Page 2: Table Of Contents
Table of contents Seat, seatbelt and SRS airbags Keys and doors Instruments and controls Climate control Audio Interior equipment Starting and operating Driving tips In case of emergency Appearance care Maintenance and service Specifications Consumer information and Reporting safety defects Index –...
Page 3 Foreword Congratulations on choosing a SUBARU vehicle. This Owner’s Manual has all the information necessary to keep your SUBARU in excellent condition and to properly maintain the emission control system for minimizing emission pollutants. We urge you to read this manual carefully so that you may understand your vehicle and its operation.
Page 4 This manual describes the following types of the Legacy series. HBF016AB HBF017AB HBF018AB HBF019AB...
Page 5 Warranties B Warranties for U.S.A. All SUBARU vehicles distributed by Subaru of America, Inc. and sold at retail by an authorized SUBARU dealer in the United States come with the following warranties: D SUBARU Limited Warranty D Emission Control Systems Warranty...
Page 6: Seat, Seatbelt And Srs Airbags
This chapter informs you how to start and operate your SUBARU. Chapter 8: Driving tips This chapter informs you how to drive your SUBARU in various condi- tions and explains some safety tips on driving. Chapter 9: In case of emergency This chapter informs you what to do if you have a problem while driving, such as a flat tire or engine overheating.
Page 7: Safety Warnings
Chapter 11: Maintenance and service This chapter informs you when you need to take your SUBARU to the dealer for scheduled maintenance and informs you how to keep your SUBARU running properly. Chapter 12: Specifications This chapter informs you about dimension and capacities of your SUBARU.
Page 8 J Safety symbol You will find a circle with a slash through it in this manual. This symbol means “Do not”, “Do not do this”, or “Do not let this happen”, depending upon the context. Safety precautions when driving SEATBELT AND SRS AIRBAG WARNING D All persons in the vehicle should fasten their seatbelts BE- FORE the vehicle starts to move.
Page 9 deploys could suffer very serious injuries. Because the SRS air- bag needs enough space for deployment, the driver should al- ways sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full vehicle control and the front passenger should move the seat as far back as possible and sit upright and well back in the seat.
Page 10 CLOSE TO THE SRS AIRBAG. D Always use the child safety locks whenever a child rides in the rear seat. Serious injury could result if a child accidentally opened the door and fell out. Refer to the “Door locks” section in chapter 2.
Page 11 D Never run the engine in a closed space, such as a garage, ex- cept for the brief time needed to drive the vehicle in or out of it. D Avoid remaining in a parked vehicle for a lengthy time while the engine is running.
Page 12 DRUGS AND DRIVING WARNING There are some drugs (over the counter and prescription) that can delay your reaction time and impair your perception, judg- ment and attentiveness. If you drive after taking them, it may in- crease your, your passengers’ and other persons’ risk of being involved in a serious or fatal accident.
Page 13 CAR PHONES AND DRIVING CAUTION A driver’s use of a car phone can be distracting and if special care is not taken, can lead to an accident. If you use a car phone while driving, make an extra effort to pay attention to the road and to traffic at all times.
Page 14 TIRE PRESSURES WARNING Driving at high speeds with excessively low tire pressures can cause the tires to deform severely and to rapidly become hot. A sharp increase in temperature could cause tread separation, and destruction of the tires. The resulting loss of vehicle control could lead to an accident.
Page 15 Illustrated index J Exterior Hood lock release (page 11-5) Headlight switch (page 3-19) Bulb replacement (page 11-57) Wiper switch (page 3-26) Moonroof (page 2-30) Roof rail (page 8-20) Door locks (page 2-3) Tire pressure (page 11-39) Flat tires (page 9-4) Tire chains (page 8-16) Fog light switch (page 3-24) Tie-down hooks (page 9-15)
Page 16 Rear wiper switch (page 3-28) Rear window defogger switch (page 3-29) Fuel filler lid (page 7-4) Child safety locks (page 2-20) Towing hook (page 9-15) HBF013BB Trunk/Rear gate (page 2-24/2-29) Tie-down hooks (page 9-15) Bulb replacement (page 11-61) – CONTINUED – HBB027CB xiii...
Page 17 J Interior B Passenger compartment area Lower anchorage for child restraint system (page 2-20) Seatbelt (page 1-16) Parking brake lever (page 7-32) Front seat (page 1-2) Rear seat (page 1-10) HBF038BB...
Page 18 Moonroof (page 2-30) Interior lights (page 6-2) Rear center passenger’s seat seatbelt (page 1-16) Sun visors (page 6-4) Spot light (page 6-3) Inside mirror (page 3-31) – CONTINUED – HBF026BB...
Page 19 Cup holder (page 6-8) Center console (page 6-6) Glove compartment (page 6-6) Cigarette lighter (page 6-9) Ashtray (page 6-12) HBF036BB...
Page 20 B Trunk/cargo area Shopping bag hook (page 6-14) Accessory socket (page 6-13) Cargo anchorage eyelets (page 6-18) HBF015BB HB7008DB HB7019BB Luggage cover (page 6-16) Storage tray (page 6-18) Jack (page 9-27) Jack handle (page 9-27) Spare tire (page 9-27) HB7015CB HB8004CB –...
Page 21: Instrument Panel
J Instrument panel Door locks (page 2-3) Outside mirror (page 3-34) Light control lever (page 3-19) Combination meter (page 3-7) Wiper control lever (page 3-24) Hazard warning flasher switch (page 3-7) Climate control (page 4-1) Gear shift lever (MT) (page 7-11)/Selector lever (AT) (page 7-14) xviii Audio (page 5-1)
Page 22 J Light control and wiper control levers/switches Parking light switch (page 3-23) Windshield wiper (page 3-24) Mist (page 3-26) Windshield washer (page 3-26) Rear window wiper and washer switch (page 3-28) Wiper control lever (page 3-26) Illumination brightness control (page 3-22) Light control lever (page 3-19) Headlight ON/OFF...
Page 23: Combination Meter
J Combination meter B Overview SRS airbag system warning light (page 3-11) VDC warning light (page 3-15) VDC operation indicator light (page 3-17) VDC OFF indicator light (page 3-18) Brake system warning light (page 3-16) Seatbelt warning light (page 3-11) Turn signal indicator light (page 3-18) Door open warning light...
Page 24 B Warning and indicator light Mark Seatbelt warning light SRS airbag system warning light AIRBAG CHECK ENGINE warning light/ Malfunction indicator lamp Charge warning light Oil pressure warning light AT OIL temperature warning light (if equipped) ABS warning light VDC warning light (if equipped) Brake system warning light Door open warning light Low fuel warning light...
Page 25 Seat, seatbelt and SRS airbags Front seats ..............Seat heater (if equipped) Rear seats .
Page 26: Front Seats
Front seats WARNING D Never adjust the seat while driving to avoid the possibility of loss of vehicle control and of personal injury. D Never drive the vehicle with the head restraints removed be- cause they are designed to reduce the risk of serious neck injury in the event that the vehicle is struck from the rear.
Page 27 adults, their risk of being injured from deployment is greater. For that reason, we strongly recommend that ALL children (including those in child seats and those that have outgrown child restraint devices) sit in the REAR seat properly restrained at all times in a child restraint device or in a seatbelt, whichever is appropriate for the child’s age, height and weight.
