Related Manuals for Sanyo BLOOD BANK MBR-304DR
Summary of Contents for Sanyo BLOOD BANK MBR-304DR
- Page 1 INSTRUCTION MANUAL MBR-304DR MBR-304GR MBR-304D Blood Bank Refrigerator MBR-304G MBR-304G...
-
Page 2: Table Of Contents
1. No part of this manual may be reproduced in any form without the expressed written permission of SANYO. 2. The contents of this manual are subject to change without notice. 3. Please contact SANYO if any point in this manual is unclear or if there are any inaccuracies. SANYO Electric Biomedical Co., Ltd. -
Page 3: Precautions For Safe Operation
PRECAUTIONS FOR SAFE OPERATION It is imperative that the user complies with this manual as it contains important safety advice. Items and procedures are described so that you can use this unit correctly and safely. If the precautions advised are followed, this will prevent possible injury to the user and any other person. - Page 4 PRECAUTIONS FOR SAFE OPERATION WARNING Do not use the unit outdoors. Current leakage or electric shock may result if the unit is exposed to rain water. Only qualified engineers or service personnel should install the unit. The installation by unqualified personnel may cause electric shock or fire. Install the unit on a sturdy floor.
- Page 5 PRECAUTIONS FOR SAFE OPERATION WARNING Disconnect the power supply to the unit prior to any repair or maintenance of the unit in order to prevent electric shock or injury. Ensure you do not inhale or consume medication or aerosols from around the unit at the time of maintenance.
- Page 6 PRECAUTIONS FOR SAFE OPERATION CAUTION Connect the unit to a power source as indicated on the rating label attached to the unit. Use of any other voltage or frequency other than that on the rating label may cause fire or electric shock. Fix the shelves securely (MBR-304D, MBR-304G).
-
Page 7: Cautions For Usage
CAUTIONS FOR USAGE • If the unit is unplugged or the power to the unit is interrupted, do not restart the unit for at least 5 minutes. This protects the compressor. • This inner cabinet is refrigerated by the forced circulation of cooled air inside the chamber. Ensure that the intake and exhaust vents are not blocked. -
Page 8: Environmental Conditions
ENVIRONMENTAL CONDITIONS This equipment is designed to be safe at least under the following conditions (based on the IEC 1010-1): 1. Indoor use; 2. Altitude up to 2000 m; 3. Ambient temperature 5 C to 40 4. Maximum relative humidity 80% for temperature up to 31 at 40 5. -
Page 9: Refrigerator Components
REFRIGERATOR COMPONENTS MBR-304G... - Page 10 15. Caster: Used when moving the unit. When installing the unit the castors can be raised from the ground by using the leveling feet. 16. Leveling foot: Adjust the height of the leveling foot to install the refrigerator in level. See page 12 for details.
- Page 11 REFRIGERATOR COMPONENTS Control panel and keypad 1. Alarm buzzer stop key (BUZZER): To silence the audible alarm, press this key. 2. Temperature display key (UPPER/LOWER): By pressing this key, the displayed temperature is changed; upper monitor bottle temperature, lower monitor bottle temperature, and average temperature of upper and lower monitor bottles are displayed in sequence.
-
Page 12: Installation
INSTALLATION Installation site To operate this unit properly and to obtain maximum performance, install the unit in a location with the following conditions: • A location not subjected to direct sunlight Installation in a location subjected to direct sunlight may lead to inadequate cooling. •... - Page 13 INSTALLATION Installation 1. Remove the packaging materials and tapes Remove all transportation packaging materials and tapes. Open the doors and ventilate the unit. If the outside panels are dirty, clean them with a diluted neutral dishwashing detergent. (Undiluted detergent can damage the plastic components. For the dilution, refer to the instruction of the detergent.) After the cleaning with the diluted...
-
Page 14: Before Commencing Operation
BEFORE COMMENCING OPERATION Preparation of monitor bottle Prior to the operation of the unit, fill the monitor bottles (upper and lower) with 10% glycerol or water using the following procedure: 1. Remove the top and bottom drawer (or shelf). 2. Remove the monitor bottle cover as shown in the figure 1. -
Page 15: Remote Alarm Terminal
BEFORE COMMENCING OPERATION Remote alarm terminal The terminal for remote alarm is installed inside the rear cover of the unit. The alarm is outputted from this terminal. The contact rating is DC 30V, 2 A. Contact output: At normal condition “Open” At abnormal condition “Close”... -
Page 16: Start-Up Of Unit
7. Once the unit operation has been thoroughly checked, begin slowly placing items into the chamber to minimize the temperature rise. Operation after power failure The refrigerator resumes the operation with temperature setting of 4 C after power failure. -
Page 17: Operating Instructions
OPERATING INSTRUCTIONS Storing of items Do not disturb the air circulation in the chamber by the stored items. The disturbed air circulation can cause the freezing of stored items or degrade of temperature distribution in the chamber. Air-intake vent Do not block the air-intake by the stored items near the air-intake vent. Take should be taken not to put any paper or plastic chips near the vent. -
Page 18: Temperature Display
OPERATING INSTRUCTIONS Temperature display The unit is set at the factory to obtain the proper temperature automatically (4 need to set the temperature. Table 1. Temperature display Operation Plug-in the power supply cord and turn on the power switch. Press the temperature display key. - Page 19 This key operation is canceled with the buzzer if the sensor temperature deviates over +/- 1.5 In this case, consult with Sanyo dealer or service personnel. 6-4. The digital display will revert back to current chamber temperature. The calibration that was entered in the previous step should now have an effect on the temperature display.
-
Page 20: Alarms & Safety Functions
ALARMS & SAFETY FUNCTIONS This unit has the alarms and safety functions shown in Table 2, and also self diagnostic functions. Table 2 Alarms and safety functions Alarm & Safety Situation High temperature If the upper or lower temperature sensor senses a temperature ≧... -
Page 21: Routine Maintenance
ROUTINE MAINTENANCE WARNING Always disconnect the power supply to the unit prior to any repair or maintenance of the unit in order to prevent electric shock or injury. Ensure you do not inhale or consume medication or aerosols from around the unit at the time of maintenance. -
Page 22: Disposal Of Unit
ROUTINE MAINTENANCE Replacement of glow starter A glow starter is located upper right side of the cabinet.. 1. Disconnect the power supply plug. 2. Remove the glow starter and replace with a new one. 3. Replace the water-proof rubber. Cleaning of condenser filter This unit is provided with the condenser filter at the bottom of the cabinet. -
Page 23: Troubleshooting
TROUBLESHOOTING If the unit malfunctions, check out the following before calling for service. If nothing operates even when switched on • The power is failed. • The circuit breaker is inactivated. • The unit is not connected to the power supply. The alarm device is activated •... -
Page 24: Specifications
Rated power consumption 220W Noise level Maximum pressure Note :The unit with CE mark complies with EC directives 89/336/EEC, 93/68/EEC and 73/23/EEC. Blood Bank Refrigerator MBR-304G W600 x D680 x H1835 (mm) W520 x D490 x H1150 (mm) 304 L... -
Page 25: Safety Check Sheet
Please fill in this form before servicing. Hand over this form to the service engineer to keep for his and your safety. 1. Refrigerator contents : Risk of infection: Risk of toxicity: Risk from radioactive sources: (List all potentially hazardous materials that have been stored in this unit.) Notes : 2. - Page 26 7FB6P101379001 (9 Sept. 2004) Recycled paper SANYO Electric Biomedical Co., Ltd. 10-15, Hongo 3-Chome Bunkyoku, Tokyo 113-8434 Japan Printed in Japan...