Chamberlain Elite DC2000 Installation Manual

DC2000 Back-Up Wiring for the OmniControl™ Board

System Setup

"Manual"
setting: The DC2000 will respond to the input devices wired to the J 20 socket.
This mode can also be used as an emergency override. If 115 Vac power is on, but the system has an electronic
malfunction, the gate can be operated using the DC2000 system with input devices wired to J 20 socket.
"Auto"
setting: The DC2000 opens the gate automatically upon 115 Vac power failure and stays open. When
115 Vac power is restored, the gate operator will return to normal operation. (The gate can be closed by manual
command)
115 Vac Power 115 Vac Power On,
Failure OmniControl Board™ Malfunction
Manual Turn the 115 Vac power off then
Push and Hold to
Mode operate gate push and Hold to operate gate
Auto
Gate automatically Turn the 115 Vac power off then
Mode
opens gate opens automatically
If the DC2000 is automatically opening the gate
due to a power failure, any manual command
such as "Manual
Button", "Key
DO NOT wire
Sensor" will cancel the
115 Vac power
DC2000. After such cancellation, the DC2000
to the DC2000
will continue to operate in
115 Vac power is restored.
To Limit Switches
CHASSIS
GROUND
4
3
Factory installed
Cut and
Interlock Assembly
Discard Plug
Wires to J20 Socket
For Technical Support
and Ordering Parts:
1-800-528-2806

EMERGENCY

115 Vac Power On,
Emergency Override
If 115 Vac power is on, but the system has
Push and Hold to override
an electronic malfunction, the gate can be
the OmniControl™ Board
Push and Hold to override operated using the DC2000 system with
the OmniControl™ Board
ANY
"Optional Manual One-Button"
"Three Push
One-Button",
J 20
Switch", "Photocell" or "Edge
Socket
automatic mode of the
manual mode until
11 12 13
J5
J5
Radio Receiver +
13
12
11
Radio Receiver -
11
OVERRIDE
of these devices shown.
"Hold"
Push and to Open
"Hold"
Push again and to Close
Part # Part # AEXITP AEXITP
4 5
4
3
"Optional Three-Button"
3 4
N.O. Com
2 4
Com
N.O.
1 4
N.O. Com
"Hold"
Push and a Button to operate
DO NOT remove existing
wires from the audio alarm or
secondary protection sensor.
Red Wire
White Wire
Audio Alarm
Wires
Green and Purple wires
wrap behind board to
the limit switches
DC2000 Harness
with Optional Equipment

SAFETY OPTIONS

"Optional Edge Sensor"
"Optional Photocell Sensor" 12 VDC
OmniControl™ Board
Sensor Connection
Power Ground
4
6
Power +12 VDC
4
I n t
e r l
o c k
A s s
e m
b l y
W i
r e
"Optional Radio Receivers"
6
1 1
5
4
4
2
3
4
i v e r
11 1
e c e
13 2
i o R
3
11
R a d
4
12
Button One:
Normal Gate Operation Only
(OmniControl™ Board)
"Hold"
Push and DC2000 Remote Button to Open
"Hold"
Push again and DC2000 Remote Button to Close
AOMRON12V AOMRON12V
Part #
USE ONLY 12 VDC FAILSAFE PHOTOCELL
SENSORS FOR THIS SAFETY OPTION
Failsafe Photocell: If a photocell is not
working or loses power or photo beam is
blocked, then the photocell will stop all gate
operation.
"Optional Key Switch"
5
Part # Part # A1KX A1KX
Turn and "Hold" to Open
"Hold"
Turn again and to Close
Interlock
Assembly
Refer to Receiver
Manual for Further
Details about settings.
Part # Part # 312HM 312HM
Jumper P2:
to Constant (C)
Jumper P3:
to 12 Volt
Button Three:
Button One:
Optional Accessories
Normal Gate
Button Two:
Operation
Back-Up Operation
(OmniControl™ Board)
(DC2000)
Part # Part # 373LM 373LM