Page 28: Fore And Aft Adjustment
Put children in the rearseat properly restrained at all times. B Fore and aft adjustment n Manual type Pull the lever upward and slide the seat to the desired position. Then release the lever and move the seatback and forth to make sure that it is securely locked into place.
Page 29 Seat, seatbelt and SRS airbags n Power seat (if equipped) HB1060BA To adjust the seat forward or backward, move the control switch for- ward or backward. B Seat cushion angle and height adjustment (Power seat only) HB1078BA HB1062BA To adjust the angle and height of the seat cushion, move the control switch in the corresponding direction.
Page 30 B Reclining the seatback n Manual type Pull the reclining lever up and adjust the seatback to the desired posi- tion. Then release the lever and make sure the seat is securely locked into place. The seatback placed in a reclined position can spring back upward with force when released.
Page 31 NOTE While adjusting the seatback, you can not at the same time adjust the seat position or the seat cushion angle and height. B Head restraint adjustment To raise the head restraint, pull it up. To lower it, push the head restraint down while pressing the release button on the top of the seatback.
Page 32 HBS011AA 1. Slide the front seat forward as far as possible. 2. Pull off the head restraint while pressing the release button. 3. Recline the seatback rearward up to the lowest position. Remem- ber to reinstall the head restraint whenever the seatback is raised back.
Page 33: Seat Heater (If Equipped)
Seat heater (if equipped) CAUTION D Use of the seat heater for a long period of time while the engine is not running can cause battery discharge. D Do not put anything on the seat which insulates against heat, such as a blanket, cushion, or similar items. This may cause the seat heater to overheat.
Page 34: Rear Seats
Rear seats WARNING D Seatbelts provide maximum restraint when the occupant sits well back and upright in the seat. Do not put cushions or any other materials between occupants and seatbacks or seat cushions. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will increase, and both can result in serious internal injury or death.
Page 35 Seat, seatbelt and SRS airbags HB1068BB HB1100BB To lower the armrest, pull on the top edge of the armrest. B Loading long objects (Sedan) WARNING D Secure long objects properly to prevent them from shooting forward and causing serious injury during a sudden stop or sharp cornering.
Page 36: Rear Center Seating Position On Station Wagon
Folding down the armrest and opening the seatback panel affords a loading space for long objects. To open the seatback panel, pull the panel down while pressing the release tab down. J Headrest adjustment — Rear center seating position on Station wagon To raise the headrest, pull it up.
Page 37 Seat, seatbelt and SRS airbags B Folding down the seatback HB1094BA HB1095BA 1. Lower the headrests. 2. Unlock the seatback by pulling the release knob and then fold the seatback down. B Folding down the seat cushion and seatback 1. Move the front seat forward. 2.
Page 38 4. Store the seatbelts in the seatbelt pockets to prevent them from fal- ling below the cushion. HB1074BB 5. Raise the seat cushion by pulling up the tab. Make certain that the rear passenger’s cup holder is fully retracted before raising the seat cushion. HB1097BA 6.
Page 39 7. Install the headrests (if so equipped) onto the backside of the seat- back (window-side positions only). To return the rear seat to its original position, raise the seatback and seat cushion until they lock into place and make sure that they are securely locked.
Page 40: Seatbelts
Seatbelts J Seatbelt safety tips WARNING D All persons in the vehicle should fasten their seatbelts BE- FORE the vehicle starts to move. Otherwise, the possibility of se- rious injury becomes greater in the event of a sudden stop or ac- cident.
Page 41: Emergency Locking Retractor (Elr)
According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. For instructions and precautions concerning the child restraint system, see the “Child restraint systems” section in this chapter. B Infants or small children Use a child restraint system that is suitable for your vehicle.
Page 42: Automatic/Emergency Locking Retractor (A/Elr)
J Automatic/Emergency Locking Retractor (A/ELR) Each passenger’s seatbelt has an Automatic/Emergency Locking Re- tractor (A/ELR). The Automatic/Emergency Locking Retractor normally functions as an Emergency Locking Retractor (ELR). The A/ELR has an additional locking mode “Automatic Locking Retractor (ALR) mode” in- tended to secure a child restraint system.
Page 43 If an accident occurs, this can increase the risk or severity of injury. D Keep the lap belt as low as possible on your hips. In a colli- sion, this spreads the force of the lap belt over stronger hip bones instead of across the weaker abdomen.
Page 44 B Front seatbelts 1. Adjust the seat position: Driver’s seat: Adjust the seatback to the upright position. Move the seatback as far from the steering wheel as practical while still main- taining full vehicle control. Front passenger’s seat: Adjust the seatback to the upright position. Move the seat as far back as possible.
Page 45 Seat, seatbelt and SRS airbags HB1029BB The shoulder belt anchor height should be adjusted to the position best suited for you. To lower the anchor height, push the release but- ton and slide the anchor down. To raise the anchor height, slide the anchor up.
Page 46 B Rear seatbelts (except rear center seatbelt on wagon) OM-H0043 OM-H0044 1. Sit well back in the seat. 2. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly.
Page 47 erly to avoid catching the belt webbing in the door. B Rear center seatbelt on wagon model WARNING D Fastening the seatbelt with the webbing twisted can increase the risk or severity of injury in an accident. When fastening the belt after it is pulled out from the retractor, especially when inserting the connector’s tongue plate into the mating buckle (on right-hand side), always check that the webbing is not twisted.
Page 48 1. Pull out the seatbelt slowly from the overhead retractor. 2. After confirming that the webbing is not twisted, insert the connec- 1-24 1. Center seatbelt tongue plate 2. Connector (tongue) 3. Connector (buckle) 4. Center seatbelt buckle HS1017BB HB1032BA HB1033BA...
Page 49 tor (tongue) attached at the webbing end into the buckle on the right- hand side until a click is heard. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly. If the belt still cannot be unlocked, let the belt retract slightly after giving it a strong pull, then pull it out slowly again.
Page 50 n Unfastening the seatbelt Push Push the release button of the center seatbelt buckle (on the left-hand side) to unfasten the seatbelt. NOTE When the seatback is folded down for greater luggage space, it is necessary to disconnect the connector. CAUTION D Do not allow the retractor to roll up the seatbelt too quickly.
Page 51 Seat, seatbelt and SRS airbags HB1036BA HB1037BA 1. Insert a key or other hard pointed object into the slot in the con- nector (buckle) on the right-hand side and push it in, and the connec- tor (tongue) plate will disconnect from the buckle. HB1038CA HB1048BA 2.
Page 52: Seatbelt Maintenance
J Seatbelt maintenance CAUTION D Keep the belts free of polishes, oils, chemicals and particularly battery acid. D Never attempt to make modifications or changes that will pre- vent the seatbelt from operating properly. To clean the seatbelts, use a mild soap and lukewarm water. Never bleach or dye the belts because this could seriously affect their strength.
Page 53: Front Seatbelt Pretensioners
For required servicing of front seatbelt retractors equipped with seatbelt pretensioners, see your nearest SUBARU dealer. D When discarding front seatbelt retractor assemblies or scrap- ping the entire car due to collision damage or for other reasons, consult your SUBARU dealer.
Page 54 SUBARU dealer as soon as possible. D If the front seatbelt retractor assembly or surrounding area has been damaged, contact your SUBARU dealer as soon as pos- sible. D When you sell your vehicle, we urge you to explain to the buy- er that it has seatbelt pretensioners by alerting him to the con- tents of this section.
