Canon IMAGE FORMULA DR-6010C User Manual
  1. Manuals
  2. Brands
  3. Canon Manuals
  4. Scanner
  5. IMAGE FORMULA DR-6010C
  6. User manual

Canon IMAGE FORMULA DR-6010C User Manual

Canon scanner user manual
Hide thumbs Also See for IMAGE FORMULA DR-6010C:
Table of Contents

Advertisement

Quick Links

User Manual
Please read this manual before operating this scanner.
After you finish reading this manual, store it in a safe
place for future reference.

Advertisement

Table of Contents
loading

Related Manuals for Canon IMAGE FORMULA DR-6010C

Summary of Contents for Canon IMAGE FORMULA DR-6010C

  • Page 1 User Manual Please read this manual before operating this scanner. After you finish reading this manual, store it in a safe place for future reference.
  • Page 2 DR-6010C: Model M11072 Trademarks • Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries. • imageFORMULA is a trademark of CANON ELECTRONICS INC.
  • Page 3 INTRODUCTION INTRODUCTION Thank you for purchasing the Canon DR-6010C Document Scanner. Please read this manual thoroughly before using the scanner to familiarize yourself with its capabilities, and to make the most of its many functions. After reading this manual, store it in a safe place for future reference.
  • Page 4 INTRODUCTION Symbols Used in This Manual The following symbols are used in this manual to explain procedures, restrictions, handling precautions, and instructions that should be observed for safety. WARNING Indicates a warning concerning operations that may lead to death or injury to persons if not performed correctly.
  • Page 5 User Manual Hardware...

  • Page 6: Table Of Contents

    Important Safety Instructions ...1-1 Installation Location...1-1 Power ...1-2 Moving the Scanner ... 1-2 Handling ...1-3 Disposal... 1-4 Features of the DR-6010C Document Scanner... 1-5 Names and Functions of Parts...1-7 Chapter2 Setup ...2-1 Setup Procedure...2-1 Installation Requirements ...2-2 Installing the Software ...2-4 Setup Disc ...2-4...
  • Page 7 Removing and Attaching the Rollers...4-5 Roller Replacement Cycle...4-5 Resetting the Counter ...4-6 Removing/Attaching the Roller Unit ...4-9 Removing and Attaching the Retard Roller ...4-11 Chapter5 Troubleshooting ...5-1 Troubleshooting ...5-1 Uninstalling Software...5-6 Uninstalling the ISIS/TWAIN Driver ...5-7 Uninstalling the Job Registration Tool ...5-8 Uninstalling CapturePerfect 3.0 ...5-10 Chapter6 Appendix ...6-1...

  • Page 8: Chapter1

    Chapter 1 1-1 Important Safety Instructions To ensure the safe operation of this scanner, be sure to read the safety warnings and precautions described below. Installation Location The performance of this scanner is affected by the environment in which it is installed. Make sure that the location where the scanner is installed meets the following environmental requirements.

  • Page 9: Power

    • Keep the area around the power plug clear of objects so that the power cord can be disconnected easily in an emergency. • If you have any questions regarding the power supply, contact your local authorized Canon dealer or service representative for further information.

  • Page 10: Handling

    ■ Do not use power cords other than the power cord provided with this scanner. ■ Never try to take the scanner apart or modify it in any way, as this is dangerous and may lead to a fire or electric shock.

  • Page 11: Disposal

    Chapter 1 Before Using the Scanner ■ Do not place objects on top of the scanner. Such objects may tip or fall over, resulting in personal injury. ■ When unplugging the power cord, grasp it firmly by its plug. Do not pull directly on the power cord, as this may damage or expose the cord’s internal wiring, resulting in a fire or...

  • Page 12: Features Of The Dr-6010C Document Scanner

    • Fast Document Feeding The scanner can scan a maximum of 60 documents per minute in a range of sizes from business cards to LTR/A4 size. (Scanning conditions: Black and white, LTR/A4 size portrait, 200 dpi.) Scanning speed is the same for both color and grayscale scanning.
  • Page 13 This mode may not function effectively, depending on the document type. • Dropout Color The scanner is equipped with a Dropout Color function that enables you to specify a color for the scanner to omit from the scanned image. •...

  • Page 14: Names And Functions Of Parts

    1-3 Names and Functions of Parts This section describes the name and function of each part. Make sure to read this section and familiarize yourself with the parts of the scanner before using the scanner. ■ Front View (Feed Tray Open)

  • Page 15: Back View

    Hi-Speed USB 2.0. CAUTION • Do not block the ventilation openings. Doing so could cause the scanner to overheat, creating a risk of fire. • Do not connect both a USB cable and a SCSI cable at the same time. Doing so may cause a malfunction.

  • Page 16: Chapter2

    • If you connect the scanner to the computer before installing the software, a wizard screen such as shown below will appear when you turn power to the scanner ON. In such a case, click the [Cancel] button to close the wizard screen and then turn power to the scanner OFF.

  • Page 17: Installation Requirements

    - Normal operation is not guaranteed with all USB interfaces, even if present as standard equipment on the computer. For details, consult your local authorized Canon dealer. - The USB cable you are using should be the one originally included with the scanner or a Hi-Speed USB 2.0 compatible cable.
  • Page 18 • Even if the computer satisfies the recommended specifications, the scanning speed may vary, depending on the scan settings. • The ISIS/TWAIN Drivers provided with the scanner do not necessarily operate on all ISIS- or TWAIN-compatible applications. For details, contact your application software retailer.

