Sign in today to find solutions:

Don't have an account? Sign up

HP EliteBook 2540P Maintenance And Service Manual

Hp elitebook 2540p: user guide.

 
HP EliteBook 2540p Notebook PC
Maintenance and Service Guide

Summary of Contents

  • Page 1

    HP EliteBook 2540p Notebook PC Maintenance and Service Guide...

  • Page 2

    Corporation. SD Logo is a trademark of its proprietor. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.

  • Page 3

    Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.

  • Page 4

    Safety warning notice ENWW...

  • Page 5: Table Of Contents

    Table of contents 1 Product description ... 1 2 External component identification ... 7 Display components ... 8 Buttons and fingerprint reader ... 10 Keys ... 13 Pointing device components ... 14 Front components ... 15 Left-side components ... 16 Rear components ...

  • Page 6: Table Of Contents

    Component replacement procedures ... 46 Service tag ... 46 Computer feet ... 47 Battery ... 48 SIM ... 49 Bluetooth module ... 50 Expansion memory module ... 52 Low-voltage hard drive or solid-state drive ... 54 WLAN module ... 57 WWAN module ...

  • Page 7: Table Of Contents

    Windows XP ... 117 Starting Computer Setup ... 117 Using Computer Setup ... 117 Computer Setup menus ... 119 6 Specifications ... 125 Computer specifications ... 125 12.1-in display specifications ... 126 Hard drive specifications ... 127 DVD±RW and CD-RW SuperMulti Double-Layer Drive specifications ... 128 DVD-ROM Drive specifications ...

  • Page 8: Table Of Contents

    RJ-45 (network) ... 146 Universal Serial Bus ... 147 9 Power cord set requirements ... 149 Requirements for all countries ... 149 Requirements for specific countries and regions ... 150 10 Recycling ... 151 Battery ... 151 Display ... 151 Index ...

  • Page 9: Product Description

    Product description Category Description Product Name HP EliteBook 2540p Notebook PC Processors Intel® Dual Core™ processors (support Intel Turbo Boost Technology): ● ● ● ● Chipset Mobile Intel QM57 Express chipset (non-HDI) Graphics Intel HD Graphics with up to 512-MB unified memory architecture (UMA) graphics subsystem...

  • Page 10

    Category Internal storage Optical drives Chapter 1 Product description Description Supports the following configurations: ● 8192-MB total system memory (4096 × 2) ● 6144-MB total system memory (4096 + 2048) ● 4096-MB total system memory (4096 × 1, 2048 × 2) ●...

  • Page 11

    Category Description 9.5-mm tray load Supports the following drives: ● ● Audio and video Integrated dual-array microphones IDT 92HD75B high-definition (HD) audio Supports 2 stereo speakers Integrated 2.0-megapixel webcam with macro focus for business card reader Modem 56K V.92 1.5-in data/fax modem Supports “no modem”...

  • Page 12

    Full-size keyboard Dual point (pointing stick and TouchPad with scroll zone) Spill-resistant keyboard with HP drainage system 65-W HP Smart AC adapter with localized cable plug support (3-wire plug with ground pin, supports 3-pin DC connector) Supports HP Fast-Charge technology Supports the following primary batteries: ●...

  • Page 13

    Category Description Operating system Preinstalled: ● ● ● ● ● ● Preinstalled with Microsoft® Office: ● ● ● ● ● ● ● ● ● Restore media (OSDVD): ● ● ● ● ● ● Certified: SUSE Linux Enterprise Desktop Office restore media: Office Ready restore DVD DRDVD (Device driver and Application DVD): ●...

  • Page 14

    Category Serviceability Chapter 1 Product description Description Supported: ● Microsoft WHQL ● Novell Web-only support: ● Windows 7 Enterprise 32/64 ● Windows 7 Ultimate 32/64 ● Windows Vista Business 64 ● Windows Vista Enterprise 32/64 End-user replaceable parts: ● AC adapter ●...

  • Page 15: External Component Identification

    External component identification Components included with the computer may vary by region and model. The illustrations in this chapter identify the standard features on most computer models. To see a list of hardware installed in the computer, follow these steps: In Windows 7: ▲...

  • Page 16: Display Components

    Display components Item Component WWAN antennas (2)* WLAN antennas (2)* Webcam light Webcam Keyboard light and button Internal microphones (2) Chapter 2 External component identification Description Send and receive wireless signals to communicate with WWANs (select models only). Send and receive wireless signals to communicate with WLANs (select models only).

  • Page 17

    Item Component Ambient light sensor *The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennas free from obstructions. To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or region.

  • Page 18: Buttons And Fingerprint Reader

    Buttons and fingerprint reader Chapter 2 External component identification ENWW...

  • Page 19

    ● When the computer is on, press the button to open HP Software Setup. NOTE: If HP Software Setup is not available, the default Web browser opens. ● When the computer is off, press the button to open HP QuickWeb.

  • Page 20

    Item Component Volume up button Fingerprint reader (select models only) Chapter 2 External component identification Description Increases speaker volume. Allows a fingerprint logon to Windows, instead of a password logon. ENWW...

  • Page 21: Keys

    Keys Item Component Windows logo key Windows applications key Embedded numeric keypad keys Function keys ENWW Description Displays system information when pressed in combination with the key. Executes frequently used system functions when pressed in combination with a function key or the key.

  • Page 22: Pointing Device Components

    Pointing device components Item Component Left TouchPad button* TouchPad* Left pointing stick button* Pointing stick* TouchPad on/off button Right pointing stick button* TouchPad scroll zone Right TouchPad button* *This table describes factory settings. To view or change pointing device preferences: ●...

  • Page 23: Front Components

    Holds a business card in position so that the webcam can capture the information on the card. ● Blue: An integrated wireless device, such as a WLAN device, the HP Mobile Broadband Module (select models only), and/or a Bluetooth device, is on. ●...