Page 55 D All related wiring In the event of a malfunction indicated by any of following, the vehicle should be taken promptly to your nearest SUBARU dealer to have the system checked. Unless checked and repaired, the seatbelt preten- sioners and airbags will not function reliably: D Flashing or flickering of the indicator light.
Page 56 WARNING D When discarding a seatbelt retractor assembly or scrapping the entire car damaged by a collision, consult your SUBARU deal- D Tampering with or disconnecting the system’s wiring could re- sult in accidental activation of the seatbelt pretensioner and/or airbag or could make the system inoperative, which may result in serious injury.
Page 57: Child Restraint Systems
D Installation of a tire of different size and construction from the tires specified on the tire placard attached to the door jamb. Always consult your SUBARU dealer if you want to install any acces- sory parts to your vehicle.
Page 58 For that reason, be sure to secure ALL types of child restraint devices (including forward facing child seats) in the REAR seats at all times. You should choose a restraint device which is appropriate for the child’s age, height and weight. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions.
Page 59 WARNING D Child restraint systems and seatbelts can become hot in a ve- hicle that has been closed up in sunny weather; they could burn a small child. Check the child restraint system before you place a child in it. D Do not leave an unsecured child restraint system in your vehi- cle.
Page 60 CAUTION When you install a child restraint system, follow the manufactur- er’s instructions supplied with it. After installing the child re- straint system, check to ensure that it is held securely in posi- tion. If it is not held tight and secure, the danger of your child suffering personal injury in the event of an accident may be in- creased.
Page 61 8. To remove the child restraint system, press the release button on the seatbelt buckle and allow the belt to retract completely. The belt will return to the ELR mode. If you have any question concerning this type of child restraint sys- tem, ask your SUBARU dealer. – CONTINUED – 1-37...
Page 62 B Installation of child restraint systems by use of lower and teth- er anchorages Some types of child restraint systems can be installed on the rear seat of your vehicle without use of the seatbelts. Such child restraint systems are secured to the dedicated anchorages provided on the vehicle body.
Page 63 You will find marks “Child” at the bottom of the rear seat seatbacks. These marks indicate the positions of the lower anchorages (bars). Each lower anchorage is located where the seat cushion meets the seatback. CAUTION When you install a child restraint system, follow the manufactur- er’s instructions supplied with it.
Page 64: Top Tether Anchorages
4. Before seating a child in the child restraint system, try to move seat back and forth to verify that it is held securely in position. If you have any question concerning this type of child restraint sys- tem, ask your SUBARU dealer. J Top tether anchorages B Anchorage location...
Page 65 B To hook the top tether n Sedan CAUTION When the child restraint system is to be secured using the top tether, always pass the top tether under the headrest between the headrest stay posts. If the top tether is routed over the headrest, it may not be properly tensioned, resulting in an unsteady child restraint system.
Page 66 3. Tighten the top tether securely. 4. Reinstall the headrest in such a way that the top tether is routed between the headrest stay posts. n Station wagon CAUTION Always remove the headrest when mounting a child restraint sys- tem with a top tether. Otherwise, it may happen that the top tether cannot be fastened tightly.
Page 67: Srs Airbag (Supplemental Restraint System Airbag)
ton. Store the headrest in the cargo area. Avoid placing the headrest in the passenger compartment to prevent it from being thrown around in the passenger compartment in a sudden stop or a sharp turn. 2. Fasten the top tether hook of the child restraint system to the ap- propriate upper anchorage.
Page 68 Not wearing a seatbelt increases the chance of severe injury or death in a crash even when the car has the SRS airbag. For instructions and precautions concerning the seatbelt system, see the “Seatbelts” sections in this chapter. D Do not sit or lean unnecessarily close to the SRS airbag. Be- cause the SRS airbag deploys with considerable speed –...
Page 69 (including those in child seats and those that have outgrown child restraint devices) sit in the REAR seat properly restrained at all times in a child restraint device or in a seatbelt, whichever is appropriate for the child’s age, height and weight. Secure ALL types of child restraint devices (including forward facing child seats) in the REAR seats at all times.
Page 70 CAUTION D When the SRS airbag deploys, some smoke will be released. This smoke could cause breathing problems for people with a history of asthma or other breathing trouble. If you or your pas- sengers have breathing problems after SRS airbag deploys, get fresh air promptly.
Page 71 B Components Airbag control module (including impact sensors) Airbag module (driver’s side) Airbag module (passenger’s side) Front sub sensor (left hand side) Front sub sensor (right hand side) Seatbelt pretensioner (driver’s side) Seat, seatbelt and SRS airbags Seatbelt pretensioner (passenger’s side) Side airbag module (driver’s side —...
Page 72: Srs Frontal Airbag
J SRS frontal airbag WARNING D NEVER INSTALL A REARWARD FACING CHILD SAFETY SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. D Never allow a child to stand up, or to kneel on the front pas- senger’s seat, or never hold a child on your lap or in your arms.
Page 73 Never hold a child on your lap or in your arms. Adjust the seatback to upright position. Sit well back and upright. Move the seat as far back as possible. WARNING D Do not put any objects over the steering wheel pad and dash- board.
Page 74 The driver’s SRS frontal airbag is stowed in the center portion of the steering wheel. The passenger’s SRS frontal airbag is stowed near the top of the dashboard under an “SRS AIRBAG” mark. In a moderate to severe frontal collision, the driver’s and front passen- ger’s SRS frontal airbags deploy and supplement the seatbelts by reduc- ing the impact on the driver’s and front passenger’s head and chest.
Page 75 Driver’s side SRS airbags deploy as soon as a collision occurs. After deployment, SRS airbags start to deflate immediately so that the driver’s vision is not obstructed. The SRS airbag can function only when the ignition switch is in the “ON”...
Page 76 When the SRS airbag deploys, a sudden, fairly loud inflation noise will be heard and some smoke will be released. These occurrences are normal result of the deployment. This smoke does not indicate a fire in the vehicle. The SRS frontal airbag is designed to deploy in the event of an acci- dent involving a moderate to severe frontal collision.
Page 77 n Examples of the types of accidents in which it is possible that the SRS frontal airbag will deploy. The SRS frontal airbag may be activated when the vehicle sustains a hard impact in the undercarriage area from the road surface (such as when the vehicle plunges into a deep ditch, is severely bumped or knocked hard against an obstacle on the road such as a curb).
Page 78 n Examples of the types of accidents in which the SRS frontal airbag will basically not deploy. The SRS frontal airbag is basically not designed to deploy if the vehicle is struck from side or from behind, or if it rolls onto its side or roof, or if it is involved in a low-speed frontal collision.
Page 79: Srs Side Airbag (If Equipped)
Seat, seatbelt and SRS airbags J SRS side airbag (if equipped) WARNING D The SRS side airbag is designed as only a supplement to the primary protection provided by the seatbelt. It does not do away with the need to fasten seatbelts. It is also important to wear your seatbelt to help avoid injuries that can result when an occupant is not seated in a proper upright position.
Page 80 Do not sit or lean unnecessary close to the front door. Never allow a child to kneel on the front passenger’s seat facing the side window. WARNING D Do not attach accessories to the door trim or near either SRS side airbags and do not place objects near the SRS side airbags.
