Page 1
Philips Hospitality LCD TV: Pro range EN 19HFL3340D/10 Please ask your local sales support for additional information on correct installation/ positioning of the TV in the room and complementary accessories. PHILIPS DFU-AUG2008 PB1 ...
Page 3
No components are user- serviceable. Do not open or remove covers to the inside of the product. Repairs may only be done by Philips Service Centres and official repair shops. Failure to do so shall void any warranty, stated or implied.
Important Congratulations on your purchase and welcome to Philips! Read this user manual before you start to use this product. Pay close attention to this section and follow the safety and screen care instructions. The product warranty does not apply if damage is caused by failing to follow these instructions.
Power consumption The TV consumes minimal energy in standby mode to minimise environmental impact. Active power consumption is displayed at the back of the TV. For more product specifications, see the product leaflet at www.philips.com/support.
Your TV This section gives you an overview of commonly-used TV controls and functions. 2�1 TV overview Side controls and indicators POWER PROGRAM +/- MENU VOLUME +/- Power indicator/remote control sensor Side connectors VOLUME Use the TV side connectors to connect to MENU mobile devices such as a high-definition camcorder or game console.
Page 7
Remote control ALARM Û SLEEP EN-6 ALARM Û For advanced information about the remote control, see Section 5.1 Remote control overview. Power GUIDE TELETEXT Colour keys From left, red, green, yellow, blue , Æ, Î, ï, OK Í Navigation or cursor keys MENU P +/- Program up or down...
3�2 Wall mount the TV WARNING Wall mounting of the TV should only be performed by qualified installers. Koninklijke Philips Electronics N�V� bears no responsibility for improper mounting that results in accident or injury� Step 1 Purchase a wall bracket...
Page 9
Firmly pull the stand from the bottom of the TV. Place both the stand and bolts in a secure location for future reinstallation. Step 3 Connect cables Connect the antenna cable, mains cord and all other devices to the back of the TV as described in the following sections.
3�3 Connect the antenna cable Locate the TV ANTENNA connector at the back of the TV. Connect one end of an antenna cable (not supplied) to the TV ANTENNA connector. Use an adaptor if the antenna cable does not fit. Connect the other end of the antenna cable to your antenna outlet, ensuring that the cable is tightly secured at both ends.
3�5 Manage cables Route your mains cord, antenna cable and all other device cables through the cable holder (1) at the back of the TV. 3�6 Insert the remote control batteries Slide the battery cover off the back of the remote control.
Use your TV This section helps you perform basic TV operations. Instructions on advanced TV operations are provided in Section 5 Use more of your TV. 4�1 Switch your TV on/off or to standby Switch on your TV • If the power indicator (1) is off, press POWER on the side of the TV.
4�2 Watch TV Switch channels Press a number (1 to 999) or press on your remote control. Press PROGRAM +/- on the side controls of the TV. Press ∏ Select a picture format.. Adjust volume Press ” + or - on the remote control, or Press VOLUME + or - on the side controls of your TV.
4�4 Use teletext Press TELETEXT on the remote control. The main index page appears. ALARM Û • To select a page with the remote control: • Enter the page number with the number keys. • Press P +/- or Î ï to view the next or previous page.
Use more of your TV 5�1 Remote control overview ALARM Û Switches the TV on from standby or back to standby. GUIDE Toggles the Electronic Program Guide on or off Only active with digital channels. SOURCE Selects connected devices. EN-14 SUBTITLE Activates or deactivates subtitles.
SLEEP Press MENU on the remote control to display the TV menu. TV Menu Smart settings Picture Sound Features PHILIPS Install Press ï to select Picture. TV Menu Smart settings Picture Sound Features Install SLEEP...
Page 17
Æ to enter the Brightness setting. Brightness Press Î or ï to adjust the setting. Press Í to return to the Picture settings or press MENU to exit. Note More choices are available when digital channels are installed and broadcast. EN-16 PHILIPS PHILIPS...
OFF to disable this function Use smart settings Apart from manually adjusting picture settings, you can use Smart settings to set your TV to a predefined picture and sound setting. PHILIPS Press MENU on the remote control and select Smart settings. Press Æ...
Page 19
Change picture format Change the picture format to suit your content. Press ∏ (PICTURE FORMAT) on your remote control. Alternatively, press MENU and select Picture > Picture format. Press Î or ï to select one of the following picture formats: •...
• Auto volume leveling: Reduces sudden volume changes, for example, during commercials or when switching from one channel to another. Select On or Off. PHILIPS 5�4 Change to Shop or Home mode Press MENU on the remote control and select Install >...
5�5 Use advanced teletext features Your TV has a 100 page memory that stores broadcasted teletext pages and subpages. Select teletext subpages A teletext page can hold several subpages. Subpages are displayed on a bar next to the main page number. Press TELETEXT on the remote control.
Ainsley Harriott. Simmer and enjoy. Prev Page Next Page Return Press GUIDE to exit the EPG. 5�7 Adjust feature settings Press MENU on the remote control and select Features� PHILIPS Press Æ to enter. TV settings Smart settings Picture Sound Features Install Filter Press Î...
Automatically switch the TV to standby (Sleeptimer) Sleeptimer switches the TV to standby after a defined period of time. Press MENU on the remote control and select Features > Timer > Sleeptimer. Press Æ to enter the Sleeptimer menu Press Î...
Install menu is temporarily overruled. Press MENU on the remote control and select Features > Subtitle Language. Press Æ to enter the list of available languages. Press Î or ï to select a subtitle language. Press PHILIPS EN-23...
5�9 Listen to digital radio channels If digital broadcasting is available, digital radio channels are installed automatically during installation. To reorder the digital radio channels, see Section 6.3 Rearrange the channels. Press OK on the remote control. The All channels menu is displayed. Use the number keys to select a radio channel.
• Preferred audio format format for the best sound reproduction: - If you have connected a home theater system, select Advanced. PHILIPS - Otherwise, select Standard. Note Do not select Advanced unless you have connected a home theatre system. If you select Advanced, you must set other options.
Analogue: manual installation > Fine tune. Press Æ to enter the Fine tune menu. Press Î or ï to adjust the frequency. PHILIPS Press Í when done. Select Store current channel to store the fine tuned channel under the current channel number.
6�3 Rearrange channels Press MENU on the remote control and select Install > Channel installation > Rearrange. Press Æ to enter the Rearrange list. Press Î or ï to select the channel you want to rearrange. Press the yellow key to move the channel up the list, or press the blue key to move the channel down the list.
6�7 Test digital reception If using digital broadcasts, you can check the quality and signal strength of digital channels. This allows you to reposition and test your antenna or satellite dish. Press MENU on the remote control and select Install > Channel installation > Digital: Test reception.
Connect devices 7�1 Connection overview IR LINK EXT 3 Back connectors EXT 1 : First SCART connector for DVD players, VCRs, digital receivers, game consoles and other SCART devices. Supports Audio L/R, CVBS in/out, RGB. EXT 3 : Component video (Y Pb Pr) and Audio L/R input connectors for DVD players, digital receivers, game consoles and other component video devices.
TV and HDMI devices. You must use HDMI to experience full high-definition video. You must also use HDMI cables to enable Philips EasyLink as described in Section 7.5 Use Philips EasyLink. D Note Philips HDMI supports HDCP (High- bandwidth Digital Contents Protection).
Page 32
Composite - Basic quality Composite video provides basic analogue connectivity, usually combining a (yellow) video cinch cable with (red and white) Audio L/R cinch cable. Match the cable colours when connecting to the composite Video and Audio L/R input connectors on the side of the TV. Composite audio/video cable - Yellow, red and white EN-31...
7�3 Connect devices This section describes how to connect various devices with different connectors and supplements examples provided in the Quick Start Guide. Caution Disconnect the mains cord before connecting devices. Note Different types of connectors may be used to connect a device to your TV, depending on availability and your needs.
Satellite receiver To receive analogue channels via antenna and digital channels via a satellite receiver, connect an antenna cable and SCART cable as illustrated: IR LINK EXT 3 Satellite receiver HD digital receiver To receive analogue channels via antenna and digital channels via a HD digital receiver, connect two antenna cables and HDMI cable as illustrated: IR LINK HDMI...
Page 35
Separate DVD recorder and receiver To receive analogue channels via antenna and record programmes on a separate DVD recorder and receiver, connect three antenna cables and one SCART cables as illustrated: DVD recorder and Set-top box To receive analogue channels via antenna, output sound to Set-top box and record programmes on a DVD recorder, connect two antenna cables, one SCART cable and two digital audio cables as illustrated: Note...
Game console or camcorder The most practical connection for a mobile game console or camcorder may be at the side of the TV. You can, for example, connect the game console or camcorder to VIDEO and AUDIO L/R connectors at the side of the TV. A HDMI connector is also available for high- definition devices.
Í to return to the previous menu. Press MENU to exit. EN-36 7�5 Use Philips EasyLink Your TV supports Philips EasyLink, which enables one-touch play and one-touch standby between EasyLink-compliant devices. Compliant devices must be connected to your TV via HDMI and assigned as described in Section 7.4.1...
