Table of Contents
Advertisement
Owner's Manual
Integrated High Definition
LCD Television
32DT1U
40FT1U
For an overview of steps for setting up your new TV, see page 10.
Note: To display a High Definition picture, the TV must be receiving
a High Definition signal (such as an over-the-air High Definition
TV broadcast, a High Definition digital cable program, or a High
Definition digital satellite program). For details, please contact
your TV antenna installer, cable provider, or satellite provider.
© 2010 TOSHIBA CORPORATION
All Rights Reserved
HIGH-DEFINITION TELEVISION
Owner's Record
The model number and serial number are on the back
of your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate
with your Toshiba dealer about this TV.
Model number:
Serial number:
HDA51F4010I
Advertisement
Table of Contents
Related Manuals for Toshiba 32DT1U
Summary of Contents for Toshiba 32DT1U
- Page 1 Owner’s Record The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. Model number: Serial number: HDA51F4010I...
-
Page 2: Safety Precautions
Dear Customer, Thank you for purchasing this Toshiba LCD TV. This manual will help you use the many exciting features of your new LCD TV. Before operating your LCD TV, please read this manual completely, and keep it nearby for future reference. -
Page 3: Important Safety Instructions
Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Page 4 Care For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions: 34) If you use the TV in a room whose temperature is 32 °F (0 °C) or below, the picture brightness may vary until the LCD warms up.
-
Page 5: Choosing A Location For Your Lcd Tv
This is normal, especially when the unit is being turned on or off. If these sounds become frequent or continuous, unplug the power cord and contact a Toshiba Authorized Service Center. DANGER: RISK OF SERIOUS PERSONAL INJURY OR DEATH! -
Page 6: Removing The Pedestal Stand
Removing the Pedestal Stand 1) Carefully lay the front of the unit face down on a flat, cushioned surface such as a quilt or blanket. Leave the stand protruding over the edge of the surface. Note: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel. -
Page 7: Trademark Information
FCC Declaration of Conformity Compliance Statement (Part 15): The Toshiba 32DT1U and 40FT1U Televisions comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The party responsible for compliance to these rules is: Toshiba America Consumer Products, L.L.C. 82 Totowa Rd. Wayne, NJ 07470. Ph: 1-800-631-3811 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. -
Page 8: Table Of Contents
Using the Surround feature ..48 Using the 7 Bands Equalizer feature ... 48 Chapter 8: Troubleshooting ...49 General troubleshooting ... 49 Chapter 9: Appendix ...51 Specifications ..51 Acceptable signal formats for PC IN and HDMI terminals ... 52 Limited United States Warranty for LCD Televisions ..53 Limited Canadian Warranty for Toshiba Brand Flat Panel Televisions ... 54 Digital Dynamic Range Control ® ..42 ® ® digital noise reduction ..47... -
Page 9: Chapter 1: Introduction
Chapter 1: Introduction Features of your new TV The following are just a few of the many exciting features of your new Toshiba widescreen, integrated HD, LCD TV: Integrated digital tuning (8VSB ATSC and • QAM) eliminates the need for a separate digital converter set-top box (in most cases). 1080p output resolution. • Two or Three HDMI ® digital, high-definition • multimedia interfaces 1080p input support ( page 16). One set of ColorStream HD high-resolution ® • component video inputs ( page 15). -
Page 10: Overview Of Steps For Installing, Setting Up, And Using Your New Tv
Place the TV far enough from walls and other • objects to allow proper ventilation. Inadequate ventilation may cause overheating, which will damage the TV. THIS TYPE OF DAMAGE IS NOT COVERED UNDER THE TOSHIBA WARRANTY. Do not plug in any power cords until AFTER you have connected all cables and devices to your TV. BEFORE connecting cables or devices to the TV, learn the functions of the TV’s connections and controls (... -
Page 11: Tv Front And Side Panel Controls And Connections
