Frigidaire FCS367FCB Service Data Sheet

Dual fuel slide-in range with electronic oven control gas slide-in range with electronic oven control
Hide thumbs Also See for FCS367FCB:

Advertisement

SERVICE DATA SHEET
Dual Fuel Slide-in Range with Electronic Oven Control
Gas Slide-in Range with Electronic Oven Control
NOTICE
°
This service data sheet is intended for use by persons having electrical and mechanical training and a level of
knowledge of these subjects generally considered acceptable in the appliance repair trade. The manufacturer
cannot be responsible, nor assume any liability, for injury or damage of any kind arising from the use of
this data sheet.
SAFE SERVICING PRACTICES
.
To avoid the possibility of personal injury and/or property damage, it is important that safe servicing practices be
observed. The following are examples of some, but not all, of these practices.
1. Do not attempt a product repair if you have any doubts as to your ability to complete it in a safe and satisfactory
manner.
2. Before servicing or moving an appliance, remove power cord from electric outlet, trip circuit breaker to OFF, or
remove fuse and turn off gas supply.
3. Never interfere with the proper installation of any safety device.
4. USE ONLY REPLACEMENT PARTS CATALOGED FOR THIS APPLIANCE. SUBSTITUTIONS MAY DEFEAT COMPLIANCE
WITH SAFETY STANDARDS SET FOR HOME APPLIANCES.
5. GROUNDING: The standard color coding for safety ground wires is GREEN OR GREEN WITH YELLOW STRIPES.
Ground leads are not to be used as current carrying conductors. IT IS EXTREMELY IMPORTANT THAT THE SERVICE
TECHNICIAN REESTABLISH ALL SAFETY GROUNDS PRIOR TO COMPLETION OF SERVICE. FAILURE TO DO SO
WILL CREATE A POTENTIAL HAZARD.
6. Prior to returning the product to service, ensure that:
• All electric connections are correct and secure.
• All electrical leads are properly dressed and secured away from sharp edges, high-temperature components,
and moving parts.
• All non-insulated electrical terminals, connectors, heaters, etc. are adequately spaced away from all metal
parts and panels.
• All safety grounds (both internal and external) are correctly and securely reassembled.
• All panels are properly and securely reassembled.
318127022 (0505) Rev. A
1

Advertisement

Table of Contents
loading

Summary of Contents for Frigidaire FCS367FCB

  • Page 1 SERVICE DATA SHEET Dual Fuel Slide-in Range with Electronic Oven Control Gas Slide-in Range with Electronic Oven Control NOTICE ° This service data sheet is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. The manufacturer cannot be responsible, nor assume any liability, for injury or damage of any kind arising from the use of this data sheet.
  • Page 2: Electronic Oven Control

    ELECTRONIC OVEN CONTROL 1. This self-cleaning controller offers Bake, Broil, Speed Bake (some models) modes, Timed and Delayed Baking, and Cleaning functions. 2. This Controller has a touch sensitive membrane. Speed Speed Bake clean bake Keep Broil Clean warm NOTE: The Controller's are not field repairable. Only temperature settings can be changed. See oven calibration. Speed Bake Oven Bake time...
  • Page 3: Oven Calibration

    SPEED BAKE MODE (some models) The speed bake oven uses the addition of a fan to move the air already in the oven. Moving the heated air helps to destratify the heat and cause uniform heat distribution. Cooking times can be reduced by as much as 30%. The air is drawn in through a fan shroud located on the rear wall of the oven.
  • Page 4 ELECTRONIC OVEN CONTROL ELECTRONIC OVEN CONTROL (EOC) FAULT CODE DESCRIPTIONS AND RTD SCALE Note: Only three fault codes series are displayed by this control “F1”, "F3" and “F9”. Generally speaking “F1” implies a control failure, “F3” an oven probe problem, and “F9” a latch motor problem. In all occurrences the alarm is accompanied by a display of “F1“.
  • Page 5 RTD SCALE Temp. °F Temp. °C 32 ± 1.9 0.0 ± 1.1 75 ± 2.5 23.9 ± 1.4 250 ± 4.4 121.1 ± 2.4 350 ± 5.4 176.7 ± 3.0 450 ± 6.9 232.2 ± 3.8 550 ± 8.2 287.8 ± 4.6 650 ±...
  • Page 6: Fan Blade

    EXPLODED VIEW OF SPEED BAKE SYSTEM (some models) Speed Bake Fan Motor Assembly FAN BLADE The fan blade is mounted in the rear of the unit and has a "D" shaped mounting hole. Only minimum clearance exists between the oven back, fan blade, and fan shroud. Be careful not to bend blade when removing or installing. Access to the fan blade is gained by removing the fan shroud, held in place by three screws, from the inside of the oven.
  • Page 7: Fan Relay

    FAN RELAY The fan motor runs continuously while in the speed bake mode unless the door is opened. If the fan does not operate, check the following: • Display illuminated on the electronic control. • Voltage output between terminals P5-3 and Neutral. •...
  • Page 8 3. Grab the door by the sides, pull the bottom of the door up and toward you to disengage the hinge supports. Keep pulling the bottom of the door toward you while rotating the top of the door toward the range to com- pletely disengage the hinge levers.

Table of Contents