Page 81 Do not put any kind of cover over either seatback. The SRS side airbag is stored in the door side of each front seatback, which bears an “SRS AIRBAG” label. In a moderate to severe side impact collision, the SRS side airbag on the impacted side of the vehicle deploys between the occupant and the door panel and supplements the seatbelt by reducing the impact on the occupant’s chest.
Page 82 SRS side airbag deploys as soon as a collision occurs. After deployment, SRS side airbag starts to deflate immedi- ately. The SRS side airbag can function only when the ignition switch is in the “ON” position. The driver’s and front passenger’s SRS side airbags deploy indepen- dently of each other since each has its own impact sensor.
Page 83 Seat, seatbelt and SRS airbags When the SRS side airbag deploys, a sudden, fairly loud inflation noise will be heard and some smoke will be released. These occur- rences are normal result of the deployment. This smoke does not indi- cate a fire in the vehicle.
Page 84 n Examples of the types of accidents in which the SRS side air- bag is unlikely to deploy. There are many types of collisions which might not necessarily require SRS side airbag deployment. In the event of accidents like those illus- trated below, the SRS side airbag may not deploy depending on the level of accident forces involved.
Page 85 Seat, seatbelt and SRS airbags n Examples of the types of accidents in which the SRS side air- bag will basically not deploy. The SRS side airbag is basically not designed to deploy if the vehicle is involved in a frontal collision or is struck from behind. Examples of such accidents are illustrated below.
Page 86: Srs Airbag System Monitors
D All related wiring In the event of a malfunction indicated by any of following, the vehicle should be taken promptly to your nearest SUBARU dealer to have the system checked. Unless checked and repaired, the SRS airbags will not...
Page 87: Srs Airbag System Servicing
CAUTION If you need service or repair in areas listed below, we recommend that you have an authorized SUBARU dealer perform the work. The SRS airbag control module, impact sensors and airbag modules are stored in these areas.
Page 88: Precautions Against Vehicle Modification
When the components of the SRS airbag system are replaced, use only genuine SUBARU parts. To ensure their long-term reliability, the SRS airbags must be inspected by a SUBARU dealer ten years after the date of manufacture, which is shown on the certification label attached to the driver’s door. NOTE In the following cases, contact your SUBARU dealer as soon as pos- sible.
Page 89 D Attachment of any equipment (side steps or side sill protec- tors, etc.) other than SUBARU genuine accessory parts to the side body (only for vehicles with side airbags). Always consult your SUBARU dealer if you want to install any accessory parts to your vehicle. Seat, seatbelt and SRS airbags –...
Page 90 Keys and doors Keys ................Door locks .
Page 91: Keys
Keys Master key Submaster key Three types of keys are provided for your vehicle. Master key, submaster key and valet key. The master key and submaster key fit all locks on your vehicle. D Ignition switch D Doors D Trunk (sedan) or Rear gate (station wagon) D Glove compartment The valet key fits only the ignition switch and door locks.
Page 92: Keys And Doors
Keys and doors Door locks B Locking and unlocking from the outside n For vehicles with power door locking switches OM-H2394 To lock the door from the outside with the key, turn the key toward the rear. To unlock the door, turn the key toward the front. Lift the outside door handle to open an unlocked door.
Page 93 locked at the same time. Always make sure that all doors and the rear gate are locked before leaving your vehicle. NOTE Make sure that you do not leave the key inside the vehicle before locking the doors from the outside without the key. n For vehicles without power door locking switches OM-H2394 To lock the door from the outside with the key, turn the key toward the...
Page 94 door. To lock the rear door from the outside without the key, rotate the lock lever rearward and then close the door. Always make sure that all doors and the rear gate (station wagon) are locked before leaving your vehicle. NOTE Make sure that you do not leave the key inside the vehicle before locking the doors from the outside without the key.
Page 95: Power Door Locking Switches (If Equipped)
Pull the inside door handle to open an unlocked door. Always make sure that all doors and the rear gate (station wagon) are closed and locked before starting to drive. J Power door locking switches (if equipped) All doors and the rear gate (station wagon) can be locked and unlocked by the power door locking switches located at the driver’s side and the front passenger’s side doors.
Page 96: Keyless Entry System (If Equipped)
Keyless entry system (if equipped) CAUTION D Do not expose the transmitter to severe shocks, such as those experienced as a result of dropping or throwing. D Do not take the transmitter apart except when replacing the battery. D Do not get the transmitter wet. If it gets wet, wipe it dry with a cloth immediately.
Page 97 HB1000BD B Locking the doors Briefly press the “LOCK/ARM” button (for less than two seconds) to lock all doors (and rear gate on the station wagon). The horn will sound one time. If any of the doors (or the rear gate) is not fully closed, the horn will sound three times to alert you that the doors (or the rear gate) are not properly closed.
Page 98 If the “LOCK/ARM” button is pressed before 30 seconds have elapsed, these lights will go out. Also, these lights will go out if the key is inserted in the ignition switch. The interior light must be set to the middle position in order for this function to operate. B Sounding a panic alarm To activate the alarm, keep the “LOCK/ARM”...
Page 99 To replace the battery: 1. Remove the two screws on the back of the transmitter case by using a phillips screwdriver. 2. Separate the case. 3. Remove the old battery from the holder. 4. Replace with a new battery (Type CR2032 or equivalent) making sure to install the new battery with the positive (+) side facing up.
Page 100 To enter the programming mode: Press to dis- arm the security system (if so equipped). 1. Disarm the security system. (if your vehicle is equipped with the optional security system.) 2. Open the driver’s door and sit in the driver’s seat. 3.
Page 101 To program the transmitters: Press any button. HB1005BB HB1000DB 1. Open the driver’s door. 2. Close the driver’s door. 3. Press and release any button on the transmitter that you wish to program into the system. The horn will sound two times to indicate that the transmitter has been programmed.
Page 102: Security System (If Equipped)
times. If you have two current transmitters, program each one twice. If you have three current transmitters, program two of them once and the third one twice. This process will leave only current transmitter codes in the system’s memory. NOTE Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters.
Page 103 and alarm. In warning mode, the alarm detects lower level vibrations and triggers 2 warning chirps on the horn and two flashes on the lights as a deterrent to would be vandals. In alarm mode, higher lev- els of shock are detected and the system will go into full alarm. D Ignition switch being turned on while in armed state.
Page 104 Keys and doors seconds). If any of the doors, (rear gate or trunk lid) is not fully closed, the horn sounds three times, the parking lights flash three times and the indi- cator light flashes rapidly to alert you that the doors (or the rear gate) are not properly closed.
Page 105 B Disarming the system Briefly press the “UNLOCK/DISARM” button (for less than two seconds) on the remote transmitter. The driver’s door will unlock, the horn will sound two times, the parking lights will flash two times and the indicator light will go off. To unlock all doors (and the rear gate on the station wagon), briefly press the “UNLOCK/DISARM”...
Page 106 second indicating that the system is in the valet mode. To exit valet mode, open the driver’s door and keep the “UNLOCK/ DISARM” button pressed for more than two seconds. The indicator will stop flashing. B Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically accomplished without using the remote transmitter.
Page 107 2. Connect the white (1 pole) connector. 3. Turn the ignition switch from the “LOCK” to the “ON” position. 4. Install the side sill cover. To place the system in active arming mode (remote required for ac- tivation), disconnect the white connector. n Arming the system CAUTION In passive mode, the system will automatically activate the alarm...