TV front and side panel controls and connections Model 32DT1U and 40FT1U are used in this manual for illustration purposes. Left side panel 32” 40” Control panel Control panel 1無 Green LED Power LED(Green) = Power indicator 2無 Remote sensor — Point the remote control toward this remote sensor. 3無 POWER — Press to turn the TV on and off. -
Page 12: Tv Back Panel Connections
ColorStream ® definition component video input (with standard stereo audio inputs) for connecting devices with component video output, such as a Toshiba DVD player with ColorStream Note: Component video cables carry only video information; separate audio cables are required for a complete connection. -
Page 13: Chapter 2: Connecting Your Tv
Standard A/V cables (red/white/yellow) Standard A/V cables (composite video) usually come in sets of three, and are for use with video devices with analog audio and composite video output. These cables (and the related inputs on your TV) are typically color- coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio. Component video cables (red/green/blue) Component video cables come in sets of three and are for use with video devices with component video output. (ColorStream ® is Toshiba’s brand of component video.) These cables are typically color-coded red, green, and blue. Separate audio cables are required for a complete connection. Note: Component video cables provide better picture performance than a standard (composite) video. HDMI cable ® (with HDMI Logo “ ”) HDMI (High-Definition Multimedia Interface) cable is for use with devices with an HDMI output. An... -
Page 14: Connecting A Vcr And Antenna Or Cable Tv
Chapter 2: Connecting your TV Connecting a VCR and antenna or Cable TV TV back panel You will need: Coaxial cables • Standard A/V cables • − If you have a mono VCR, connect L/MONO on the TV to your VCR’s audio out terminal using the white audio cable only. -
Page 15: Connecting A Dvd Player With Colorstream
Connecting a DVD player with ColorStream and a satellite receiver From satellite dish AUDIO COMPONENT VIDEO VIDEO Satellite S-VIDEO Satellite receiver with component video or DVD player with component video You will need: Coaxial cables • Standard A/V cables • − If you have a mono VCR, connect L/MONO on the TV to your VCR’s audio out terminal using the white audio cable only. -
Page 16: Connecting An Hdmi ® Or Dvi Device To The Hdmi Input
Chapter 2: Connecting your TV Connecting an HDMI or DVI ® device to the HDMI input The HDMI input on your TV receives digital audio and uncompressed digital video from an HDMI source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device. This input is designed to accept HDCP (High- Bandwidth Digital-Content Protection) program material in digital form from EIA/CEA-861-D– compliant consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output). The HDMI input can accept and display VGA, SVGA, XGA, WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz), 1080i (60Hz) and 1080p (24Hz/60Hz) signal formats. For detailed signal specifications, see page 52. Supported Audio format: Linear PCM, sampling rate 32/44.1/ 48 kHz Note: To connect a PC to the HDMI input, see page 18. To connect an HDMI device, you will need: One HDMI cable (type A connector) per HDMI device •... -
Page 17: Connecting A Digital Audio System
Connecting a digital audio system The TV’s DIGITAL AUDIO OUT terminal outputs a *Dolby ® Digital or 2-channel down-mixed PCM (pulse-code modulation) signal for use with an external Dolby Digital decoder or other external ® audio system with optical audio input. You will need: Optical audio cable (Use an optical audio cable • that has the larger “TosLink” connector and not the smaller “mini-optical” connector.) Dolby Digital decoder or other digital audio system TV back panel audio cable To control the audio: 1無 Turn on the TV and the digital audio device. - Page 18 Chapter 2: Connecting your TV feature ( “Using the PC settings feature” on page 43). Note: • The PC audio input terminals on the TV are shared with the HDMI-1 analog audio input terminals. • Some PC models cannot be connected to this TV. • An adapter is not needed for computers with a compatible mini D-sub15-pin terminal.