  • Page 24: Left-side Components

    Left-side components NOTE: Refer to the illustration that most closely matches your computer. Computer model equipped with a low-voltage processor Item Component Power connector RJ-11 (modem) jack Powered USB port Optical drive Smart card reader Computer model equipped with a standard-voltage processor Item Component Power connector...

  • Page 25: Rear Components

    Rear components Item Component RJ-45 network) jack USB ports (2) ENWW Description Connects a network cable. Connect optional USB devices. Rear components...

  • Page 26: Right-side Components

    Right-side components Item Component ExpressCard34 slot Docking connector Security cable slot Vent DisplayPort External monitor port Audio-out (headphone) jack/Audio-in (microphone) jack 1394 port SD Card Reader Chapter 2 External component identification Description Supports optional ExpressCards. Connects an optional docking device. Attaches an optional security cable to the computer.

  • Page 27: Bottom Components

    Bottom components Item Component Battery release latches (2) Battery bay Vents (7) SIM slot (select models only) Hard drive bay and memory module compartment Speakers (2) ENWW Description Release the battery from the battery bay. Holds the battery. Enable airflow to cool internal components. NOTE: The computer fan starts up automatically to cool internal components and prevent overheating.

  • Page 28

    Component Wireless module compartment Optical drive bay or hard drive bay Chapter 2 External component identification Description Contains an HP Mobile Broadband Module (select models only) and a WLAN module (select models only). CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless...

  • Page 29: Illustrated Parts Catalog, Serial Number Location

    Illustrated parts catalog Serial number location The service tag, affixed to the bottom of the computer, provides information that may be needed when troubleshooting system problems. The service tag provides the following information: (1) Product name: This is the product name affixed to the front of the computer. (2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.

  • Page 30

    Chapter 3 Illustrated parts catalog ENWW...

  • Page 31: Computer Major Components

    Computer major components ENWW Computer major components...

  • Page 32

    Item Description 12.1-in, WXGA AntiGlare LED display assembly (includes display panel cable, WLAN antenna transceivers and cables, and WWAN antenna transceivers and cables. See assembly component spare part number information.): For use only with computer models equipped with a webcam For use only with computer models not equipped with a webcam Switch cover (includes display lid switch board and cable and capacitive board and cable)

  • Page 33

    Item Description ● For use in Thailand ● For use in Turkey ● For use in the United Kingdom ● For use in the United States RTC battery Memory shield Memory modules (2, 1333-MHz, DDR3): 4 GB Top cover (includes TouchPad board and cable, TouchPad button board and cable, and TouchPad bracket): For use only with computer models equipped with a fingerprint reader For use only with computer models not equipped with a fingerprint reader Plastics Kit, includes:...

  • Page 34

    3-cell, 31-WH, 2.8-AH, Li-ion battery 3-cell, 28-WH, 2.8-AH, Li-ion long life battery (21) HP Integrated Module with Bluetooth 2.1 Wireless Technology NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare part number 598766-001.

  • Page 35

    Item Description Broadcom 43224AGN 802.11a/b/g/draft-n WiFi Adapter for use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States, Venezuela, and Vietnam Broadcom 43224AGN 802.11a/b/g/draft-n WiFi Adapter for use in Afghanistan, Albania,...

  • Page 36

    HP un2420 Broadband Module for use in all countries and regions HP hs2330 HSPA Mobile Broadband Module for use in all countries and regions HP hs2320 HSPA Mobile Broadband Module for use only in Europe, the Middle East, and Africa NOTE: For use only on selected computer models.

  • Page 37

    Item Description 6.35-cm (2.50-in) hard drive: NOTE: The 6.35-cm (2.50-in) hard drive must be installed in the optical drive bay, using a hard drive carrier. Installation of these devices in the hard drive bay is not supported. (This option is not available when the optical drive is installed.) ●...

  • Page 38

    Display components Item Description Display bezel For use only with computer models equipped with a webcam For use only with computer models not equipped with a webcam Webcam module Ambient light sensor board Display Hinge Kit, includes: Display panel cable (includes webcam module cable and ambient light sensor board cable) Display enclosure (includes microphone receivers and cables, WLAN antenna cables and transceivers, and WWAN antenna cables and transceivers)

  • Page 39: Mass Storage

    Mass storage Item Description 6.35-cm (2.50-in) mass storage device NOTE: 6.35-cm (2.50-in) devices must be installed in the optical drive bay, using a hard drive carrier. Installation of 6.35-cm (2.50-in) devices in the hard drive bay is not supported. 6.35-cm (2.50-in) mass storage devices available for use on computer models equipped with a standard-voltage (35-W) processor: ●...

  • Page 40

    Item Description 4.57-cm (1.80-in) mass storage device NOTE: 4.57-cm (1.80-in) devices must be installed in the hard drive bay. Installation of these devices in the optical drive bay is not supported. 4.57-cm (1.80-in) mass storage devices available for use on computer models equipped with a low-voltage (25- W) processor: ●...

  • Page 41: Plastics Kit

    Plastics Kit Item Description Plastics Kit: Optical drive bezel Wireless module compartment cover (includes one captive screw, secured by a C-clip) ExpressCard slot bezel Memory module compartment cover (includes one captive screw, secured by a C-clip) Display hinge covers Bluetooth module compartment cover (includes one captive screw, secured by a C-clip) ENWW Spare part number 598796-001...

  • Page 42: Miscellaneous Parts

    AC adapter 65-W non-PFC AC adapter 65-W PFC AC adapter Cable Kit (includes Bluetooth module cable and modem module cable) HP 2540 Series Docking Station Power cord For use in Argentina For use in Australia and New Zealand For use in Brazil...