Page 108 Keys and doors In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door lock switch is used to lock the vehicle, arm- ing will take place immediately regardless of whether or not the pas- sive mode has been selected.
Page 109: Child Safety Locks
Child safety locks WARNING Always use the child safety lock whenever a child rides in the rear seat. Serious injury could result if a child accidentally opened the door and fell out. Each rear door has a child safety lock that prevents the doors from being opened even if the inside door handle is pulled.
Page 110: Windows
Windows J Power windows WARNING D When operating power windows, be extremely careful to pre- vent anyone’s fingers, arms or head from being caught in the window. D Always lock the passengers’ windows using the lock switch when children are riding in the vehicle. D Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle.
Page 111 HB2008DB All door windows can be controlled by the power window switch clus- ter at the driver side door. n Operating the driver’s window AUTO switch: This switch has two functions. Push the switch down until it clicks and release it, and the window will fully open.
Page 112 Keys and doors B Passengers’ side switches HB2009CB HB2005BB To open the window, push the switch down and hold it until the win- dow reaches the desired position. To close the window, pull the switch up and hold it until the window reaches the desired position. When the lock switch on the power window switch cluster, located on the driver’s side door, is in the “LOCK”...
Page 113: Trunk Lid (Sedan)
Trunk lid (Sedan) WARNING D To prevent dangerous exhaust gas from entering the vehicle, always keep the trunk lid closed while driving. D Help prevent young children from locking themselves in the trunk. When leaving the vehicle, either close all windows and lock all doors or cancel the inside trunk lid release.
Page 114 B To open the trunk lid from inside Pull the trunk lid release lever upward. B To cancel the trunk lid release The inside trunk lid release can be cancelled to help prevent unautho- rized entry into the trunk. To cancel the trunk lid release, set the lid release cancel lever (located on the inside of the trunk lid, mounted to the trunk lid latch) to the “CANCEL”...
Page 115: Internal Trunk Lid Release Handle
J Internal trunk lid release handle The internal trunk lid release handle is a device designed to open the trunk lid from inside the trunk. In the event children or adults become locked inside the trunk, the handle allows them to open the lid. The han- dle is located on the inside of the trunk lid.
Page 116 To open the trunk lid from inside the trunk, press the yellow handle down- ward as indicated by the arrow on the handle. This operation unlocks the trunk lid. Then, push up the lid. The handle is made of material that remains luminescent for approxi- mately an hour in the dark trunk space after it is exposed to ambient light even for a short time.
Page 117 HG2018BA If the latch is not released, contact your SUBARU dealer. In that case, use the key to release the latch, then close the trunk lid. Also, if the movements of the release handle feel restricted or not en- tirely smooth during operation, or the handle and/or handle base is cracked, contact your SUBARU dealer.
Page 118: Rear Gate (Station Wagon)
Rear gate (Station wagon) WARNING To prevent dangerous exhaust gas from entering the vehicle, always keep the rear gate closed while driving. To unlock the rear gate, insert the key in the keyhole and turn it clock- wise. To lock the rear gate, insert the key in the keyhole and turn it coun- terclockwise.
Page 119: Moonroof (If Equipped)
Moonroof (if equipped) WARNING D Never let anyone’s hands, arms, head or any objects protrude from the moonroof. D Before closing the moonroof, make sure that no one’s hands, arms, head or other objects will be accidentally caught in the moonroof.
Page 120 Keys and doors Release the switch after the moonroof has been raised or has been lowered completely. Pushing the switch continuously may cause dam- age to the moonroof. B To open or close the moonroof Push the “Open/Close” switch rearward to open the moonroof. The sun shade will be also opened together with the moonroof.
Page 121: Dual Moonroofs (Station Wagon)
J Dual moonroofs (Station wagon) HB2029AA HB2030AA The front moonroof has a tilting function and the rear moonroof has a sliding function. Both moonroofs operate only when the ignition switch is in the “ON” posi- tion. HB2006BB To open the moonroof(s) 1.
Page 122 Keys and doors 4. To fully open it, release the switch once, then push the rear side of the switch again and keep it depressed until the full open position is reached. To close the moonroof(s) 1. Push the front side (CLOSE) of the switch. The rear moonroof will slide to close together with the rear sunshade while the switch is being pressed, then stop automatically at a position 5.9 in (15 cm) away from the fully closed position.
Page 123 B Sun shades OM-H2355 n Front sun shade The front sun shade can be slid forward or backward by hand regard- less of the moonroof position. n Rear sun shade The rear sun shade can be slid forward or backward by hand while the rear moonroof is closed.
Page 124 Instruments and controls Ignition switch ............. Key reminder chime .
Page 125 Fog light switch (if equipped) Wiper and washer Windshield wiper and washer switches Rear window wiper and washer switch (if equipped) Rear window defogger switch Windshield wiper deicer (if equipped) Mirrors ............... . Inside mirror .
Page 126: Instruments And Controls
Ignition switch WARNING Never turn the ignition switch to “LOCK” while the vehicle is be- ing driven or towed because that will lock the steering wheel, pre- venting steering control. And when the engine is turned off, it takes a much greater effort than usual to steer. The ignition switch has four positions: LOCK, ACC, ON and START.
Page 127 n Automatic transmission vehicles HB4016BA HB2032CA The key can be turned from “ACC” to “LOCK” only when the selector lever is in the “P” position. n Manual transmission vehicles OM-H0144 The key can be turned from “ACC” to “LOCK” only when the key is pushed in while turning it.
Page 128: Key Reminder Chime
B START CAUTION Do not turn the ignition switch to the “START” position while the engine is running. The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON”...
Page 129: Key Interlock Release (At Vehicles Only)
2. Remove the cover under the steering column using a phillips screwdriver. 3. Turn the ignition key while pressing the key interlock release lever. Take your vehicle to the nearest SUBARU dealer immediately to have the key interlock system repaired. HB3011BA...
Page 130: Hazard Warning Flasher
Hazard warning flasher The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works with the ignition switch in any position. To turn on the hazard warning flasher, push the hazard warning button on the instrument panel.
Page 131 B Odometer The odometer shows the total distance that the vehicle has been driv- B Double trip meter The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of the knob changes the function in the following order.
Page 132: Tachometer
J Tachometer CAUTION Do not operate the engine with the pointer of the tachometer in the red zone. In this range, fuel injection will be cut by the engine control module to protect the engine from overrevving. The engine will resume running normally after the engine speed is reduced below the red zone.
Page 133: Temperature Gauge
J Temperature gauge CAUTION If the pointer exceeds the normal operating range, safely stop the vehicle as soon as possible. See “In case of emergency” in chapter 9. The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position. The coolant temperature will vary in accordance with the outside temper- ature and driving conditions.
Page 134: Seatbelt Warning Light And Chime
If any lights fail to come on, it indicates a burned-out bulb or a malfunc- tion of the corresponding system. Consult your authorized SUBARU dealer for repair. J Seatbelt warning light and chime When the ignition switch is turned to the “ON” position, the seatbelt warning light will come on and the reminder chime will sound for about six seconds to remind the driver to fasten the seatbelt.
Page 135 Tightening the cap will not make the CHECK ENGINE warning light turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your authorized SUBARU dealer immediately. B If the light is blinking:...
Page 136: Charge Warning Light
If the oil level is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately.