-
Page 19: Chapter 3: Using The Remote Control
Chapter 3: Using the remote control Installing the remote control batteries 1無 Sve the battery cover from the back of the remote control. Squeeze tab and lift cover. 2無 Install two “AAA” size batteries, making sure to match the + and – signs on the batteries to the signs on the battery compartment. 3無 Reinsert the battery cover in the remote control until the tab snaps. Caution: Batteries must not be exposed to excessive heat such as sunshine, fire or the like. Note: •... -
Page 20: Learning About The Remote Control
Chapter 3: Using the remote control Learning about the remote control The buttons used for operating the TV only are described here. Note: The error message “NOT AVAILABLE” may appear if you press a key for a function that is not available. 1無 POWER turns the TV on and off. When the TV is on, the green LED indicator on the TV front will be illuminated. 2無 PIC SIZE cycles through the picture sizes: Natural , TheaterWide 1/2/3 , Full , 4:3 HD , Native and Dot by Dot ( ... -
Page 21: Chapter 4: Menu Layout And Navigation
Chapter 4: Menu layout and navigation Main menu layout The tables below and on the next page provide a quick overview of your TV’s menu system. To open the main menus (illustrated below), press Icon Item Mode Picture Picture Settings Noise Reduction Game Mode Theater Settings Digital Audio Selector Sound Audio Settings Advanced Audio Settings Audio Setup CC Selector Preferences Base CC Mode Digital CC Settings Input Labeling Channel Labeling Menu Language Channel Browser Setup Enable Rating Blocking Locks Edit Rating Limits Input Lock Control Panel Lock GameTimer New PIN Code Installation Setup Sleep Timer PC Settings... -
Page 22: Setup/Installation Menu Layout
Chapter 4: Menu layout and navigation Setup/Installation menu layout The Installation menu contains the Terrestrial and System Status menus. To open the Installation menu (illustrated below), press Setup menu, select Installation, and press Icon Item Input Configuration Terrestrial Channel Program Channel Options Channel Tuning Mode Time Zone Signal Meter System Status System Information Navigating the menu system You can use the buttons on the remote control or TV control panel to access and navigate your TV’s on- screen menu system. Press to open the menu system. • When a menu is open, use the up/down/left/right • arrow buttons (pqtu) on the remote control or TV control panel to move in the corresponding direction in the menu. -
Page 23: Chapter 5: Setting Up Your Tv
Chapter 5: Setting up your TV Initial Setup When you first turn on or reset the TV, the Initial Setup window will appear. 1無 In the Menu Language field, press t or u to select your preferred language. 2無 Press t or u to select Time Zone Setup and set your desired time zone with t or u and press 3無 Next, the Location setting window will appear.For normal home use, press t or u to select Home and press 4無 Next, ANT/CABLE In setup window will appear. Press t or u to select the input source (Cable or Antenna) for the ANT/CABLE input on the TV. 5無 If you select Antenna, the Channel Tuning Mode setup window will appear. To tune only digital channels, select Digital. To tune digital channels preferentially over analog when entering channel number directly, select Auto. For normal tuning, select Standard. Press to continue to Auto... -
Page 24: Programming Channels Into The Tv's Channel Memory
Programming channels into the TV’s channel memory When you press or on the remote control or TV control panel, your TV will stop only on the channels you programmed into the TV’s channel memory. Follow the steps below to program channels into the TV’s channel memory. Programming channels automatically Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels in the channel memory. Note: • You must configure the ANT/CABLE input source before programming channels ( page 23). • The automatic channel programming process will erase channels that were previously programmed into the TV’s memory. -
Page 25: Labeling Channels
To add a channel to the channel memory: Highlight the checked box next to the channel number you want to add, and then press to remove the tick. To manually add digital subchannels on a physical channel: Use the Channel Numbers and the Dash ( the remote control to enter the channel number (for example, 56–1). If the channel is found, the number will be added to the list and the box will be unchecked. If the channel is not found, a message will appear. Note: Skipped channels cannot be selected with ; however, they can still be accessed using the number keys on the remote control. -