  • Page 43: Sequential Part Number Listing

    572509-001 Intel Centrino Advanced-N 6200 WLAN module for use in Canada and the United States 574248-001 HP hs2320 HSPA Mobile Broadband Module for use only in Europe, the Middle East, and Africa NOTE: 574249-001 HP hs2330 HSPA Mobile Broadband Module for use in all countries and regions ENWW The modem module spare part kit does not include a modem module cable.

  • Page 44

    Spare part Description number 582562-001 Broadcom 4312G 802.11b/g WiFi Adapter for use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States, Venezuela, and Vietnam 582562-002...

  • Page 45

    Display panel cable (includes webcam module cable and ambient light sensor board cable) 598773-001 Display Hinge Kit (includes left and right display hinges and left and right hinge covers) 598774-001 HP 2540 Series Docking Station 598775-001 DVD-ROM Drive 598776-001 DVD±RW and CD-RW Super Multi Double-Layer Drive 598777-001 4.57-cm (1.80-in), 160-GB, 5400-rpm hard drive...

  • Page 46

    Spare part Description number 598789-001 Fan/heat sink assembly for use only with 35-W processors (includes replacement thermal material and replacement thermal material cleaning kit) 598790-001 Keyboard for use in the United States (includes cable) 598790-031 Keyboard for use in the United Kingdom (includes cable) 598790-041 Keyboard for use in Germany (includes cable) 598790-051...

  • Page 47

    Spare part Description number 598794-001 12.1-in, WXGA AntiGlare LED display assembly for use only with computer models equipped with a webcam (includes display panel cable, WLAN antenna transceivers and cables, and WWAN antenna transceivers and cables. 598795-001 12.1-in, WXGA AntiGlare LED display assembly for use only with computer models not equipped with a webcam (includes display panel cable, WLAN antenna transceivers and cables, and WWAN antenna transceivers and cables.

  • Page 48

    Chapter 3 Illustrated parts catalog ENWW...

  • Page 49: Removal And Replacement Procedures, Preliminary Replacement Requirements, Tools Required, Service Considerations, Plastic Parts

    Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Magnetic screwdriver ● Phillips P0 and P1 screwdrivers ● Torx T8 screwdriver Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.

  • Page 50: Cables And Connectors, Drive Handling

    Cables and connectors CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion.

  • Page 51: Grounding Guidelines, Electrostatic Discharge Damage

    Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.

  • Page 52: Packaging And Transporting Guidelines, Workstation Guidelines

    Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.

  • Page 53: Equipment Guidelines

    Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times.

  • Page 54: Service Tag, Component Replacement Procedures

    Component replacement procedures This chapter provides removal and replacement procedures. There are as many as 72 screws that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement. Service tag The service tag, affixed to the bottom of the computer, provides information that may be needed when troubleshooting system problems.

  • Page 55: Computer Feet

    Computer feet The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare part number 598797-001. There are 5 rubber feet that attach to the base enclosure in the locations illustrated below. There are two different sized feet: the four square feet (1) are installed in the four corners of the base enclosure.

  • Page 56: Battery

    Battery Description 9-cell, 93-WH, 2.8-WH Li battery 6-cell, 62-WH, 2.8-WH Li battery 6-cell, 55-WH, 2.8-WH Li long life battery 3-cell, 31-WH, 2.8-WH Li battery 3-cell, 28-WH, 2.8-WH Li long life battery Before disassembling the computer, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

  • Page 57

    NOTE: This section applies only to computer models with WWAN capability. NOTE: If there is a SIM inserted in the SIM slot, it must be removed before disassembling the computer. Be sure that the SIM is reinserted in the SIM slot after reassembling the computer. Before removing the SIM, follow these steps: Shut down the computer.

  • Page 58: Bluetooth Module

    Bluetooth module Description HP Integrated Module with Bluetooth 2.1 Wireless Technology NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare part number 598766-001. Before removing the Bluetooth module, follow these steps: Shut down the computer.

  • Page 59

    Remove the Bluetooth module (2) from the Bluetooth module compartment cover. The Bluetooth module compartment cover is included in the Plastics Kit, spare part number 598796-001. Remove the Bluetooth module. Reverse the above procedure to install the Bluetooth module. ENWW Component replacement procedures...

  • Page 60: Expansion Memory Module

    Expansion memory module Description 4096-MB memory module (1333-MHz, DDR3) 2048-MB memory module (1333-MHz, DDR3) 1024-MB memory module (1333-MHz, DDR3) Before removing the memory module, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

  • Page 61

    Remove the memory module (2) by pulling the module away from the slot at an angle. NOTE: The memory module is designed with a notch to prevent incorrect insertion into the memory module slot. Reverse this procedure to install the memory module. ENWW Component replacement procedures...

  • Page 62: Low-voltage Hard Drive Or Solid-state Drive

    Low-voltage hard drive or solid-state drive NOTE: The 4.57-cm (1.80-in) hard drive and solid-state drive spare part kit includes a hard drive or solid-state drive bracket. Description 4.57-cm (1.80-in), 320-GB, 5400-rpm hard drive 4.57-cm (1.80-in), 250-GB, 5400-rpm hard drive 4.57-cm (1.80-in), 160-GB, 5400-rpm hard drive 4.57-cm (1.80-in), 160-GB, solid-state drive 4.57-cm (1.80-in), 80-GB, solid-state drive Before removing the low-voltage hard drive or solid-state drive, follow these steps:...

  • Page 63

    Lift the right edge of the hard drive shield (2), swing it up and to the left, and then remove the cover (3) by sliding it up and to the right at an angle. The hard drive shield is included in the hard drive spare part kit.

  • Page 64

    If it is necessary to replace the rubber isolator, separate the edges of the isolator from the end of the low-voltage hard drive, and remove the isolator. If it is necessary to replace the low-voltage hard drive connector, slide the connector off of the hard drive.

