1. Manuals
  2. Brands
  3. Kenwood Manuals
  4. Transceiver
  5. TS-870S
  6. Instruction manual

Reading Command Tables; Command Tables - Kenwood TS-870S Instruction Manual

Intelligent digital enhanced communications system
Hide thumbs Also See for TS-870S:
Table of Contents

Advertisement

READING COMMAND TABLES

q
AC
Antenna Tuner THRU/IN -LINE, and tuning START/CANCEL
e
r
t
y
q Command
w Name
e Function of the command
r The format of the command is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Set
command.
t The format of the command for reading the transceiver's current status is shown. When oblique lines are drawn in
the 1st and 2nd columns, there is no Read command.
y The format of the command output from the transceiver is shown. When oblique lines are drawn in the 1st and 2nd
columns, there is no Answer command.
u The number of command digits is shown.
i Corresponds to the parameter of the command format.
o Corresponds to the Format number in the Parameter Table. For the parameter formats, refer to the Parameter
Table {page 84}.
!0 Indicates the function of the parameter.

COMMAND TABLES

Parameters that have a Parameter Function of "NOT USED" are not supported by the TS-870S. Any character except the ASCII control
Note:
codes (00 to 1Fh) and the terminator (;) may be entered for those parameters.
AC ANTENNA TUNER CONTROL
Antenna Tuner THRU/IN -LINE, and tuning START/CANCEL
1
2
3
4
5
6
7
8
9 10 11 12 13 14
A C
P2 P3 ;
1
2
3
4
5
6
7
8
9 10 11 12 13 14
A C
;
1
2
3
4
5
6
7
8
9 10 11 12 13 14
A C P1 P2 P3 ;
AG AF GAIN
Sets or reads AF gain.
1
2
3 4 5 6 7 8 9 10 11 12 13 14
A G
P1
;
1 2 3
4 5 6 7 8 9 10 11 12 13 14
A G
;
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A G
P1
;
w
ANTENNA TUNER CONTROL
1
2
3
4
5
6
7
A
C
P2 P3
;
1
2
3
4
5
6
7
A
C
;
1
2
3
4
5
6
7
A
C P1 P2 P3
;
Parameter Format
Parameter function
P1
30
TUNE THRU/IN
(Answer Only)
P2
30
TUNE THRU/IN
P3
1
TUNE OFF/ON
Note:
P1 is used for Answer only.
Tuning cannot be started if P2 is in the
THRU state (If P2="0", selecting "1" for P3
does not start tuning).
P1: RX THRU/IN
P2: TX THRU/IN
Parameter Format
Parameter function
P1
31
AF GAIN
u
Parameter Format
8
9
10 11 12 13 14
Note:
8
9
10 11 12 13 14
P1 is used for Answer only.
Tuning cannot be started if P2 is in the
THRU state (If P2="0", selecting "1" for P3
8
9
10 11 12 13 14
does not start tuning).
P1: RX THRU/IN
AI
AUTO INFORMATION
Auto information OFF/ON
1
2
3
4
A
I P1
;
1
2
3
4
A
I
;
1
2
3
4
A
I P1 ;
AN ANTENNA NUMBER
Selects antenna connector ANT 1/ ANT 2.
1
2
3
4
A N P1
;
1
2
3
4
A N
;
1
2
3
4
A N P1 ;
APPENDICES ●
!0
i
o
Parameter function
P1
30
TUNE THRU/IN
(Answer Only)
P2
30
TUNE THRU/IN
P3
1
TUNE OFF/ON
P2: TX THRU/IN
Parameter Format
P1
Note:
For other commands, controls whether
5
6
7
8
9 10 11 12 13 14
changing a parameter will or will not trigger
the corresponding Answer command
to be output.
5
6
7
8
9 10 11 12 13 14
Ex:
For IF, the Answer command is output
if the step frequency or RIT/XIT
5
6
7
8
9 10 11 12 13 14
frequency is changed.
Parameter Format
P1
5
6
7
8
9 10 11 12 13 14
5
6
7
8
9 10 11 12 13 14
5
6
7
8
9 10 11 12 13 14
Parameter function
32
AI NUMBER
Parameter function
33
ANTENNA
NUMBER
89

Advertisement

Table of Contents
loading

Related Manuals for Kenwood TS-870S

Related Content for Kenwood TS-870S

This manual is also suitable for:

Ts-870

Table of Contents