HP EliteBook 6930p Maintenance And Service Manual

HP EliteBook 6930p Maintenance And Service Manual

Notebook pc
Hide thumbs Also See for EliteBook 6930p:
Table of Contents

Advertisement

HP EliteBook 6930p Notebook PC
Maintenance and Service Guide

Advertisement

Table of Contents
loading

Summary of Contents for HP EliteBook 6930p

  • Page 1 HP EliteBook 6930p Notebook PC Maintenance and Service Guide...
  • Page 2 The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
  • Page 3 Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
  • Page 4 Safety warning notice...
  • Page 5: Table Of Contents

    Table of contents 1 Product description 2 External component identification Top components ... 8 Display ... 8 Antennae ... 9 Button, switches, and fingerprint reader ... 10 Keys ... 11 Lights ... 12 Pointing devices ... 13 Front components ... 14 Rear components ...
  • Page 6 Unknown user password ... 40 Component replacement procedures ... 41 Service tag ... 41 Computer feet ... 42 Battery ... 43 SIM ... 44 Display inverter ... 45 Bluetooth module ... 47 Hard drive ... 49 Optical drive ... 51 Upgrade bay device ...
  • Page 7 File menu ... 97 Security menu ... 97 Diagnostics menu ... 98 System Configuration menu ... 99 6 Specifications Computer specifications ... 101 14.1-inch, WXGA display specifications ... 102 Hard drive specifications ... 103 DVD±RW and CD-RW Double-Layer Combo Drive specifications ... 104 DVD/CD-RW Combo Drive specifications ...
  • Page 8 Recovering the entire hard drive using f11 ... 137 Recovering information using a Windows Vista operating system DVD (purchased separately) ... 138 9 Backup and recovery in Windows XP Backing up your information ... 139 When to back up ... 139 Backup suggestions ...
  • Page 9: Product Description

    Product description Category Description Product Name HP EliteBook 6930p Notebook PC Processors Intel® Core™ 2 Duo processors ● ● ● ● Chipset Northbridge: Intel GM45 with up to 1067 FSB with iAMT support Northbridge: Intel PM45 with up to 1067...
  • Page 10 Category Description ● ● Memory 2 customer-accessible/upgradable memory module slots Supports dual-channel memory Supports up to 8 GB of system RAM PC2-6400, 800-MHz, DDR2 Supports the following configurations in all countries and regions except Brazil: ● ● ● ● ● ●...
  • Page 11 Category Description Serial ATA Supports Disk Sanitizer Supports full disk encryption Supports HP 3D DriveGuard Supports RAID 0 (striping) and RAID 1 (mirror) Supports the following drives: ● 250-GB, 5400-rpm hard drive ● 160-GB, 7200-rpm hard drive ● 160-GB, 5400-rpm hard drive ●...
  • Page 12 Category Description Modem 56K V.92 1.5-inch data/fax modem Support for no-modem option Ethernet Intel 82567LM 10/100/1000 Ethernet, with iAMT Intel 82567LM Gigabit network connection S4/S5 wake on LAN: DC - no S4/S5 wake on LAN: AC - yes Wireless Integrated WLAN options by way of wireless module: 3 WLAN antennae built into display assembly Support for no-WLAN option...
  • Page 13 Dualpoint (pointing stick and TouchPad) with 2 pointing stick buttons and 2 TouchPad buttons Power 90-W HP Smart AC Adapter with requirements localized cable plug support (2-wire plug with ground pin, supports 2- pin DC connector) 6-cell, 55-Wh Li-ion battery...
  • Page 14 Category Description Windows® Vista® Basic 32 with and without Office Ready Windows Vista Business 32 with and without Office Ready Windows Vista Ultimate with Office Ready (in Canada and the United States) Windows Vista Business with Windows® XP Pro with and without Office Ready Windows Vista Basic 32 with Office Personal and Powerpoint (Japan)
  • Page 15 Category Description SuSE Linux Web support: Windows Vista Enterprise 32 Windows Vista Enterprise 64 Windows XP Pro Serviceability Customer service replaceable (CSR) parts: AC adapter Battery (system) Expansion memory module Hard drive Keyboard Optical drive Primary memory module WLAN module WWAN module Computer models Computer models equipped...
  • Page 16: External Component Identification

    Top components Display Item Component Ambient light sensor Internal microphones (2) HP Webcam HP Webcam light Keyboard light Keyboard light button Chapter 2 External component identification Function Automatically adjusts the display brightness based on the lighting conditions in your environment.
  • Page 17: Antennae

    Antennae Item Component WWAN antennae (2)* WLAN antennae (3)* *The antennae are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennae free from obstructions. Description Send and receive wireless signals to communicate with wireless wide-area networks (WWAN).
  • Page 18: Button, Switches, And Fingerprint Reader

    Button, switches, and fingerprint reader Item Component Power button Internal display switch Info button Wireless button Presentation button Volume mute button Chapter 2 External component identification Function ● When the computer is off, press the button to turn on the computer.
  • Page 19: Keys

    Item Component Volume scroll zone Fingerprint reader (select models only) Keys Item Component Windows logo key Windows applications key Embedded numeric keypad keys Function keys Function Adjusts speaker volume. Slide your finger to the left to decrease volume and to the right to increase volume. You can also press the left side of the volume slider to decrease volume, or press the right side of the volume slider to increase volume.
  • Page 20: Lights

    Chapter 2 External component identification Function ● On: An integrated wireless device, such as a wireless local area network (WLAN) device, the HP Broadband Wireless Module, and/or a Bluetooth® device, is on. ● Amber: All wireless devices are off. ●...
  • Page 21: Pointing Devices

