Sign in today to find solutions:

Forgot your password?

Don't have an account? Sign up

 
+ 3
' H V L J Q - H W     6 H U L H V
7 D N H  8 S 5 H H O
User's Guide

Summary of Contents

  • Page 1

    ' H V L J Q - H W     6 H U L H V 7 D N H  8 S 5 H H O User’s Guide...

  • Page 2

    The Hewlett-Packard Company shall not be liable for incidental or consequential damages in connection with, or arising out of the furnishing. performance. or use of this document and the program material which it describes. HP DesignJet 1000 Series Take-Up Reel...

  • Page 3: Table Of Contents

    Drying Time with the Take-Up Reel 36 Troubleshooting 38 Take-Up Reel Specifications 39 Regulatory Notices 41 Declaration of Conformity 43 Checking the Firmware Revision Number 4 Take-Up Reel Does Not Function 38 Paper Skewed on Take-Up Reel 38 HP DesignJet 1000 Series Take-Up Reel...

  • Page 4: Upgrading Your Printer, Checking The Firmware Revision Number

    If your firmware revision number is A.01.04 or A.01.04A, you need to contact an HP Customer Care Centre, which will send you a free Firmware Upgrade Kit. The telephone numbers of HP Customer Care Centres in each country are listed in the Customer Care booklet provided with your take-up reel.

  • Page 5: Installing A New Firmware Module

    1 If the printer is turned on, turn it off at the front panel. 2 Looking at the rear of the printer, remove the paper path deflector from the left rear side of the printer. To do this, push the two slots in the deflector downwards and then pull it towards you.

  • Page 6

    3 Switch the printer off at the power isolator switch at the back of the printer and disconnect the power cord and the interface cable. 4 Unscrew the four screws and remove the cover plate at the back of the printer.

  • Page 7

    5 Looking at the back of the printer, you will see three slots. It is important to install the firmware module in the slot that is furthest to the right. 6 Put on a grounding wrist strap and attach the other end to the metal chassis of the printer.

  • Page 8

    9 Carefully push the top edge of the firmware module into the slot. 10 Continue pushing the top edge of the firmware module until you feel it “click” into position. At the same time you will see that the top locking tab locks into position. HP DesignJet 1000 Series Take-Up Reel...

  • Page 9

    “click” into position. Again, you will see that the bottom locking tab locks into position. 12 Remove the grounding wrist strap and then re-install the cover plate on the back of the printer, using the four screws. HP DesignJet 1000 Series Take-Up Reel...

  • Page 10

    13 Re-install the paper path deflector on the left side of the printer. 14 Reconnect the power cord and the interface cable and switch on the power isolator switch at the back of the printer. You have now finished installing the firmware module.

  • Page 11: Take-up Reel Components

    These are the main components of the take-up reel. Left-hand assembly Take-up reel spindle 3-inch core adaptors Paper guide Documentation, assembly tool, etc. Deflector supports Take-up core (different lengths) Take-up reel Right-hand sensor assembly Paper weight (different lengths) Deflector rod HP DesignJet 1000 Series Take-Up Reel...

  • Page 12

    The following picture shows the main components of the take-up reel and where they are installed on the printer, Left-hand assembly HP DesignJet 1000 Series Take-Up Reel Deflector Right-hand assembly Take-up reel sensor...

  • Page 13: Installing The Take-up Reel

    Carefully lever apart the capping strip assembly through the holes at the bottom. Carefully lever the six retaining clips from the paper-bin support. Carefully lever the six retaining clips from the cross-brace assembly. HP DesignJet 1000 Series Take-Up Reel...

  • Page 14

    Do not tighten them yet. Install 4 screws HP DesignJet 1000 Series Take-Up Reel Release the clamp on the left-hand assembly by loosening the screw shown below. Do not remove the screw.

  • Page 15

    Close the clamp and secure with the clamp screw as shown below. Tighten the two screws supporting the assembly. Release the clamp on the right-hand assembly. by loosening the screw shown below. Do not remove the screw. HP DesignJet 1000 Series Take-Up Reel...

  • Page 16

    10. Pull the right-hand assembly down so that it rests securely on the screws. HP DesignJet 1000 Series Take-Up Reel Close the clamp and secure with the clamp screw as shown below.

  • Page 17

    Tighten the screw to secure the clamp in place and connect the sensor cable as shown below. Ensure this is clipped under the foot HP DesignJet 1000 Series Take-Up Reel...

  • Page 18

    Then put the paper guide back on to the spindle and lock it with the blue lever.. HP DesignJet 1000 Series Take-Up Reel Ensure the spindle lock is open. Install the take-up reel spindle into the printer by pushing firmly on each end of the spindle A then B as shown below.

  • Page 19

    T-piece on top of the support is fully inserted into the gap between the cross brace and the printer leg. The deflector support should now be touching the take-up reel assembly. Rest the deflector rod on the two supports. HP DesignJet 1000 Series Take-Up Reel...

  • Page 20

    If you have disconnected the printer’s power cord, re-connect it now, turn on the power isolator switch at the back of the printer, then turn on the printer using the on/off button on the front panel. Wait until the printer has finished initializing and a “Ready”...

  • Page 21: Loading Paper On To The Take-up Reel

    Before using the take-up reel, ensure that it has been properly installed (see preceding pages). In particular, the core tube should be mounted on the spindle. CAUTION HP Bright White Inkjet Paper is available in 150-ft and 300-ft rolls. The take- up reel can only completely roll up 150-ft rolls. CAUTION Backlit paper with a separate slip sheet is not recommended for use with the take-up reel.

  • Page 22

    2 Ensure that the spindle lock is closed. 3 Move the adjustment levers on the left and right paper guides to the unlocked position. HP DesignJet 1000 Series Take-Up Reel...

  • Page 23

    The paper guides may be slightly stiff on the spindle: you may have to use both hands. 5 When you have adjusted the position of the core, pull the adjustment levers on both paper guides to the locked position. HP DesignJet 1000 Series Take-Up Reel...

  • Page 24

    6 Pull the paper taut to the position shown below. Do not attempt to pull more paper out of the printer; if you need more paper, use the front panel. HP DesignJet 1000 Series Take-Up Reel...

  • Page 25

    8 Press the key on the front panel to advance the paper. Enough paper should be advanced so that the paper can wrap at least once around the core. Advance about this much paper HP DesignJet 1000 Series Take-Up Reel...

  • Page 26

    It is important that the paper weight is the same width as the paper you are using. By matching color coded lengths of plastic tube, you can make a paper weight for different widths of standard paper sizes: 24”, 36”. HP DesignJet 1000 Series Take-Up Reel...

  • Page 27

    It is important that the paper weight is inserted. The take-up reel will not function properly without it. 12 Press Enter on the printer’s front panel, which will then display the Ready message. NOTE: When the take-up reel is in operation it is important to ensure that the take- up reel sensor is not blocked.

  • Page 28

    13 Shown below is how the printer should look when it is in operation. As paper is fed from the printer it drops down in a loop and up into the take-up reel spindle. HP DesignJet 1000 Series Take-Up Reel...

  • Page 29: Unloading Paper From The Take-up Reel

    The front panel will prompt you to remove the paper weight and wind excess paper using the take-up reel buttons. 3 Important: Remove the paper weight as shown below. It may help you to remove the end-caps first. HP DesignJet 1000 Series Take-Up Reel...

  • Page 30

    4 Press the paper wind button shown below to wind the paper hanging down onto the take-up reel. 5 Press Enter on the printer’s front panel. The printer will now cut the paper. 6 Slide open the spindle lock on the right-hand side of the take-up reel.

  • Page 31

    8 Unlock and remove the left-hand paper guide from the take-up reel spindle. Remove the core from the spindle. Take-up reel spindle Paper guide To remove roll paper from the printer, see the User’s Guide. Take-Up Core (with paper) HP DesignJet 1000 Series Take-Up Reel...

  • Page 32: Changing The Core Tube On The Take-up Reel

    To change the core, perform the following procedure. 1 Slide open the spindle lock on the right hand side of the take-up reel. 2 Remove the take-up reel spindle from the printer as shown by pulling firmly on each end of the spindle, A then B.

  • Page 33

    24”, 36”. Alternatively, you can use an empty paper cardboard core. NOTE: Ensure the take-up core is pushed firmly into both paper guides. HP DesignJet 1000 Series Take-Up Reel...

  • Page 34

    NOTE: If you want to use a three-inch cardboard core, use the three-inch core adaptors shown below. 3-inch core adaptors Left-hand paper guide HP DesignJet 1000 Series Take-Up Reel Take-up reel spindle Take-up core Right-hand paper guide...

  • Page 35

    6 Install the take-up reel spindle into the printer by pushing firmly on each end of the spindle, A then B. 7 Slide shut the spindle lock on the right-hand side of the take-up reel. HP DesignJet 1000 Series Take-Up Reel...

  • Page 36: Drying Time With The Take-up Reel

    However, sometimes the print will need a longer time to dry, and so the printer will slow down the printing process to allow more time before winding on to the take-up reel; this is called the drying time.

  • Page 37

    In this mode you can override the amount of time that the printer has estimated to print your image. However, the printer needs a certain minimum amount of time to print. If the amount of time that you have specified is less than this, the printer will ignore your setting.

  • Page 38: Troubleshooting, Take-up Reel Does Not Function, Paper Skewed On Take-up Reel

    Perhaps the paper weight is not fully inserted. Perhaps the take-up reel spindle is not installed correctly. Perhaps the left- and right-hand take-up reel assemblies are not installed correctly. Ensure that there are no objects in the base tray assembly. HP DesignJet 1000 Series Take-Up Reel...

  • Page 39: Take-up Reel Specifications

    Operating Relative Humidity: Storage ranges 95% humidity Printhead and Printhead Cleaners stored in the HP DesignJet Ink System Storage Container: Temperature: +15 C to +35 C (+59 F to +95 F) @ 20% - 80% Relative Humidity 15 C to 30 C (59 F to 86 F)

  • Page 40

    Canadian Standards Association “Certified” ITE, CSA C22.2 No.950 European Union 73/23/EEC Low Voltage Directive compliant. Meets EN 60950 Germany TUV EN60950 certified Mexico DGN, NOM019-SCFI-1994 certified Underwriters' Laboratories UL 1950 Listed Poland PCBC certified Russia GOST certified HP DesignJet 1000 Series Take-Up Reel...

  • Page 41: Regulatory Notices

    Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help C6079X (where X denotes any alphabetic character) HP DesignJet 1000 Series Take-Up Reel...

  • Page 42

    Radio Interference Regulations of the Canadian (Canada) Department of Communications. Taiwanese EMI statement Address Hewlett-Packard Company Manager of Corporate Product Regulations 3000 Hanover Street Palo Alto, CA 94304 415/857-1501 HP DesignJet 1000 Series Take-Up Reel...

  • Page 43: Declaration Of Conformity

    The product herewith complies with the requirements of the Low-Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC and carries the CE marking accordingly. The product was tested in a typical system with a Hewlett-Packard DesignJet series printer. Sant Cugat del Valles (Barcelona),...

  • Page 44

    © Copyright Hewlett-Packard Company 1999 Part number: C6079-90001 First edition Printed in Europe Hewlett-Packard Company Barcelona Division Avda. Graells, 501 08190 Sant Cugat del Vallès Barcelona, Spain...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: