Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Grizzly G0620
- Page 1 DIGITAL CONTROLS Main Control Panel Fence Controller COPYRIGHT © MARCH, 2008 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #TR10571 PRINTED IN USA...
-
Page 3: Table Of Contents
INTRODUCTION ... 2 Foreword ... 2 Contact Info ... 2 MAIN CONTROL PANEL OPERATIONS ... 3 Control Panel Identification ... 3 Quick Start ... 4 MM/Inch Selection ... 5 Scoring Blade Adjustments ... 5 Blade Height Adjustments ... 6 Blade Tilt Adjustments ... 7 Rip Fence Adjustments ... -
Page 4: Introduction
Foreword Both controllers covered in this manual have capabilities beyond their use with the Model G0620. For that reason, you may find functions or features that will never be used with your saw. Aside from instructional clarity, this manual aims... -
Page 5: Main Control Panel Operations
Scoring Blade Height Key G. Number Keys H. Input Confirmation Key Millimeter/Inch Selection Key Start Key K. Stop Key G0620 Main Control Panel Figure 1. Control panel identification. Decimal Key M. Clear Key N. Function Confirmation Key O. Memory Set Key P. -
Page 6: Quick Start
Example: If your input is 2.15", then you would press the following keys: Press the Start move to where it is directed by your input. key at any time Indicator Light � � � numerical input. , and key and the component will G0620 Main Control Panel... -
Page 7: Mm/Inch Selection
� � Figure 4. Pressing mm/inch key to toggle the displayed unit of measure. G0620 Main Control Panel Scoring Blade Figure 5 shows the keys used to adjust the scor- ing blade, as discussed in this procedure. You can press the Stop key (Figure 4) the operation. -
Page 8: Blade Height Adjustments
, and the display would look � � height display. key. G0620 Main Control Panel... -
Page 9: Blade Tilt Adjustments
When finished, press the Stop indicator light stops shining. G0620 Main Control Panel Numerically Adjusting Blade Tilt You can enter a desired angle with the number keys and the blade will automatically adjust to that angle. -
Page 10: Rip Fence Adjustments
"OL" on the display. key. key and start over. , and the display would fence cutting width display. key. The control panel NOTICE G0620 Main Control Panel... -
Page 11: Combining Adjustment Entries
The indicator light on the blade height key no longer shines, but the numbers previously entered still flash. G0620 Main Control Panel Use the number keys to enter in the blade angle (Figure 13). ���� ����... -
Page 12: Memory Functions
Memory Functions The Model G0620 controller can store up to 29 different cut settings. Each cut setting will save positions for the blade height, blade angle, and rip fence cutting width. Saving Cut Settings Move the blade height, blade angle, and rip fence to the positions that you want to save. -
Page 13: Blade Diameter Calibration
Figure 21. Recalled dimensions flashing. Press the Start key. All components will move to their respective positions G0620 Main Control Panel Blade Diameter Calibration The exact dimensions of a blade can be pro- grammed into the control panel, so the blade height controls will not be skewed by blades of different sizes. -
Page 14: Blade Height Calibration
�������� until the display stops flashing. ������������ The indicator light stops shining to tell you that the control panel will no longer accept input for the blade height. key. �� �� � � blade height display. G0620 Main Control Panel... -
Page 15: Blade Tilt Calibration
The indicator light on the key shines to show that the control panel is ready to accept input. G0620 Main Control Panel Use the plus position the blade tilt so it fits flat against the 45° square while the 45° is flat against the table, as shown in Figure 25. -
Page 16: Rip Fence Cutting Width Calibration
For Example: If you measured 4.15", then you would press the following keys: Press and hold the input confirmation until the display stops flashing. The new set- ting now remains on the display. �������������� ����������������������� ����� ����� key. The indicator G0620 Main Control Panel... -
Page 17: Rip Fence Thickness Calibration
The calibration function can also be used if a sacrificial fence is attached to the standard rip fence. G0620 Main Control Panel To calibrate the rip fence thickness: Turn the control panel OFF. Push and hold the blade width keys, then turn ON the control panel. -
Page 18: Fence Operations
����� Figure 30. Control panel identification. *Diameter Function K. *Relative Measuring Mode Millimeter Unit Display Mode M. Inch Unit Display Mode N. Numeric Display O. Clear/Set Key P. ABS/REL Key Q. MM/Inch Key R. Function/Enter Key G0620 Main Control Panel... -
Page 19: Mm/Inch Selection
Figure 32. Current battery charge displayed. The display will automatically exit out of the battery charge screen after two seconds. G0620 Main Control Panel Changing Resolution The display can be adjusted to show a resolu- tion or accuracy from one to four decimal places, depending on which unit of measure is selected. -
Page 20: Calibrating The Display
������� ��� ��������� ��� ������� ������� � ��� ����� calibration. key to save the cur- � ����� key, then release it to key (the � ����� ��� ��� key. � ����� G0620 Main Control Panel ��� ��� key,... -
Page 21: Using Offsets
Block Figure 37. Second stop block engaged in origin block near fence extension. G0620 Main Control Panel Basically, the display shows the dimension of the second stop block because it adds a pre-pro- grammed offset distance from one origin block to the other. - Page 22 ORG number is selected. � keys to select the digit ������� key when it is blinking. ��� ��� key to save the cur- � ����� key. ��� ��� key. ��� ��� key, then � ����� key to cycle through G0620 Main Control Panel...
- Page 24 ��� ������ ��� ���� ���� ������� ����� ��� ������� ����� ��� �������� ��� ������� � � � ���� ����� ��� � � �������� ������ ��� � ����� ������ � �� ��� �������� ������� � ������ �������� ������ ������� ������ �� ����� ������...