Cub Cadet 19A70001000 Operator's Manual

Twin rear bagger kit for i1000 series lawn tractors with a 42” timed deck

Advertisement

Quick Links

To The Owner • Carton Contents • Assembly • Parts Lists • Warranty
OPERATOR'S MANUAL
Twin Rear Bagger Kit
For i1000 Series Lawn Tractors
with a 42" Timed Deck
Model 19A70001000
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
FORM NO. 769-03805A
CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
4/10/2008
PRINTED IN U.S.A.

Advertisement

Table of Contents
loading

Summary of Contents for Cub Cadet 19A70001000

  • Page 1 Twin Rear Bagger Kit For i1000 Series Lawn Tractors with a 42” Timed Deck Model 19A70001000 IMPORTANT READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION FORM NO. 769-03805A CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 4/10/2008 PRINTED IN U.S.A.
  • Page 2: Customer Support

    Click on the appropriate button and help is immediately available. • Phone our Customer Dealer Referral Line, to find a dealer nearest you, at 1(877) 282-8684. The Model 19A70001000 Twin Bag Grass Collector is a grass collection system specifically designed for use on Cub Cadet I-1000 Series lawn tractors equipped with a 42-inch timed mowing deck.
  • Page 3 NOTES Use this page to make notes and write down important information.
  • Page 4: Contents Of Carton

    Before beginning installation, remove all parts from the carton to make sure everything is present. Carton contents are listed below and shown in Figure 2-1. One Chute Tube One Discharge Chute Assembly Carton Two Grass Bag Assemblies Contents One Support Tube One Grass Catcher Cover Assembly If you are missing any parts, call the Customer...
  • Page 5: Contents Of Hardware Pack

    CONTENTS OF HARDWARE PACK This grass collector kit is shipped with a hardware pack enclosed. Please check your hardware pack against the illustration below. Assembling and Attaching Mounting Bracket Hex Bolt 5/16-18 x .750 (6) Flange Lock Nut 5/16-18 (6) Hex Bolt 1/4-20 x .620 (8) Flange Lock Nut...
  • Page 6 Assembling and Attaching The Bracket Assembly IMPORTANT: Before assembly, place the tractor on Assembling a firm, level surface, disengage the PTO, stop the tractor engine and set the parking brake. 1. Assemble the mounting bracket assembly as shown Attaching in Figure 3-1. NOTE: The mounting bracket assembly may have been Mounting preassembled at the factory, if this is the case, skip Step...
  • Page 7: Grass Bag

    Attaching Grass Bags & Grass Bag Cover 1. Place the support tube in position on the rear of unit by sliding the support tube down through the holes in the left side of the bracket assembly. Use the inside hole on the bracket assembly. Refer to Figure 4-1. 2.
  • Page 8 Attaching Discharge Chute 1. Lower the deck to its lowest position. 2. Raise the chute deflector on the deck (A) and hold it while you position the discharge chute over the chute opening. See Fig. 5-1. Attaching 3. Insert the pin (B) on the discharge chute into the hole on the deck as indicated by the arrow in Fig.
  • Page 9 NOTES Use this page to take notes and write down important information.
  • Page 11: Illustrated Parts List

    PART DESCRIPTION NUMBER 16587D Bracket Support 16592 Support Tube Assembly 764-0221 Catcher Bag 664-04017 Grass catcher Cover Assembly 683-04348 Mounting Bracket - RH 683-04350 Mounting Bracket - LH 710-0597 Screw 1/4-20 x 1” 710-0751 Hex Screw 1/4-20 x0.620 710-3008 Hex Screw 5/16-18 x 0.75” 711-0309A Clevis Pin 711-04069...
  • Page 12 Please see the operator’s manual for information on required maintenance and service intervals. The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased or leased and used in the United...

Table of Contents