone).
The time switch now displays the calculated center of
time zone sunrise time of -7:33 A.M. Since the building
Next Generation
17