  • Page 19: Installing The Software

    This section describes how to install the required software. Setup Disc When you insert the Setup disc supplied with the scanner into the CD-ROM drive of your computer, the menu shown below should appear. If this menu does not appear, use Explorer to access the CD- ROM drive and execute the file “SETUP.EXE.”...

  • Page 20: Software Installation

    • When you select [Typical Installation], all of the displayed software and the User Manual will be installed automatically. If you want to reinstall only specific software that you have previously uninstalled, select [Custom Installation] and specify the software. • The DR-6010C driver installation comprises the Scanner Driver and Job Tool installation.
  • Page 21 Chapter 2 Setup Click [Install]. Installation of the DR-6010C driver begins. Click [Next]. The software license agreement appears. Read the license agreement and click [Yes] to accept it. The DR-6010C driver is installed.
  • Page 22 Chapter 2 Setup Next, the job tool software is installed. The DR-6010C driver installation is complete. Click [Finish]. Installation of CapturePerfect 3.0 starts.
  • Page 23 Chapter 2 Setup Click [Next]. The software license agreement appears. Read the license agreement and click [Yes] to accept it. The installation location screen appears. Click [Next]. CapturePerfect is installed. The CapturePerfect installation is complete.
  • Page 24 Chapter 2 Setup Click [Finish]. Installation of the User Manual starts. Click [Next]. The User Manual is installed. The User Manual installation is complete. Click [Finish]. The installation completion screen appears.
  • Page 25 Chapter 2 Setup Click [Exit]. Click [Back] to return to the menu screen. After the software installation is complete, you can connect the scanner to the computer. (See “2-4 Connecting the Scanner to the Computer,” on p. 2-11.) 2-10...

  • Page 26: Connecting The Scanner To The Computer

    Verify that the power switch of the scanner is OFF. If the power switch is in the ON position, push the switch to set it to OFF. Plug the supplied power cord into the power connector on the back of the scanner. a Power Connector...

  • Page 27: Using A Scsi Connection

    SCSI connector on the computer. • The SCSI ID of the scanner is set to “SCSI ID = 2” by default. When using a daisy-chain configuration with other SCSI devices, set the DIP switches so that there is no duplication of SCSI ID numbers in the system.
  • Page 28 Plug the supplied power cord into the power connector on the rear of the unit. a 120 V Type 220-240 V Type Connect the power cord into an AC outlet. b Use the SCSI cable to connect the scanner to the computer. Power switch OFF position ON position 2-13...

  • Page 29: Turning The Power On

    IMPORTANT • When connecting the scanner to the computer using a SCSI cable, be sure to turn power to the scanner ON first, and then turn power to the computer ON. If you turn power to the computer ON first, the scanner may not be properly recognized by the computer.
  • Page 30 • In Windows Vista and Windows XP, a message appears when installation is complete. • In Windows 2000, no message appears when installation is complete. • The DR-6010C is installed in Device Manager under [Imaging Devices] as [CANON DR- 6010C USB] or [CANON DR-6010C SCSI].

  • Page 31: Chapter3

    ID Cards (*1) The DR-6010C offers two document eject configurations: U-turn path (the document is ejected to the document eject tray at the front of the scanner) and straight path (the document is ejected to the back of the scanner.) U-turn Path (*2) You can scan documents up to 39.2”...
  • Page 32 Scanning different sizes and types of paper together can cause the scanner to jam. • Scanning documents before the ink is dry can cause problems with the scanner. Always make sure that the ink on a document is dry before scanning it.

  • Page 33: Document Tray And Eject Tray

    The scanner has two eject methods: documents can be ejected to the front of the scanner in a U- turn path, or to the back of the scanner in a straight path. You can switch between these methods by opening or closing the document eject tray 2. Select an eject method according to your needs.
  • Page 34 IMPORTANT • Be sure there is enough space for documents that are ejected at the back of the scanner when using the straight path. If there is not enough space for the ejected pages, the documents may be damaged or a paper jam may occur.

  • Page 35: Placing Documents

    ■ Do not wear loose clothing or jewelry that may get caught in the scanner while you are using it. This may result in personal injury. Be extra careful of neckties and long hair.
  • Page 36 Chapter 3 Basic Operation CAUTION ■ Do not place the documents on top of the scanner to align them. Doing so may cause a malfunction. ■ When placing documents into the feed tray, take care not to cut your hands on the edges of the paper.

  • Page 37: Feeding In The Bypass Mode

    Start scanning. IMPORTANT • If feeding stops due to a system error or paper jam while the scanner is scanning, resolve the problem, make sure that the scanned image of the last page that was successfully fed has been stored, and then resume scanning the remaining document pages.
  • Page 38 ■ After you finish scanning, close the document feed tray and the document eject tray extension to prevent damage to the scanner while it is not being used. see “Feeding in the Page Separation Mode,” on...

  • Page 39: Job Function

    In addition to using scanning applications, such as Capture Perfect 3.0 to perform scanning, the DR- 6010C is equipped with the Job Function. The Job Function enables you to scan simply by touching a job button on the scanner. This section provides an overview of the Job Function and describes the steps for using it.

  • Page 40: Job Registration Tool

    Save as file: Saves scanned image data as PDF files in the [Pictures] folder. • If you assign scan functions to all three job buttons on the scanner, use the Start and Stop buttons on the Scan Panel to start or stop scanning.