  • Page 65: Wlan Module

    WLAN module Description Broadcom 43224AGN 802.11a/b/g/draft-n WiFi Adapter for use in Antigua and Barbuda, Argentina, Aruba, the Bahamas, Barbados, Bermuda, Brunei, Canada, the Cayman Islands, Chile, Colombia, Costa Rica, the Dominican Republic, Ecuador, El Salvador, Guam, Guatemala, Haiti, Honduras, Hong Kong, India, Indonesia, Malaysia, Mexico, Panama, Paraguay, Peru, Saudi Arabia, Taiwan, Uruguay, the United States, Venezuela, and Vietnam Broadcom 43224AGN 802.11a/b/g/draft-n WiFi Adapter for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan,...

  • Page 66

    Description Broadcom 4312G 802.11b/g WiFi Adapter for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cambodia, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador,...

  • Page 67

    Lift the right edge of the wireless module compartment cover (2), swing it up and to the left, and remove the cover. The wireless module compartment cover is included in the Plastics Kit, spare part number 598796-001. Disconnect the WLAN antenna cables (1) from the terminals on the WLAN module. NOTE: The black WLAN antenna cable is connected to the WLAN module “Main”...

  • Page 68

    Remove the WLAN module (3) by pulling the module away from the slot at an angle. NOTE: WLAN modules are designed with a notch (4) to prevent incorrect insertion. NOTE: If the WLAN antennas are not connected to the terminals on the WLAN module, the protective sleeves must be installed on the antenna connectors, as shown in the following illustration.

  • Page 69: Wwan Module

    HP un2420 Broadband Module for use in all countries and regions HP hs2330 HSPA Mobile Broadband Module for use in all countries and regions HP hs2320 HSPA Mobile Broadband Module for use only in Europe, the Middle East, and Africa NOTE: For use only on selected computer models.

  • Page 70

    Remove the WWAN module (3) by pulling the module away from the slot at an angle. NOTE: WWAN modules are designed with a notch (4) to prevent incorrect insertion. NOTE: If the WWAN antennas are not connected to the terminals on the WWAN module, the protective sleeves must be installed on the antenna connectors, as shown in the following illustration.

  • Page 71: Optical Drive

    Optical drive NOTE: The optical drive is an optional feature and is available only on computer models equipped with a low voltage (25-W) processor. Description DVD±RW and CD-RW SuperMulti Double-Layer Drive DVD-ROM Drive Before removing the optical drive, follow these steps: Shut down the computer.

  • Page 72

    Remove the optical drive (2) from the computer. If it is necessary to replace the optical drive bracket, position the optical drive with the rear toward you. Remove the two Phillips PM2.0×4.0 screws (1) that secure the optical drive bracket to the optical drive.

  • Page 73: Standard-voltage Hard Drive Or Solid-state Drive

    Standard-voltage hard drive or solid-state drive NOTE: Installation of the 6.35-cm (2.50-in) hard drive or solid-state drive in the hard drive bay is not supported. The 6.35-cm (2.50-in) hard drive or solid-state drive cannot be installed when the optical drive is installed. Description 2.50-in, 500-GB, 7200-rpm hard drive 2.50-in, 320-GB, 7200-rpm hard drive...

  • Page 74

    Remove the standard-voltage hard drive: Remove the four Phillips PM3.0×3.0 screws (1) and the two Phillips PM2.0×5.0 screws (2) that secure the hard drive carrier to the computer. Chapter 4 Removal and replacement procedures ENWW...

  • Page 75

    Insert a flat-bladed screwdriver or similar tool into the optical drive tab access (1) and press the tab to the right to release the hard drive carrier (2) from the computer. Remove the four Phillips PM3.0×3.0 screws that secure the standard-voltage hard drive to the hard drive carrier.

  • Page 76

    Remove the standard-voltage hard drive (2) by sliding it up and away from the hard drive carrier at an angle. Reverse the above procedure to reassemble and install the standard-voltage hard drive. Chapter 4 Removal and replacement procedures ENWW...

  • Page 77: Switch Cover And Keyboard

    Switch cover and keyboard Description Switch cover (includes power button board and cable) Keyboard for use in country/ region Belgium Brazil Bulgaria The Czech Republic Denmark France French Canada Germany Greece Hungary Iceland Israel Italy Japan Latin America The Netherlands Before removing the switch cover and keyboard, follow these steps: Shut down the computer.

  • Page 78

    Loosen the four captive screws (2) that secure the keyboard to the computer. Turn the computer right-side up, with the front toward you. Open the display as far as possible. Lift the right side of the switch cover (1) to detach it from the computer. Release the switch cover (2) as far as the power button board and capacitive board cables allow.

  • Page 79

    Swing the rear edge of the keyboard (3) up and forward until the keyboard rests upside down on the palm rest. Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and then disconnect the keyboard cable (2) from the system board. Release the ZIF connector (3) to which the pointing stick cable is attached, and then disconnect the pointing stick cable (4) from the system board.

  • Page 80

    Remove the switch cover (3). Reverse this procedure to install the switch cover and keyboard. Chapter 4 Removal and replacement procedures ENWW...

  • Page 81: Rtc Battery

    RTC battery Description RTC battery Before removing the RTC battery, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.

  • Page 82: Primary Memory Module

    Primary memory module Description 4096-MB memory module (1333-MHz, DDR3) 2048-MB memory module (1333-MHz, DDR3) 1024-MB memory module (1333-MHz, DDR3) Memory shield (includes one captive screw) Before removing the primary memory module, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

  • Page 83

    Spread the retaining tabs (1) on each side of the memory module slot to release the memory module. (The edge of the module opposite the slot rises away from the computer.) Remove the memory module (2) by pulling the module away from the slot at an angle. NOTE: The memory module is designed with a notch to prevent incorrect insertion into the memory module slot.

