Terminator; Types Of Commands; Computer Control Commands - Kenwood TS-870S Instruction Manual

Intelligent digital enhanced communications system
Hide thumbs Also See for TS-870S:
Table of Contents

Advertisement

For-
mat
Name
No.
42
KEYER SPEED
KEYER
43
MESSAGE
KEYER
44
BUFFER
LOAD
45
MESSAGE
LEVEL
46
POWER
47
CONTROL
RF
48
ATTENUATOR
SEMI BREAK-IN
49
DELAY TIME
SYSTEM
50
RESET
VOX DELAY
51
TIME
SUBTONE TABLE FOR FORMAT NO.14
Freq.
Freq.
No.
No.
(Hz)
(Hz)
11
01
67.0
97.4
12
02
71.9
100.0
03
13
74.4
103.5
04
14
77.0
107.2
05
15
79.7
110.9
16
06
82.5
114.8
17
07
85.4
118.8
18
08
88.5
123.0
09
19
91.5
127.3
10
20
94.8
131.8

TERMINATOR

To signal the end of a command, it is necessary to use a
semicolon (;). The digit where this special character
must appear differs depending on commands.
No. of
Format
Digits
Represented in words
3
per minute using 001
(min.)~100 (max.).
Contains the CW
24
message.
0: Buffer space
1
available
1: Buffer space not
available
0: Not recording. A Set
1
command cancels
recording.
1: Channel 1
2: Channel 2
3: Channel 3
4: Channel 4
Represented using 000
3
(min.)~255 (max.).
Represented in watts
3
using 010 (min.)~
100 (max.).
00: 0 dB
2
01: 6 dB
02: 12 dB
03: 18 dB
Represented in msec
4
using 0050~0800.
1: VFO Reset
1
([RX A]+[ ])
2: MR Reset
([A=B]+[ ])
Represented in msec
4
using 0150~2700.
Freq.
Freq.
No.
No.
(Hz)
(Hz)
21
136.5
192.8
31
22
141.3
203.5
32
23
146.2
33
210.7
24
151.4
218.1
34
25
156.7
225.7
35
26
162.2
233.6
36
27
167.9
241.8
37
28
173.8
250.3
38
29
179.9
39
1750
30
186.2

TYPES OF COMMANDS

Commands can be classified as shown below:
Input
Command
(Input to the
transceiver)
Commands
Output
Command
(From the
transceiver)
For example, note the following in the case of the FA
command (Frequency of VFO A):
To set the frequency to 7 MHz, the following
command is sent from the computer to the
transceiver:
"FA00007000000;"
To read the frequency of VFO A, the following
command is sent from the computer to the
transceiver:
"FA;"
When the Read Command above has been sent, the
following command is returned to the computer:
"FA00007000000;"

COMPUTER CONTROL COMMANDS

A summary of the command library for communication
between a computer and the TS-870S is included in this
section. This information can be used if you are
developing your own transceiver control program, or
you are troubleshooting an existing control application.
Command
AC
Antenna Tuner THRU/IN-LINE, and
tuning START/CANCEL
AG
Sets or reads AF gain.
AI
Auto information (OFF/ON)
AN
Selects antenna connector
(ANT 1/ ANT 2).
BC
Sets or reads Beat Cancel.
BI
Sets or reads CW Break-in.
BY
Reads Busy signals.
CG
Sets or reads carrier gain.
DN
MIC DOWN function
EQ
Sets or reads Transmit Equalizer.
EX
Sets or reads Menu.
FA
Sets or reads VFO A frequency.
APPENDICES ●
Set Command
(Sets a
particular
condition.)
Read Command
(Reads an answer.)
Answer Command
(Transmits a condition.)
(Set Command)
(Read Command)
(Answer Command)
Function
85

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ts-870

Table of Contents