    Item Component Num lock light Volume mute light Volume down light Volume up light *The 2 wireless lights display the same information. The light on the wireless button is visible only when the computer is open. The wireless light on the front of the computer is visible whether the computer is open or closed. †The 2 power lights display the same information.
  • Page 22: Front Components

    Bluetooth compartment Chapter 2 External component identification Function On: An integrated wireless device, such as a wireless local area network (WLAN) device, the HP Broadband Wireless Module, and/ or a Bluetooth device, is on. Amber: All wireless devices are off. ●...
  • Page 23: Rear Components

    Rear components Item Component Security cable slot Power connector External monitor port Right-side components Item Component Smart card reader Upgrade bay USB port RJ-45 (network) jack RJ-11 (modem) jack Description Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen.
  • Page 24: Left-Side Components

    Left-side components Item Component Vent USB ports (2) 1394 port Audio-in (microphone) jack Audio-out (headphone) jack ExpressCard slot Chapter 2 External component identification Function Enables airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
  • Page 25: Bottom Components

    Bottom components Item Component Battery bay Docking connector Vents (5) Accessory battery connector Memory module compartment Hard drive bay WWAN module compartment Battery release latch SIM slot (select models only) Function Holds the battery. Connects an optional docking device. Enable airflow to cool internal components. CAUTION: To prevent overheating, do not obstruct vents.
  • Page 26: Illustrated Parts Catalog

    Illustrated parts catalog Serial number location The service tag, affixed to the bottom of the computer, provides information that may be needed when troubleshooting system problems. The service tag provides the following information: (1) Product name: This is the product name affixed to the front of the computer. (2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.
  • Page 27: Computer Major Components

    Computer major components Computer major components...
  • Page 28 Item Description 14.1-inch, AntiGlare display assemblies (include three WLAN antenna cables, two WWAN antenna cables, and two microphones): WXGA LED display assembly with webcam (includes webcam cable) WXGA LED display assembly without webcam WXGA+ display assembly with webcam (includes webcam cable) WXGA+ display assembly without webcam WXGA display assembly with webcam (includes webcam cable) WXGA display assembly without webcam...
  • Page 29 Item Description For use in Latin America For use in the Netherlands For use in Norway For use in Portugal For use in Russia For use in Saudi Arabia For use in Sweden and Finland For use in Slovakia For use in South Korea For use in Spain For use in Switzerland For use in Taiwan...
  • Page 30 Item Description P8400 2.26-GHz (1066-MHz FSB, 3-MB L2 cache) (10) Primary memory modules (PC2-6400, 667-MHz, DDR2) 4096-MB 2048-MB 1024-MB (11) Modem modules NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable is included in the Cable Kit, spare part number 487432-001.
  • Page 31 Item Description Broadcom BCM4312 802.11b/g WLAN modules: ● For use in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States ● For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands,...
  • Page 32 The Bluetooth module cable is included in the Cable Kit, spare part number 487432-001. See (26) HP un2400 Mobile Broadband WWAN module Chapter 3 Illustrated parts catalog Cable Kit on page 26 for more Cable Kit spare part information.
  • Page 33: Plastics Kit

    Plastics Kit Item Description Plastics Kit: Hard drive bay cover (includes 2 captive screws, secured by C-clips) Memory module compartment cover (includes one captive screw, secured by a C-clip) ExpressCard slot bezel WWAN module compartment cover (includes one captive screw, secured by a C-clip) Bluetooth module compartment cover (includes one captive screw, secured by a C-clip) Spare part number 487429-001...
  • Page 34: Cable Kit

    Cable Kit Item Description Cable Kit: Modem module cable (includes RJ-11 connector) Bluetooth module cable Chapter 3 Illustrated parts catalog Spare part number 487432-001...
  • Page 35: Mass Storage Devices

    Mass storage devices Item Description Hard drives (include bracket) 250-GB, 5400-rpm 160-GB, 7200-rpm 160-GB, 5400-rpm 120-GB, 7200-rpm 120-GB, 5400-rpm Optical drives (include bezel and bracket) DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe DVD/CD-RW Combo Drive DVD-ROM Drive Upgrade bay device cradle 80-GB solid-state drive Spare part number 483187-001...
  • Page 36: Miscellaneous Parts

    Miscellaneous parts Description AC adapters 90-W HP Smart AC adapter for use in all countries and regions except India 90-W HP Smart AC adapter for use only in India Power cords: For use in Argentina For use in Australia For use in Brazil...
  • Page 37: Sequential Part Number Listing

    Cable Kit, spare part number 487432-001. See Cable Kit spare part information. 463955-001 90-W HP Smart AC adapter for use in all countries and regions except India 463956-001 90-W HP Smart AC adapter for use only in India 480985-001 Intel Wi-Fi Link 5100 802.11a/b/g/n WLAN module for use in all countries and regions...
  • Page 38 Spare part Description number 482964-001 Power button board (includes cable) 482966-001 Display Cable Kit (includes display panel cable) 482967-001 Display Hinge Kit (includes left and right hinges) 482968-001 Rubber Kit (includes base enclosure rubber feet, rubber screw covers, and display bezel rubber screw covers) 482969-001 Wireless Antenna Kit (includes 3 WLAN antenna transceivers and cables and 2 WWAN antenna...
  • Page 39 Spare part Description number 483010-281 Keyboard for use in Thailand (includes keyboard cable, keyboard shield, pointing stick, and pointing stick cable) 483010-291 Keyboard for use in Japan (includes keyboard cable, keyboard shield, pointing stick, and pointing stick cable) 483010-A41 Keyboard for use in Belgium (includes keyboard cable, keyboard shield, pointing stick, and pointing stick cable) 483010-AB1 Keyboard for use in Taiwan (includes keyboard cable, keyboard shield, pointing stick, and pointing stick...
  • Page 40 14.1-inch, WXGA AntiGlare LED display assembly for use on computer models not equipped with a webcam (includes three WLAN antenna cables, two WWAN antenna cables, and two microphones) 483377-001 HP un2400 Mobile Broadband WWAN module 486299-001 System board with 128 MB of discrete graphics subsystem memory (includes replacement...
  • Page 41 Spare part Description number Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova,...
  • Page 42 Spare part Description number 500325-001 Logo Kit 502322-0001 Upgrade bay device cradle Chapter 3 Illustrated parts catalog...
  • Page 43: Removal And Replacement Procedures

    Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers ● Torx T8 screwdriver Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.
  • Page 44: Cables And Connectors

    Cables and connectors CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion.
  • Page 45: Grounding Guidelines

    Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry.
  • Page 46: Packaging And Transporting Guidelines

    Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
  • Page 47: Equipment Guidelines

    Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times.
  • Page 48: Unknown User Password

    Unknown user password If the computer you are servicing has an unknown user password, follow these steps to clear the password: NOTE: These steps also clear CMOS. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
  • Page 49: Component Replacement Procedures

    Component replacement procedures This chapter provides removal and replacement procedures. There are as many as 72 screws, in 12 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement.
  • Page 50: Computer Feet

    Computer feet The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare part number 482968-001. There are 4 rubber feet that attach to the base enclosure in the locations illustrated below. Chapter 4 Removal and replacement procedures...
  • Page 51: Battery

    Battery Description 6-cell, 55-Wh Li-ion battery 4-cell, 37-Wh Li-ion battery Before disassembling the computer, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 52: Sim

    NOTE: This section applies only to computer models with WWAN capability. If there is a SIM inserted in the SIM slot, it should be removed before disassembling the computer. Be sure the SIM is reinserted in the SIM slot after reassembling the computer. Before removing the SIM, follow these steps: Shut down the computer.
  • Page 53: Display Inverter

    Display inverter Description Display inverter Before removing the display inverter, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 54 Release the bottom edge of the display bezel (3) from the display assembly. Release the zero insertion force (ZIF) connector (1) to which the keyboard light cable is attached, and disconnect the keyboard light cable from the display inverter. Remove the two Phillips PM2.5×4.0 screws (2) that secure the display inverter to the display enclosure.
  • Page 55: Bluetooth Module

    Bluetooth module NOTE: The Bluetooth® module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare part number 487432-001. See module cable on page 87 Description Bluetooth module Before removing the Bluetooth module, follow these steps: Shut down the computer.
  • Page 56 Disconnect the Bluetooth module cable (2) from the Bluetooth module. Remove the Bluetooth module. Reverse this procedure to install the Bluetooth module. Chapter 4 Removal and replacement procedures...
  • Page 57: Hard Drive

    Hard drive NOTE: All hard drive spare part kits include a hard drive bracket. Description 250-GB, 5400-rpm 160-GB, 7200-rpm 160-GB, 5400-rpm 120-GB, 7200-rpm 120-GB, 5400-rpm Before removing the hard drive, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
  • Page 58 Grasp the Mylar tab (2) on the hard drive and slide the hard drive (3) to the right to disconnect it from the system board. Remove the hard drive (4) from the hard drive bay. If it is necessary to replace the hard drive bracket, remove the two Phillips PM3.0×4.0 hard drive bracket screws (1) from each side of the hard drive.
  • Page 59: Optical Drive

    Optical drive NOTE: All optical drive spare part kits include an optical drive bezel. Description DVD±RW and CD-RW SuperMulti Double-Layer Combo Drive with LightScribe DVD/CD-RW Combo Drive DVD-ROM Drive Before removing the optical drive, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
  • Page 60: Upgrade Bay Device

    Remove the optical drive bracket (2). Reverse this procedure to reassemble and install an optical drive. Upgrade bay device Description Upgrade bay device cradle Before removing the upgrade bay device, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
  • Page 61 Remove the upgrade bay device (4) from the computer. If it is necessary to remove the hard drive from the upgrade bay cradle, position the upgrade bay cradle with the front bezel toward you. Loosen the Phillips PM2.5×10.0 captive screw (1) that secures the hard drive to the upgrade bay cradle.
  • Page 62: Expansion Memory Module

    Expansion memory module Description 4096-MB memory module (PC2-6400, 667-MHz, DDR2) 2048-MB memory module (PC2-6400, 667-MHz, DDR2) 1024-MB memory module (PC2-6400, 667-MHz, DDR2) Before removing the expansion memory module, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
  • Page 63: Wwan Module

    Reverse this procedure to install the expansion memory module. WWAN module Description HP un2400 Mobile Broadband WWAN module Before removing the WWAN module, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
  • Page 64 Lift the left side of the cover (2), swing it up and to the right, and remove the cover. The WWAN module compartment cover is included in the Plastics Kit, spare part 487429-001. Disconnect the WWAN antenna cables (1) from the terminals on the WWAN module. NOTE: The red WWAN antenna cable is connected to the WWAN module “Main”...
  • Page 65: Keyboard

    Keyboard NOTE: All keyboard spare part kits include a keyboard cable, keyboard shield, pointing stick, and pointing stick cable. Country or region Belgium Brazil The Czech Republic Denmark France French Canada Germany Greece Hungary Iceland Israel Italy Japan Latin America The Netherlands Pointing stick rubber caps Before removing the keyboard, follow these steps:...
  • Page 66 Loosen the three Phillips PM2.5×9.0 captive screws that secure the keyboard to the computer. Turn the computer display-side up, with the front toward you. Open the computer as far as possible. Slide the four keyboard retention tabs (1) toward you. The tabs are located between the keys, between the keys.
  • Page 67: Primary Memory Module

