Related Manuals for Hunter OSCILLATING 90405
Summary of Contents for Hunter OSCILLATING 90405
- Page 1 Form# 44086-01 20101102 ©2010 Hunter Fan Co. Oscillating Oscillating Oscillating Stand Fan Owner’s Manual Model 90405 90434 90435...
-
Page 2: Table Of Contents
Unpacking ... 7 Base Assembly ... 7 Motor Assembly ... 8 Grill Assembly ... 9 Operation... 11 Off / Speed Selection Oscillation Adjustment Maintenance ... 12 Technical Support ... 13 Warranty ... 13 Products ... 15 ©2010 Hunter Fan Co. 44086-01 20101102... -
Page 3: Introduction
4. DO NOT put fan in a damp place or where humidity is high-such as a bathroom. 5. The fan should be placed on a flat, stable surface or tabletop to avoid overturning. - Page 4 14. DO NOT operate fan in the presence of explosive and/or flammable fumes. 15. DO NOT place fan or any parts near an open flame, cooking or any other heating appliances. 16. DO NOT use near curtains, plants, window treatments, etc.
-
Page 5: Grounding
Figure NOTE: The adapters ARE NOT supplied with this fan. Read, follow, and save the instructions that are included with the adapter you choose. Do not use an adapter if your electrical outlet can accommodate the grounding pin. -
Page 6: Fused Plug
DO NOT remove, replace, repair or tamper with the originally supplied plug. If the Fan does not function properly, it may be due to the safety device incorporated in this plug. If the fuse fails, it is generally due to a short circuit or circuit overload. -
Page 7: Unpacking
Carefully remove all items from the box. NOTE: It is best to have someone hold the box while you lift the fan and the protective packaging out of the carton. Make sure all shipping materials are removed from fan before operating. -
Page 8: Motor Assembly
After securing the motor(5), Screw in the Tilt Adjustment Knob(8) securely. Figure 10. This Knob allows you to adjust the fans angle. ©2010 Hunter Fan Co. (5) Motor Screw (7) Motor Knob... -
Page 9: Grill Assembly
4. Tighten the Screw on the Blade(10( to secure it to the Motor(5). Figure 14. Caution: Ensure when tightening the screw on the back of the fan blade, you tighten it on the flat part of the post. ©2010 Hunter Fan Co. Handle... - Page 10 5. Straighten the Cord from the Motor along the Telescoping Pole and Snap the Cord Clip over the cord onto the Pole so the cord rests in the notch on the Clip. Figure 18. ©2010 Hunter Fan Co. (9) Back Grill (12) Grill Ring Cord...
-
Page 11: Operation
To turn the fan on and off / control the speed. Turn the speed knob on the top of the motor to the porper setting. Figure 19. To allow the fan to oscillate, push the Knob beside the fan speed control down. -
Page 12: Maintenance
A vacuum cleaner hose can be used to clean these vents. DO NOT immerse the fan in water or any other liquid. CLEANING THE GRILL AND BLADE: 1. Turn the fan off and unplug from the electrical outlet. -
Page 13: Technical Support
Central Time. You may also contact us over the Internet at www.hunterfan.com. WarranTy The Hunter Fan Company makes the following limited warranty to the user or consumer purchaser of this Hunter Portable fan: If your Hunter Portable Fan motor fails at any time within... - Page 14 OR OTHER FAN PART, IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH MOTORS AND OTHER PARTS. This warranty is voided if your Hunter Fan is not purchased and used in the USA. This warranty excludes and does not cover defects,...
-
Page 15: Products
Proof of purchase is required when requesting warranty service. The purchaser must present sales receipt or other document that establishes proof of purchase. IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW LIMITATIONS ON...