Page 137: At Oil Temperature Warning Light (For At Vehicles)
If the light flashes after the engine starts, it may indicate that the auto- matic transmission control system is not working properly. Contact your nearest SUBARU dealer for service immediately. J ABS warning light The ABS warning light comes on when the ignition switch is turned to the “ON”...
Page 138: Vdc (Vehicle Dynamics Control) Warning Light (If Equipped)
VDC system is operational. The VDC system is probably inoperative under any of the following conditions. Immediately have your vehicle checked at a SUBARU dealer. D The VDC warning light does not come on when the ignition switch is turned to the “ON”...
Page 139: Brake System Warning Light
D Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains on, have the brakes inspected by a SUBARU dealer immediately. D If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle.
Page 140: Door Open Warning Lights
“ON”), it could be an indication of leaking of brake fluid or worn brake pads. Have your vehicle checked by a SUBARU dealer immediately. J Door open warning lights The specific door open warning light comes on if any door or the rear gate is not fully closed.
Page 141: Vdc (Vehicle Dynamics Control) Off Indicator Light (If Equipped)
CHECK ENGINE warning light is on. The VDC system is probably faulty under any of the following conditions. Have your vehicle checked at a SUBARU dealer as soon as possible. D The VDC OFF indicator light does not come on when the ignition switch is turned to the “ON”...
Page 142: High Beam Indicator Light
“Replacing bulbs” section in chapter 11. J High beam indicator light This light shows that the headlights are in the high beam mode. This indicator light also comes on when operating headlight flasher. Clock To set the time, turn the setting knob clockwise to advance and counter- clockwise to retard the time.
Page 143 The light switch operates only when the ignition switch is in the “ON” position. B Headlights To turn on the headlights, turn the knob on the end of the turn signal lever. first position Parking lights, instrument panel illumination, tail lights and license plate light are on.
Page 144: Daytime Running Light System
To flash the headlights, pull the lever toward you and then release it. The high beam will stay on for as long as you hold the lever. The headlight flasher works even though the lighting switch is in the “OFF” position.
Page 145: Illumination Brightness Control
ished, the lever will return automatically. If the lever does not return after cornering, return the lever to the neutral position by hand. To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction of the turn or lane change.
Page 146: Parking Light Switch
Parking light switch The parking light switch operates regardless of the ignition switch posi- tion. By pushing the front end of this switch, following lights will come on. – Parking lights – Front and rear side marker lights – Tail lights –...
Page 147: Fog Light Switch (If Equipped)
Fog light switch (if equipped) The fog lights operate only when the headlights are on low beam. Push the fog light switch to turn the fog lights on. Press the switch again to turn them off. The indicator light located on the switch will illuminate when the fog lights are on.
Page 148 D Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. (See “Windshield washer fluid” section in chapter 11.) Also, when driving the vehicle when there are freezing tempera- tures, use non-freezing type wiper blades.
Page 149: Windshield Wiper And Washer Switches
windshield or rear window. D Grease, wax, insects or other material on the windshield or the wiper blades results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer surface of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner.
Page 150 B Wiper intermittent time control (if equipped) When the wiper switch is in the “ the operating interval of the wiper. The operating interval can be adjusted continuously from the shortest interval to the longest. Two click stop positions of the dial may help you to aim at your de- sired interval.
Page 151: Rear Window Wiper And Washer Switch (If Equipped)
er control lever. The washer fluid sprays until you release the washer button. The wipers operate while you push the button. J Rear window wiper and washer switch (if equipped) HB2021BC B Rear wiper The rear wiper offers intermittent operation only. To turn the rear wiper on, turn the knob on the end of the wiper control lever upward.
Page 152: Rear Window Defogger Switch
Rear window defogger switch CAUTION D Do not use sharp instruments or window cleaner containing abrasives to clean the inner surface of the rear window. They may damage the conductors printed on the window. D To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary.
Page 153: Windshield Wiper Deicer (If Equipped)
B For vehicles with automatic climate control To turn on the defogger, push the switch. To turn it off, push the switch again. The indicator light “u” lights up on the climate control display panel while the rear window defogger is operating. Windshield wiper deicer (if equipped) CAUTION To prevent the battery from being discharged, do not operate the...
Page 154: Mirrors
Instruments and controls The windshield wiper deicer operates only when the ignition switch is in the “ON” position. Before turning on the windshield wiper deicer, remove any snow from the windshield. To turn on the windshield wiper deicer, push the switch. The indicator light located on the switch lights up while the windshield wiper deicer is operating.
Page 155 B Compass mirror (if equipped) HB6019BB The inside electronic compass mirror has an anti-glare feature which automatically reduces glare coming from headlights of vehicles be- hind you. It also contains a built-in compass. D By pressing and releasing the left button, the automatic dimming function is toggled on or off.
Page 156 Instruments and controls n Photosensors HB6020BA The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded.
Page 157: Outside Mirrors
n Compass zone adjustment 1. The zone setting is factory preset to Zone 8. Refer to the “Com- pass calibration zone” map shown above or one attached to the end of this manual to verify that the compass zone setting is correct for your geographical location.
Page 158 Instruments and controls B Adjusting mirrors To adjust the mirrors by hand, push where indicated by the arrows. OM-H2737 B Remote control mirror switch (if equipped) The remote control mirrors operate only when the ignition switch is in the “ON” or “ACC” position. HB4004BB 1.
Page 159: Tilt Steering Wheel
B Outside mirror defogger (if equipped) CAUTION To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary. The outside mirror defogger operates only when the ignition switch is in the “ON” or “ACC” position. To turn on the outside mirror defogger, push the switch while the en- gine is running.
Page 160: Horn
Instruments and controls HB4002BA 1. Adjust the seat position. Refer to the “Front seat” section (chapter 1). 2. Pull the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Push the lever up to lock the steering wheel in place. 5.
Page 161 Climate control Ventilator ..............Manual heating and air conditioning system Heater operation .
Page 162: Ventilator
Ventilator B Center and side ventilators B Adjustable side defroster grille (for driver’s side only) Normal position Side defroster grille The driver’s side defroster grille is adjustable. The normal position as shown in the diagram directs warm air to the side glass. When more rapid defrosting of the windshield is desired, the air flow can be directed temporarily toward the windshield to assist the windshield defroster.
Page 163: Climate Control
Climate control B Air flow selection HB5006BA HB5006CA HB5006DA HB5006EA HB5006FA – CONTINUED –...
Page 164: Manual Heating And Air Conditioning System
Manual heating and air conditioning system B Control panel 1. Temperature control dial 2. Fan speed control dial 3. Air flow control dial 4. Air conditioner button 5. Air inlet selection button 6. Rear window defogger button (Refer to “Rear window defogger” in chapter 3.) n Temperature control dial This dial regulates the temperature of air flow from the air outlets over...
Page 165 : Air flows through the foot outlets and some through the wind- shield defroster outlets. : Air flows through the windshield defroster outlets and foot outlets. : Air flows through the windshield defroster outlets. NOTE When the dial is placed in the “ conditioner compressor operates automatically regardless of the position of the air conditioner button to defog the windshield quickly.
Page 166 n Air inlet selection button WARNING Continued operation in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condi- tion clears. ON position (Recirculation): Interior air is recirculated inside the ve- hicle.
