Elenco Electronics AmeriKit AK-750 Install Manual

AK-750/FUN-755
Cradle Assembly
Use scissors
1/8"
to cut off 1/8".
Lever
Spring
Index Label Shield
NOTE: This
may take a
couple attempts
to attach the two
Index Label
pieces.
NOTE: Be
sure that the
Lever is above the
Hook Switch as
shown.
Lever
Hook Switch
Side View
Hook
Switch
3 x 7mm Screws
Screws Used
(shown actual size)
X4
Lever
Top View 3 x 7mm
2.6 x 14mm Screws
Wiring/Tubing Assembly
Modular Jack
Wiring/Tubing Assembly
1
2
3
NOTE: Follow
Screw Used
these steps for
(shown actual size) wiring the speaker
wires to the PC
board wires.
2.6 x 14mm X2
4
5
Copyright © 2005 Elenco

ASSEMBLY INSTRUCTIONS

Contact Elenco ® Electronics if you have any problems. Actual colors may vary from those shown here.
2.6 x 6mm Screws
Screw Used
(shown actual size)
X2
2.6 x 6mm
Long Part of Spring
Brackets
Short Part of Spring
Handset Assembly
2.6 x 10mm Screws
Decorative Piece
Push Button Panel
Hook Switch
Lever
NOTE: Push Screws Used
the Push Button (shown actual size)
Panel up and
snap it into
position.
2.6 x 10mm
Cut-away View
NOTE:
When
snapping the receiver
cover on, start from the
back.
It may take a couple
attempts to attach
the two pieces.
Cut Tubing
Slide Coiled Cord
Tubing
onto wire.
Twist
wires
together.
Slide
Tubing over
the twisted
wires.
® Electronics, Inc. All Rights Reserved. • 150 Carpenter Ave. • Wheeling, IL 60090 • (800) 533-2441 Fax: (847) 520-0085 • e-mail: elenco@elenco.com • Website: www.elenco.com
2.6 x 6mm Screws
with Washer
Plate
Big Washers
NOTE: Remove any
Keypad Contact
burrs on the buttons
before installing them into
the Push Button Panel.
Remove Burrs
2
Mute Button
Back View
Flash Button
Redial Button
3 2 1
6 5 4
9 8 7
# 0 *
X2
Use this diagram as a
guide when installing
the number buttons.
Final Assembly
Before the Final
Refer to Pages 5 & 6 and perform the
Transmit/Receive & Dial Tests.
Screw Used
(shown actual size)
2.6 x 14mm X2
2.6 x 14mm
Screws
Screw Used
(shown actual size)
X2
2.6 x 6mm with washer
Modular Jack
Speaker Pad
Remove
Backing
Speaker Remove
Number
Button
Speaker Pad
Remove
Backing
NOTE: Make
sure that the angle
on the Flash, Redial,
and Mute buttons are
in the same
direction shown.
Assembly
Phone Number Shield
Phone Number
Label
You have now completed the assembly of the AK-750 Telephone Kit. Refer to
the other side. If the phone does not work, refer to
There are many other
projects or call
AK-750/FUN-755
2.6 x 6mm Screws
Screw Used
(shown actual size)
X3
2.6 x 6mm
PC Board
Input Modular Jack
Buzzer
Buzzer Pad
Remove
Backings
2.6 x 6mm Screws
Screw Used
(shown actual size)
X6
2.6 x 6mm
Bend LED's up
2.6 x 6mm Screws
Keypad PC Board
Microphone
Rubber Microphone Cup
Remove
Backing
FCC Label
Line Cord
Foam Feet
Bottom View
HOW TO USE IT on
TROUBLESHOOTING .
projects: RC Car, Talking Clock, etc. Ask your store about these
at (847) 541-3800.