7�6 Prepare TV for digital services Scrambled digital TV channels can be decoded with a Conditional Access Module (CAM) and a Smart card provided by a digital TV service operator. The CAM may enable several digital services, depending on the operator and services you choose (for example, pay TV).
Troubleshooting This section describes commonly-encountered issues and accompanying solutions. 9�1 General TV issues The TV does not switch on: • Unplug the mains cord, wait for one minute and plug in the mains again. • Verify that the mains cord is properly connected and that the mains are powered.
You receive poor picture quality from connected devices: • Check that the devices are connected properly. • Verify that picture settings are correctly set. See Section 5.3 Adjust picture settings. The TV did not save my settings: • Verify that the TV is set to which offers you complete flexibility to change settings.
10�1 INTRODUCTION TO PBS MODE The Professional Business Solutions (PBS) mode defines a specific TV or monitor mode (similar to hotel mode). This mode limits the amount of TV controls (e.g. like volume limitation), that a normal user (i.e. hotel guest) can use. The amount of access can be configured in the setup menu by a super-user (e.g. hotel installer). This manual describes how to setup a television channels using Virgin Mode, configure other TV settings and activate the PBS mode.
Page 44
10�2�2 Guest Remote control 22AV1104/10 1. On/Standby . Switches the TV on from standby or back to standby. 2. GUIDE (DVB-T) Toggles the Electronic Program Guide on or off. Only active with digital channels. 3. SOURCE Selects connected devices. 4. SUBTITLE (DVB-T) Activates or deactivates subtitles.
10�3 INITIAL SETUP 10�3�1 Virgin mode – Out Of Box Setting and Initial Setup This TV set includes an installation feature that, at initial set-up of the TV, guides you through the installer menu to apply the proper installation settings. This feature, named Virgin Mode, active when the TV set is unpacked and first powered on, is normally used for installation/setting of first...
For details refer to consumer TV User Guide. The installer should change the TV to Home mode by select Install > Preferences > Location 10�4 DISPLAY SETUP MENUS The TV can display PBS Setup menu by pressing RC2573 MENU key in SETUP mode or by following Guest RC key sequence “319753 [ ”...
Page 47
When APPLICATION is Hotel/Hospital, the limited Guest TV menu can be accessed by guest as below: Refer to consumer TV User Guide for the description of each menu item. When APPLICATION is BUSINESS MONITOR, the normal consumer TV setup menu can be accessed by using guest RC menu key with the additional control features listed in the PBS setup menu.
Page 48
10�4�4 CONTROL SETTINGS • TELEVISION BUTTONS LOCKED – Selection of television buttons locked or unlocked. ON means all television buttons are locked, except the Power button, OFF means all television buttons are enabled, while ALL means all television buttons are locked, including the Power button.
10�4�6 SMARTLOADER TO TV (using USB) Copy TV configuration data (Video, Audio, Channel Table, PBS Mode settings) from USB Memory stick to TV. Upon copying progress completion, an indication message will feedback to PBS-user (“Settings copied to TV”). Note During copying process, the USB memory stick should not be removed to prevent any undersigned functionality of the TV.
Page 50
10�4�8 Select remote control setting 1. Enter Setup menu. 2. Press ▼ to select Remote control� 3. Press ► to enter control setting. 4. Press▼or ▲ to select a setting. 5. Press ► to enter. High security mode • On Access the BDS Hotel Mod_e Setup Menu via the setup remote control only . •Off Access the BDS Hotel Mode Setup Menu via the setup remote control or guest mode remote control.
10�4�9 Smart RC • On Select to use the smart remote control. • Off Disable the use the smart remote control. Add current channel to Pay TV ring Select R0, R1 or R2 setting for the various pay TV channels. 10�5 STORE Activation of this item will store PBS mode...
Page 52
TV. Philips has wall mounts with tilt for hotel TVs as optional accessories. Philips is recommending to position the TV as mentioned above. Positioning the TV differently might have impact on the viewing angle. Philips is not responsible for reduced...
Index Analogue Channel installation 25 Antenna Connect 9 Audio language 19 Automatic Channel installation 24 Back connectors 5 Brightness 17 Care Environment 4 Channels Rename 26 Test digital reception 27 Uninstall 26 Contrast 17 Country Selection 25 Devices Watch 12 Digital Radio 24 Services 35...
Page 54
Screen care 4 Settings Picture Adjust settings 16 Use smart settings 17 Sound Adjust settings 19 TV location Change location 19 Setup devices 34 Sharpness 17 Shop mode 19 Side Connectors 5 Smart settings Current 17 Movie 17 Standard 17 Vivid 17 Software update Check version 24...