    Release the ZIF connector (3) to which the keyboard cable is attached, and disconnect the keyboard cable (4) from the system board. Remove the keyboard. Reverse this procedure to install the keyboard. Primary memory module Description 4096-MB memory module (PC2-6400, 667-MHz, DDR2) 2048-MB memory module (PC2-6400, 667-MHz, DDR2) 1024-MB memory module (PC2-6400, 667-MHz, DDR2) Before removing the primary memory module, follow these steps:...
  • Page 68 Remove the memory module (2) by pulling the module away from the slot at an angle. NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the memory module slot. Reverse this procedure to install the primary memory module. Chapter 4 Removal and replacement procedures...
  • Page 69: Modem Module

    Modem module NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable is included in the Cable Kit, spare part number 487432-001. Description For use in all countries and regions except Australia and New Zealand Modem module for use only in Australia and New Zealand Before removing the modem module, follow these steps: Shut down the computer.
  • Page 70: Wlan Module

    WLAN module Description Intel Wi-Fi Link 5300 802.11a/b/g/n WLAN module for use in all countries and regions Intel Wi-Fi Link 5100 802.11a/b/g/n WLAN module for use in all countries and regions Intel Wi-Fi Link 5100 802.11a/b/g WLAN module for use in all countries and regions Broadcom 4322 802.11a/b/g/n WLAN modules: ●...
  • Page 71 Description Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe Before removing the WLAN module, follow these steps:...
  • Page 72 Reverse this procedure to install the WLAN module. Chapter 4 Removal and replacement procedures...
  • Page 73: Rtc Battery

    RTC battery NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords and CMOS settings to be cleared. Description RTC battery Before removing the RTC battery, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
  • Page 74: Switch Cover

    Switch cover Description Switch cover (includes capacitative board and cable) Before removing the switch cover, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 75 Lift the right side of the keyboard shield (1) until it rests at an angle, and then remove the shield (2) by lifting it straight up. NOTE: The keyboard shield is included with the keyboard spare part kit. Release the ZIF connector (1) to which the power button board cable is attached, and disconnect the power button board cable from the system board.
  • Page 76: Power Button Board

    Power button board Description Power button board (includes cable) Before removing the power button board, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 77: Fan

    Description Before removing the fan, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer.
  • Page 78: Heat Sink

    configurations, battery fast charging, and software requirements. Exhaust air is displaced through the ventilation grill located on the left side of the computer. Heat sink NOTE: The heat sink spare part kits include replacement thermal material. Description For use only with computer models with discrete graphics subsystem memory For use only with computer models with UMA graphics subsystem memory Before removing the heat sink, follow these steps: Shut down the computer.
  • Page 79 Remove the Phillips PM2.5×4.0 screw (2) that secures the heat sink to the system board. Lift the right side of the heat sink (1) until it rests at angle. NOTE: Due to the adhesive quality of the thermal material located between the heat sink and system board components, it may be necessary to move the heat sink from side to side to detach Release the heat sink (2) by sliding it to the right until it clears the left side of the top cover.
  • Page 80 Remove the heat sink (3) by sliding it up and forward. NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system board each time the heat sink is removed. Thermal paste is used on the processor (1) and the section of the heat sink (1) that services it.
  • Page 81 Following the 1, 2, 3, 4, sequence stamped into the heat sink, loosen the four Phillips PM2.5×11.0 screws (1) that secure the heat sink to the system board. Lift the right side of the heat sink (1) until it rests at an angle. NOTE: Due to the adhesive quality of the thermal material located between the heat sink and system board components, it may be necessary to move the heat sink from side to side to detach...
  • Page 82 Remove the heat sink (3) by sliding it up and forward. NOTE: The thermal material must be thoroughly cleaned from the surfaces of the heat sink and the system board each time the heat sink is removed. Thermal paste is used on the processor (1) and the section of the heat sink (1) that services it.
  • Page 83: Processor

    Processor NOTE: All processor spare part kits include replacement thermal material. Description Intel Core 2 Duo 2.80-GHz processor (1066-MHz FSB, 6-MB L2 cache) Intel Core 2 Duo 2.53-GHz processor (1066-MHz FSB, 6-MB L2 cache) Intel Core 2 Duo 2.40-GHz processor (1066-MHz FSB, 3-MB L2 cache) Intel Core 2 Duo 2.26-GHz processor (1066-MHz FSB, 3-MB L2 cache) Before removing the processor, follow these steps: Shut down the computer.
  • Page 84 Lift the processor (2) straight up and remove it. NOTE: When you install the processor, the gold triangle (3) on the processor must be aligned with the triangle (4) embossed on the processor slot. Reverse this procedure to install the processor. Chapter 4 Removal and replacement procedures...
  • Page 85: Display Assembly

    Display assembly Description 14.1-inch, WXGA AntiGlare LED display assembly for use on computer models equipped with a webcam (includes three WLAN antenna cables, two WWAN antenna cables, and two microphones) 14.1-inch, WXGA AntiGlare LED display assembly for use on computer models not equipped with a webcam (includes three WLAN antenna cables, two WWAN antenna cables, and two microphones) 14.1-inch, WXGA+ AntiGlare display assembly for use on computer models equipped with a...
  • Page 86 Remove the following: (1) Two round rubber screw covers. Screw covers are available in the Rubber Kit, spare part number 482966-001. (2) Two wedge-shaped rubber screw covers. Screw covers are available in the Rubber Kit, spare part number 482966-001. (3) Four Torx T8M2.5×7.0 screws that secure the display assembly to the computer. Turn the computer right-side up, with the front toward you.
  • Page 87 Remove the wireless antenna cables (2) from the clips and routing channels built into the top cover. CAUTION: The display assembly will be unsupported when the following screws are removed. To prevent damage to the display assembly, support it before removing the screws. Remove the two T8M2.5×7.0 screws (1) that secure the display assembly to the computer.
  • Page 88 If it is necessary to replace the display bezel or display hinges, remove the four rubber screw covers (1) and the four Phillips PM2.5×7.0 screws (2) that secure the display bezel to the display assembly. The rubber screw covers are available in the Rubber Kit, spare part number 482966-001.
  • Page 89 Remove the display hinges (2). The left and right display hinges are included in the Display Hinge Kit, spare part number 482967-001. Reverse this procedure to reassemble and install the display assembly. Component replacement procedures...
  • Page 90: Top Cover