Page 26: Setting The Hdmi ® Audio Mode
To delete the custom label: 1無 Open the Channel Labeling window. 2無 Highlight the label to be deleted and press 3無 Highlight Yes from the deletion confirmation window and press 4無 Highlight Done and press to save changes, and go back to the Channel Labeling window. Setting the HDMI audio mode ® To set the HDMI audio mode: 1無 Press and open the Sound menu. 2無 Highlight Audio Setup and press 3無 Press p or q to select HDMI 1 Audio and then press t or u to select the HDMI 1 audio mode (Auto, Digital, or Analog). (Auto is the recommended mode.) See “Connecting an HDMI... -
Page 27: Setting The Time Zone
Setting the time zone The Time Zone setup will allow you to specify the correct time zone for your region. This feature will allow the TV status information to show the correct time zone information ( page 46). To set the time zone: 1無 From the Setup menu, highlight Installation and press . A new set of Installation menu icons will appear. 2無 Highlight Time Zone, and press 3無 Press t or u to select the region, highlight Done, and then press After the time zone has been set, you will be asked to set the current Daylight Saving Time status. To set the Daylight Saving Time status: 1無 Press t or u to select Yes or No, highlight Done, and then press Viewing the system status To view the system status: 1無... -
Page 28: Chapter 6: Using The Tv's Features
Chapter 6: Using the TV’s features Selecting the video input source to view To select the video input source to view: 1無 Press on the remote control or TV control panel. 2無 And then either: a) Press 0–6 or 7; or b) Repeatedly press pq on the remote control and then press to change the input; or c) Repeatedly press on the remote control or TV control panel to change the input. The current signal source displays in the top right corner of the Input Selection screen. 32” 40”... -
Page 29: Tuning Channels
Chapter 6: Using the TV’s features Input labeling example: The screen below left shows the default Input Selection screen (with none of the inputs labeled as a specific device). The screen below right is an example of how you could label the inputs if you connected a VCR to VIDEO , a video recorder to ColorStream HD, a DTV set-top box to HDMI 1, and a satellite/DSS set-top box to HDMI 2, and a DVD player to HDMI 3 (only for 40”). For 32” Input Selection ANT/CABLE ANT/CABLE 1 Video ColorStream HD HDMI 1 HDMI 2 5 PC 6 USB Media INPUT to Select Navigate Input Selection screen Input Selection screen with no inputs labeled. -
Page 30: Elements Of The Channel Browser
Chapter 6: Using the TV’s features press t or u to select On or Off. 5無 Press q to highlight Inputs List, and then press t or u to select On or Off. 6無 Press q to highlight Favorites List, then press t or u to select On or Off. 7無 To save your entries, highlight Done and press . To return to factory defaults, highlight Reset and press To open the Channel Browser™: Press t or u on the remote control. • Press t to surf backward through the previously • tuned 32 channels in the History list, the channels in the ANT/ CABLE channel list, the inputs in the Inputs list or the favorite channels/inputs in the Favorites list. Press u to surf forward through the channel • History, the ANT/CABLE channel list, the Inputs list or the favorite channels/inputs in the Favorites list. -
Page 31: Setting The Channel Tuning Mode
Chapter 6: Using the TV’s features All channels that are tuned using • remote control. Note: Whenever an item is selected that cannot be tuned (for various reasons), the TV will automatically tune to the previously viewed channel or input. Clearing channels from the History List: Reconfiguring the ANT/CABLE input will clear the •... -
Page 32: Switching Between Two Channels Using Surflock
Chapter 6: Using the TV’s features 3無 Press on the remote control. The previous channel will display. Each time you press TV will switch back and forth between the last two channels that were tuned. Note: If you press from a non-antenna input, the TV will return to the last-viewed input. Switching between two channels using SurfLock™ The SurfLock™ feature temporarily “memorizes” one channel to the button, so you can return to that channel quickly from any other channel by pressing . To memorize a channel to the 1無 Tune the TV to the channel you want to program into the button. - Page 33 Chapter 6: Using the TV’s features Picture Size TheaterWide 2 (for letter box programs) A B C D E F G - - - - - - - - - - - - - - - - The top and bottom edges of the picture may be hidden*. TheaterWide 3 (for letter box programs with subtitles) A B C D E F G - - - - - - - - - - - - - - - -...
