1. Manuals
  2. Brands
  3. Frigidaire Manuals
  4. Laundry Appliance
  5. GLET1142CS0
  6. Installation instructions manual

Frigidaire GLET1142CS0 Installation Instructions Manual

Full size laundry center gas & electric
Hide thumbs Also See for GLET1142CS0:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual , Operating Instructions
Before beginning installation, carefully read these instructions. This will simplify the installation
and ensure the laundry center is installed correctly and safely. Leave these instructions near the
laundry center after installation for future reference.
NOTE:
The electrical service to the laundry center must conform with local codes and ordinances
and the latest edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian
Electrical Code, CSA C22.1
NOTE:
The gas service to the laundry center must conform with local codes and ordinances and
the latest edition of the National Fuel Gas Code ANSI Z223.1/NFPA 54, or in Canada, the Canadian
Natural Gas and Propane Installation Code, CSA B149.1.
NOTE:
T
he laundry center is designed under ANSI Z21.5.1 or ANSI/UL 2158- CAN/CSA C22.2
(latest edition) for HOME USE only. This laundry center is not recommended for commercial
applications such as restaurants or beauty salons, etc.
For your safety the information in
this manual must be followed to minimize the risk
of fire or explosion or to prevent property damage,
personal injury or loss of life.
- Do not store or use gasoline or other flammable
vapors and liquid in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
Do not try to light any appliance.
Do not touch any electrical switch; do not use
any phone in your building.
Clear the room, building or area of all
occupants.
Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call the
fire department.
Installation and service must be preformed by a
qualified installer, service agency or the gas
supplier.
Printed in U.S.A.
Installation
Instructions
Full Size Laundry Center
Contents
SUBJECT
Gas & Electric
PAGE
2
2
2
2
3
4
4
4
5
5
6
6
7
7
8
P/N131661700 (0110)

Advertisement

Table of Contents
loading

Related Manuals for Frigidaire GLET1142CS0

Summary of Contents for Frigidaire GLET1142CS0

  • Page 1: Table Of Contents

    Before beginning installation, carefully read these instructions. This will simplify the installation and ensure the laundry center is installed correctly and safely. Leave these instructions near the laundry center after installation for future reference. NOTE: The electrical service to the laundry center must conform with local codes and ordinances and the latest edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian Electrical Code, CSA C22.1 NOTE:...

  • Page 2: Pre-Installation Requirements

    8. Pipe thread sealer (Gas). 9. Ratchet with 3/8 inch (0.96 cm) socket. ELECTRICAL REQUIREMENTS ELECTRIC Laundry Center Circuit- Individual 30 amp branch circuit fused with 30 amp minimum time delay fuses or circuit breakers. POWER SUPPLY - 3-wire or 4-wire , 240 volt, single phase, 60 Hz, Alternating Current.

  • Page 3: Exhaust System Requirements

    EXHAUST SYSTEM REQUIREMENTS Use only 4 inch (10.16 cm) diameter (minimum) rigid or flexible metal duct and approved vent hood which has a swing-out damper(s) that opens when the dryer is in operation. When the dryer stops, the damper(s) automatically closes to prevent drafts and the entrance of insects and rodents.

  • Page 4: Gas Supply Requirements

    GAS SUPPLY REQUIREMENTS 1. Installation MUST conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 (latest edition) or in Canada, the current AN/CGA B149. 2. The gas supply line should be of 1/2 inch (1.27 cm) pipe. 3.

  • Page 5: Rough-Ln Dimensions

    ROUGH-IN DIMENSIONS 12 ½ IN. (31.75 CM) VENT 75 ½ IN. (191.77 CM) ELECTRICAL CONNECTION 54 5/16 IN. WATER INLETS (137.95 CM) (REAR) 43 IN. (109.22 CM) DRAIN OUTLET (REAR) 3 ¾ IN. (9.52 CM) 27 IN. (68.58CM) UNPACKING 1. Using the four shipping carton corner posts (two on each side), carefully lay the laundry center on its left side and remove foam shipping base.

  • Page 6: Electrical Installation

    240 volt power supply. GROUNDING REQUIREMENTS Non-Canadian ELECTRIC Laundry Center Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded.

  • Page 7: 4-Wire Connections

    ELECTRICAL CONNECTIONS FOR A 3-WIRE SYSTEM ELECTRIC Laundry Center 1. Remove the screw securing the terminal block access cover to the rear panel and remove cover. 2. Install a U.L. approved strain relief connector in the entry hole on the back panel.

  • Page 8: Replacement Parts

    7. GAS CONNECTION (Gas laundry centers only) a. Remove the shipping cap from gas pipe at the rear of the dryer. NOTE: DO NOT connect the laundry center to L.P. gas service without converting the gas valve. An L.P. conversion kit (P/ N 5303937053) must be installed by a qualified gas technician.

Table of Contents