T Hermostat O Peration; Illing He Opper; Ighting Our Ellet Tove; Ontrol Oard - Lennox Hearth Products Winslow PS40 Installation And Operation Manual

Free-standing pellet stove

Hide thumbs Also See for Winslow PS40:

Installation and operation manual (30 pages)

Installation and operation manual (32 pages)

Table Of Contents

Table of Contents

Original version

operation

ontroL

oard

The control board regulates all functions of the stove. The

following is a list of the board’s components:

• feeding light - lights up when the auger is feeding pellets

into the burn pot.

• Ready Light - lights up when stove is ready to operate.

Igniting Light - lights up when the stove is in the ignition

sequence.

• Start button - is pushed to start the ignition sequence

after the heat selector knob is turned from off.

Heat Selector Knob - is turned to off to shut the stove

off or turned to a setting from 1 to high to regulate the

burn

rate.

• Igniter fuse - six amp fuse to protect igniter heating ele-

ment.

• Control fuse - three amp fuse to protect the control

board.

Heat Selector

Knob

figure

iLLing the

opper

The hopper can be accessed by lifting the lid at the rear

of the top of the stove. The hopper will hold 60 pounds of

pellets. Remove any contents from the hopper and ﬁll with

pellets.

ighting

1. Turn the heat selector knob (see Figure 42) to the heat

level desired - 1 through high - and the ready light will

turn green.

2. Push the start button and the ignite and feeding lights will

come on and the lighting sequence will begin. For about

the next 15 minutes the stove will feed pellets cyclically

into the burn pot, the combustion fan will come on, and

the igniter will heat up. During this sequence, some

smoke in the ﬁrebox is to be expected. After the igniting

sequence is complete, the stove will begin burning at the

level indicated by the heat selector knob.

Note: Upon the stove’s initial light up, or if the stove has

previously run out of pellets, the auger feed tube may not

contain a sufﬁcient number of pellets to allow the stove

to continue burning after the ignition sequence. It may be

necessary to push the start button a second time to run

the start sequence again. It is important to always empty

(when cool) the burn pot of pellets before pushing the start

button a second time.

WARNING

Never empty pellets from the burn pot into the

hopper. Pellets that may appear to be cool may

retain enough heat to ignite other pellets resulting

in smoke or fire damage.

anuaL

peration

After the stove is burning (see lighting above), the heat

selector knob controls the pellet burn rate and the stove’s

heat output. Turning the knob to setting 1 allows the stove

to burn about 1.8 pounds of pellets per hour - about 8,500

BTUs per hour. Turning the knob to high allows the stove

to burn 4.7 pounds of pellets per hour - about 39,000 BTUs

per hour. Once set, the stove will continue to burn at this

rate until shut off.

hermostat

peration

This stove will operate with a low voltage thermostat. See

page 10 for instructions on installing the thermostat. Once

installed, the thermostat will control the operation of the

stove. Important: When connected to a thermostat, it is

necessary to push the ignite button for the initial burn,

when the electrical ﬂow to the stove is interrupted, if the

selector knob is turned to off (and then back on), or if the

stove runs out of pellets and therefore shuts off. After the

initial ignition sequence, when the thermostat calls for heat

(the room temperature is less than the temperature set on

the thermostat) and the heat selector knob is not in the off

position, the stove will burn at the heat selector knob set-

ting. The higher the setting, the quicker the room will heat

up. Once the thermostat no longer calls for heat (the room

is up to the desired temperature), the stove will continue

to burn for one additional hour at the lowest setting. If the

thermostat does not call for heat again during that hour, the

stove will shut off. During that hour, if the thermostat calls

for heat again, the stove will again burn at the heat selector

knob setting until the thermostat no longer calls for heat.

If the stove shuts off after that hour it will relight when the

thermostat calls for heat.

Table of Contents

This manual is also suitable for:

Country winslow ps40

T Hermostat O Peration; Illing He Opper; Ighting Our Ellet Tove; Ontrol Oard - Lennox Hearth Products Winslow PS40 Installation And Operation Manual

Related Manuals for Lennox Hearth Products Winslow PS40

Related Products for Lennox Hearth Products Winslow PS40

This manual is also suitable for:

Table of Contents