  • Page 84: Display Assembly

    Display assembly Description 12.1-in, WXGA AntiGlare LED display assembly for use only with computer models equipped with a webcam (includes display panel cable, WLAN antenna transceivers and cables, and WWAN antenna transceivers and cables. 12.1-in, WXGA AntiGlare LED display assembly for use only with computer models not equipped with a webcam (includes display panel cable, WLAN antenna transceivers and cables, and WWAN antenna transceivers and cables.

  • Page 85

    Turn the computer right-side up, with the front toward you. Open the display as far as it will open. Disconnect the display panel cable (1) from the system board and release it from the clip built into the top cover. Release the wireless antenna cables from the clips (2) built into the top cover.

  • Page 86

    Release the microphone cable and the wireless antenna cables from the clips (2) built into the top cover. CAUTION: The display assembly will be unsupported when the following screws are removed. To prevent damage to the display assembly, support it before removing the screws. Remove the two Torx T8M2.5×6.0 screws (1) that secure the display assembly to the computer.

  • Page 87

    Lift the display assembly straight up to remove it (3). ENWW Component replacement procedures...

  • Page 88

    If it is necessary to replace the display bezel or any of the display assembly internal components: Remove the four rubber screw covers (1) and the four Torx T8M2.5×5.0 screws (2) that secure the display bezel to the display assembly. NOTE: screw covers on the display bezel bottom edge.

  • Page 89

    Remove the display bezel (4). The display bezel is available using spare part numbers 598770-001 (for use only with computer models equipped with a webcam) and 598771-001 (for use only with computer models not equipped with a webcam). If it is necessary to replace the ambient light sensor board: Release the ZIF connector to which the ambient light sensor board is connected, and then disconnect the cable (1) from the board.

  • Page 90

    Remove the ambient light sensor board (3). The ambient light sensor board is available using spare part number 598761-001. If it is necessary to replace the webcam module, display hinges, display panel cable, or display enclosure: Release the display panel cable (1) from the clips built into the display enclosure. Disconnect the display panel cable (2) from the ambient light sensor board.

  • Page 91

    Disconnect the display panel cable (3) from the passthrough board. Remove the display panel. Remove the two Phillips PM2.0×4.0 screws (1) that secure each display hinge to the display panel. Remove the display hinges (2). The display hinges are included in the Display Hinge Kit, spare part number 598773-001.

  • Page 92

    m. Route the webcam module cable (3) through the slot built into the display enclosure. Reverse this procedure to reassemble and install the display assembly. Chapter 4 Removal and replacement procedures ENWW...

  • Page 93: Top Cover

    Top cover NOTE: The top cover spare part kit includes the TouchPad board and cable, TouchPad button board and cable, and TouchPad bracket. Description For use only on computer models equipped with a fingerprint reader (includes fingerprint reader and cable) For use only on computer models not equipped with a fingerprint reader Before removing the top cover, follow these steps: Shut down the computer.

  • Page 94

    Remove the following screws: (1) Four Torx T8M2.5×5.0 screws (2) Three Torx T8M2.5×6.0 screws (3) One Torx T8M2.0×5.0 screw. (4) One Torx T8M2.0×4.0 screw. Turn the computer right-side up, with the front toward you. Release the ZIF connector to which the card reader board cable is attached, and then disconnect the card reader board cable (1) from the system board.

  • Page 95

    Release the ZIF connector to which the fingerprint reader board cable is attached, and then disconnect the fingerprint reader board cable (3) from the system board. Lift the rear edge of the top cover (1), and then swing it up and forward until it rests at an angle. Lift the front edge of the top cover (2) until it disengages from the base enclosure.

  • Page 96: Card Reader Board

    Card reader board Description Card reader board (includes cable) Card reader board bracket Before removing the card reader board and bracket, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.

  • Page 97

    Remove the card reader board and bracket: Detach the card reader board cable (1) from the surface of the top cover (2). (The card reader board cable is attached to the top cover by double-sided tape.) Turn the top cover upside down, with the front toward you. Remove the two Phillips PM2.0×2.0 broad head screws (1) and the Phillips PM2.0×5.0 screw (2) that secure the card reader board bracket to the top cover.

  • Page 98

    Remove the card reader board bracket (4) by sliding it up and forward at an angle. Slide the card reader board (1) to the right until the tabs on the card reader board disengage from the slots on the top cover. Remove the card reader board (2) and cable.

  • Page 99: Speaker

    Reverse this procedure to install the card reader board, cable, and bracket. Speaker Description Speaker Before removing the speaker, follow these steps: Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. Disconnect all external devices connected to the computer.

  • Page 100: Bluetooth Module Cable

    Remove the speaker (4) from the base enclosure. Reverse this procedure to install the speaker. Bluetooth module cable NOTE: The Bluetooth module cable is included in the Cable Kit, spare part number 598766-001. Before removing the Bluetooth module cable, follow these steps: Shut down the computer.

  • Page 101

    Remove the Bluetooth module cable: Release the Bluetooth module cable (1) from the opening in the base enclosure. Disconnect the Bluetooth module cable (2) from the system board. Remove the Bluetooth module cable. Reverse this procedure to install the Bluetooth module cable. ENWW Component replacement procedures...

  • Page 102: System Board

    System board NOTE: The system board spare part kit includes the processor, replacement thermal material, and a replacement thermal material cleaning kit. Description System boards equipped with a standard-voltage (35-W) processor: Equipped with an Intel Core i7-620M 2.66-GHz processor for use in all countries and regions except the People's Republic of China and Russia Equipped with an Intel Core i7-620M 2.66-GHz processor for use only in the People's Republic of China and Russia...

  • Page 103

    Top cover (see Speaker (see When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ● SIM (see SIM on page ● Memory modules (see on page ●...

  • Page 104

    Remove the system board (4) from the base enclosure by sliding it up and to the left. Reverse this procedure to install the system board. Chapter 4 Removal and replacement procedures ENWW...