-
Page 34: Scrolling The Theaterwide ® Picture (Theaterwide 2 And 3 Only)
Chapter 6: Using the TV’s features Scrolling the TheaterWide (TheaterWide 2 and 3 only) You can set separate scroll settings for the TheaterWide 2 and TheaterWide 3 modes for each input. To set the scroll settings: 1無 Press and open the Picture menu. 2無 Highlight Theater Settings and press 3無 In the Picture Size field, select either TheaterWide 2 or TheaterWide 3 (you cannot scroll in any other mode). 4無 Press q to highlight the Picture Scroll field. 5無 Press t or u to scroll the picture up and down as needed. 6無 To save the new settings, highlight Done and press . To revert to the factory defaults, highlight Reset and press... -
Page 35: Using The Freeze Feature
Chapter 6: Using the TV’s features Using the FREEZE feature To use the FREEZE feature: 1無 When viewing the TV, press picture a still picture. 2無 To return to the moving picture, press again (or any other button). Note: If the TV is left in FREEZE mode for more than 15 minutes, the FREEZE mode will automatically be released and the TV will return to moving picture. -
Page 36: Using The Closed Caption Mode
Chapter 6: Using the TV’s features To adjust the picture quality: 1無 Press and open the Picture menu. 2無 Highlight Picture Settings and press 3無 Press p or q to select the picture quality you want to adjust (Contrast, Backlight, DynaLight, Brightness, Color, Tint, or Sharpness), and then press t or u to adjust the setting, as described in the table above. 4無 To save the new settings, highlight Done and press . You can use any of the picture modes ( “Selecting the picture mode”) as a starting point for adjusting the picture settings. To revert back to the base mode that you began adjusting the picture settings from, highlight Reset and press The picture qualities you adjusted are automatically saved in the Preference mode ( “Selecting the picture mode”) until Reset is selected. Using the closed caption mode Base closed captions The closed caption mode has two options: Captions—An on-screen display of the dialogue,... -
Page 37: Cc Selector
Chapter 6: Using the TV’s features Caption Size Auto, Small, Standard, Large Auto, Default, Mono w. Serif, Caption Text Prop. w. Serif, Mono w/o Type Serif, Prop. w/o Serif, Casual, Cursive, Small Capitals Auto, None, Raised, Caption Text Depressed, Uniform, Left Edge Drop Shadow, Right Drop shadow Auto, Black, White, Red, Caption Text Green, Blue, Yellow, Magenta, Color Cyan Text Foreground Auto, Transparent, Opacity Translucent, Flashing, Solid Auto, Black, White, Red, Background Green, Blue, Yellow, Magenta, Color Cyan Text Background Auto, Transparent, Opacity Translucent, Flashing, Solid Auto, Black, White, Red, Caption Text Green, Blue, Yellow, Magenta, Edge Color Cyan... -
Page 38: Selecting Stereo/Sap Broadcasts
Chapter 6: Using the TV’s features Selecting stereo/SAP broadcasts The multi-channel TV sound (MTS) feature allows you to output high-fidelity stereo sound. MTS also can transmit a second audio program (SAP) containing a second language, music, or other audio information (when provided by individual stations). When the TV receives a stereo or SAP broadcast, the word “STEREO” or “SAP” appears on-screen when is pressed.The MTS feature is only available for analog signals on the ANT/CABLE input. To listen to stereo sound: 1無 Press and open the Sound menu. 2無 Highlight Audio Setup and press 3無 In the MTS field, select Stereo. 4無 To save the new settings, highlight Done and press To reset the settings to the factory defaults, highlight Reset and press Note: • You can typically leave the TV in Stereo mode because it will automatically output the type of sound being broadcast (stereo or monaural). -
Page 39: Using The Locks Menu
Chapter 6: Using the TV’s features To use the Dolby Digital Dynamic Range Control: 1無 Press and open the Sound menu. 2無 Highlight Audio Setup and press 3無 In the Dolby Digital Dynamic Range Control field, select Compressed. When Standard is selected, the audio is output with minimal compression. 4無 To save the new settings, highlight Done and press To revert to the factory defaults, highlight Reset and press Note: • This item will be grayed out for NTSC signals, Video, ColorStream, HDMI, PC and USB Media inputs. -
Page 40: Downloading An Additional Rating System For Blocking Tv Programs And Movies
• The additional rating system is not designed, transmitted, or controlled by the TV or Toshiba, nor is the availability of an additional rating system determined or controlled by Toshiba. Similarly, the rating of programs in an additional rating system is not determined, transmitted, or controlled by the TV or Toshiba. -
Page 41: Locking Channels
Chapter 6: Using the TV’s features Independent rating system for broadcasters Ratings Description and Content themes Mature Audience Only (This program is specifically designed to be viewed by adults and therefore may be unsuitable for TV-MA children under 17.) L) Crude or indecent language S) Explicit sexual activity V) Graphic violence Parents Strongly Cautioned (This program contains some material that many parents would find unsuitable for children under 14 TV-14 years of age.) D) Intensely suggestive dialog L) Strong, coarse language S) Intense sexual situations V) Intense violence Parental Guidance Suggested (This program contains material parents may find unsuitable for younger children.) TV-PG D) Some suggestive dialog L) Infrequent coarse language S) Some sexual situations V) -
Page 42: Unlocking Programs Temporarily
Chapter 6: Using the TV’s features Unlocking programs temporarily If you try to tune the TV to a program that exceeds the rating limits you set, the TV will enter program lock mode and the following message will appear on- screen: This program exceeds the rating limit you set. Push 'MUTE' to enter PIN. You can either temporarily unlock the program or select an unlocked program to watch. To temporarily unlock the program: 1無 Press 2無 Enter your four-digit PIN code and press the correct code is entered, the program lock mode is released and the normal picture appears. All locking is disabled until the TV is turned off, and will be enabled when the TV is turned on again. Using the input lock feature You can use the Input Lock feature to lock the video inputs (VIDEO, ColorStream HD, HDMI 1, HDMI 2, HDMI 3 (only for 40”), PC, and USB Media) and channels 3 and 4. You will not be able to view the input sources or channels until you unlock the inputs. -
Page 43: Using The Pc Settings Feature
Chapter 6: Using the TV’s features 5無 Press u to select On. When the control panel is locked and any button on the control panel (except POWER) is pressed, the message “NOT AVAILABLE” appears. To unlock the control panel: Select Off in step 5 above, or press and hold the VOLUME – button on the TV control panel for about 10 seconds until the volume icon appears. Using the PC settings feature You can view an image from a PC on the TV screen. When a PC is connected to the TV's PC IN terminal, you can use the PC Settings feature to make adjustments to the image. If the edges of the picture are cut off, readjust the Horizontal Position and Vertical Position. If the picture is affected by interference, readjust the Clock Phase and Sampling Clock. To adjust the PC settings: 1無... -
Page 44: Using The Usb Media
• Do not use a USB Hub. • You must obtain any required permission from copyright owners to use copyright content. Toshiba cannot and does not grant such permission. • Depending on the file size and amount in your USB storage device, it may take some time for loading to view. -
Page 45: Slideshow
Chapter 6: Using the TV’s features Slideshow This view allows you to watch a slideshow of the photos. In this mode, only files located in the selected directory will be played. 1無 into Photo Browser, and choose the file Press to open the Slideshow function. 2無 Press t / u to view the previous/next photo. To set Interval, Effect and Repeat settings: 1無 to open the USB Media Settings. Press 2無 Press p or q to select Slideshow Interval, Slideshow Effect or Slideshow Repeat. 3無 Press t or u to adjust the setting and press To close the Photo Viewer 1無... -
Page 46: Setting The Sleep Timer
Chapter 6: Using the TV’s features Setting the sleep timer You can set the sleep timer to turn off the TV after a set length of time (maximum of 180 minutes). To set the sleep timer using the remote control: Press on the remote control to set the length of time until the TV turns off. Repeatedly press increase the time in 10-minute increments, or press p or q to increase or decrease the time in 10-minute increments, to a maximum of 180 minutes. To set the sleep timer using the on-screen menus: 1無 Press and open the Setup menu. 2無 Highlight Sleep Timer and press 3無... -
Page 47: Chapter 7: Using The Tv's Advanced Features
Chapter 7: Using the TV’s advanced features Using the advanced picture settings features Using Dynamic Contrast Dynamic Contrast detects changes in picture quality that affect the appearance of your contrast settings and then automatically adjusts the video. To select Dynamic Contrast preference: 1無 From the Picture menu, highlight Picture Settings and press 2無 Highlight Advanced Picture Settings and press 3無 Press p or q to select Dynamic Contrast. 4無 Press t or u to select On and Off. Using the static gamma feature The static gamma feature allows you to adjust the levels of black in the picture. -
Page 48: Using Mpeg Noise Reduction
Chapter 7: Using the TV’s advanced features the menu will display the text “CableClear” . The available selections are Off, Low, Middle, and High. • If the current input is ColorStream HD, HDMI 1, HDMI 2 or HDMI 3(only for 40”), the menu will display the text “DNR.”... -
Page 49: Chapter 8: Troubleshooting
Chapter 8: Troubleshooting General troubleshooting Before calling a service technician, please check this chapter for a possible cause of the problem and some solutions you can try. Black box on-screen The closed caption feature is set to one of the Text • modes (T1, T2, T3, or T4). Set the closed caption feature to Off ( page 36). TV stops responding to controls If the TV stops responding to the controls on • the remote control or TV control panel and you cannot turn off the TV, please unplug the power cord few seconds then re-plug to try again. Other problems If your TV’s problem is not addressed in this • Troubleshooting section or the recommended solution has not worked, use the Restore Factory Defaults procedure ( page 27). TV will not turn on Make sure the power cord is plugged in, and then • press The remote control batteries may be dead. -
Page 50: Sound Problems
Sound problems Check the antenna/cable connections ( Chapter 2). • The station may have broadcast difficulties. Try • another channel. The sound may be muted. Press VOLUME. • Make sure the Speakers setting is On in Audio • Settings menu. If you hear no sound, try setting the MTS feature • to Stereo mode ( page 38). If you are not receiving a second audio program • from a known SAP source, make sure the MTS feature is set to SAP mode ( page 38). If you hear audio that seems “incorrect” for the • program you are watching (such as music or a foreign language), the SAP mode may be on. Set the MTS feature to Stereo mode ( page 38). Remote control problems Remove all obstructions between the remote • control and the TV. The remote control batteries may be dead. • Replace the batteries ( page 19). If the TV still does not act as expected, use the • Reset Factory Defaults procedure ( page 27). Channel tuning problems • The channel may have been erased from the channel memory by the Programming channels automatically feature. Add the channel to the... -
Page 51: Chapter 9: Appendix
Television System NTSC standard ATSC standard (8VSB) Digital Cable (64 QAM, 256 QAM) Channel Coverage VHF: 2 through 13 UHF: 14 through 69 Cable TV: Mid band (A-8 through A-1, A through I) Super band (J through W) Hyper band (AA through ZZ, AAA, BBB) Ultra band (65 through 94, 100 through 135) Power Source: 120 V AC, 60 Hz Power Maximum Current 32DT1U: 1.55 A 40FT1U: 2.65 A Power Consumption 32DT1U:0.6 W in standby mode 40FT1U: 0.6 W in standby mode Audio Power: 32DT1U: 7 W + 7 W 40FT1U: 7 W + 7 W Speaker Type: Two 1-5/8 × 6 inches (4 × 15.2 cm) Video/Audio Terminals VIDEO/AUDIO INPUT: VIDEO: 1 V(p-p), 75 ohm, negative sync. AUDIO: 150 mV(rms) (30% modulation equivalent, 22 k ohm or greater) ColorStream (component video) HD INPUT: ®... -
Page 52: Acceptable Signal Formats For Pc In And Hdmi Terminals
Acceptable signal formats for PC IN and HDMI terminals PC IN signal formats Note: Depending on the connected PC, the following status may occur; incorrect display, false format detection, picture position failure, blur, or judder. But this is not a malfunction of your TV. Format Resolution V. -
Page 53: Limited United States Warranty For Lcd Televisions
Limited United States Warranty for LCD Televisions Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original consumers in the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS LCD TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE. -
Page 54: Limited Canadian Warranty For Toshiba Brand Flat Panel Televisions
OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. THEREFORE, THE ABOVE PROVISIONS MAY NOT APPLY TO YOU UNDER SUCH CIRCUMSTANCES. Limited Canadian Warranty Toshiba Brand Flat Panel Televisions Toshiba of Canada Limited (“TCL”) makes the following limited warranties to original consumers in Canada. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS TOSHIBA BRAND FLAT PANEL TELEVISION (the “TELEVISION(S)”... - Page 55 SUPERCEDES AND SPECIFICALLY DISCLAIMS ANY OTHER WARRANTY, CONDITION OR REPRESENTATION NOT STATED IN THIS WARRANTY, WHETHER MADE BY TCL, TOSHIBA CORPORATION, THEIR AFFILIATES, ADRs AND ASPs AND WHETHER MADE ORALLY OR IN WRITING (INCLUDING ANY STATEMENT IN ANY BROCHURE, PRESS RELEASE, ANNOUNCEMENT, ADVERTISEMENT, POINT OF SALE DISPLAY, ETC.).
- Page 56 Chapter 9: Appendix shall be and remain valid and enforceable. If and to the extent that any provision of this limited warranty as it relates to any of the Related Parties is found to be invalid or unenforceable in respect of that party (the “Excluded Party”), the Excluded Party shall be deemed to be severed or excluded from the provision, and the provision shall remain valid, enforceable and applicable in respect of the other or remaining Related Parties. To the extent permitted by law, this limited warranty shall be governed and construed in accordance with the laws of Ontario. If there is any inconsistency between this limited warranty, on the one hand, and any statement in the packaging of the Television or in any other document enclosed with, or used in the context of the promotion or sale of, the Television, on the other hand, the provisions of this limited warranty shall prevail. How to Obtain Warranty Services If, after following all of the operating instructions in this manual, checked the “Troubleshooting” section, and have visited www.toshiba.ca/support for additional information, you find that service is needed, please contact TCL Customer Support toll free at 1 800 268- 3404.
- Page 57 Notes...
- Page 58 TOSHIBA AMERICA CONSUMER PRODUCTS, L.L.C. Corporate Headquarters: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A. NATIONAL SERVICE DIVISION: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A. TOSHIBA OF CANADA LTD. HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA – TEL: (905) 470-5400 SERVICE CENTERS: TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA – TEL: (905) 470- 5400 MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J 4A1, CANADA – TEL: (514) 390-7766 VANCOUVER: 6932 GREENWOOD STREET, BURNABY, B.C., V5A 1X8, CANADA – TEL: (604) 303-2500 CableClear, ColorStream, GameTimer, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C. Channel Browser, DynaLight, and SurfLock are trademarks of Toshiba America Consumer Products, L.L.C. PRINTED IN CHINA...