Download Print this page

Frigidaire GLTF530DS0 Tech Sheet

Retain for service technician

Advertisement

Quick Links

TECH SHEET - RETAIN FOR SERVICE TECHNICIAN
Timer/off
Drawer/open
Door/open
LINE SWITCH
PUSH-PULL
BLK/WHT
BLK
L1
#4
0T
0C
1
DISPENSER
DRAWER
BLEACH
REED SWITCH
2
#5
4.4
DOOR
LOCK
COIL
2.1
DOOR
LAMP
2
BLEACH
1
N
GRN
GND
Motor Will Not Run
1.
CHECK FOR POWER:
Advance the timer knob to the drain
increment. If the drain pump does not run,
check household safety circuit. If the drain
pump runs go to step 2.
2.
CHECK FOR MOTOR MOVEMENT:
Turn the water off to the washer. Remove
electrical power from the washer and
remove the back panel. Remove the motor
drive belt. Reconnect electrical power and
set the timer to the start of the Regular wash
cycle and pull the knob out. If motor does
not rotate, check for a poor connection in the
timer line switch or door lock switch. If good,
and moto r does not run go to step 3.
3.
MEASURE VOLTAGES:
Remove the six pin plug from the speed
control unit. Measure the voltage between
pins 5 and 6 on the harness. If the meter
reads 0 check the connection in the timer
line switch or door lock. If the meter
reads 120 Vac go to step 4.
6
1

IMPORTANT SAFETY NOTICE

This information is intended for use by technicians possessing
adequate background of electrical, electronic and mechanical
experience. Any attempt to repair a major appliance may result in
personal injury and property damage. The manufacturer or seller
cannot be responsible for the interpretation of this information, nor
can it assume any liability in connection with its use.
Disconnect from Electrical Supply Before Servicing Washer.

WIRING DIAGRAM

2.2
4.3
DOOR
1
LOCK
SWITCH
TAN/BLK
2
3
WATER LEVEL
PRESSURE
SWITCH
TAN
2
SOFTENER
2B
B
4
T
RINSE
WATER
B
COLD
WHT
SOFTENER
DISPENSER
VALVES
CABINET
CHASSIS
4.Set the timer to the Heavy Wash position of
the Regular wash cycle. Remove the ten pin
plug from the speed control unit. Measure
the voltage between pins 1, 2, 6 and 10 of
the ten pin plug to pin 5 of the 6 pin plug on
the harness. The voltage at pins 2, 6, and
10 should read 120 Vac and 0 Vac at pin 1.
If not, check timer contacts 1C to 1B, 5C to
5B, and 7C to 7B for closed contacts, and
3C to 3B for open contacts. If the voltage
readings are correct, go to step 5.
5
6
1
1
5.
MEASURE RESISTANCES:
Check the fuse on the speed control board.
If the fuse is open, replace the speed control
board. If good, go to step 6.
6.Remove the 6 pin plug from the sp
control unit. Measure the resistance
Speed
between pins 1 and 2, 2 and 3, and 3 and 1
Control
of the speed control unit. If the meter reads
other than 3 Meg ohms ± 10%, replace the
speed control board.
BLK/RED
#6
AQUA
WASH
WATER
8
T
RINSE
WASH
WATER
WATER
SWITCH
T
10
B
3
5
2
1
4
TEMP
SWITCH
WATER
HOT
+t
VALVES
MOTOR
#1
WHT
10
Speed
6
Control
eed
If grounding wires, screws or clips used to complete a path to ground are removed
for service, they must be returned to their original position and properly fastened.
Certain internal parts are intentionally NOT grounded and may present a risk of
electric shock only during servicing. Do not contact the following parts while the
appliance is energized: pump, drive motor and electronic control boards.
YEL/BLK
TIMER
DIRECT
CYCLE
SIGNAL
T 12 B
T
14
B
EXTRA
RINSE
MS
TIMER
SIGNAL
MOTOR
PINK
#2
1
6C
M
6T
2
WAX
PUMP
MOTOR
#3
WHT
#7
WHT
7.Remove electrical power from the washer.
With an ohmmeter check the resistance
between pins 1 and 2, 2 and 3, and 3 and 1
of the six pin plug on the harness. If the
meter reads other than 2.6 ohms ± 7%,
replace the motor.
6
1
Quick Facts
•The timer motor will not run continuously.
The speed control unit controls the timer
motor and advances the timer when needed.
•In some tumble modes, the tub may not
tumble for the first 16 to 20 seconds after
start-up.
•Extremely low water pressure may cause
tub rotation to stop until WLC satisfied.
IMPORTANT
1C
3C
5C
7C
1B
3B
5B
7B
MOTOR CONTROL
6
3
4
2
1
5
MOTOR
WINDING
T
TACHO-
GENERATOR
WATER TEMP SWITCH
SWITCH
CIRCUIT
POSITION
W/R
1 - 3
1 - 5
2 - 4
H/C
X
W/C
X
X
C/C
X
W/W
X
X
X
*
Not on all models
*
Speed
Control
134390200
0402

Advertisement

loading

Summary of Contents for Frigidaire GLTF530DS0

  • Page 1: Wiring Diagram

    If the drain pump runs go to step 2. CHECK FOR MOTOR MOVEMENT: Turn the water off to the washer. Remove electrical power from the washer and remove the back panel. Remove the motor drive belt. Reconnect electrical power and set the timer to the start of the Regular wash cycle and pull the knob out.
  • Page 2 DOOR LAMP WON'T LIGHT OR DOOR LOCK SOLENOID WON'T ENERGIZE TIMER DISPENSER DRAWER REED SWITCH IF NO END-OF-CYCLE SIGNAL (BUZZER) TIMER DOOR TIMER LOCK IF DOOR LOCK OPENS DURING SPIN TIMER DOOR TIMER LOCK IF TIMER WON'T ADVANCE TIMER TIMER DOOR LOCK IF WATER PUMP DOES NOT WORK...