  • Page 105: Modem Module

    Modem module NOTE: The modem module spare part kit does not include a modem module cable. The modem module cable is included in the Cable Kit, spare part number 598766-001. Description For use in all countries and regions except Australia and New Zealand For use only in Australia and New Zealand Before removing the modem module, follow these steps: Shut down the computer.

  • Page 106: Fan/heat Sink Assembly

    Disconnect the modem module cable (3) from the modem module. Remove the modem module. Reverse this procedure to install the modem module. Fan/heat sink assembly Description For use only on computer models equipped with a standard-voltage (35-W) processor For use only on computer models equipped with a low-voltage (25-W) processor Before removing the fan/heat sink assembly, follow these steps: Shut down the computer.

  • Page 107

    Remove the battery (see Remove the following components: Memory module compartment cover (see Wireless module compartment cover (see Switch cover and keyboard (see Display assembly (see Top cover (see System board (see Remove the fan/heat sink assembly: Turn the system board upside down, with the front toward you. Disconnect the fan cable (1) from the system board.

  • Page 108

    NOTE: The thermal material must be thoroughly cleaned from the surfaces of the fan/heat sink assembly and system board each time the fan/heat sink assembly is removed. Thermal paste is located on the processor/Northbridge component (1) and the fan/heat sink assembly section that services it (2).

  • Page 109: Starting Computer Setup, Using Computer Setup, Navigating And Selecting In Computer Setup, Computer Setup

    Computer Setup Windows 7 Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your computer.

  • Page 110: Restoring Factory Settings In Computer Setup

    NOTE: You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to navigate and make selections in Computer Setup. Press to enter BIOS Setup. Select the File, Security, or System Configuration menu. To exit Computer Setup menus, choose one of the following methods: ●...

  • Page 111: Computer Setup Menus, File Menu

    Computer Setup menus The menu tables in this section provide an overview of Computer Setup options. NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your computer. File menu Select System Information Set System Date and Time System Diagnostics Restore defaults...

  • Page 112: Security Menu

    Reset/clear the fingerprint reader ownership (select models only; disabled by default). Enter, change, or delete a BIOS administrator password. Enroll or reset HP SpareKey, which is a set of security questions and answers used if you forget your password. Enable/disable Anti-Theft Protection.

  • Page 113: System Configuration Menu

    System Configuration menu NOTE: Some of the menu items listed in this section may not be supported by your computer. Select Language Boot Options Device Configurations ENWW To do this Change the Computer Setup language. ● Set a Startup Menu delay (in seconds). ●...

  • Page 114

    ● Enable/disable Preboot Authentication on HP QuickLook Boot (enabled by default). ● Enable/disable HP QuickWeb (enabled by default). ● Enable/disable HP QuickWeb Write Protect (disabled by default). ● Enable/disable Virtualization Technology (select models only; disabled by default). ● Enable/disable TXT (Intel Trusted Execution Technology) (select models only;...

  • Page 115

    Select Built-In Device Options ENWW To do this ● Enable/disable the wireless button state (enabled by default). ● Enable/disable embedded WLAN device radio (select models only; enabled by default). ● Enable/disable the embedded Bluetooth device radio (enabled by default). ● Enable/disable the Network Interface Controller (LAN) (enabled by default).

  • Page 116

    Select Port Options AMT Options Set Security Level Restore Security Defaults 108 Chapter 5 Computer Setup To do this NOTE: NOTE: All port options are enabled by default. ● Enable/disable the serial port. ● Enable/disable the parallel port. ● Enable/disable the flash media reader. ●...

  • Page 117: Using Computer Setup, Starting Computer Setup, Navigating And Selecting In Computer Setup, Windows Vista

    Windows Vista Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your computer.

  • Page 118

    Restoring factory settings in Computer Setup NOTE: Restoring defaults will not change the hard drive mode. To return all settings in Computer Setup to the values that were set at the factory, follow these steps: Turn on or restart the computer, and then press Menu”...

  • Page 119: File Menu, Computer Setup Menus

    Computer Setup menus The menu tables in this section provide an overview of Computer Setup options. NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your computer. File menu Select System Information Set System Date and Time System Diagnostics Restore defaults...

  • Page 120

    Reset/clear the fingerprint reader ownership (select models only; disabled by default). Enter, change, or delete a BIOS administrator password. Enroll or reset HP SpareKey, which is a set of security questions and answers used if you forget your password. Enable/disable Anti-Theft Protection.

  • Page 121

    System Configuration menu NOTE: Some of the menu items listed in this section may not be supported by your computer. Select Language Boot Options Device Configurations ENWW To do this Change the Computer Setup language. ● Set a Startup Menu delay (in seconds). ●...

  • Page 122

    ● Enable/disable Preboot Authentication on HP QuickLook Boot (enabled by default). ● Enable/disable HP QuickWeb (enabled by default). ● Enable/disable HP QuickWeb Write Protect (disabled by default). ● Enable/disable Virtualization Technology (select models only; disabled by default). ● Enable/disable TXT (Intel Trusted Execution Technology) (select models only;...

  • Page 123

    Select Built-In Device Options ENWW To do this ● Enable/disable the wireless button state (enabled by default). ● Enable/disable embedded WLAN device radio (select models only; enabled by default). ● Enable/disable the embedded Bluetooth device radio (enabled by default). ● Enable/disable the Network Interface Controller (LAN) (enabled by default).

  • Page 124

    Select Port Options AMT Options Set Security Level Restore Security Defaults 116 Chapter 5 Computer Setup To do this NOTE: NOTE: All port options are enabled by default. ● Enable/disable the serial port. ● Enable/disable the parallel port. ● Enable/disable the flash media reader. ●...

  • Page 125: Windows Xp, Starting Computer Setup, Using Computer Setup, Navigating And Selecting In Computer Setup

    Windows XP Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your computer.

  • Page 126

    To exit Computer Setup menus, choose one of the following methods: ● To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the screen, and then follow the on-screen instructions. – or – Use the key and the arrow keys to select File >...