  • Page 41: Scanning With The Job Function

    Chapter 3 Basic Operation Scanning With the Job Function To scan using the job function, use the following procedure. Place the documents into the feed tray. Press the job button c to start the job. The DR-6010C monitor appears, and scanning starts. When scanning is complete, the image data are sent according to the preset conditions.

  • Page 42: About Launcher

    Chapter 3 Basic Operation About Launcher To use the Launcher feature, it is necessary to first change the Windows event settings as described below, and specify an application for each job button. Note • By default, all applications supporting the event function are enabled. If you do not change the event setting before you use the Launcher feature of the DR-6010C, the dialog box shown below will appear.
  • Page 43 Chapter 3 Basic Operation 2. Click [Hardware and Sound]. Note Under Windows XP, click [Printers and Other Hardware]. 3. Click [Scanners and Cameras]. Note Under Windows 2000, double click [Scanners and Cameras]. 3-13...
  • Page 44 Chapter 3 Basic Operation 4. Select [CANON DR-6010C USB] or [CANON DR-6010C SCSI] and click [Properties]. The [CANON DR-6010C USB Properties] or [CANON DR-6010C SCSI Properties] window appears. 5. Click the [Events] tab. Under [Scanner events], select the button whose setting you want to change (Button No. 1, Button No.
  • Page 45 If the [Disable device events] check box is selected, the Job Function cannot be used. Make sure that this check box is not selected. Click [OK] to close [CANON DR-6010C USB Properties]. Restart Windows to enable the new event settings.

  • Page 46: Captureperfect 3.0

    CapturePerfect 3.0 online Help. Familiarize yourself with CapturePerfect 3.0 by reading these sources before using the application. What is CapturePerfect 3.0 CapturePerfect 3.0 is an ISIS-compatible application developed for Canon document scanners. CapturePerfect 3.0 includes the following modes. Select the desired scan mode from the Scan menu to perform scanning.
  • Page 47 [Pictures] under the folder [Documents]. • Scan To Presentation This mode is useful when the scanner is used in environments, such as conference halls, where it can be connected to large displays or projectors. CapturePerfect 3.0 is switched to full-screen display, the document is scanned, and the scanned image is displayed at full size on the screen.

  • Page 48: Using Captureperfect 3.0

    Click the Windows [Start] button [CapturePerfect 3.0] CapturePerfect 3.0 starts up. Follow the procedure below to select the Canon DR-6010C Document Scanner as the scanner to be used. 1. On the [Scan] menu, click [Select Scanner]. click [Programs] ([All Programs] for Windows XP) [CapturePerfect 3.0].
  • Page 49 3. Set the Default Page Size and click [OK]. Note This dialog box is displayed only when you select [Canon DR-6010C] for the first time and click [OK], or when you click [Setup] for [Scanner Selection]. On the [Scan] menu, click [Scanner Setting].
  • Page 50 Chapter 3 Basic Operation Set the scan settings. For more information on scan settings, Place your document. On the [Scan] menu, select [Scan Batch to File]. The [Scan Batch to File Setting] dialog box opens. For more details on how to scan documents, see the CapturePerfect 3.0 Operation Guide and CapturePerfect Online Help.

  • Page 51: Scan Panel

    Chapter 3 Basic Operation When there are no more pages of the document to scan, scanning stops. Scanning resumes or ends according to the Feeding Option setting in the scanner setup. • Feeding Option is set to “Standard Feeding”: The Continue dialog box is displayed. Place the next document, and click [Continue scanning] to resume scanning, or click [Stop Scanning] to end scanning.
  • Page 52 Chapter 3 Basic Operation Scan Panel Functions The Scan Panel has the following functions. a Start button If Feeding Option is set to “Panel-Feeding,” clicking this button starts scanning. b Stop button Stops scanning. c Job display When the Start and Stop functions are assigned to the job buttons, [Start] and [Stop] are shown here.

  • Page 53: Using Patchcode Sheets

    To open patchcode sheets you need CapturePerfect 3.0, which is provided with the scanner, or an application, which supports PDF format files. IMPORTANT Patchcode sheets must be printed in their original size. The scanner may not recognize them as patchcode sheets if they are enlarged or reduced. is being used.

  • Page 54: Patchcode Pattern Function

    There are two types of patchcodes and their function changes according to their pattern. ■ PATCH T (FILE A) When the scanner recognizes this patchcode printed on a patchcode sheet, it creates a separate file for the document that comes after the patchcode sheet.
  • Page 55 Make sure to keep the patchcode sheets clean. In particular, the effective area for detecting patterns should be kept clean. Also, do not fold them or allow them to become creased. If this happens, the scanner will not be able to read them. 3-25...

  • Page 56: Clearing A Paper Jam

    Chapter 3 Basic Operation 3-7 Clearing a Paper Jam When paper jams occur during scanning, use the following procedure to clear them. CAUTION When removing jammed paper, take care not to cut your hands on the edges of the paper. Remove any documents that have been left in the eject tray, and close the eject tray guide.
  • Page 57 When closing the upper unit, be careful not to get your fingers caught, as this may result in personal injury. IMPORTANT Do not force the upper unit to close. Doing so may damage the scanner. Note • After removing the jammed paper, check to see if the last page was scanned, and then continue scanning.
  • Page 58 Chapter 3 Basic Operation • If a paper jam occurs when “Rapid recover system” is enabled in the ISIS/TWAIN driver settings, the image data of the document is not saved and scanning stops. This allows you to continue scanning from the document that caused the paper jam after the paper jam is fixed.