    Top cover Description Top cover (includes TouchPad buttons) Before removing the top cover, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 91 Remove the following: (1) Two round rubber screw covers on the front edge of the base enclosure. Rubber screw covers are available in the Rubber Kit, spare part number 482968-001. (2) Two cup-shaped rubber screw covers on the right edge of the base enclosure. Rubber screw covers are available in the Rubber Kit, spare part number 482968-001.
  • Page 92: Touchpad

    Remove the top cover (2) by lifting it straight up. Reverse this procedure to install the top cover. TouchPad Description TouchPad (includes cable and TouchPad button board and cable) Before removing the TouchPad, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
  • Page 93 Remove the TouchPad bracket (3) by lifting it straight up. Release the ZIF connector (1) to which the TouchPad button board cable is attached, and disconnect the TouchPad button board cable from the TouchPad board. Remove the TouchPad board (2) by lifting it straight up. Reverse this procedure to install the TouchPad.
  • Page 94: Fingerprint Reader Board

    Fingerprint reader board Description Fingerprint reader board (includes cable) Before removing the fingerprint reader board, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.
  • Page 95: Bluetooth Module Cable

    Bluetooth module cable NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare part number 487432-001. Before removing the Bluetooth module cable, follow these steps: Shut down the computer.
  • Page 96: Speaker

    Speaker Description Speaker Before removing the speaker, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC Adapter from the computer.
  • Page 97: Audio/Expresscard Assembly

    Reverse this procedure to install the speaker. Audio/ExpressCard assembly Description Audio/ExpressCard assembly (includes ExpressCard slot, cable, headphone and microphone connectors, and SD card reader slot) Before removing the audio/ExpressCard assembly, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
  • Page 98: Modem Module Cable

    Remove the audio/ExpressCard assembly (3) by sliding it up and to the right. Reverse this procedure to install the audio/ExpressCard assembly. Modem module cable NOTE: The modem module spare part kits do not include a modem module cable. The modem module cable is included in the Cable Kit, spare part number 487432-001.
  • Page 99 Remove the RJ-11 connector (2) from the clip built into the base enclosure. Reverse this procedure to install the modem module cable. Component replacement procedures...
  • Page 100: System Board

    System board NOTE: All system board spare part kits include replacement thermal material. Description For use only with computer models with discrete graphics subsystem memory (includes 256 MB of graphics subsystem memory For use only with computer models with discrete graphics subsystem memory (includes 128 MB of graphics subsystem memory For use only with computer models with UMA graphics subsystem memory Before removing the system board, follow these steps:...
  • Page 101 ● WLAN module (see WLAN module on page ● RTC battery (see RTC battery on page ● Fan (see Fan on page ● Heat sink (see Heat sink on page ● Processor (see Processor on page Remove the system board: Disconnect the modem module cable (1) from the system board.
  • Page 102 Reverse the preceding procedure to install the system board. Chapter 4 Removal and replacement procedures...
  • Page 103: Computer Setup

    Computer Setup This user guide describes features that are common to most models. Some features may not be available on your computer. Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load.
  • Page 104: Restoring Factory Settings In Computer Setup

    NOTE: You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to navigate and make selections in Computer Setup. ● To select a menu or a menu item, use the keyboard arrow keys and then press enter, or use a pointing device to click the item.
  • Page 105: Computer Setup Menus

    Enable/disable the fingerprint reader (select models only; disabled by default). Enable/disable reset of HP ProtectTools security keys. Enter, change, or delete a BIOS administrator password. Enroll or reset HP SpareKey, which is a set of security questions and answers used if you forget your password. Computer Setup menus...
  • Page 106: Diagnostics Menu

    If you run Disk Sanitizer, the data on the primary hard drive is destroyed permanently. Enter a user-defined computer asset tracking number and ownership tag. Enable/disable a prompt for HP SpareKey enrollment. To do this ● F1 System Information—Displays the following information: ◦...
  • Page 107: System Configuration Menu

    IDE (Integrated Drive Electronics) ◦ RAID (Redundant Array of Independent Disks) NOTE: Availability of the options above varies by computer model. ● Enable/disable secondary battery fast charge (enabled by default). ● Enable/disable HP QuickLook (enabled by default). Computer Setup menus...
  • Page 108 Select Built-In Device Options Port Options (all are enabled by default) Set Security Level Restore Security Defaults 100 Chapter 5 Computer Setup To do this ● Enable/disable Virtualization Technology (select models only; enabled by default). ● Enable/disable TXT (Intel® Trusted Execution Technology) (select models only; enabled by default).
  • Page 109: Specifications

    Specifications Computer specifications Dimensions Depth Width Height (front to rear) Weight (computer equipped with an optical drive, WXGA display assembly, 1 memory module, WLAN module, and 6-cell battery) Weight (computer equipped with the optical drive weight saver, WXGA display assembly, 1 memory module, WLAN module, and 4- cell battery) Input power Operating voltage...
  • Page 110: 14.1-Inch, Wxga Display Specifications

    Operating Nonoperating NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this range of temperatures. 14.1-inch, WXGA display specifications Dimensions Height Width Diagonal Number of colors Contrast ratio Brightness Pixel resolution Pitch Format Configuration Backlight Character display...
  • Page 111: Hard Drive Specifications

