Connections; Using Quick Transfer; Transferring Data; Receiving Data - Kenwood TS-870S Instruction Manual

Intelligent digital enhanced communications system
Hide thumbs Also See for TS-870S:
Table of Contents

Advertisement

11 OPERATOR CONVENIENCES

■ Connections

Connect each end of the interconnecting cable to
the COM connector or the ACC 1 connector on the
transceivers.
You may continue using your DSP-100
DSP-100 Users:
DSP Unit with the Transfer function. Connect the
interconnecting cable to either the CONT IN or CONT OUT
connector on the DSP-100, then connect the unused CONT
connector on the DSP-100 to the ACC 1 connector on the
transceiver. The transceiver connected to the CONT IN
becomes the Master; the transceiver connected to the
CONT OUT connector is the Slave.

USING QUICK TRANSFER

While transmitting data, other functions may work more
Note:
slowly.

■ Transferring Data

The Master is the transceiver that sends data to the
Slave transceiver. If the Master has the RIT function
switched ON, the RIT offset frequency is added to
the receive frequency to be transferred.
1 Switch ON the Transfer function on each
transceiver.
On the TS-870S, activate Menu No. 54
(TRNSFER) function. For the compatible
transceiver, check your Instruction Manual for
the correct method.
2 On the Master transceiver, press
QUICK MEMO [M.IN].
If the Master is a TS-450S/690S, press
[M.IN], select memory channel 00, then press
[M.IN] again.
The displayed receive data is stored in Quick
memory channel 1 on the Master transceiver
(TS-450S/690S: channel 00) and transferred
to the Slave transceiver.
E X T R X
A N T
TS-870S
E X T R X
A N T
66
TS-870S
C O M (9 P )
Cross-wired cable
C O M (9 P )
DIN(6P)
Cross-wired cable

■ Receiving Data

There are two ways that the Slave can receive the
data from the Master:
Quick memory 1
(TS-450S/690S: channel 00), or
VFO
This choice is made on the Slave transceiver. On
the TS-870S, Menu No. 55 (DIRECT) can be set to
OFF to receive data into Quick memory, or to ON to
receive data in a VFO. Check your Instruction
Manual for other transceivers. Set Menu No. 27
(TX INH) to ON for a Slave TS-870S.
When receiving data at the Slave transceiver in the
VFO, the data is transferred to the TX side of the
VFO that is currently selected. If the transferred
frequency is simplex, both the RIT and XIT on the
Slave are set to OFF; if a split frequency is
transferred then XIT is set to OFF but RIT is not
changed on the Slave. The IF filter is determined by
the transferred mode. AIP status is determined by
the transferred receive frequency according to the
AIP band memory.
If the Slave transceiver has a Quick or Conventional
memory channel recalled for transmit when the
transfer is done, the data will be rejected. To receive
data into a VFO, select TX and RX using VFOs.
ACC 1
t
r
Rear Panel view on
TS-450S/690S/850S/950SDX
TS-870S
C O M (9 P )
See IF-232C manual.
IF-232C
RS-232C(25P)
Straight cable
Pin
y
No.
q
1
2
3
w
4
e
5
6
COM Connector
cable
w
e
t
u
i
TS-450S/690S/850S/950SDX
AN T
DIN(6P)
Pin Name
GND
TX/RX
TX/RX
CTS
RTS
NC
w
e
t
u
i

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ts-870

Table of Contents