  • Page 59: Other Functions

    • The maximum size for the combined image is A3. When using the Folio function for an irregular-sized document, set Page Size to “Auto-detection.” • When you face the front of the scanner, the fold should be on the right side. IMPORTANT •...

  • Page 60: Double Feed Detection Function

    Long Document Mode Normally, the scanner can scan documents up to 14" (356 mm) long. However, if you change the paper size setting to Long Document mode, you can scan documents up to a maximum of 39.2"...
  • Page 61 Chapter 3 Basic Operation • When scanning in the Long Document mode, if the document is placed on the scanner in a skewed position, it may be damaged. Be careful to place the document so that it is not skewed.
  • Page 62 Chapter 3 Basic Operation 3. Click [Scanners and Cameras]. Note Under Windows 2000, double click [Scanners and Cameras]. 4. Select [CANON DR-6010C USB] or [CANON DR-6010C SCSI] and click [Properties]. The [CANON DR-6010C USB Properties] or [CANON DR-6010C SCSI Properties] window appears. 3-32...
  • Page 63 Turn the scanner OFF and then ON again. IMPORTANT • If you are using a SCSI connection, turn OFF the computer and then turn the scanner OFF and then ON again. • Wait at least 10 seconds before turning the scanner back ON after it has been turned OFF.

  • Page 64: Multistream Function

    Chapter 3 Basic Operation MultiStream Function If the application that you are using supports the MultiStream function, then it is possible to scan a document once and simultaneously output two types of images (Primary image and Secondary image.) CapturePerfect 3.0 supports the MultiStream function. The following settings are possible. •...

  • Page 65: Chapter4

    Cleaning the Scanner To clean the exterior of the scanner, dampen a cloth with water or a mild detergent, wring the cloth out thoroughly, and then wipe the dirt away. Then use a dry, soft cloth to wipe away any moisture.

  • Page 66: Cleaning The Sensor Glass And The Rollers

    Note The location of the sensor glass and various rollers are shown below. Sensor Glasses Use compressed air to keep the interior of the scanner free of dust and paper particles. Roller Unit Rollers Retard Roller...
  • Page 67 IMPORTANT Scratches on the sensor glass may cause marks on the images and could cause feeding errors. If there are scratches on the sensor glass, contact your local authorized Canon dealer or service representative. Dampen a cloth with water, wring it out thoroughly, and then wipe the rollers of the upper unit while turning them.
  • Page 68 When closing the upper unit, be careful not to get your fingers caught, as this may result in personal injury. IMPORTANT Do not force the upper unit to close. Doing so may damage the scanner. (See “Attaching the Roller Unit,” on p. 4-12.)

  • Page 69: Removing And Attaching The Rollers

    • Be sure to reset the counter after replacing the rollers. p. 4-6.) • For information about the exchange roller kit (roller unit, retard roller,) contact your local authorized Canon dealer or service representative. (See “Resetting the Counter,” on...

  • Page 70: Resetting The Counter

    Chapter 4 Maintenance Resetting the Counter After replacing the feed rollers, open the [Counter setup] dialog box and reset the counter. Open the [Event settings] dialog box. 1. Click [Start] - [Control Panel] to open the Control Panel. Note Under Windows 2000, click the [Start] button and select [Settings] - [Control Panel] to open the Control Panel, then proceed to step 3.
  • Page 71 Chapter 4 Maintenance 3. Click [Scanners and Cameras]. Note Under Windows 2000, double click [Scanners and Cameras]. 4. Select [CANON DR-6010C USB] or [CANON DR-6010C SCSI] and click [Properties]. The [CANON DR-6010C USB Properties] or [CANON DR-6010C SCSI Properties] window appears.
  • Page 72 Chapter 4 Maintenance Click the [Maintenance] tab. Click the [Reset] button, and then make sure that the counter for the roller being used is set to 0.

  • Page 73: Removing/Attaching The Roller Unit

    Chapter 4 Maintenance Removing/Attaching the Roller Unit To remove or attach the roller unit, proceed as follows. CAUTION Use caution when removing or attaching the roller unit. Using too much force may lead to damage or personal injury. Removing the Roller Unit Carefully open the upper unit until it stops.
  • Page 74 Chapter 4 Maintenance Move the roller unit to the right a and then pull it out b. Attaching the Roller Unit Align the cutout on the roller unit with the shaft pin on the main unit. Note If the cutout and pin do not fit, rotate the roller until the parts are properly matched. Slide the roller lock lever to the left and raise the roller unit into position.

  • Page 75: Removing And Attaching The Retard Roller

    When closing the upper unit, be careful not to get your fingers caught, as this may result in personal injury. IMPORTANT Do not force the upper unit to close. Doing so may damage the scanner. Removing and Attaching the Retard Roller To remove or attach the retard roller, proceed as follows.
  • Page 76 Move the roller lock lever down and forward (a,) and then slide it to the right (b.) Shift the retard roller to the right to remove it. Attaching the Retard Roller Position the retard roller so the notch in the roller is facing the scanner’s shaft. 4-12...
  • Page 77 Chapter 4 Maintenance Slide the roller lock lever to the left, and insert it into the retard roller slot. Push the roller lock lever towards the back of the scanner to lock the retard roller into place. Replace the roller cover.
  • Page 78 CAUTION When closing the upper unit, be careful not to get your fingers caught, as this may result in personal injury. IMPORTANT Do not force the upper unit to close. Doing so may damage the scanner. 4-14...
  • Page 79 Chapter 5 5-1 Troubleshooting This section describes the possible problems that might occur during use of the scanner and how to solve them. The Scanner Does Not Turn ON ... The Scanner Is Not Recognized (Connecting via USB)... The PC Does Not Recognize the Scanner (Connecting via SCSI) ...

