Impressa S9, S8, S7 Fully Automatic Coffee & Espresso Center with Claris Water Care System Operating Instructions and Warranty Customer Service 1-800-220-5701 Impressa S9 shown here with frothXpress Plus installed...
Page 2
• Never clean with scouring powders or hard implements. JURA-CAPRESSO Jura was founded in 1931 in Switzerland. Capresso was founded in 1994 in the USA. Both companies have joined forces in the US to bring you the best Fully Automatic Coffee Centers available anywhere.
FIG. 1 * frothXpress-Plus System see Fig. 15, 15a, 16 1. Height-Adjustable Coffee Spout 2. Operating Display (See Fig.2) 3. Removable Water Tank Low Water Flotation Device(Inside) 5. Claris Water Care Cartridge (Not Installed) 6. Lid for Water Tank 7. Holder for Claris Water Cartridge 8.
Page 4
Operating Display FIG. 2 C O F F E E R E A D Y Display Dialog System ON/OFF Button SPECIAL COFFEE Button 1-CUP SMALL Button 1-CUP LARGE Button RINSE Button 2-CUP SMALL Button 2-CUP LARGE Button Steam System FIG. 3 STEAM PORTION Button Selector Switch for Coffee or Hot Water...
Page 6
FIG. 13 FIG. 14 Steaming FIG. 15a frothXpress Plus DIAL attached Fig.15-17: Standard with Impressa S9, separately available with Impressa S7 and S8. FIG. 14a Frothing: down FIG. 16 Frothing range Steam only no siphoning Steaming range FIG. 15 FIG. 17 FIG.
You can also send us a FAX at: 201-767-9684 or EMAIL us at contact@capresso.com 3. WELCOME TO THE IMPRESSA S7, S8, S9 This fully automatic espresso coffee center is completely pro- grammable and extremely user friendly. With two independent Thermoblock heating systems it can switch from brewing coffee to frothing milk without any up- or down-time.
and most aromatic cup of coffee. This is also the reason why many European restaurants and hotels will serve you freshly pressured brewed coffee only. Experiment with your new machine and prepare yourself the best and most enjoyable cup of coffee! 4.1 PRESSURE BREWING You can make any quantity of coffee from note: in order to create the "crema"...
PLEASE, DO... • Fill water tank with fresh, cold water only. • Remove any foreign particles (small stones) from coffee beans. • Let frozen beans thaw for 3 to 4 hours before pouring them into the bean container. All Display Messages Are Shown in GREEN 6.
RINSE UNIT • Place a container under the coffee-spout (Fig. 8b) and press the RINSE button (Fig. 2,F). UNIT RINSING COFFEE READY Attention: You can only make coffee when the display reads COFFEE READY. CUP ILLUMINATION The cup illumination adds a dramatic touch to brewing coffee. Providing the machine is plugged in, you can activate the cup illumination for 3 minutes by pressing any button.
• Eliminates decalcifying. When using the Claris water cartridge, you never need to decalcify your machine. • Is available through your retailer, the enclosed mail order form, or through www.capresso.com, or call 1-800-220-5701. 11a. INSTALLING THE CLARIS CARTRIDGE • Make sure the water tank is empty.
cartridge (Fig.12). • Insert the cartridge with its tapered end down and the exten- sion piece up. Make sure it fits snugly over the white mesh piece inside the water container. Push down gently (Fig.13). • Close the holder for the cartridge so that it engages in the water tank (Fig.12).
The frothXpress-PLUS system which is included with the S9. For the S7 and S8 order this system with the enclosed order form or through our website: www.capresso.com. Recommendation: • If you froth for only one or two cups at a time and want 100% control over the frothing/steaming process, the Dual Frother- PLUS might be the preferred equipment.
14a. USING THE DUAL FROTHER PLUS Frothing Position: The cylinder of the frother is pushed down. Steaming Position: The cylinder is pushed up ( see Fig. 14). • Fill at least 4 to 5 oz. of cold milk into a frothing pitcher. The pitcher should have at least a 10 to 12 oz.
• Assemble the milk container as shown in Fig. 15. • Attach the frothXpress-PLUS system as shown in Fig. 15a. Important: This system siphons milk and mixes it inside the frothXpress with hot steam. It is necessary that all parts are con- nected tightly, otherwise the siphoning process will not work.
• Now froth or steam as described in chapter 14c. 14e. HOT CHOCOLATE, CAFE MOCHA For hot chocolate fill the milk container with the desired amount of chocolate syrup, add cold milk and stir well. Then proceed as described under "Frothing". Adding a shot or two of espresso makes it a Café...
• To begin programming, open cover, press and hold the P button until you hear a "beep." The display will always show the first function: POWDER QUANTITY / PRESS KEY. You are now in programming mode. 15.1 PROGRAMMING POWDER QUANTITY COFFEE READY •...
When the actual brewing starts the display alternates the following messages: ENOUGH COFFEE? • When the desired amount of coffee is in your cup, press the P button. The machine stops brewing and the display shows: –_ _ _ ll_ _ _+ At this time you have two options: Option 1: Press the P button.
15.7 PROGRAMMING WATER HARDNESS (This function only comes up if the Claris Filter Cartridge is set to FILTER NO.) To change the setting for the water hardness see chapter 10. 15.8 PROGRAMMING ECONOMY MODE In the setting ECONOMY MODE ON steam turns off 10 minutes after last use of steam.
15.11 PROGRAMMING AUTO SHUT-OFF TIME The machine is programmed to shut off 5 hours after last use. You can select from ⁄ hour to 9 hour shut off or manual shut off. COFFEE READY • Press the P button. POWDER QUANTITY / PRESS KEY •...
• Remove the used water tray carefully since there is water in it (Fig.1, Fig.18, Fig.19) ATTENTION: Do not unplug the machine while you are emptying the coffee grounds. • Empty the used coffee container and the water tray (drawer). •...
16.7 CLEANING METAL CONTACTS EMPTY TRAY/CLEAN CONTACTS • Remove used water tray (Fig.1, 18). • Clean the metal contacts (Fig. 20) with hot water and dish- washing liquid. Use a household brush if necessary. • Replace water tray. COFFEE READY 16.8 CLEANING THE FROTHER SYSTEMS See chapters 14b, 14f and 14g.
the tray for approx. 20 seconds and then replace it. • Place a large container (24 oz.) underneath the coffee spout (Fig.1, 1). ADD TABLET/ PRESS CLEANING • Open the ground coffee funnel lid (Fig.1,10) and drop one white tablet into the opening (Fig.23). •...
• Turn selector switch (Fig. 3L) to the water symbol and press the DECALC button (Fig. 3A, T1). • The machine will pump the mixture in intervals through the steam nozzle into the container underneath. During this time the display will show: UNIT DECALC/PLEASE WAIT After about 12 minutes the machine "beeps".
For Home Use: Limited One Year Warranty For Office and Commercial Use: Limited Six Month Warranty This warranty covers your IMPRESSA S7, S8 and S9. This war- ranty is in effect for the period described above from the date of the first consumer purchase and is limited to the United States of America.
time, loss of the use of the machine or other costs relating to the care and custody of the machine. The terms “consequential damages” refer to the cost of repairing or replacing other prop- erty which is damaged when this machine does not work prop- erly.
Turn the machine on. Wait until all noise has stopped. The disposable chute should retract. Remove the drawer, replace the used coffee container and insert it back into the machine. Check if the drawer comes out easily. Jura-Capresso LLC. 81 Ruckman Road Closter, NJ 07624 1-800-220-5701 • 201-767-3999 Fax: 201-767-9684 email: contact@capresso.com...