Acer X1230S series Service Manual

Hide thumbs Also See for X1230S series:

Advertisement

Projector Service Manual
Model:
X1130/X1230/X1230S/X1235/X1230K series
Version: Rev2
First Edition (Dec 2008)
RESTRICTIONS ON USE OF MATERIALS:
1

Advertisement

Table of Contents
loading

Summary of Contents for Acer X1230S series

  • Page 1 Projector Service Manual Model: X1130/X1230/X1230S/X1235/X1230K series Version: Rev2 First Edition (Dec 2008) RESTRICTIONS ON USE OF MATERIALS:...
  • Page 2: Table Of Contents

    REVISION LIST ... 3 CHAPTER 1 SYSTEM SPECIFICATION ... 4 Product Specification ... 4 Electrical Specification...10 Power Supply Specification...14 System Block Diagram ... 15 Product Overview ... 16 CHAPTER 2 SYSTEM UTILITIES... 20 Firmware Upgrade SOP... 20 Method to enter factory menu ... 27 EDID Upgrade SOP ...
  • Page 3: Revision List

    Revision List Version Release Date Rev0 2008.12.23 Rev1 2009.01.07 Rev2 2009.02.23 Revision History First Release (1) Update Ch1- 4.0 Packaging data (2) Add Ch2- Serial Number Upgrade SOP (3) Add Ch5- FRU List Add X1235/X1230K different part : (1) Ch1- SPEC, (2) Ch2- Serial Number Upgrade SOP (3) Ch3- Disassembly process, Module Assembly Key Point...
  • Page 4: Chapter 1 System Specification

    Chapter 1 System Specification Product Specification Optical Performance Image Quality Mechanical Specification Packaging Thermal Specification Environmental Regulatory Reliability Power Requirements Panel Specification Compatibility Image Interface Control Interface User Interface...
  • Page 5 1.6.1 White Tested under 60” (diagonal) image size with Wide projection lens position unless other specified. X1130 : Minimum 1840 Lumens X1230/X1230S : Minimum 1920 Lumens X1235 : Minimum 2080 Lumens X1230K : Minimum 1760 Lumens Minimum 55% Minimum 75% 0.5~2...
  • Page 6 2.8.3 Image Shadow or Blur 0.040 0.040 0.040 typical 55% compare NTSC X1130/X1230 : 53”±5% Diagonal at 2m, Wide X1230S : 54.5”±5% Diagonal at 1m X1235/X1230K : 52.5”±3% Diagonal at 2m, Wide X1130/X1230 : 1.1 X1230S : 1(Fixed) X1235/X1230K : 1.1±2% <1.0% <1.0% Only for X1230S : |A,B| <=3mm, |C|<=2.5 mm with 60”...
  • Page 7 6.0 Environmental 6.1 Temperature 6.2 Humidity 6.3 Audible Noise Level X1230S : 54.5” (Diagonal at 1m) image size. X1235/X1230K : 60” (Diagonal at 2.3m, Wide) image size. 2. Default preset mode “ Dynamic” 3. Full white pattern to check the image.
  • Page 8 1. 12,000 feet @ 25° C (3.5 hours) 2. Altitude Ramp rate: <= 3500 feet per minute (1 hour) Non-operating: 40,000 feet @ -30 ° C (1 hour) X1130/X1230/X1230S : Safety CB, GS, UL, CUL, PSE, CCC X1235/X1230K : CB, GS, UL, CCC...
  • Page 9 Y: Luminance amplitude 1.0 V PbPr/C : Chroma amplitude 0.7 V X1130 : None X1230/X1230S/X1235/X1230K 15 pin D-Sub (Female) x 1 G(Y): Video amplitude 0.7/1.0 Vp-p : Impedance 75Ω RB(CbCr): Video amplitude 0.7 Vp-p : Impedance 75Ω HD/VD/CS: TTL Level IR Receiver x 2 (Front/Top) Angle: ±0°...
  • Page 10: Electrical Specification