  • Page 80: Chapter5 Troubleshooting

    Problem The scanner is not ON. Solution Check to see if the scanner is ON. If the scanner is not ON, shut down the PC, then turn the scanner ON first, and then the PC. Problem The SCSI card is not compatible with the scanner.

  • Page 81: Troubleshooting

    Chapter 5 Troubleshooting IMPORTANT • If documents are not scanned normally even if the scanner setup is OK, a probable cause is that the scanner driver or application software is not running correctly. Re-install the scanner driver or application software.

  • Page 82: Saved Image Files Do Not Open

    The rollers inside the scanner are dirty or worn. Solution Clean the rollers, then they need to be replaced. Contact your local authorized Canon dealer or service representative to purchase a roller replacement kit. IMPORTANT The retard roller and roller unit are consumable components. You need to replace the retard roller and roller unit when cleaning does not appear to improve performance.
  • Page 83 Clean the scanning glass and rollers. If lines still appear on the image even after cleaning the scanning glass and rollers, the scanning glass inside the scanner may be scratched. Contact your local authorized Canon dealer or service representative. Symptoms The scanned image is abnormal for certain documents.

  • Page 84: Uninstalling Software

    Chapter 5 Troubleshooting 5-2 Uninstalling Software If the ISIS/TWAIN driver, and “CapturePerfect 3.0” are not operating normally, follow the procedure below to uninstall them. Then, re-install the software from the DR-6010C setup disc. p. 2-4.) IMPORTANT Be sure to log on as an administrator when using Windows 2000 Professional or Windows XP. Click the [Start] button Note For Windows XP, click the [Start] button...

  • Page 85: Uninstalling The Isis/Twain Driver

    “Uninstalling the Job Registration Tool,” on p. 5-8 “Uninstalling CapturePerfect 3.0,” on p. Uninstalling the ISIS/TWAIN Driver From the Programs list in the dialog box, select [Canon DR-6010C Driver] The confirm file deletion screen appears. Click the [Yes] button. click [Uninstall].

  • Page 86: Uninstalling The Job Registration Tool

    Chapter 5 Troubleshooting The uninstall procedure is carried out. After uninstall is complete, click the [Finish] button to exit the uninstaller. Uninstalling the Job Registration Tool From the Programs list in the dialog box, select [DR-6010C Job Tool] and click [Uninstall].
  • Page 87 Chapter 5 Troubleshooting The confirm file deletion screen appears. Click the [Yes] button. Note Under Windows XP, the [Add/Remove Programs] dialog box appears. Click the [Yes] button. The uninstall procedure is carried out. After uninstall is complete, click the [Finish] button to exit the uninstaller.

  • Page 88: Uninstalling Captureperfect 3.0

    Chapter 5 Troubleshooting Uninstalling CapturePerfect 3.0 Select [CapturePerfect 3.0] from the list in the dialog box The file delete confirmation screen appears. Click the [Yes] button. Uninstallation starts. click the [Uninstall] button. 5-10...
  • Page 89 Chapter 5 Troubleshooting After uninstallation is complete, click the [Finish] button to exit the uninstaller. 5-11...

  • Page 90: Chapter6 Appendix

    Secondary Scan Lines) Scanning Speed (A4) Black and White Appendix Desktop sheetfed scanner 2.08" to 8.6" (53 to 219 mm) 2.75" to 14" (70 to 356 mm) 2.75" to 39.3" (70 to 1000 mm) in Long document mode 14 to 32 lb bond (0.0024" to 0.0059") 52 to 128 g/m (0.06 mm to 0.15 mm)

  • Page 91: Replacement Parts

    Kit to replace the roller unit (pickup roller, feed roller) and retard roller. • Refer to “Removing and Attaching the Rollers,” on p. 4-5 • Contact your local authorized Canon dealer or service representative for detailed information about the replacement parts. Options Bar code module (product code: 1922B001) Additional software to allow the ISIS/TWAIN driver to recognize bar codes.

  • Page 92: External Dimensions

    Chapter 6 Appendix External Dimensions 10.9" (278 mm) 21.4" (544 mm) (Document Feed Tray Extension is open) 19.3" (491 mm) (Document Feed Tray is open) 2.0" (51 mm) 12.9" (330 mm) (Document Eject Tray 2 is open) (Document Eject Guide is open)

  • Page 93: Index

    Launcher ... 3-12 Load limit mark ... 3-6 Long Document Mode ... 3-30 Settings ... 3-31 Long document mode ... 3-1 Moving the Scanner ... 1-2 MultiStream Function ... 3-34 Names of Parts ... 1-7 Options ... 6-2 Other Functions ... 3-29 Page Separation Mode ...
  • Page 94 User Manual Software...
  • Page 95 Contents Contents Chapter7 ISIS/TWAIN Driver Settings ...7-1 Before Use ... 7-1 ISIS/TWAIN Driver Properties Dialog Box ...7-3 Basic Tab Sheet ... 7-4 [Brightness] Tab Sheet ...7-13 [Image processing] Tab Sheet...7-17 [Others] Tab Sheet ...7-19 Addon Dialog Box...7-24 Chapter8 Job Registration Tool Settings ... 8-1 Starting the Job Registration Tool...8-1 Job Registration Tool Settings Dialog Box...

