Parameter Description - Kenwood TS-870S Instruction Manual

Intelligent digital enhanced communications system
Hide thumbs Also See for TS-870S:
Table of Contents

Advertisement

● APPENDICES

PARAMETER DESCRIPTION

Parameters are used to specify information necessary
to implement the desired command. The parameters
to be used for each command are predetermined. The
number of digits assigned to each parameter is also
predetermined. If a particular parameter is not
applicable to the TS-870S, the parameter digits should
be filled using any character except the ASCII control
codes (00 to 1Fh) and the terminator (;).
BAD COMMAND EXAMPLES:
IS1000; Not enough parameters specified
(No direction given for the IF shift)
IS+100; Not enough digits
(Only three frequency digits given)
IS_+_1000; Unnecessary characters between
parameters
IS+10000; Too many digits
(Five frequency digits given)
PARAMETER TABLE
For-
mat
Name
No.
1
SW
2
MODE
Note: Applicable to
Single Beep and
Morse abbreviation
modes.
3
FUNCTION
4
FREQUENCY
5
RIT/XIT
FREQUENCY
7
MEMORY
CHANNEL
9
MEMORY
CHANNEL
SPLIT DATA
10
MEMORY
LOCKOUT
11
TX/RX
14
TONE NUMBER
16
MODEL
NUMBER
84
No. of
Format
Digits
1
0: OFF
1: ON
0:
5: AM
1
No mode
1: LSB
6: FSK
2: USB
7: CW-R
3: CW
8:
No Mode
4: FM
9: FSK-R
0: VFO A
1
1: VFO B
2: MEMORY
Represented in Hz.
11
Ex.: 00014230000 is
14.230 MHz
The first digit is "+" or "–",
5
and the remaining four
digits indicate the
frequency in Hz.
Ex.: +5320 is +5.32 kHz
"_" can be used for
"+".
Represented using
2
00~99.
0: Receive
1
1: Transmit
0: Not locked out
1
1: Locked out
0: Receive
1
1: Transmit
Represents the Tone
2
number (01~39). See
the Subtone Table on
page 85.
Represents the type of
3
transceiver. The
TS-870S number is 015.
For-
No. of
mat
Name
Digits
No.
22
METER VALUE
24
METER
SWITCH
27
PLAYBACK
CHANNEL
30
ANTENNA
TUNER
31
GAIN
32
AI NUMBER
33
ANTENNA
NUMBER
34
CW BREAK-IN
35
MENU NUMBER
36
MENU
SELECTION
37
RECEIVE
FILTER
DISPLAY
38
FILTER WIDTH
AGC TIME
39
CONSTANT
IF SHIFT
40
DIRECTION
IF SHIFT
41
FREQUENCY
Format
Represented using
4
0000 (min.)~
0030 (max.). Relative
values are output.
0: No selection
1
1: SWR
2: COMP
3: ALC
0: Not playing back. A
1
Set command
cancels playback.
1: Channel 1
2: Channel 2
3: Channel 3
4: Channel 4
1
0: Antenna tuner thru 
1: Antenna tuner in-line
3
Represented using
000 (min.)~255 (max.).
1
0: AI OFF
1: IF command outputs
its Answer command
periodically.
2: For parameter
changes, the
corresponding
Answer command is
output.
3: Both 1 and 2.
1
1: ANT 1
2: ANT 2
1
1: Semi break-in ON
2: Full break-in ON
3
Represented using
000~068.
4
See table on page 87.
8
Represented using
00000000~FFFFFFFDh.
Represented in units of
4
10 Hz using 0000~9999.
Represented using
3
000 (min.)~255 (max.).
000~005: OFF
"+": Upward freq. shift
1
(or "_")
"–": Not used (error
occurs).
Represented in Hz using
4
0000~9999.

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ts-870

Table of Contents