Canon PIXMA MP495 Installation Manual
  1. Manuals
  2. Brands
  3. Canon Manuals
  4. All in One Printer
  5. PIXMA MP495 Series
  6. Installation manual

Canon PIXMA MP495 Installation Manual

Installing your multifunction to your network for the first time
Hide thumbs Also See for PIXMA MP495:

Advertisement

Table of Contents

See also: Network Manual
Next >>
<< Previous
Installing Your Multifunction
to Your Network for the First Time
PIXMA MP495
Mac OS
1

Advertisement

Table of Contents
loading

Related Manuals for Canon PIXMA MP495

Summary of Contents for Canon PIXMA MP495

  • Page 1 Next >> << Previous Installing Your Multifunction to Your Network for the First Time PIXMA MP495 Mac OS...
  • Page 2 Installing Your Multifunction to Your Network for the First Time Preparing to Connect My Multifunction to My Network Network Requirements Notes on Wireless Connection Installing the Drivers & Software Registering the Printer & Scanner PIXMA MP495 Mac OS << Previous Next >>...

  • Page 3: Network Requirements

    Preparing to Connect My Multifunction To My Network Network Requirements Before connecting the machine to the network, make sure that configuration of the computer and access point or router is complete, and that the computer is connected to the network. Wireless Connection Before connecting the machine to the network, the computer needs to be connected to the network.
  • Page 4 Preparing to Connect My Multifunction To My Network Notes on Network Connection The configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment. For details, refer to your device's instruction manual or contact its manufacturer. The machine cannot be used over a wireless and wired connection at the same time.

  • Page 5: Software Installation

    Setup CD-ROM during restarting. The installation resumes once your computer has restarted. • If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network. If such a warning message appears, set the security software to always allow access.
  • Page 6 Installing the Drivers & Software Software Installation Do not connect the wireless LAN setup cable yet. Software installation requires temporary use of the wireless LAN setup cable. Step One Turn on the computer, then insert the Setup CD- ROM into the CD-ROM drive. <<...
  • Page 7 Installing the Drivers & Software Step Three Enter your administrator name and password. Click OK. If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop. If you do not know your administrator name or password, click Help , then follow the on-screen instructions.
  • Page 8 Installing the Drivers & Software Step Five Select Use the printer on network, then click Next. Follow any on-screen instructions to proceed with the software installation. << Previous Step Six When the Printer Detection screen appears, click Next. IMPORTANT If the Printer Connection screen appears instead of the screen above, the connection method is not correctly selected in 5.
  • Page 9 Installing the Drivers & Software Step Seven Make sure the machine is turned on, then click OK. << Previous Step Eight When the Set Up New Printer screen appears, click Next. Note: If the Detected Printers List screen appears, click Set Up New Printer. Next >>...
  • Page 10 Installing the Drivers & Software << Previous Next >> Step Nine When the Connect Cable screen appears, connect the machine to the computer with the wireless LAN setup cable. Follow the on-screen instructions and click Next.
  • Page 11 Installing the Drivers & Software Step Ten 10-A If the Detected Access Points List screen appears: If the screen below does not appear, perform 10-B. << Previous 1. Select the target access point name/network name (SSID). 2. Enter the network key. Enter upper and lower case letters of the alphabet correctly.
  • Page 12 Installing the Drivers & Software Step Ten 10-B If the Confirm Connection Access Point screen appears. << Previous Make sure that the target access point is displayed, then click Yes. If a screen asking for permission to access the keychain appears, click Allow or Allow Once.
  • Page 13 Installing the Drivers & Software Step Eleven When the Disconnect Cable screen appears, remove the wireless LAN setup cable, then click Next. << Previous Step Twelve Click Complete or OK on the Setup Completion screen. Next >>...
  • Page 14 This section describes how to register the machine on a Macintosh computer. Note: The alphanumeric characters after Canon MP495 series is the machine's Bonjour service name or MAC address. If the machine has not been detected, make sure of the following.
  • Page 15 Registering the Printer & Scanner Step One When the Register Printer and Scanner screen appears, click Register Printer. << Previous Proceed to the section that relates to your operating system for further installation instructions Mac OS X v. 10.5.x / 10.6.x: Go to Step 2-A Mac OS X v.
  • Page 16 Registering the Printer & Scanner Step Two Select Canon MP495 series canonijnetwork and click Add. << Previous Step Two 1. When the Printer List window appears, click Add. Note: When the You have no printers available. screen appears, click Add.
  • Page 17 Registering the Printer & Scanner Step Two 2. Click More Printers in the Printer Browser window. << Previous Step Two 3. Select Canon IJ Network in the pop-up menu, select Canon MP495 series in the list of printers, then click Add. Next >>...
  • Page 18 Registering the Printer & Scanner Step Two 4. Make sure that Canon MP495 series is added to the list of printers. Go to Step Three. << Previous Step Three When the Register Printer and Scanner screen appears, click Register Scanner.
  • Page 19 Registering the Printer & Scanner Step Four Select Canon MXxxx series on the Scan-from-PC Settings screen, then click OK.. *xxx refers to the model number. << Previous Step Five Click Next on the Register Printer and Scanner screen. Wireless setup is now complete.
  • Page 20 Registering the Printer & Scanner Step Six Click Next on the Print Head Alignment Recommended screen. << Previous Step Seven Click Next on the Register Printer and Scanner screen. Next >>...
  • Page 21 Registering the Printer & Scanner Step Eight If the User Registration screen appears, read the information and click Next or Cancel. << Previous If the Extended Survey Program screen appears: If you can agree to Extended Survey Program, click Agree. If you click Do not agree, the Extended Survey Program will not be installed.

  • Page 22: Registering Printer & Scanner

    Registering the Printer & Scanner << Previous Step Nine Click Exit. Setup is complete *It is necessary to restart the computer before scanning using the Operation Panel on the machine for the first time.

Table of Contents