Casio 5146 Operation Manual

MO1003-EA
About This Manual
General Guide
• Press C to change from mode to mode.
• In any mode (except a setting mode), press B to illuminate the display.
Timekeeping
You can adjust the Home Time city date and time in the Timekeeping Mode.
• The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
• If the analog time does not match the digital time for any reason, use the procedure
described under "To adjust home positions" to match the analog setting to the digital
setting.
• Pressing D in the Timekeeping Mode toggles digital display between the Home City
Date and Home City Time.
Home City Date
Month Day Seconds
To set the digital time and date
City code
PM indicator Seconds
Hour : Minutes
3. Press C to change the flashing screen content in the sequence shown below to
select the other setting.
City Code
Illumination
Duration
4. When the setting you want to change is flashing, use D or B to change it as
described below.
Screen: To do this:
Change the city code
Toggle the DST setting between
Daylight Saving Time (on) and
Standard Time (OFF).
Toggle between 12-hour (12H) and
24-hour (24H) timekeeping
Reset the seconds to 00
Change the hour and minutes
Change the year, month, or day
Toggle the display illumination
duration between 1.5 seconds (LT1)
and three seconds (LT3)
5. Press A to exit the setting mode.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
Operation Guide 5146
• Depending on the model of your watch, display text
appears either as dark figures on a light background or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
• Button operations are indicated using the letters shown
in the illustration.
• Note that the product illustrations in this manual are
intended for reference only, and so the actual product
may appear somewhat different than depicted by an
illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the "Reference" section.
Timekeeping Mode
Press C.
Home City Time
Day of week
D
PM indicator Hour : Minutes Seconds
1. In the Timekeeping Mode, hold down A for about three
seconds until the currently selected city code flashes in
the upper digital display. This is the setting mode.
2. Use D (east) and B (west) to select the city code you
want.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the "City Code
Table".
12/24-Hour
DST Seconds
Format
Day Month
Year
Do this:
Use D (east) and B
(west).
Press D.
Press D.
Press D.
Use D (+) and B (–).
Press D.
Stopwatch Mode
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
Day of week
DST indicator
12-hour and 24-hour timekeeping
• With the 12-hour format, the PM indicator (P) appears for times in the range of noon to
11:59 p.m. and no indicator appears for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the PM indicator (P).
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.

Stopwatch

Upper display
segments
Hour
Minutes
Speed hand
Important!
• Check to make sure that the speed hand is not moving before you perform any
Stopwatch Mode button operation.
Specifying a Distance Value
You can use the procedure below to specify a distance value, if you want. If you
specify a distance value, the watch will calculate and indicate speed for certain
stopwatch operations.
• The distance value represents kilometers, miles, or any other distance unit you want.
Specifying a distance value of 10.0, for example, can mean 10.0 kilometers or 10.0
miles.
• No speed calculation is performed when 0.0 is specified as the current distance
value.
• For lap time readings, you can specify either the lap distance (when all the laps are
the same distance) or the total race distance.
• For split time readings, you can specify the total race distance only. Though the
watch will indicate a speed each time you take a split reading, they will be based on
the total race distance, and so they will not indicate actual intermediate split speeds.
Countdown Timer Mode
Alarm Mode World Time Mode
1. In the Timekeeping Mode, hold down A for about three
seconds until the currently selected city code flashes in
the upper digital display. This is the setting mode.
2. Press C. This will display the DST setting screen.
3. Use D to toggle the DST setting on (on) and off (OFF).
• The default DST setting is off (OFF).
4. When the setting you want is selected, press A to exit
the setting mode.
• The DST indicator appears to indicate that Daylight
Saving Time is turned on.
You can use the stopwatch to measure elapsed time, lap
times and split times. If you specify a distance value, the
stopwatch also will calculate and display speeds.
• The digital display range of the stopwatch is 99 hours,
59 minutes, 59.999 seconds. The stopwatch continues
to run until you stop it. If it reaches the above limit, it will
restart the time measurement from zero.
• The stopwatch operation continues even if you exit the
Stopwatch Mode. If you exit the Stopwatch Mode while a
stopwatch operation is in progress, the segments along
the top of the upper digital display (upper display
segments) will indicate the seconds of the current time.
Each segment represents one second. This is to let you
know that a stopwatch operation is in progress.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
1