  • Page 96: Chapter7 Isis/Twain Driver Settings

    ISIS/TWAIN driver’s Help before making driver settings. 7-1 Before Use This scanner can scan documents ranging in size from business cards and checks to A4 size documents. It can also scan business cards. To use the DR-6010C with an ISIS/TWAIN-compliant application, the DR-6010C must first be selected as the scanner to be used.
  • Page 97 On the [Scan] menu, click [Select Scanner]. Select [Canon DR-6010C] Note If [Canon DR-6010C] is not displayed in the list of scanners, re-install the ISIS/TWAIN driver. Click the [Settings] button to set a default page size. Note • Clicking the [Default] button in the ISIS driver Properties dialog box causes that setting to be applied here.

  • Page 98: Isis/Twain Driver Properties Dialog Box

    Chapter 7 ISIS/TWAIN Driver Settings 7-2 ISIS/TWAIN Driver Properties Dialog Box The ISIS/TWAIN driver properties dialog box consists of four tabs: Basic, Brightness, Image processing and Others. See the description of each tab sheet for details. [OK] Button Applies settings and closes the dialog box. [Scan] Button (TWAIN driver only) To control scanning from the properties dialog box when using a TWAIN-compatible application program, the [Scan] button is displayed instead of the [OK] button to scan with the current settings.

  • Page 99: Basic Tab Sheet

    This [Basic] tab sheet is displayed when the driver is called directly and not from another settings dialog box. The driver is called directly when using applications that do not have their own scanner setting or scanning dialog boxes, such as CapturePerfect and Job Registration Tool.
  • Page 100 Chapter 7 ISIS/TWAIN Driver Settings ☞ Refer to the descriptions of the following function for details about “Skip Blank Page,” “Auto Color Detection,” “Detect Page Size,” “Text Enhanced Enhancement Mode” and “Margin.” • Skip Blank Page • Auto Color Detection •...
  • Page 101 In cases where this may be a problem, try scanning again after cleaning the scanner glass, or select one of the [Advanced Text Enhancement] or [Advanced Text Enhancement II] modes instead.
  • Page 102 Chapter 7 ISIS/TWAIN Driver Settings Mode-Dependent Function Limitations The following tab sheet functions are partially disabled according to the selected mode. Refer to “[Brightness] Tab Sheet,” on p. 7-13 Tab sheet Scanning mode Black and White Error Diffusion Advanced Text Enhancement Advanced Text Enhancement II High-Speed Text Enhancement 256-level Gray...
  • Page 103 Chapter 7 ISIS/TWAIN Driver Settings Dots per inch Select the scanning resolution. ☞ Higher resolutions provide clearer images, but produce larger files. ☞ When the selected resolution is 300 dpi or less, the [Moire Reduction] setting is enabled to allow reduction of Moire patterns in scanned images.
  • Page 104 [24-bit Color], and Scanning Side is set to [Duplex] all at the same time, a portion of the document may not be scanned due to insufficient memory on the scanner. If this occurs, lower the image quality by selecting [Speed priority], or change the Scanning Side setting to [Simplex].
  • Page 105 [24-bit Color], and Scanning Side is set to [Duplex] all at the same time, a portion of the document may not be scanned due to insufficient memory on the scanner. If this occurs, lower the image quality by selecting [Speed priority], or change the Scanning Side setting to [Simplex].
  • Page 106 Chapter 7 ISIS/TWAIN Driver Settings ☞ Changing these settings is not normally necessary. Change them only if you want a document of light colors to be judged to be a black-and-white document. ☞ Select [24-bit Color] if color documents are judged to be black-and-white documents with the default settings.
  • Page 107 Chapter 7 ISIS/TWAIN Driver Settings Scan Area Dialog Box (TWAIN Driver) This dialog box appears with application programs that display the [Scan] button in the Properties dialog box. The Area window and [Preview] button are not displayed when using applications like the Job Registration Tool that display the [OK] button in the Properties dialog box.

  • Page 108: [Brightness] Tab Sheet

    Chapter 7 ISIS/TWAIN Driver Settings ☞ When [Deskew] is enabled on the [Basic] tab sheet, the specified area may be displaced when scanning. Area Window The size indicated for the Area window corresponds to the page size setting, and the area within the panel indicates the current scanning area.
  • Page 109 Chapter 7 ISIS/TWAIN Driver Settings The availability of brightness and contrast settings are as follows according to the mode setting on the [Basic] tab sheet. Scanning mode Black and White Error Diffusion Advanced Text Enhancement Advanced Text Enhancement II High-Speed Text Enhancement 256-level Gray 24-bit Color Auto Color Detection...
  • Page 110 Chapter 7 ISIS/TWAIN Driver Settings [Gamma Settings] Dialog Box Use the [Gamma Settings] dialog box to adjust the gamma correction value. [Custom] Check Box Select this check box to set custom gamma correction. ☞ When [Custom] gamma setting is selected, all settings on the [Brightness] tab sheet are made automatically.
  • Page 111 Chapter 7 ISIS/TWAIN Driver Settings ☞ You can also move the gamma curve by dragging it with the mouse. [Freehand] The output value for a particular input value in the gamma table can be specified with the mouse. ☞ Click any point in the Gamma Curve Graph to set that point as an output value. ☞...