    Hard drive specifications Dimensions Height Width Weight Interface type Transfer rate Security Seek times (typical read, including setting) Single track Average Maximum Logical blocks Disc rotational speed Operating temperature *1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive specifications may differ slightly.
  • Page 112: Dvd±Rw And Cd-Rw Double-Layer Combo Drive Specifications

    DVD±RW and CD-RW Double-Layer Combo Drive specifications Applicable disc Access time Random Cache buffer Data transfer rate 24X CD-ROM 8X DVD-ROM 24X CD-R 16X CD-RW 8X DVD+R 4X DVD+RW 8X DVD-R 4X DVD-RW 2.4X DVD+R(9) 5X DVD-RAM 104 Chapter 6 Specifications Read: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE...
  • Page 113: Dvd/Cd-Rw Combo Drive Specifications

    DVD/CD-RW Combo Drive specifications Applicable disc Access time Random Cache buffer Data transfer rate 24X CD-ROM 8X DVD 24X CD-R 24X CD-RW Read: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video CD), Multisession CD (Photo-CD, CD- EXTRA, Portfolio, CD-R, CD-RW), CD- R, CD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW,...
  • Page 114: Dvd-Rom Drive

    DVD-ROM Drive Applicable disc Access time Random Cache buffer Data transfer rate CD-R (24X) CD-RW (10X) CD-ROM (24X) DVD (8X) Multiword DMA mode 2 106 Chapter 6 Specifications DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18, CD-ROM (Mode 1 and 2), CD Digital Audio, CD-XA ready (Mode 2, Form 1 and Form 2), CD-I (Mode 2, Form 1 and Form 2), CD-R, CD- RW, Photo CD (single and multisession), CD-Bridge <...
  • Page 115: System Dma Specifications

    System DMA specifications Hardware DMA DMA0 DMA1* DMA2* DMA3 DMA4 DMA5* DMA6 DMA7 *ExpressCard controller can use DMA 1, 2, or 5. System function Not applicable Not applicable Not applicable Not applicable Direct memory access controller Available for ExpressCard Not assigned Not assigned System DMA specifications 107...
  • Page 116: System Interrupt Specifications

    System interrupt specifications Hardware IRQ IRQ0 IRQ1 IRQ2 IRQ3 IRQ4 IRQ5* IRQ6 IRQ7* IRQ8 IRQ9* IRQ10* IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 *Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none. NOTE: ExpressCards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. Either the infrared or the serial port may assert IRQ3 or IRQ4.
  • Page 117: System I/O Address Specifications

    System I/O address specifications I/O address (hex) 000 - 00F 010 - 01F 020 - 021 022 - 024 025 - 03F 02E - 02F 040 - 05F 044 - 05F 062 - 063 065 - 06F 070 - 071 072 - 07F 080 - 08F 090 - 091...
  • Page 118 I/O address (hex) 220 - 22F 230 - 26D 26E - 26 278 - 27F 280 - 2AB 2A0 - 2A7 2A8 - 2E7 2E8 - 2EF 2F0 - 2F7 2F8 - 2FF 300 - 31F 320 - 36F 370 - 377 378 - 37F 380 - 387 388 - 38B...
  • Page 119: System Memory Map Specifications

    System memory map specifications Size 640 KB 128 KB 48 KB 160 KB 64 KB 15 MB 58 MB 58 MB 2 MB 4 GB 64 KB Memory address 00000000-0009FFFF 000A0000-000BFFFF 000C0000-000CBFFF 000C8000-000E7FFF 000E8000-000FFFFF 00100000-00FFFFFF 04800000-07FFFFFF 04800000-07FFFFFF 08000000-080FFFFF 08200000-FFFEFFFF FFFF0000-FFFFFFFF System memory map specifications 111 System function Base memory...
  • Page 120: Screw Listing

    Screw listing This section provides specification and reference information for the screws and screw locks used in the computer. All screws listed in this section are available in the Screw Kit, spare part number 486305-001. 112 Chapter 7 Screw listing...
  • Page 121: Phillips Pm2.0×5.0 Captive Screw

    Phillips PM2.0×5.0 captive screw Color Black Where used: (1) One captive screw that secures the Bluetooth module compartment cover to the computer (screw is secured with a C-clip) (2) Two captive screws that secure the hard drive bay cover to the computer (screws are secured with C-clips) (3) One captive screw that secures the memory module compartment cover to the computer (screw is secured with a C-clip)
  • Page 122: Phillips Pm2.5×11.0 Captive Screw

    Phillips PM2.5×11.0 captive screw Color Black Where used: One captive screw that secures the hard drive to the computer (screw is secured by a C- clip) Where used: One captive screw that secures the hard drive to the upgrade bay cradle (screw is secured by a C-clip) 114 Chapter 7 Screw listing Quantity...
  • Page 123: Phillips Pm3.0×4.0 Screw

    Phillips PM3.0×4.0 screw Color Silver Where used: 4 screws that secure the hard drive bracket to the hard drive Quantity Length 4.0 mm Thread Head diameter 3.0 mm 5.0 mm Phillips PM3.0×4.0 screw 115...
  • Page 124: Phillips 2.5×9.0 Captive Screw

    Phillips 2.5×9.0 captive screw Color Black Where used: (1) One captive screw that secures the optical drive or upgrade bay device to the computer (screw is secured by a C-clip) (2) Three captive screws that secure the keyboard to the computer (screws are secured by C-clips) 116 Chapter 7 Screw listing Quantity Length...
  • Page 125: Phillips Pm2.0×3.0 Screw

