Floor Standing-Type Air Conditioner OWNER'S MANUAL MODELS: LG-BKE 9300 D Prior to installation, this air-conditioning unit must be submitted for approval by the utility service which provides electricity (EN 61000-3 Norm). IMPORTANT • Please read this owner's manual carefully and thoroughly before installing and operating your air conditioner.
Page 2
Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner. You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all.
Safety Precautions To prevent injury to the user or other people and property damage, the following instructions must be followed. I Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications. WARNING CAUTION I Meanings of symbols used in this manual are as shown below.
Page 4
Authorized Service Center. • There is risk of fire, electric shock, explosion, or injury. Do not let the air conditioner run for a long time when the humidity is very high and a door or a window is left open.
Page 5
Do not allow water to run into electric parts. • It may cause There is risk of fire, failure of the product, or electric shock. When flammable gas leaks, turn off the gas and open a window for ventilation before turn the product on. •...
Page 6
(Don't sit in the draft.) • This could harm to your health. 6 Floor Standing-Type Air Conditioner Take care to ensure that nobody could step on or fall onto the outdoor unit. • This could result in personal injury and product damage.
Page 7
Always insert the filter securely. Clean the filter every two weeks or more often if necessary. • A dirty filter reduces the efficiency of the air conditioner and could cause product malfunction or damage. Use a firm stool or ladder when cleaning or maintaining the product.
4. Whisper quiet operation 5. Wireless remote control Air Outlet Vent Remote Signal Receptor Air Intake Vent 8 Floor Standing-Type Air Conditioner 6. 2 cooling/heating speeds 7. Removable air filter 8. Anti-Bacteria filter 9. 3 minutes delay circuit Air Intake Vent...
Page 9
Operating Instructions Indoor Unit Controls and Indicators A/CL Owner's Manual 9...
Page 10
FAN OPERATION LAMP 7. COOLING OPERATION LAMP 8. SOFT DRY OPERATION LAMP 9. HEATING OPERATION LAMP 10 Floor Standing-Type Air Conditioner 10. DEFROST OPERATION LAMP 11. OFF TIMER OPERATION LAMP 12. OUTDOOR UNIT OPERATION LAMP 13. ELECTRIC HEATER OPERATION LAMP...
Page 11
Remote-Controller for MODEL A/CL Operating Instructions Owner's Manual 11...
Page 12
Operating Instructions Name and Function-Remote Control 1. Signal Transmitter • Transmits the signals to the floor standing type air conditioner 2. Operation Display of the Remote Control 3. Indoor Fan Speed Selection Button • To select the desired fan speed in two steps [Low, Mid] 4.
Remote Control Preparation 1. How to mount onto a wall Use the screws to secure the holder to the wall or attach the holder side of indoor unit. To insert the remote control to the holder. Insert How to insert batteries 1.
Page 14
• Each time the Operation Mode Selection Button is pressed, the Operation Mode is shifted in the arrow direction. How to use the Fan speed Button • Each time the Fan speed Button is pressed, the Fan speed is shifted in the arrow direction. 14 Floor Standing-Type Air Conditioner Cooling Operation Soft Dry Operation...
Cooling Operation Mode Press the Start/Stop Button. Select Cooling Operation. Press the Operation Mode Selection Button. Press the Cooling Operation Button on the remote controller. Set the temperature lower than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. Set the Fan Speed.
The temperature can be set within a range of 16°C~30°C by 1°C. During softy Dry Operation • The indoor fan speed is automatically set to low and can be set fan speed. 16 Floor Standing-Type Air Conditioner A/CL To raise the temperature...
Page 17
Heating Operation Mode(Heat Pump Model) Press the Start/Stop Button. Select heating Operation. Press the Operation Mode Selection Button. Press the heating Operation Button on the remote controller. Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C. Set the Fan Speed.
Page 18
To lower the temperature. (When you feel too warm or hot) During Auto Operation • It is impossible to switch the indoor fan speed because of being already set to the best conditioner by fuzzy rule. 18 Floor Standing-Type Air Conditioner A/CL by 1 level. Cold...
Page 19
Electric Heater Operation Mode(Heat pump & Electric heater product only) Press the Start/Stop Button. Select heating Operation by pressing the Opertion Mode Selection button. Press the Heater Operation Button on the remote controller. Set the temperature upper than the room temperature. The temperature can be set within a range of 16°C~30°C by 1°C.
• If you select ‘ ’, the Off Timer function will be cancelled. When you finish the Off Timer setting, the Timer indicator lights off. During off-timer operation if you press the Timer Button, the rest time will be displayed. 20 Floor Standing-Type Air Conditioner A/CL After 4 seconds...
Page 21
Plasma Air Purifying Operation Procedure Air Purifying Operation only Press the Plasma Air Purifying Operation Start/Stop Button. (Operation will start when the button is pressed, and stop when the button is pressed again.) Select Fan speed. The display shows low fan speed at the initial condition. •...
Press the Start/Stop Button. (Operation will start when the button is pressed, and stop when the button is pressed again.) 22 Floor Standing-Type Air Conditioner Press Fan Operation Button. ❑ Each time the Button is pressed, the Fan Speed mode is shifted.
Jet Cool Operation Press the Start/Stop Button. On/Off Press the Jet Cool button to operate the speed cooling mode and the unit will operate in high fan speed on cooling mode. To cancel the Jet Cool mode, press the Jet Cool button again or the fan speed button or the room temperature setting button and the unit will operate in mid fan speed on cooling mode.
Auto restart In case the power comes on again after a power failure, Auto Restarting Operation is the function to operate procedures automatically to the previous operating conditions. 24 Floor Standing-Type Air Conditioner After 3 second, After 3 seconds, it will shift...
Cleaning of the air conditioner • Don’t wash with water. • Wipe with a soft dry cloth. When the air conditioner is not going to be used for a long time. At the end of the season Operate the air conditioner at the following settings for 2 to 3 hours.
• Condensation occurs when the airflow from the air conditioner cools the warm room air. • This is the Protection device of the air conditioner . • Wait about three minutes and operation will begin. • If the airflow begins before its temperature become warm, it will cause an undesired cooling effect.