  • Page 112: [Image Processing] Tab Sheet

    Chapter 7 ISIS/TWAIN Driver Settings [Image processing] Tab Sheet The [Image processing] tab sheet provides settings affecting processing of scanned images. Some settings may be disabled depending on the mode settings on the [Basic] tab sheet. Refer to Dependent Function Limitations,” on p. 7-7 [Edge Emphasis] Adjusts image contours.
  • Page 113 Chapter 7 ISIS/TWAIN Driver Settings [Text Orientation Recognition] Check Box Select this check box to detect text orientation in scanned images, and rotate images in 90º increments as needed to normalize orientation. ☞ When [Text Orientation Recognition] is selected, [Image Rotation] and area settings in the Scan Area dialog box are disabled.

  • Page 114: [Others] Tab Sheet

    Chapter 7 ISIS/TWAIN Driver Settings ☞ The color range within the shaded (cross-hatched) area is dropped out or enhanced. ☞ You can move the shaded area by dragging with the mouse. ☞ You can change the specified color range by dragging the edges of the shaded area. ☞...
  • Page 115 ☞ JPEG transfer is good for color and grayscale images, as scanned image data is JPEG- compressed within the scanner before output. This reduces the size of the image data for output, so transfer time from the scanner to the computer is shortened.
  • Page 116 This feeding method is good for scanning batches of documents of different sizes: after loading the documents, press the Job button (assigned as a Start button on the scanner) to start scanning, and press the assigned Stop button to stop scanning.
  • Page 117 Chapter 7 ISIS/TWAIN Driver Settings With the [Standard Feeding] Feeding Option With the [Automatic Feeding] or [Panel Feeding] Feeding Option [Auto] Each batch of documents is saved with different file names. [Panel] Document batches are separated when the [Batch Separation] button on the Scan Panel is pressed. (See “Scan Panel,”...
  • Page 118 Chapter 7 ISIS/TWAIN Driver Settings [Barcodes] Button This is enabled when the optional barcode module is installed: click it to open the Barcode dialog box and make settings affecting barcode detection in documents. For details, see the ISIS/TWAIN driver Help, or contact your supplier. [Addon] Button This button opens the [Addon] dialog box, where you can make setting for adding text or bitmap images to scanned document images.

  • Page 119: Addon Dialog Box

    Chapter 7 ISIS/TWAIN Driver Settings Addon Dialog Box The [Addon] dialog box provides access to the following dialog boxes, where you can make setting for adding text or bitmap images to scanned document images. The [Addon] dialog box enables you to make setting for adding text or bitmap images to scanned document images.
  • Page 120 Chapter 7 ISIS/TWAIN Driver Settings [Addon] Check Box Select this check box to apply text or bitmap images to scanned document images. Imprinter Side Select the side on which to apply your text or images. [Enable] Check Box Select this check box to enable the application of add-on text. Text Enter the text string to be applied.
  • Page 121 Chapter 7 ISIS/TWAIN Driver Settings [Down arrow] abbreviation: <D> Inserts a down arrow ( ) symbol. [Left arrow] abbreviation: <L> Inserts a left arrow () symbol. [Right arrow] abbreviation: <R> Inserts a right arrow ( ) symbol. ☞ Special text can only be entered for one type of counter. If entered for two counter types, the Preview panel displays an error message.
  • Page 122 Chapter 7 ISIS/TWAIN Driver Settings ☞ When add-on text is applied to an image, the size of the characters depends on the scan resolution. [Enable] Check Box Select this check box to enable application of bitmap images to scanned images. ☞...
  • Page 123 Chapter 7 ISIS/TWAIN Driver Settings [Horizontal Offset] Enter the desired offset from the edge of the document feeder inlet. ☞ When applying an add-on to the front side, enter the offset from the left side of the feeder inlet. ☞ When applying an add-on to the back side, enter the offset from the right side of the feeder inlet. ☞...
  • Page 124 Chapter 7 ISIS/TWAIN Driver Settings Start Value Enter the start value for the counter. Increment This is the counter increment value. The counter increments by the value entered here. Increment Trigger Specifies the type of event that triggers a counter increment. [New File] (ISIS driver only) The counter increments when a batch separation occurs according to the Batch Separation settings on the [Others] tab sheet.

  • Page 125: Chapter8 Job Registration Tool Settings

    Chapter 8 Job Registration Tool Settings This chapter describes Job Registration Tool settings for job functions. Refer to Section Function,” on p. 3-9 for details. 8-1 Starting the Job Registration Tool The Job Registration Tool is a TWAIN-compliant application program that installs with the ISIS/ TWAIN driver, and is started by the following procedure.

  • Page 126: Job Registration Tool Settings Dialog Box

    [Admin] dialog box, and the New/Edit dialog box provides access to function setting dialog boxes. (See “[New/Editing] Dialog Box,” on p. 8-4.) Job Registration Tool Dialog Box 8-3) [New/Editing] Dialog Box Access Setting [Admin] Dialog Box 8-4) Scanner Settings Dialog Box PDF/TIFF Settings 8-8)

  • Page 127: Job Registration Tool Dialog Box

    This dialog box appears when the Job Registration Tool is started from the Programs menu. Job Button Settings List The displayed job buttons correspond to those on the scanner, showing their currently assigned settings. Clicking on the job buttons (a, b and c) opens the New/Editing dialog box.

  • Page 128: [New/Editing] Dialog Box

    Chapter 8 Job Registration Tool Settings [New/Editing] Dialog Box The [New/Editing] dialog box appears when you click a Job button in the Job Registration Tool dialog box. The [New/Editing] dialog box appears as follows depending on the function settings registered to the Job buttons.
  • Page 129 (See “About Launcher,” on p. 3-12.) Scanner setting When the “Save as file,” “Print” or “Attach to E-mail” function is selected, Scanner settings are enabled, and you can press the [Setting] button to make scanner settings. ☞ Refer to Chapter 7, “ISIS/TWAIN Driver Settings”...
  • Page 130 ☞ Selecting [TIFF] or [PDF] enables the [Setting] button. ☞ When the [Auto Color Detection] scanner setting is selected, an error is displayed if [JPEG] is selected when you click the [OK] button. If this error appears, select another file format or change the scanner setting.
  • Page 131 • Select [High Compression] to save files with high compression. Although file size is reduced, image quality may be slightly degraded. ☞ The Compression rate setting is enabled when the scanner is set to [256-level Gray] or [24-bit Color] mode. When [Black and White] or [Error Diffusion] binary image scanning mode is selected, file size depends on the content of the scanned document.

  • Page 132: Administration Dialog Box

    Chapter 8 Job Registration Tool Settings Setting to Print Scanned Images (Function: Print) [Printer] Shows the printer to use for printing images. Click the [Printer setting] button to change printer settings. [Print format] Select whether to resize images for printing. •...
  • Page 133 Chapter 8 Job Registration Tool Settings Settings for Monitoring the Folder for Saved Images [Capacity Warning Settings] The Capacity Warning Settings allow you to specify in advance the folder for saving image files, and the space to be available for saving files. If the space required to save a file would exceed the specified Warning Size when starting to scan or while scanning, a warning message appears.
  • Page 134 Chapter 8 Job Registration Tool Settings ☞ The maximum size of attached files must not exceed the limit determined by the mail server. Ask your e-mail system administrator for the attachment size limit of the mail server. [Back Up / Restore] Settings [Back Up] Button Writes a backup file (*.reg) of registered job data to the specified folder.

  • Page 135: Chapter9 Practical Examples

    Chapter 9 This chapter provides examples of settings for the DR-6010C ISIS/TWAIN driver. Refer to these examples when making ISIS/TWAIN driver settings. For descriptions of particular setting items, “ISIS/TWAIN Driver Settings,” on p. Scanning Both Sides of Pages • To scanning both sides of pages Select [Duplex] for the Scanning Side setting on the [Basic] tab sheet.

  • Page 136: Adjusting The Scan Area

    [Auto-detection] is selected as the [Page Size]. on p. 7-11.) With the TWAIN driver, load a document in the scanner and click the [Preview] button to scan one page.) The scanned image is displayed in the Area window so that you can adjust the scan area while viewing the preview image.

  • Page 137: Scanning Multiple Documents

    Set the [Feeding Option] on the [Basic] tab sheet to either [Automatic Feeding] or [Panel Feeding]. (See “Feeding Option,” on p. 7-21.) When [Automatic Feeding] is selected as the [Feeding Option], the scanner detects documents and starts scanning as they are loaded, so continuous scanning is available just by loading the document batches repeatedly.

  • Page 138: Image Adjustments For Scanning

    Set the [Feeding Option] to either [Automatic Feeding] or [Panel Feeding], and scan each page. After scanning each page, the scanner returns to the waiting state. When [Automatic Feeding] is selected as the [Feeding Option], the scanner detects documents and starts scanning as they are loaded.
  • Page 139 Chapter 9 Practical Examples Scanned images are rotated as follows according to the orientation of loaded documents and the selected angle. Feeder documents: face up Image rotation (clockwise) Flatbed documents: face down • To rotate images to match document text Select [Text Orientation Recognition] on the [Image processing] tab sheet.
  • Page 140 Chapter 9 Practical Examples • To skip or enhance a custom color Select [Drop-out color Custom] or [Custom color Enhance] in the [Color drop-out] list on the [Image processing] tab sheet to open the [Color Settings] dialog box. Here you can specify the range of colors to be dropped out or enhanced.

  • Page 141: Prescan

    Chapter 9 Practical Examples Prescan • To confirm images before scanning Select the [Prescan] check box on the [Others] tab sheet, and scan. When scanning is first started, the first document page is prescanned and displayed in the Prescan panel. •...
  • Page 142 CANON ELECTRONICS INC. 1248, SHIMOKAGEMORI, CHICHIBU-SHI, SAITAMA 369-1892, JAPAN CANON U.S.A. INC. ONE CANON PLAZA, LAKE SUCCESS, N.Y. 11042, U.S.A. CANON CANADA INC. 6390 DIXIE ROAD, MISSISSAUGA, ONTARIO L5T 1P7, CANADA CANON EUROPA N.V. BOVENKERKERWEG 59-61, P.O.BOX 2262, 1180 EG AMSTELVEEN, THE NETHERLANDS CANON LATIN AMERICA, INC.

This manual is also suitable for:

3801b002Imageformula dr-6010c

Table of Contents