  • Page 127

    Computer Setup menus The menu tables in this section provide an overview of Computer Setup options. NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your computer. File menu Select System Information Set System Date and Time System Diagnostics Restore defaults...

  • Page 128

    Reset/clear the fingerprint reader ownership (select models only; disabled by default). Enter, change, or delete a BIOS administrator password. Enroll or reset HP SpareKey, which is a set of security questions and answers used if you forget your password. Enable/disable Anti-Theft Protection.

  • Page 129

    System Configuration menu NOTE: Some of the menu items listed in this section may not be supported by your computer. Select Language Boot Options Device Configurations ENWW To do this Change the Computer Setup language. ● Set a Startup Menu delay (in seconds). ●...

  • Page 130

    ● Enable/disable Preboot Authentication on HP QuickLook Boot (enabled by default). ● Enable/disable HP QuickWeb (enabled by default). ● Enable/disable HP QuickWeb Write Protect (disabled by default). ● Enable/disable Virtualization Technology (select models only; disabled by default). ● Enable/disable TXT (Intel Trusted Execution Technology) (select models only;...

  • Page 131

    Select Built-In Device Options ENWW To do this ● Enable/disable the wireless button state (enabled by default). ● Enable/disable embedded WLAN device radio (select models only; enabled by default). ● Enable/disable the embedded Bluetooth device radio (enabled by default). ● Enable/disable the Network Interface Controller (LAN) (enabled by default).

  • Page 132

    Select Port Options AMT Options Set Security Level Restore Security Defaults 124 Chapter 5 Computer Setup To do this NOTE: NOTE: All port options are enabled by default. ● Enable/disable the serial port. ● Enable/disable the parallel port. ● Enable/disable the flash media reader. ●...

  • Page 133: Computer Specifications, Specifications

    Specifications Computer specifications Dimensions Depth Width Height (front to back) Weight Input power Operating voltage Operating current Temperature Operating (not writing to optical disc) Operating (writing to optical disc) Nonoperating Relative humidity Operating Nonoperating Maximum altitude (unpressurized) Operating (14.7 to 10.1 psia) Nonoperating (14.7 to 4.4 psia) Shock Operating...

  • Page 134: In Display Specifications

    Nonoperating NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this range of temperatures. 12.1-in display specifications Dimensions Width Depth Diagonal Number of colors Contrast ratio Brightness Backlight Character display Total power consumption Viewing angle 126 Chapter 6 Specifications Metric...

  • Page 135: Hard Drive Specifications

    Hard drive specifications Dimensions Height Width Weight Interface type Transfer rate Security Seek times (typical read, including setting) Single track Average Maximum Logical blocks Disk rotational speed Operating temperature *1 GB = 1 billion bytes when referring to hard drive storage capacity. Actual accessible capacity is less. Actual drive specifications may differ slightly.

  • Page 136: Dvd±rw And Cd-rw Supermulti Double-layer Drive Specifications

    DVD±RW and CD-RW SuperMulti Double-Layer Drive specifications Applicable disc Access time Random Cache buffer Data transfer rate 24X CD-ROM 8X DVD 24X CD-R 16X CD-RW 8X DVD+R 4X DVD+RW 8X DVD-R 4X DVD-RW 2.4X DVD+R(9) 5X DVD-RAM Transfer mode 128 Chapter 6 Specifications Read: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE...

  • Page 137: Dvd-rom Drive Specifications

    DVD-ROM Drive specifications Applicable disc Access time Random Cache buffer Data transfer rate 24X CD-ROM 8X DVD 24X CD-R 16X CD-RW ENWW Read: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video CD), Multisession CD (Photo-CD, CDEXTRA, Portfolio, CD-R, CD-RW), CDR, CD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-R,...

  • Page 138

    130 Chapter 6 Specifications ENWW...

  • Page 139: Windows 7, Backup And Recovery

    Recovering information using recovery tools NOTE: For detailed instructions, perform a search for these topics in Help and Support. NOTE: In case of system instability, HP recommends that you print the recovery procedures and save them for later use. ENWW Windows 7 131...

  • Page 140: Backing Up Your Information

    Backing up your information Recovery after a system failure is as complete as your most current backup. You should create system repair discs (select models only) and your initial backup immediately after software setup. As you add new software and data files, you should continue to back up your system on a regular basis to maintain a reasonably current backup.

  • Page 141: Performing A Recovery, Using The Windows Recovery Tools

    If possible, back up all personal files. If possible, check for the presence of the Windows partition or the HP Recovery partition. To check for the Windows partition, select Start > Computer.

  • Page 142: Using F11 Recovery Tools

    If the Windows partition and the HP Recovery partition are listed, restart the computer, and then press before the Windows operating system loads. Select Startup Repair. Follow the on-screen instructions. NOTE: For additional information on recovering information using the Windows tools, perform a search for these topics in Help and Support.

  • Page 143: Using A Windows 7 Operating System Dvd (purchased Separately)

    To order a Windows 7 operating system DVD, go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. You can also order the DVD by calling technical support. For contact information, refer to the Worldwide Telephone Numbers booklet included with the computer.

  • Page 144: Windows Vista, Backing Up Your Information

    NOTE: For detailed instructions, perform a search for these topics in Help and Support. NOTE: In case of system instability, HP recommends that you print the recovery procedures and save them for later use. Backing up your information Recovery after a system failure is as complete as your most current backup. You should create your initial backup immediately after software setup.

  • Page 145: Using The Windows Recovery Tools, Performing A Recovery

    The screen image is added to the document. Save the document. ● When backing up to discs, use any of the following types of discs (purchased separately): CD-R, CD-RW, DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD±RW. The discs you use will depend on the type of optical drive installed in your computer.

  • Page 146

    Recovery discs have been included for computers that do not have a partition. Use these discs to recover your operating system and software. To check for the presence of a recovery partition, select Start > Computer. If the partition is present, an HP Recovery drive is listed in the Hard Disk Drives section of the window.