    Phillips PM2.0×3.0 screw Color Silver Where used: 2 screws that secure the optical drive bracket to the optical drive Quantity Length 3.0 mm Thread Head diameter 2.0 mm 4.5 mm Phillips PM2.0×3.0 screw 117...
  • Page 126: Phillips Pm2.5×4.0 Screw

    Phillips PM2.5×4.0 screw Color Black Where used: 4 screws that secure the upgrade bay device to the computer Where used: One screw that secures the heat sink to the system board on computer models equipped with discrete graphics subsystem memory 118 Chapter 7 Screw listing Quantity Length...
  • Page 127: Phillips Pm2.5×4.0 Screw

    Phillips PM2.5×4.0 screw Color Silver Where used: 2 screws that secure the WWAN module to the system board Where used: (1) Two screws that secure the modem module to the system board Quantity Length 4.0 mm Thread Head diameter 2.5 mm 5.0 mm Phillips PM2.5×4.0 screw 119...
  • Page 128 (2) Two screws that secure the WLAN module to the system board Where used: One screw that secures the power button board to the switch cover Where used: 2 screws that secure the display inverter to the display enclosure Where used: 4 screws that secure the TouchPad bracket to the top cover 120 Chapter 7 Screw listing...
  • Page 129: Phillips Pm2.0×3.0 Broad-Head Screw

    Where used: 2 screws that secure the audio/ExpressCard assembly to the top cover Where used: (1) Three screws that secure the system board to the base enclosure on all computer models (2) One screw that secures the system board to the base enclosure on computer models equipped with UMA graphics subsystem memory Phillips PM2.0×3.0 broad-head screw Phillips PM2.0×3.0 broad-head screw 121...
  • Page 130 Color Black Where used: 2 screws that secure the switch cover to the computer 122 Chapter 7 Screw listing Quantity Length 3.0 mm Thread Head diameter 2.0 mm 6.0 mm...
  • Page 131: Torx8 T8M2.5×7.0 Screw

    Torx8 T8M2.5×7.0 screw Color Black Where used: 3 screws that secure the switch cover to the computer Where used: 4 screws that secure the display assembly to the computer Quantity Length 7.0 mm Thread Head diameter 2.5 mm 5.0 mm Torx8 T8M2.5×7.0 screw 123...
  • Page 132 Where used: 2 screws that secure the display assembly to the computer Where used: 7 screws that secure the top cover to the base enclosure Where used: One screw that secures the speaker to the base enclosure 124 Chapter 7 Screw listing...
  • Page 133: Phillips Pm2.5×7.0 Screw

    Phillips PM2.5×7.0 screw Color Black Where used: One screw that secures the fan to the base enclosure Where used: 4 screws that secure the display bezel to the display enclosure Quantity Length 7.0 mm Thread Head diameter 2.5 mm 5.0 mm Phillips PM2.5×7.0 screw 125...
  • Page 134 Where used: 2 screws that secure the hinges to the display enclosure 126 Chapter 7 Screw listing...
  • Page 135: Phillips Pm2.5×11.0 Captive Screw

    Phillips PM2.5×11.0 captive screw Color Silver Where used: 4 captive screws that secure the heat sink to the system board (screws are secured by C-clips) Quantity Length 11.0 mm Thread Head diameter 2.5 mm 5.0 mm Phillips PM2.5×11.0 captive screw 127...
  • Page 136: Phillips Pm2.0×5.0 Screw

    Phillips PM2.0×5.0 screw Color Black Where used: One screw that secures the top cover to the base enclosure 128 Chapter 7 Screw listing Quantity Length 5.0 mm Thread Head diameter 2.0 mm 5.0 mm...
  • Page 137: Backup And Recovery In Windows Vista

    In case of system instability or failure, you can use the backup files to restore the contents of your computer. When creating backups, HP recommends the following sequence: Create a set of recovery discs of the entire hard drive as soon as possible after you set up your computer.
  • Page 138: Creating Recovery Discs

    Creating recovery discs After setting up the computer, create a set of recovery discs for the initial backup of the entire hard drive. NOTE: This process may take over an hour, depending on your computer speed and the amount of data being stored.
  • Page 139: Backing Up Your Information

    Backing up your information After you create the recovery discs for the initial backup of the entire hard drive, you should schedule automatic backups of your files. You should also back up your files before you modify the hardware or software.
  • Page 140: Backing Up Individual Files Or Folders

    Backing up individual files or folders When you perform a backup of the entire hard drive, you are saving the full factory image, including the Windows operating system, software programs, all personal files and folders, and configuration settings. You can back up a copy of the entire hard drive to either of the following locations: ●...
  • Page 141: Creating System Restore Points

    Subsequent recovery points make copies of changes made after that time. HP recommends that you create manual restore points at the following times: ● Before you add or extensively modify software or hardware ●...
  • Page 142: Performing A Recovery

    Performing a recovery In case of hard drive failure or system instability, the computer provides tools to recover your files. You can recover your information using the following methods: NOTE: Have your backup files available. Some of these methods will prompt you for your backup files stored on recovery discs or on a drive.
  • Page 143: Restoring The Computer To A Previous State

    Restoring the computer to a previous state Your computer automatically creates restore points daily (depending on your computer activity) and when you make a major change to the computer, such as adding software or a new driver. If you decide to reverse changes made to the computer, you can revert back to a previous restore point.
  • Page 144: Recovering Information Using Windows Recovery Environment (Winre)

    Recovering information using Windows Recovery Environment (WinRE) Windows Recovery Environment (WinRE) can perform a recovery from either an optional external hard drive where you have backed up your information or from recovery discs that you previously created. CAUTION: Using Windows Recovery Environment (WinRE) will completely erase hard drive contents and reformat the hard drive.
  • Page 145: Recovering Information Using Recovery Manager

    The recovery tool reinstalls the operating system and HP programs and drivers that were installed at the factory. Software not installed at the factory must be reinstalled.
  • Page 146: Recovering Information Using A Windows Vista Operating System Dvd (Purchased Separately)

    Make sure that your most recent backup of the hard drive (stored on recovery discs or on an external drive) is easily accessible. To order a Windows Vista operating system DVD, go to http://www.hp.com/ support, select your country or region, and follow the on-screen instructions. You can also order the DVD by calling technical support.
  • Page 147: Backup And Recovery In Windows Xp

    Backing up your information NOTE: You can recover only the files that you have previously backed up. HP recommends that you use the Windows backup utility to create a hard drive backup as soon as you set up your computer.
  • Page 148: Backup Suggestions

    Backup suggestions ● Connect the computer to external power before performing backup and recovery procedures. ● Create system recovery points. ● Store personal files in the My Documents folder and back up these folders periodically. ● Back up templates stored in their associated programs. ●...
  • Page 149: Backing Up All Files And Folders

    The first system recovery point, a snapshot of the entire image, is automatically created the first time you perform a backup. Subsequent recovery points make copies of changes made after that time. HP recommends that you create recovery points at the following times: ● Before you add or extensively modify software or hardware ●...
  • Page 150: Scheduling Backups

    Scheduling backups You can schedule backups for the entire system, for recovery points, or for specific files and folders. Backups can be scheduled at specific intervals (daily, weekly, or monthly) or at specific events, such as at system restart or when you log on. To schedule backups: Select Start >...
  • Page 151: 10 Connector Pin Assignments

    10 Connector pin assignments 1394 Assignment Power Ground TPB- TPB+ TPA- TPA+ 1394 143...
  • Page 152: Audio-In (Microphone)

    Audio-in (microphone) Audio-out (headphone) 144 Chapter 10 Connector pin assignments Signal Audio signal in Audio signal in Ground Signal Audio out, left channel Audio out, right channel Ground...
  • Page 153: External Monitor

    External monitor Signal Red analog Green analog Blue analog Not connected Ground Ground analog Ground analog Ground analog +5 VDC Ground Monitor detect DDC 2B data Horizontal sync Vertical sync DDC 2B clock External monitor 145...
  • Page 154: Modem)

    RJ-11 (modem) RJ-45 (network) 146 Chapter 10 Connector pin assignments Signal Unused Ring Unused Unused Unused Signal Transmit + Transmit - Receive + Unused Unused Receive - Unused Unused...
  • Page 155: Universal Serial Bus

    Universal Serial Bus Signal +5 VDC Data - Data + Ground Universal Serial Bus 147...
  • Page 156: 11 Power Cord Set Requirements

    11 Power cord set requirements The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC or from 220 to 240 volts AC. The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased.
  • Page 157: Requirements For Specific Countries And Regions

    Requirements for specific countries and regions Country/region Australia Austria Belgium Canada Denmark Finland France Germany Italy Japan The Netherlands Norway The People's Republic of China South Korea Sweden Switzerland Taiwan The United Kingdom The United States The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.
  • Page 158: 12 Recycling

    When you remove these components, handle them carefully. NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities, or see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
  • Page 159 Perform the following steps to disassemble the display assembly: Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly.
  • Page 160 Disconnect all display panel cables (1) from the display inverter and remove the display inverter (2). Remove all screws (1) that secure the display panel assembly to the display enclosure. Remove the display panel assembly (2) from the display enclosure. Turn the display panel assembly upside down.
  • Page 161 Remove the display panel frame (2) from the display panel. Remove the screws (1) that secure the backlight cover to the display panel. Lift the top edge of the backlight cover (2) and swing it outward. Remove the backlight cover. Turn the display panel right-side up.
  • Page 162 Remove the backlight cables (1) from the clip (2) in the display panel. Turn the display panel upside down. WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. Remove the backlight frame from the display panel.
  • Page 163 Remove the backlight from the backlight frame. Disconnect the display panel cable (1) from the LCD panel. Remove the screws (2) that secure the LCD panel to the display rear panel. Release the LCD panel (3) from the display rear panel. Release the tape (4) that secures the LCD panel to the display rear panel.
  • Page 164: Index

    Index Symbols/Numerics 1394 port location 16 pin assignments 143 AC adapter, spare part numbers 28, 29 accessory battery connector 17 AHCI (Advanced Host Controller Interface) 99 ambient light sensor 8 antenna components 9 disconnecting 56, 63 locations 9 spare part number 20, 30 audio, product description 3 audio-in jack location 16...
  • Page 165 70 spare part numbers 21, 31, hinge removal 81 spare part number 20, 30, HP QuickLook 99 HP SpareKey Enrollment 97 I/O address specifications 109 IDE (Integrated Drive Electronics) 99 info button 10 internal display switch 10 interrupt specifications 108...
  • Page 166 jacks audio-in 16 audio-out 16 headphone 16 microphone 16 modem 15 network 15 RJ-11 15 RJ-45 15 key components 11 keyboard product description 5 removal 57 spare part numbers 20, 30, keyboard light 8 keyboard light button 8 keyboard shield removal 67 keypad keys 11 keys...
  • Page 167 15 Security menu Automatic DriveLock 98 change password 97 Disk Sanitizer 98 DriveLock 98 fingerprint reader reset 97 HP SpareKey 97 password policy 97 System IDs 98 user management 97 security, product description 5 serial number 18 service considerations 35...
  • Page 168 system information 97 system memory map 111 system points 135 system recovery points 141 thermal material, replacement 72, 74 tools required 35 top components 8 top cover removal 82 spare part number 23, 32, TouchPad location 13 spare part number 23, 32 TouchPad board removal 84 spare part number 84...

Table of Contents