Table of Contents
Advertisement
Station Selection
1. Press the
button
AM/FM
select the tuner as an input.
2. Press the
button
AM/FM
to switch between AM and FM so that the
desired frequency band is selected.
3. Press the
button
Tune Mode
to select manual or automatic tuning.
When the
indicator
Q
AUTO
ated in the Main Information Display the
tuner will only stop at those stations that
have a strong enough signal to be
received with acceptable quality.
When the
indicator
S
MONO
ated, the tuner is in a manual mode and
will stop at each frequency increment in
the selected band.
4. To select stations press the
button
% t
. When the
AUTO
is illuminated each press will cause
Q
the tuner to search for the next highest
or lowest frequency station that has an
acceptable signal. When tuning FM sta-
tions in the Auto mode, the tuner will
only select Stereo stations. To tune to the
next station, press the button again. If
the
indicator
is illuminated,
S
MONO
tap the
button
% t
Tuning
advance one frequency increment at a
time, or press and hold it to locate a spe-
cific station. When the
TUNED
illuminates, the station is properly
T
tuned and should be heard with clarity.
5. Stations may also be tuned directly
by pressing the
button
Direct
then pressing the
Numeric Keys l
that correspond to the station's frequency.
The desired station will automatically
be tuned.
AVR65 120 volt Rev (C) 10/6/98
Operation
NOTE: When the FM reception of a
$ k
to
station is weak, audio quality will be
increased by switching to Mono mode
by pressing the
$ k
again
q
until the
goes out.
Preset Tuning
* q
Up to 30 stations may be stored in the
AVR65's memory for easy recall using the
front panel controls or the remote.
is illumin-
To enter a station to the memory, first
tune the station using the steps outlined
above. Then:
1. Press the
Memory
the remote. Note that
is illumin-
will illuminate and flash in the
P
Information Display.
2. Within five seconds, press the
Numeric Keys l
Tuning
the location where you wish to store this
indicator
station's frequency.
3. Repeat the process after tuning any
additional stations to be preset.
Recalling Preset Stations
• To manually select a station previously
entered in the preset memory, press the
Numeric Keys l
to
the desired station's memory location.
• To manually tune through the list of
indicator
stored preset stations one by one, press
the
buttons
Preset
panel or remote.
m
, and
29
button
*
Tune Mode
indicator
R
STEREO
button
n
on
indicator
MEMORY
corresponding to
that correspond to
& s
on the front
• To automatically scan through the sta-
tions entered in the preset memory, press
the
button
^
on the front
Preset Scan
panel. The tuner will run through the list
of preset stations, stopping for five seconds
at each one. Press the button again to stop
the scan at your desired station.
Tape Recording
In normal operation, the audio or video
source selected for listening through the
AVR65 is sent to the record outputs.
This means that any program you are
watching or listening to may be recorded
simply by placing machines connected
to the outputs for
Tape Monitor f
in the record mode.
Video 1 ¢
When a tape recorder with separate record
and playback heads is used, you may
monitor the output of the recording by
selecting the
Mon Selector 9 k
T
•
Note that a red LED will illuminate in the
Mon Selector 9
front panel above the
T
•
to remind you that you are listening to the
record playback instead of the actual input
source being recorded.
NOTE: It is not possible to record the
output of digital sources.
IMPORTANT NOTE: Please make cer-
tain that you are aware of the copyright
restrictions on any material you copy.
Unauthorized duplication of copyrighted
materials is prohibited by Federal law.
or
.
Hide quick links:
Advertisement
Table of Contents