  • Page 147: Using A Windows Vista Operating System Dvd (purchased Separately)

    (stored on discs or on an external drive) is easily accessible. To order a Windows Vista operating system DVD, go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. You can also order the DVD by calling technical support. For contact information, refer to the Worldwide Telephone Numbers booklet included with the computer.

  • Page 148

    NOTE: For detailed instructions, perform a search for these topics in Help and Support. NOTE: In case of system instability, HP recommends that you print the recovery procedures and save them for later use. Backing up your information Recovery after a system failure is as complete as your most current backup. You should create your initial backup immediately after software setup.

  • Page 149: Recovering Your Information, Performing A Recovery, Recovering The Operating System And Programs

    The recovery process reinstalls the original operating system as well as software and drivers. Software, drivers, and updates not installed by HP must be manually reinstalled. Personal files must be restored from a backup.

  • Page 150

    142 Chapter 7 Backup and recovery ENWW...

  • Page 151: Audio-in (microphone)/audio-out (headphone) Combo, Connector Pin Assignments

    Connector pin assignments 1394 Audio-in (microphone)/audio-out (headphone) combo ENWW Signal TPB- TPB+ TPA- TPA+ Signal Audio signal in (microphone) / audio out, left channel (headphone) Audio signal in (microphone) / audio out, right channel (headphone) Ground (microphone) / ground (headphone) 1394 143...

  • Page 152: Displayport

    DisplayPort 144 Chapter 8 Connector pin assignments Signal ML_lane 0 (positive) Ground Lane 0 (negative) Lane 1 (positive) Ground Lane 1 (negative) Lane 2 (positive) Ground Lane 2 (negative) Lane 3 (positive) Ground Lane 3 (negative) Connectecd to ground Connected to ground Auxiliary channel (positive) Ground Auxiliary channel...

  • Page 153: External Monitor

    External monitor ENWW Signal Red analog Green analog Blue analog Not connected Ground Ground analog Ground analog Ground analog +5 VDC Ground Monitor detect DDC 2B data Horizontal sync Vertical sync DDC 2B clock External monitor 145...

  • Page 154: Rj-11 (modem), Rj-45 (network)

    RJ-11 (modem) RJ-45 (network) 146 Chapter 8 Connector pin assignments Signal Unused Ring Unused Unused Unused Signal Transmit + Transmit - Receive + Unused Unused Receive - Unused Unused ENWW...

  • Page 155: Universal Serial Bus

    Universal Serial Bus ENWW Signal +5 VDC Data Data + Ground Universal Serial Bus 147...

  • Page 156

    148 Chapter 8 Connector pin assignments ENWW...

  • Page 157: Power Cord Set Requirements, Requirements For All Countries

    Power cord set requirements The wide-range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC, or from 220 to 240 volts AC The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased.

  • Page 158: Requirements For Specific Countries And Regions

    Requirements for specific countries and regions Country/region Australia Austria Belgium Canada Denmark Finland France Germany Italy Japan The Netherlands Norway The People's Republic of China South Korea Sweden Switzlerland Taiwan The United Kingdom The United States The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it will be used.

  • Page 159: Recycling, Battery, Display

    When you remove these components, handle them carefully. NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly that might require special handling at end-of-life. Disposal of mercury may be regulated because of environmental considerations. For disposal or recycling information, contact your local authorities, or see the Electronic Industries Alliance (EIA) Web site at http://www.eiai.org.

  • Page 160

    Perform the following steps: Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly.

  • Page 161

    Disconnect all display panel cables (1) from the display inverter and remove the inverter 2. Remove all screws (1) that secure the display panel assembly to the display enclosure. Remove the display panel assembly (2) from the display enclosure. Turn the display panel assembly upside down. Remove all screws that secure the display panel frame to the display panel.

  • Page 162

    Remove the display panel frame (2) from the display panel. Remove the screws (1) that secure the backlight cover to the display panel. Lift the top edge of the backlight cover (2) and swing it outward. Remove the backlight cover. Turn the display panel right-side up.

  • Page 163

    Remove the backlight cables (1) from the clip (2) in the display panel. Turn the display panel upside down. Remove the backlight frame from the display panel. WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. Remove the backlight from the backlight frame.

  • Page 164

    Disconnect the display cable (1) from the LCD panel. Remove the screws (2) that secure the LCD panel to the display rear panel. Release the LCD panel (3) from the display rear panel. Release the tape (4) that secures the LCD panel to the display rear panel. Remove the LCD panel.

  • Page 165: Index

    Index Symbols/Numerics 1394 port connector pinout 143 location 18 AC adapter, spare part numbers 34, 39 ambient light sensor board location 9 removal 81 spare part number 30, 37, 81 antenna disconnecting 59, 61 location 8 audio, product description 3 audio-in jack connector pinout 143 location 18...

  • Page 166

    display panel, product description 1 display release button 15 display specifications 126 DisplayPort connector pinout 144 docking connector 18 docking station, spare part number 34, 37 docking support, product description 4 drive light 15 drives, preventing damage 42 DVD-ROM Drive precautions 42 removal 63 spare part...

  • Page 167

    modem jack connector pinout 146 location 16 modem module product description 3 removal 97 spare part numbers 26, 35, 97 monitor port connector pinout 145 location 18 network jack connector pinout 146 location 17 numeric keypad keys 13 operating system, product description 5 optical drive location 16...

  • Page 168

    tools required 41 top cover removal 85 spare part numbers 25, 39, 85 TouchPad 14 TouchPad button 14 TouchPad on/off button 11, 14 TouchPad scroll zone 14 transporting guidelines 44 Universal Serial Bus (USB) port connector pinout 147 location 16, 17 vents 18, 19 video, product description 3 volume down button 11...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: