Char-Broil COMMERCIAL 463268008 Product Manual page 8

WARNING
Turn controls and gas source or tank OFF when not
in use.
CAUTION
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Match-Lighting
Do not lean over grill while lighting.
1. OFF all burner control valves.
Turn
2. Open lid. Turn on gas at LP cylinder.
3. Place lit match into match holder (hanging from cart side
panel), then into lighting hole on right or left side of grill.
4. Push in and turn far right or far left burner knob to HIGH
Be sure burner lights and stays lit.
5. Light adjacent burners in sequence by pushing knobs in and
turning to HIGH .
Sideburner Ignitor Lighting
Do not lean over grill while lighting.
1. OFF all burner control valves.
Turn
2. Open sideburner lid. Turn on gas at LP cylinder.
3. Turn sideburner knob to HIGH
ELECTRONIC IGNITOR button.
4. If sideburner does NOT light, turn knob to OFF
minutes, then repeat lighting procedure.
Sideburner Match Lighting
1. OFF all burner control valves.
Turn
2. Open sideburner lid. Turn on gas
at LP cylinder.
3. Place lit match near burner.
4. Turn sideburner knob to
HIGH .Be sure burner
lights and stays lit.
8 • 463268008
.
, push and hold
, wait 5
Burner Flame Check
• Remove cooking grates and flame tamers. Light burners, rotate
knobs from HIGH to LOW
flame in LOW position than seen on HIGH. Perform burner
flame check on sideburner, also. Always check flame prior to
each use. If only low flame is seen refer to "Sudden drop or low
flame" in the Troubleshooting Section.
Turning Grill Off
OFF
• Turn all knobs to
turning hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Press and hold electronic ignitor
button. "Click" should be heard and spark seen each time
between collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valves. Knobs lock in
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to LOW position then turn back to
OFF
position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use only
valve/hose/regulator specified by manufacturer.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Plastic parts: Wash with warm soapy water and wipe dry.
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
• Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.
• Stainless steel surfaces: To maintain your grill's high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.
. You should see a smaller
HIGH
LOW
position. Turn LP cylinder off by
OFF
position. To check