    Electrical Specification 1. Timing Table The PC timing is as following: Resolution Mode VGA_60 VGA_72 640 x 480 VGA_75 VGA_85 720x400_70 720 x 400 720x400_85 SVGA_56 SVGA_60 800 x 600 SVGA_72 SVGA_75 SVGA_85 XGA_60 XGA_70 1024 x 768 XGA_75 XGA_85 SXGA_70 1152 x 864 SXGA_75...
  • Page 11 CVBS Amplitude, total (video+ sync) Luminance Amplitude, video Amplitude, sync Impedance CVBS Chroma Amplitude Impedance Audio Impedance (audio in) (Only for Amplitude (audio in) X1230/X1230S Bandwidth S/N Ratio Total Harmonic Distortion fh(kHz) fv(Hz) 15.73 15.63 15.63 15.73 15.63 15.73 15.73 Type -13.2...
  • Page 12 3. Electrical Interface Character Interface Definition 15 pin definition of the mini D-sub male for DDC2B protocol Definition Definition Red video Green Video (Pr) Red Video Return DDCP 5V Horizontal Vertical Sync Sync Video Input 1 1 1 1 C o m p o s i t e i n p u t C o m p o s i t e i n p u t C o m p o s i t e i n p u t C o m p o s i t e i n p u t...
  • Page 13 Input Not Supported Lamp is approaching the end of its useful life in full power operation. Replacement suggested! Video/S-Video YES(NTSC) X1230/X1230S/X1235/X1230K The system does not detect the signal The signal is over the specification Lamp Hour is at 2970 hours YPbPr/YCbCr...
  • Page 14: Power Supply Specification

    The unit shall meet all the operating requirements with the range 90 ~ 264 VAC Frequency Range The unit shall meet all the operating requirements with an input frequency range : X1130/X1230/X1230S/X1235 : 50 Hz ~ 60 Hz X1230K : 47 Hz ~ 63 Hz Power Consumption Normal operation: X1130/X1230/X1230S/X1230K : X1235 : 285W (Max) standby mode: <...
  • Page 15: System Block Diagram

    System Block Diagram Hardware Architecture From AC To Lamp socket Figure 1 Hardware Architecture Main Board Figure 2 Main board & Input board BLOCK DIAGRAM...
  • Page 16: Product Overview

    Product Overview...
  • Page 20: Chapter 2 System Utilities

    Chapter 2 System Utilities Firmware Upgrade SOP DLP Composer LIte Installation Process 1. Double click the Setup file for DLP Composer Lite to start to install program. 2. When the Installation Wizard appears, click “Next”. 3. Select to accept the License Agreement, than click “Next” 4.
  • Page 21 Note: The default installation directory is: C:\Program Files\DLP Composer Lite 7.2 If you want to install to a different directory (perhaps alongside a prior release of DLP Composer™ Lite), click the "Browse" button on the "Select Features" page. 5. When finishing installation, click “Finish”, and then restart your computer to complete the installation process.
  • Page 22 (1) Select Library 1. When start to use this program to download at first time, you need to check if the library folder is existed under the path of Library. Click “Browse” to select path for library files 2. Check if there are library files in the assigned path. If not, unzip the file “library_20090214.zip”...
  • Page 23 Hardware required 1. Standard RS232 Download cable 2. Personal computer or laptop computer Software required 1. DLP Composer Lite program 2. New version FW Download procedure 1. Prepare the download equipment: RS232 cable connect to PC and projector 2. Plug power cord into projector , and the projector will be in stand by mode 3.
  • Page 24 Caution: do not interrupt download like unplug power cable. If you skip boot loader Area and interrupt download, Projector would not turn on anymore. 6. Click on “Flash Loader” and “Browse”->select file->”Open” to select the path of the image file(new version firmware)
  • Page 25 7. Click “Reset Bus” and then check the status that shows “Bus Reset”. 8. Select “Start download” and three LED light orange color...
  • Page 26 9. After download complete, program will show “Download complete” message, and projector will reset to stand by mode. 10. If program pops out another error message after “Download complete” message appearing, it’s ok to skip the error message. 11. After download completing, it’s necessary to unplug power cord, then re-plug power cord and restart projector.
  • Page 27: Method To Enter Factory Menu

