Samsung BN68-02609A-02 Quick Setup Manual

Quick Setup Guide

Congratulations on the purchase of your new Samsung TV.
Read this setup guide to get your TV up and running quickly.
1-800-SAMSUNG (1-800-726-7864)
STOP
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Please do not return this unit.
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
If you have problems operating your
Call Center hours of operation: Mon-Sun, 9:00 AM -12
TV, call:
AM EST.
1-800-SAMSUNG (1-800-726-7864)
To register this product, visit: www.samsung.com/
For web support please visit:
register.
www.samsung.com/support
Step 1
: Install the Stand
Follow the steps below to connect the TV to the stand.
✎
NOTE
x
Make sure to distinguish between the front and back of the Stand and
Guide Stand when assembling them.
x
Make sure that at least two people lift and move the PDP TV.
x
Stand the product up and fasten the screws. If you fasten the screws with
the PDP TV placed down, it may lean to one side.
1 2
With your TV upright, connect the Fasten two screws (M4 X L16) at
TV to the Stand as shown. position 1, and then fasten two
screws (M4 X L16) at position 2.
Front
2
1
Rear
Step 2
: Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1. Lift the cover on the back of the remote
upward as shown in the figure to the
right.
2. Install two AAA batteries.
✎
Make sure to match the +
and - ends of the batteries
to the diagram in the battery
compartment.
3. Replace the cover.
Step 3
: Connect Power and Antenna or Cable
VHF/UHF Antenna
Connect Ant In to
Antenna Cable
(Not Supplied)
• Wall cable jack
• VHF/UHF Antenna
or
• Cable or Satellite box
Ant or Cable Out
Use a 75 ohm (round) cable.
Make sure the AC power cord is plugged in securely to
the wall outlet and the TV.
Step 4
: Connect External Devices
Connecting an AV device (DVD/Blu-ray player, cable/satellite box, etc.)
Use one of the connections below to connect your TV to an external A/V device. We recommend using
HDMI for the highest picture quality.
✎
When connecting to AV IN on the back of your TV, attach the video cable (yellow) to the green jack
next to the AV IN label. The jack will not match the color of the video cable (yellow).
Video Cable
(Not Supplied)
Lowest Quality Connection
Audio/Video connection (480i only)
Using an Audio/Video Cable
Audio Cable
DVD, Blu-ray player, cable box, STB satellite
(Not Supplied)
receiver, VCR
Device
VIDEO OUT AUDIO OUT
Step 5
: Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language, set
the clock mode, and launch the TV's channel memorizing process.
It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow
buttons on your remote. To make a selection, press the ENTERE button.
To skip a screen, press the MENU button. To turn on your TV, press the
button on the remote or on the TV. To run Plug & Play, follow these steps:
1
P
Plug & Play
Using your remote control, select
Select Language of the OSD.
the language for the On Screen
English
Display (OSD), and then press
Language :
Español
the ENTERE button.
Français
U Move E Enter
2
Plug & Play
Select Home Use, and then
press the ENTERE button. If
Select 'Home Use' when installing this TV in your home.
you select Store Demo, the TV
will reset your picture and audio
Store Demo Home Use
settings every 30 minutes.
L Move E Enter
3
Plug & Play
Select the Antenna source
to memorize, you must select Select the Antenna source to memorize.
Antenna Source to same type
Air
as your cable system type. After
Cable
selecting source, select Start;
Auto
then press the ENTERE button
on your remote.
U Move E Enter m Skip
Best Connection
HD connection (up to 720p/1080i)
Using an HDMI Cable
DVD, Blu-ray player, HD cable box, HD STB
HDMI Cable (Not Supplied)
HDMI OUT
Very Good Connection
HDMI to DVI Cable
(Not Supplied)
HD connection (up to 720p/1080i)
Using an HDMI to DVI Cable
DVI OUT
AUDIO OUT
Audio Cable (Not Supplied)
Good Connection
Component connection (up to 720p/1080i)
Using a Component Cable
COMPONENT OUT
Component Cable
(Not Supplied)
AUDIO OUT
✎
Most cable systems are Standard(STD) systems, If you are not sure about
what kind of cable system you have, contact your cable company.
✎
If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After
Plug & Play is complete, set your TV to Channel 3 or 4, according to the
directions for your cable or satellite box.
4
POWER
The TV memorizes the available
channels. This process can take Auto Program in Progress.
up to 45 minutes. DTV Air : --
DTV Cable : --
5
After the TV has memorized the
channels, choose the Clock
Set the Clock Mode.
Mode. Select Auto if you have
a digital channel in your area.
Clock Mode
Select Manual if you don't, or
if you have a cable or satellite
box. When done, press the
ENTERE button.
✎
If you select Manual, the
clock setting screen appears.
6
Select the daylight savings time
Start
setting: Off, On or Auto and then
Start Set to daylight saving time.
press the ENTERE button.
Start
DST
✎
This function is only available
when the Clock Mode is set to
Auto.
Connecting an audio device (Home Theater, etc.)
Connect your TV to your Home Theater or other audio device to enjoy enhanced
Sound quality.
Audio Cable (Not Supplied)
(Set-Top-Box) satellite receiver
Device
Optical Cable (Not Supplied)
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
Device Audio Cable (Not Supplied)
HDMI to DVI Cable (Not Supplied)
DVD, Blu-ray player, cable box,
STB satellite receiver, VCR,
Device
D-Sub Cable (Not Supplied)
Audio Cable (Not Supplied)
7
Select the time zone in which you live, and then press the ENTERE button.
8
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
9
Plug & Play
The Enjoy your TV. screen appears. Then press the ENTERE button.
Air : --
If You Want to Rerun Plug & Play
Cable : -- Cable : 35
1. Press the SOURCE button on your remote, then select TV mode.
48%
2. Press the MENU button on your remote to display the menu.
Stop
3. Press the ▲ or ▼ button to select Setup, and then press the ENTERE
E Enter m Skip
button.
4. Press the ENTERE again to select Plug & Play.
Plug & Play
Auto
Manual
U Move E Enter m Skip
Plug & Play
Off
On
Auto
U Move E Enter m Skip
Analog Audio connection
Using an Audio Cable
Amplifier / DVD home theater
AUDIO IN
Digital Audio connection
Using an Optical Cable
Digital Audio System
OPTICAL
HD connection
Using an HDMI to DVI Cable
AUDIO OUT
DVI OUT
Using a D-Sub Cable
PC OUT
AUDIO OUT
BN68-02609A-02