    Method to enter factory menu Press keypad Power and image will show Power Down OSD function Press keypad Left twice then press Menu, then enter the Factory mode. Step 1 Step 2...
  • Page 28: Edid Upgrade Sop

    J8 : 1,2 short J10 : short 3. How to use Download Tool : Link to Projector : For DVI-D DDC download (no need in X1130/ X1230/ X1230S/ X1235/ X1230K series) Link to Projector : For HDMI DDC download X1130/ X1230/ X1230S/...
  • Page 29 Software Installation, Un-installation : Unzip the “Q-EDID” program files in the same directory. Install Q-EDID tool : Execute “Install Q-EDID.BAT” to install & register EDID Board into the computer. Un-install Q-EDID tool : If you want to uninstall this tool, execute “Uninstall Q-EDID.BAT”, then it will remove EDID Board from the computer.
  • Page 30 Step2 Step4 (3) Read EDID: • Read D-SUB/DVI EDID: 1. EDID Type Selection : Choose ‘‘EDID 128 Bytes’’ 2. Read EDID : Click “Read EDID”. 3. While complete, it will show message’’ Read EDID OK… ‘’, and the read-out DDC will show in the table in program.
  • Page 31: Serial Number Upgrade Sop

    Serial Number Upgrade SOP Hardware required Standard RS232 Download cable Personal computer or laptop computer Software required 1. Acer_Service_Tool(Data)_3.1.exe When need to use this Serial Number Upgrade program: When it’s time to replace Main board for repair, it’s necessary to rewrite original S/N and some adjustment values into new Main board by the following process.
  • Page 32 6. Click “Save” to save data into the assigned file name. 7. Change new Main board: (1) Unplug power cable and RS232 cable from projector, and change new Main board into Projector. (2) After changing Main board, reconnect power cable and RS232 cable into Projector. 8.
  • Page 33: Chapter 3 System Disassembling And Replacement

    (1) Take off the case outlet case module FRONT (2) Take off the front IR BD case module (3) (For X1230/X1230S/X1230S/ X1230K): Take off the screw*4 (M3*7L) and speaker from the outlet case module Three long sponge <For X1130> :...
  • Page 34 Ballast 5-Pin wire, speaker wire (For X1230/X1230S/ X1235/X1230K) from M/B. (2) Take off inlet case module. Ballast 5Pin wire 8 Take off the M/B screw*5 C/W FPC wire blower fan wire speaker wire (For X1230/X1230S) Main BD screw driver twin screw driver...
  • Page 35 <For X1130/X1230/X1235/X1230K> Disassemble the screw*3(M3*7L), and take off the OPT eng . screw*1 blower fan's thermal wire screw*1 screw*1 screw*1 <For X1230S> anchor 定 位 point 点 screw driver screw driver grounding screw *1 Ballast Mylar...
  • Page 36 Focus Ring. <For X1130/X1230/X1235/X1230K> <For X1130/X1230/ X1235/X1230K>: (1)Take off Zoom Ring and Ring screw*2(M2*3L). (2)Take off the LENS <For X1230S> screw*3(M3*4L) and the Projection Lens. <For X1230S>: (1)Take off Focus Ring. (2)Take off the LENS screw*4(M3*6L) and Mylar <For X1230S>:...
  • Page 37 Disassemble the screw*4(M3*15.15L), and take off the HSINK and DMD chip BD with DMD Chip. (1)Disassemble the baffle DMD. (2)Disassemble the screw*3(M3*4L) and take off the CW module. baffle DMD Rotate to open the switch on socket, and take off the DMD chip. (1)Disassemble ILL module screw*2(M2.5*5L).
  • Page 38: Module Assembly Key Point - Optical Engine

    Module Assembly Key Point - Optical Engine 1. Light Pipe Module assembly and overfill alignment 1.1 Assembly LP Module to HSG DMD (3) Assembly two Overfill adjustment screws to HSG DMD (Fig. 1-1). ** Adjustment criteria refer to below item (4) Assembly “Clip LP”...
  • Page 39 1. Press down the Clip 2. Insert the LP Module LP Datum of DMD HSG Fig. 1-3 Fig. 1-4 Overfill adjustment screws...
  • Page 40 1. Place Clips on BKT surface Pre assemble this screw not over the bottom surface. 3. Lock screw 2. Push Baffle LP to hook DMD HSG Fig. 1-5-1 Fig. 1-6 Fig. 1-5-2 Pre assemble this screw not over the side surface.
  • Page 41 2. Assembly FM Module: Place FM on “HLD FM” surface(Fig. 2-1) and use “Clip FM” to fix FM(Fig. 2-2). Touch the side surface Fig. 2-2 3. Assembly HSG ILL Module: 3.1 CM Assembly Insert “Clip CM Side” first, and then place “Clip Front CM” to fixed-shaft of ILL SUB before locking screw (Fig.
  • Page 42 Datum3 Datum1 Datum2 Fig. 3-3 Clip UP CM Fig. 3-4 Fig. 3-5 Sponge Fig. 3-6...
  • Page 43 4. AL, HSG ILL and HSG DMD Assembly: 4.1 Placed “AL” on the “HSG DMD”. The “raised surface” of “AL” shall toward “DMD direction” (Fig. 4-1). 4.2 To assemble ”HSG ILL SUB Module” with “HSG DMD” and cover over on “AL” and the then lock with screws (Fig.
  • Page 44 5. DMD and Chip B/D Module: 5.1. Judge Chip B/D and DMD alignment keying first (Fig. 5-1, 5-2). 5.2. Alight keying and Assemble DMD to Chip B/D (Fig. 5-3). 5.3. Push DMD slightly and use screwdriver rotate clockwise button to lock (close notation) DMD on Chip B/D (Fig.
  • Page 45 (Fig. 6-1). 7. Assembly OP ENG 7.1 Assemble “Baffle DMD” to “HSG DMD” (Fig.7-1). 7.2 Assemble Chip B/D Module to “HSG DMD” (Fig. 7-2). Fixed shafts of DMD HSG Fixed shafts of DMD HSG 7.3 Assemble Thermal Pad & Gasket Hest-sink then place contact DMD (Fig. 7-3). (1) Pre-fastening Sequence: [ 1 ] - [ 2 ] - [ 3 ] - [ 4 ].
  • Page 46 ○ ○ 7.4 Assemble “CW Module” to “DMD HSG” and lock with screws well (Fig.7-4). Fixed shafts of DMD HSG For X1130/X1230/X1235/X1230K : Assemble “PL Lens” and lock with screws well (Fig. 7-5). Screw Fig. 7-3 Screw Fig.7-4 Fig. 7-5 Screw Gasket...
  • Page 47 Ring Zoom Ring Focus For X1130/X1230/X1235/X1230K : Assemble Lamp Module to “BKT Link Lamp” and then lock with screw well (Fig. 7-8, Fig. 7-9). Screw Fig. 7-6 Fig. 7-7 Fig. 7-8 Screw Fixed shafts...
  • Page 48 Fig. 7-9 7.7 For X1230S : Assemble “Frame Lens Wide” and lock with screws well (Fig. 7-10). Fig. 7-10 A Gap for LP Adjustment Screws...
  • Page 49 7.8 For X1230S : Assemble “PL Lens” and lock with screws well (Fig. 7-11). Screws 7.9 For X1230S : Assemble “Ring Focus” (Fig.7-12). Ring Focus Fig. 7-11 Fig. 7-12...
  • Page 50 7.10 For X1230S : Assemble Lamp Module to “BKT Link Lamp” and then lock with screw well (Fig.7-13, Fig. 7-14). Screw Fixed shafts Fig. 7-13 Fig. 7-14...
  • Page 51: Module Assembly Key Point - Mechanical

    Module Assembly Key Point – Mechanical 1. lower case and Adjust foot 2. Ballast wire Alignment dressed Ballast to PWR wire must go outside this rib Spring should be no bend Two screws...
  • Page 52 Ballast to Lamp wire should align in to this groove Ballast to Lamp wire also should align under Mylar groove...
  • Page 53 First: assy Blower module Second: assy Mylar Ballast This cord location is here...
  • Page 54 3. Blower wire alignment This clip must be screwed by this direction...
  • Page 55 Lamp box must be assembled into lower case Rib 5. CW sensor board wire and CW FPC cable alignment 6. Grounding wire alignment...
  • Page 56 7. Twin Fan and Speaker wire alignment 8. Front IR wire to MB alignment Front IR wire should align in to these grooves...
  • Page 57 9. Ballast to lamp wire alignment Lamp box should align with the lower case Lamp connector assemble with rib 10. Eng screw assemble sequence...
  • Page 58 Second First Third 11. Lamp Door screw assemble sequence...
  • Page 59: Chapter 4 Troubleshooting

    Chapter 4 Troubleshooting System Analysis Keypad LED OK If Power On, Lamp On? No Signal? Power Auto Turn Off IR Remote Control NG? Pixel Fail? Step: Check Lamp Door Check Power Board and Interlock Check Connection between PWR BD and Main BD Check Main Board Check Lampen wire , Lamp wire and Ballast wire...
  • Page 60: Optical Problems Checking Items

    Optical Problems Checking Items Item Brightness Uniformity FOFO Contrast ANSI Contrast Color Color Uniformity Blue Edge Blue/Purple Border Focus Dust Horizontal/Vertical Strips Pixel Fail Trouble Shooting Guide 1. Change lamp 1. Change lamp 1. Check ADC calibration 2. Check user’s menu brightness & contrast are default 3.
  • Page 61 “Blue Edge” Trouble Shooting: I. Re-adjust “Overfill” first. For Overfill Re-adjustment: i. Those 2 Adjustment Screws must be released for around 2 mm first. ii. Alignment Sequence: To adjust “Horizontal Adjustment Screw” firstly, then “Vertical Adjustment Screw”. Refer to below Figure. (2) Overfill Vertical Adjustment Screw II.
  • Page 62: Power Supply Problems Checking Flow

    Power Supply Problems Checking Flow...
  • Page 64: Led Messages Definition

    LED Messages Definition External Status indicator LED Name Power LED Lamp Status LED Temperature Status LED Lamp_LED Power Plug Flash ON to OFF Standby Power button ON Lamp retry Cooling state Power button OFF: Cooling completed; Standby Mode Firmware Download Thermal sensor error (T2 ≧...
  • Page 65 Thermal sensor 1 Fan 3 : Fan 1 : Blower Fan Lamp Fan Thermal sensor 2 Fan 2 : Power Fan message...
  • Page 66: Error Count Messages Definition

    Error Count Messages Definition Error Count LAMP OFF LAMP Fail error LAMP FAN SPEED ERROR FAN 1 Speed Error BALLAST FAN SPEED FAN 2 Speed Error ERROR BLOWER FAN SPEED FAN 3 Speed Error ERROR Main Board SENSOR ERROR DETECT Sensor 1 Sensor 1 Open Error Power board SENSOR Sensor 2 Open Error...
  • Page 67: Rs232 Connection

    RS232 Connection 1. Connection: Below shows the illustration of connection between PC and Projector. <CAUTION> Make sure that your computer and projector are turned off before connection. Power on the computer first, and then plug the power cord of the projector. (It may cause Com port incorrect function, if you do not follow this instruction) Adapters may be necessary depending on the PC connected to this projector.
  • Page 68 Interface Settings RS-232 protocol Baud Rate Data Length Parity Check Stop Bit Flow Control Command Category Refer to Appendix A 115200 bps 8 bit None 1 bit None...
  • Page 69: Adjustment / Alignment Procedure

    Adjustment / Alignment Procedure Content : 1. Color Wheel Delay Alignment 2. Overfill adjustment 3. PC Alignment Procedure 4. YUV Alignment Procedure 5. Keystone Calibration...
  • Page 70 1. Color Wheel Delay Alignment Procedure: Enter Factory Mode Enter Block 1 Change CW Delay by adjusting the following gray pattern to smooth 32 Gray pattern...
  • Page 71 2. Overfill adjustment (Blue Edge adjustment) 1. “Full White Pattern” is suggested for this alignment. 2. Adjust 2 LP-alignment Screws (upper side / lower front side of Optical Engine) behind Color Wheel. 3. Alignment Criteria is to adjust these 2 screws until “No Dark Edges” and “ No Shadows”...
  • Page 72 PC Alignment Procedure OSD Default value: Item Cal R Offset Cal G Offset Cal B Offset Cal R Gain Cal G Gain Cal B Gain YPbPr R Offset YPbPr B Offset Procedure: Gray Level: Connect power, D-sub, into projector. Change Timing and pattern of pattern generator: Timing: 1024*768 @60Hz (XGA) Pattern: As White-black pattern {A near white color (240,240,240) and a near black color(16,16,16)}...
  • Page 73 4. YUV Alignment Procedure OSD Default value: Item Cal R Offset Cal G Offset Cal B Offset Cal R Gain Cal G Gain Cal B Gain YPbPr R Offset YPbPr B Offset Procedure: 1. Connect power, YpbPr cable (only G cable from DVD player) into projector. 2.
  • Page 74 5. Keystone Calibration Condition:Horizontal plane(0∘) 1. Make projector be horizontal 2. Enter factory menu 3. Enter into Block in factory menu 4. Select item “AutoKeystoneCal” 5. Press key Left or Right to do auto calibration ∘ 6. Finish 0 calibration and bellow items will show data AutoKeystoneXCal: ≦...
  • Page 75: Chapter 5 Fru List

    Chapter 5 FRU List Exploded Diagram Module 1 – Total Exploded View Note : (item 9 ) There’s no Speaker in X1130. (item 23 ) There’s no Zoom Ring in X1230S...
  • Page 77: Module 2 - Assy Upper Case

    Module 2 – ASSY UPPER CASE...
  • Page 78: Module 3 - Assy Lower Case

    Module 3 – ASSY LOWER CASE...
  • Page 79: Module 4 - Assy Front Case

    Module 4 – ASSY FRONT CASE...
  • Page 80: Fru List

    FRU List Use in Model CATEGORY X1130/ X1230/ ACCESSORY X1230S X1130 BOARD X1230/X1230 BOARD X1130/ X1230/ BOARD X1230S X1130/ X1230/ BOARD X1230S X1130/ X1230/ BOARD X1230S X1130/ X1230/ BOARD X1230S X1130/ X1230/ CABLE X1230S X1130/ X1230/ CABLE X1230S X1130/ X1230/...
  • Page 81 X1130/ X1230/ CABLE X1230S X1130/ X1230/ CABLE X1230S X1130/ X1230/ CABLE X1230S X1130/ X1230/ CABLE X1230S X1130/ X1230/ CABLE X1230S X1130/ X1230/ CABLE X1230S X1130/ X1230/ CABLE X1230S X1130/ X1230/ CABLE X1230S X1130/ X1230/ CABLE X1230S CASE/COVE X1130 R/BRACKET ASSEMBLY...
  • Page 82 CASE/COVE X1130/ X1230 R/BRACKET ASSEMBLY CASE/COVE X1230S R/BRACKET ASSEMBLY X1130/ CASE/COVE X1230/ R/BRACKET X1230S ASSEMBLY CASE/COVE X1130/ X1230 R/BRACKET ASSEMBLY CASE/COVE X1230S R/BRACKET ASSEMBLY X1130/ CASE/COVE X1230/ R/BRACKET X1230S ASSEMBLY CASE/COVE X1130/ X1230 R/BRACKET ASSEMBLY CASE/COVE X1130/ X1230 R/BRACKET ASSEMBLY...
  • Page 83 X1130/ DIGITAL X1230/ LIGHT X1230S DEVICE DIGITAL X1130/ X1230 LIGHT DEVICE DIGITAL X1230S LIGHT DEVICE DIGITAL X1130 LIGHT DEVICE DIGITAL X1230/ LIGHT X1230S DEVICE DIGITAL X1130 LIGHT DEVICE DIGITAL X1230/ LIGHT X1230S DEVICE X1130/ X1230/ X1230S X1130/ X1230/ X1230S X1230/...
  • Page 84: Appendix A - Code List: Ir / Rs232 / Ddc Data

    Appendix A - Code List: IR / RS232 / DDC Data 1. Remote Control Code: IR setting value Frequency: 38kHz Protocal: NEC format b. IR command code Customer code: : : : 0813...
  • Page 85: Rs-232 Command Code

    2. RS-232 Command Code General command type (Projector ‘receives’ commands) Function feature Code (character) OKOKOKOKOK Power On * 0 IR 001 Power On * 0 IR 002 Power Off * 0 IR 004 Keystone * 0 IR 006 Mute * 0 IR 007 Freeze * 0 IR 008 Menu...
  • Page 86 * 0 IR 044 Keystone Left * 0 IR 045 Keystone Right * 0 IR 046 Zoom * 0 IR 047 e-Key * 0 IR 048 Color RGB * 0 IR 049 Language * 0 IR 050 Source HDMI General command type (Projector ‘transmits’ commands) Function feature Code (character) Model XXXXXXXX Return the Model name...
  • Page 87: Ddc Data

    3. DDC Data: X1130 EDID : : : : EDID Block 0, Bytes 0-127 [00H-7FH] Block Type: EDID 1.3 ________________________________________________________________ 0 | 00 FF FF FF FF FF FF 00 04 72 05 90 01 00 00 00 10 | 01 12 01 03 0E 00 00 78 0A F4 46 A4 58 58 89 25 20 | 13 4F 5B BF EF 80 71 4A 81 80 81 40 90 40 A9 40 30 | 81 00 95 00 B3 00 A0 0F 20 00 31 58 1C 20 28 80 40 | 14 00 00 00 00 00 00 18 00 00 00 FD 00 30 56 1F...
  • Page 88 Standard Timing ID 1: 1152 x 864 @70Hz Standard Timing ID 2: 1280 x 1024 @60Hz Standard Timing ID 3: 1280 x 960 @60Hz Standard Timing ID 4: 1400 x 1050 @60Hz Standard Timing ID 5: 1600 x 1200 @60Hz Standard Timing ID 6: 1280 x 800 @60Hz Standard Timing ID 7: 1440 x 900 @60Hz Standard Timing ID 8: 1680 x 1050 @60Hz...
  • Page 89 X1230 EDID : : : : EDID Block 0, Bytes 0-127 [00H-7FH] Block Type: EDID 1.3 ________________________________________________________________ 0 | 00 FF FF FF FF FF FF 00 04 72 05 91 01 00 00 00 10 | 01 12 01 03 0E 00 00 78 0A F4 46 A4 58 58 89 25 20 | 13 4F 5B BF EE 80 71 4A 81 80 81 40 81 00 95 00 30 | 61 59 01 01 01 01 64 19 00 40 41 00 26 30 18 88 40 | 36 00 00 00 00 00 00 18 00 00 00 FD 00 30 56 1F...
  • Page 90 Standard Timing ID 3: 1280 x 960 @60Hz Standard Timing ID 4: 1280 x 800 @60Hz Standard Timing ID 5: 1440 x 900 @60Hz Standard Timing ID 6: 1024 x 768 @85Hz Standard Timing ID 7 - Not Used Standard Timing ID 8 - Not Used ______________________________________________________________________ (36H-47H) Detailed Timing / Descriptor Block 1: 1024x768 Pixel Clock: 65.00 MHz...
  • Page 91 X1230S EDID : : : : EDID Block 0, Bytes 0-127 [00H-7FH] Block Type: EDID 1.3 ________________________________________________________________ 0 | 00 FF FF FF FF FF FF 00 04 72 05 92 01 00 00 00 10 | 01 12 01 03 0E 00 00 78 0A F4 46 A3 58 58 88 24...
  • Page 92 Max Horiz. Freq - 93 kHz Pixel Clock - 110 MHz GTF - Not Used ______________________________________________________________________ (5AH-6BH) Detailed Timing / Descriptor Block 3: Monitor Name: X1230S ______________________________________________________________________ (6CH-7DH) Detailed Timing / Descriptor Block 4: Monitor Serial Number: J92050018401 (7EH) Block No: No Extension EDID Block(s)
  • Page 93 X1235 EDID : : : : EDID Block 0, Bytes 0-127 [00H-7FH] Block Type: EDID 1.3 ________________________________________________________________ 0 | 00 FF FF FF FF FF FF 00 04 72 05 97 01 00 00 00 10 | 01 12 01 03 0E 00 00 78 0A F4 46 A4 58 58 89 25 20 | 13 4F 5B BF EE 80 71 4A 81 80 81 40 81 00 95 00 30 | 61 59 01 01 01 01 64 19 00 40 41 00 26 30 18 88 40 | 36 00 00 00 00 00 00 18 00 00 00 FD 00 30 56 1F...
  • Page 94 Standard Timing ID 3: 1280 x 960 @60Hz Standard Timing ID 4: 1280 x 800 @60Hz Standard Timing ID 5: 1440 x 900 @60Hz Standard Timing ID 6: 1024 x 768 @85Hz Standard Timing ID 7 - Not Used Standard Timing ID 8 - Not Used ______________________________________________________________________ (36H-47H) Detailed Timing / Descriptor Block 1: 1024x768 Pixel Clock: 65.00 MHz...
  • Page 95 X1230K EDID : : : : EDID Block 0, Bytes 0-127 [00H-7FH] Block Type: EDID 1.3 ________________________________________________________________ 0 | 00 FF FF FF FF FF FF 00 04 72 05 98 01 00 00 00 10 | 01 12 01 03 0E 00 00 78 0A F4 46 A4 58 58 89 25 20 | 13 4F 5B BF EE 80 71 4A 81 80 81 40 81 00 95 00 30 | 61 59 01 01 01 01 64 19 00 40 41 00 26 30 18 88 40 | 36 00 00 00 00 00 00 18 00 00 00 FD 00 30 56 1F...
  • Page 96 Standard Timing ID 3: 1280 x 960 @60Hz Standard Timing ID 4: 1280 x 800 @60Hz Standard Timing ID 5: 1440 x 900 @60Hz Standard Timing ID 6: 1024 x 768 @85Hz Standard Timing ID 7 - Not Used Standard Timing ID 8 - Not Used ______________________________________________________________________ (36H-47H) Detailed Timing / Descriptor Block 1: 1024x768 Pixel Clock: 65.00 MHz...

This manual is also suitable for:

X1130 seriesX1230 seriesX1235 seriesX1230k series

Table of Contents