Page 167: Heater Operation
Climate control J Heater operation B Defrosting or defogging the windshield HB5011AA To direct warm air to the windshield and front door windows: 1. Set the air flow control dial to the “ ” position. 2. Turn the temperature control dial all the way to the right. 3.
Page 168 To direct warm air toward the floor and the windshield: 1. Set the air flow control dial to the “ 2. Set the temperature control dial to the most comfortable level. 3. Set the fan speed control dial to the desired speed. NOTE Warm air also comes out from the right and left air outlets.
Page 169 B Bi-level heating This setting allows you to direct air of different temperatures from the instrument panel and foot outlets. The air from the foot outlets is slightly warmer than from the instrument panel outlets. 1. Set the air inlet selection button to the “OFF” position. 2.
Page 170: Air Conditioner Operation
To force outside air through the instrument panel outlets: 1. Set the air inlet selection button to the “OFF” position. 2. Set the air flow control dial to the “ 3. Set the temperature control dial all the way left. 4.
Page 171 Climate control 1. Set the air inlet selection button to the “OFF” position. 2. Set the air flow control dial to the “ ” position. 3. Set the air conditioner button to the “ON” position. 4. Set the temperature control dial to the blue area. 5.
Page 172: Automatic Climate Control System (If Equipped)
Automatic climate control system (if equipped) NOTE D Operate the automatic climate control system when the engine is running. D When the engine coolant is cold, for instance in cold weather, the air flows through the windshield defroster outlets and the blower runs at the lowest speed to prevent cold air from blowing directly against the driver and front passenger.
Page 173 Climate control B Control panel HB4031BB 1. AUTO switch 2. OFF switch/BRIGHT 3. Outside air temperature switch 4. Defroster switch 5. Rear window defogger switch (Refer to the “Rear window defog- ger” in chapter 3.) 6. Fan speed control switch 7.
Page 174 ECON (economy) mode: When you press the “AUTO” switch while the system is in the AUTO mode, it selects the ECON (economy) mode, turning on the ECON “ ” indicator light. In the ECON mode, the compressor runs to be thrifty with energy consumption. Interior windows tend to fog in this energy-saving operation.
Page 175 n OUT.TEMP switch To check the outside air temperature, push the “OUT.TEMP” switch. The outside air temperature will be displayed for five seconds, and then the display automatically changes back to the inside air temper- ature. The display changes over from the inside air temperature to the out- side air temperature as its normal indication if you keep the switch pressed for more than 2 seconds.
Page 176 — Fan speed control switch HB5021BB The fan speed control switch has the 5 positions: AUTO position and 4 different fan speed positions. With the fan speed control switch in the AUTO position, the fan speed changes automatically corresponding to various conditions: air tem- perature inside and outside of the passenger compartment, intensity of the sunlight, etc.
Page 177 n MODE — Air flow control switch (Ventilation) : Air flows through the instrument panel outlets. (Bi-level) : (Heat) : (Heat-def) : n Air inlet selection switch WARNING Continued operation in the “ dows. Switch to the “ dusty condition clears. Select the air inlet by pushing the air inlet selection switch.
Page 178 : Outside air is drawn into the passenger compartment. When the air conditioning system is operated in the “AUTO” mode, this position is selected automatically. The indicator light “ ” on the control panel comes on when this switch is pushed.
Page 179 B Temperature sensors This Automatic Climate Control system employs the several sensors. These are very delicate parts. Therefore, if these sensors are dam- aged, it is possible that the Automatic Climate Control system will not properly control the air temperature in the passenger compartment. To prevent possible damage to the sensors, please observe the fol- lowing: –...
Page 180: Operating Tips For Heater And Air Conditioner
B Checking air conditioning system before summer season Check the air conditioner unit for refrigerant leaks, hose conditions, and proper operation each spring. This check is best performed by your SUBARU dealer. 4-20...
Page 181: Air Filtration System (If Equipped)
Your air conditioner uses ozone friendly refrigerant HFC134a. There- fore, the method of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
Page 182 Audio Antenna system ............Installation of accessories Audio set .
Page 183: Antenna System
Antenna system B Printed antenna CAUTION Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the window on which the antenna is printed. Doing so may damage the antenna printed on the window. The antenna is printed on the inside of the rear window glass (sedan) or the left side rear quarter window glass (station wagon).
Page 184: Audio
Audio set Your SUBARU may be equipped with one of the following audio sets. See the pages indicated in this section for operating details. B Type A and type B audio set...
Page 185 B Type C audio set D Radio operation: refer to page 5-20 D Cassette player operation: refer to page 5-25 D CD (compact disc) player operation: refer to page 5-28 D CD changer control: refer to page 5-31 B Type D and type E audio set D Radio operation: refer to page 5-34 D CD (compact disc) player operation: refer to page 5-38 D CD changer control: refer to page 5-41...
Page 186 B Type F audio set D Radio operation: refer to page 5-44 D Cassette player operation: refer to page 5-48 D CD player control: refer to page 5-49 B McIntosh audio set D Radio operation: refer to page 5-50 D Cassette player operation: refer to page 5-55 D CD player operation: refer to page 5-57 Audio HB5043AA...
Page 187 B CD player 1 (Optional audio unit — if equipped) D Inserting and removing a disc: refer to page 5-60 B CD player 2 (Optional audio unit — if equipped) D CD (compact disc) player operation: refer to page 5-62 HB5039AA HB5044AA...
Page 188 Audio B In-dash 6 CD auto changer (Optional audio unit — if equipped) HB5040AA D Inserting and removing a disc or all discs: refer to page 5-65 – CONTINUED –...
Page 189: Type A And B Audio Set (If Equipped)
Type A and B audio set (if equipped) Type A: Without weather band Type B: With weather band The audio set will operate only when the ignition switch is in the “ACC” or “ON” position. Radio operation Power switch/Volume, Tone, Balance, Fader control dial AUDIO button BAND button...
Page 190 n Tone and balance control (AUDIO) The volume control dial This dial becomes a control for Bass, Treble, Fader or Balance when you select the appropriate tone and balance control mode. Choose desired volume level for each mode by turning the volume control dial.
Page 191 B Waveband selection n FM/AM selection Push the “BAND” button display indicates which one is currently selected. n FM/AM/Weather band selection Push the “BAND” button (WB) reception. The display indicates which is currently selected. B Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.
Page 192 Audio Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function properly if the station reception is weakened by distance from the station or proximity to tall buildings and hills.
Page 193: Cassette Player Operation
Cassette player operation Cassette slot Eject button TAPE button TPS (Tape Program Search) Repeat button NOTE D Only use good quality cassettes (cassettes longer than C-90 are not recommended). D Put cassettes back in their boxes immediately after use to protect them from dust and dirt and to prevent the tape from unwinding.
Page 194 B Tape travel indicators These indicate the direction the cassette tape is moving. " : Indicates that the top side of the cassette is being played back. A : Indicates that the bottom side of the cassette is being played back.
Page 195 To use this function, press the “TPS” button to turn on the “TPS” indi- cator. If the fast-forward button “FF” is then pressed, the player ad- vances the tape to the beginning of the next selection and starts play- ing it. If the rewind button “REW” is pressed instead, the player rewinds the tape to the beginning of the current selection and starts replaying it.
Page 196 CD player control (If optional CD player is connected) An optional CD player can be connected to this audio unit. See your SUBARU dealer for more information. For procedures for loading and un- loading CDs, refer to “CD player 1” in this chapter.
Page 197 NOTE D If the “CD” button is pressed during a radio broadcast, the disc will interrupt the broadcast. D After playback on the last song finishes, the player will auto- matically return to track 1 (the first song on the disc). B To select a song from its beginning Briefly press the “""...
Page 198 CD changer control (If optional in dash CD changer is connected) An optional CD changer can be connected to this audio unit. See your SUBARU dealer for more information. For procedures for loading and un- loading CDs, refer to “In-dash 6 CD auto changer” in this chapter. CD button...
Page 199 NOTE D If the “CD” button is pressed during a radio broadcast, the CD changer will interrupt the broadcast. D At the end of the disc, playback automatically continues with the next disc. D After playback on the last disc finishes, the player will auto- matically return to the first disc.
Page 200 all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal playback mode is restored. B Scan (a convenient way to become familiar with a disc) 1.
Page 201: Type C Audio Set (If Equipped)
Type C audio set (if equipped) The radio will operate only when the ignition switch is in the “ACC” or “ON” position. Radio operation FM/AM selection button SCAN button WB (weather band) button Tuning buttons Preset buttons B Power switch and volume/bass/treble/fader/balance control (PWR/VOL) The dial is used for both power (ON/OFF) and volume control.
Page 202 This dial is used for bass/middle/treble controls when the “AUDIO” button is in the depressed position. It is also used for fader/balance controls when the “FAD/BAL” button Display Control mode Bass control Middle note control Treble control Fader control Balance control Volume control n Tone control The volume control dial...
Page 203 Bass Middle (BAS) (MId) n Fader and balance control The volume control dial dial become the controls for Fader or Balance when you select the appropriate fader and balance control mode. Choose desired setting for each mode by turning the volume control dial.
Page 204 Audio The display indicates which one is currently selected. B Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received. B Weather band button (WB) Push the “WB” button when the radio is off to turn on the radio in the weather band.
Page 205 band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only.
Page 206 Cassette player operation TAPE (cassette player selection) button Cassette slot Eject button TPS button NOTE D Only use good quality cassettes (cassettes longer than C-90 are not recommended). D Put cassettes back in their boxes immediately after use to protect them from dust and dirt and to prevent the tape from unwinding.
Page 207 n When cassette tape is in the player When the “TAPE” button is pressed, the display will show “PLAY” and the player will start playback. B Tape travel indicators These indicate the direction the cassette tape is moving. " : indicates that the top side of the cassette is being played back. A : indicates that the bottom side of the cassette is being played back.
Page 208 n Blank search Press “TPS” button during playback to return to the beginning of the current selection or to skip to the beginning of the next selection. To use this function, press the “TPS” button to turn on the “TPS” indi- cator.
Page 209: Compact Disc Player Operation
* Noise reduction system manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D Symbol are trade marks of Dolby Laboratories Licensing Corporation. B Auto metal sensor The cassette player automatically adjusts for metal or CrO Compact disc player operation SCAN button Disc slot Eject button...
Page 210 After insertion, the DISC indicator “ appear on the display and the player will start playback. NOTE D Make sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off.
Page 211 B Repeat playback Press the “RPT” button while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored.
Page 212 CD changer control (If optional in-dash CD changer is connected) An optional CD changer can be connected to this audio unit. See your SUBARU dealer for more information. For procedures for loading and un- loading CDs, refer to “In-dash 6 CD auto changer” in this chapter. SCAN button...
Page 213 NOTE D If a disc is in the player, the “CD” button is used to change from CD player operation to CD changer operation. Each time the “CD” button is pressed, the operating mode will change alter- nately. D At the end of the disc, the player automatically continues with the next disc.
Page 214 B Fast forwarding and fast reverse n Fast forwarding Press the “"" ” button fast forward the disc. Release the button to stop fast forwarding. If you continue fast forwarding to the end of the disc, the CD changer will automatically stop fast forwarding and start playback beginning with the first track on the current disc.
Page 215: Type D And E Audio Set (If Equipped)
Type D and E audio set (if equipped) Type D: Without weather band Type E: With weather band The audio set will operate only when the ignition switch is in the “ACC” or “ON” position. Radio operation Power switch/Volume, Tone, Balance, Fader control dial BAND button Tuning buttons...
Page 216 n Tone and balance control (AUDIO) The volume control dial This dial becomes a control for Bass, Treble, Fader or Balance when you select the appropriate tone and balance control mode. Choose desired volume level for each mode by turning the volume control dial.
Page 217 B Waveband selection n FM/AM selection Push the “BAND” button display indicates which one is currently selected. n FM/AM/Weather band selection Push the “BAND” button (WB) reception. The display indicates which is currently selected. B Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.
Page 218 Audio Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function properly if the station reception is weakened by distance from the station or proximity to tall buildings and hills.
Page 219 Compact disc player operation Disc slot CD button Eject button Fast forward and track up button B To playback a compact disc n When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position.
Page 220 n When CD is in the player When the “CD” button NOTE After the last song finishes, the player will automatically return to track 1 (the first song on the disc). B To stop playback of a CD When the “PWR” button CD stops playing temporarily.
Page 221 cel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. B Random playback Use this to play the tracks on the disc in random order. During play- back, press the “RDM” button and hold it in for more than 2 se- conds.
Page 222 CD changer control (If optional in dash CD changer is connected) An optional CD changer can be connected to this audio unit. See your SUBARU dealer for more information. For procedures for loading and un- loading CDs, refer to “In-dash 6 CD auto changer” in this chapter. CD button...
Page 223 B Selection of a desired disc Discs cannot be selected using the main audio unit. To select a disc, press one of the “Disc select” buttons (these are numbered from 1 to 6) on the CD changer unit. The disc will begin to play. B To select a song from its beginning Briefly press the “Y”...
Page 224 Audio 2. Press the “SCAN” button again when you hear a track you like. – Normal playback resumes. B To stop playback To stop playback and switch over to the radio mode, press the “BAND” button. – CONTINUED – 5-43...
Page 225: Type F Audio Set (If Equipped)
Type F audio set (if equipped) The audio set will operate only when the ignition switch is in the “ACC” or “ON” positions. Radio operation Tuning buttons SCAN button FM/AM selection button Preset buttons B Power switch and volume/bass/treble/fader/balance control n Power switch and volume control (PWR/VOL) The dial is used for both power (on/off) and volume control.
Page 226 Choose desired volume level for each mode by turning the volume control dial. The control function returns to volume control mode after about 5 seconds. To change control modes: Each brief press of the “AUDIO” button changes control modes in the following sequence starting from vol- ume control mode.
Page 227 B FM/AM selection button (FM/AM) Push the “FM/AM” button when the radio is on to select FM1, FM2 or AM reception. Each time this button is pressed, the band will change in the following order: The display indicates which one is currently selected. B Stereo indicator The stereo indicator “ST”...
Page 228 Audio B Selecting preset stations Presetting a station with a preset button allows you to select that station in a single operation. Up to six AM, FM1 and FM2 stations each may be preset. B How to preset stations 1. Press the “FM/AM” selection button to select FM1, FM2 or AM reception.
Page 229 Cassette player operation Eject button Cassette slot NOTE D Only use good quality cassettes (cassettes longer than C-90 are not recommended). D Put cassettes back in their boxes immediately after use to protect them from dust and dirt and to prevent the tape from unwinding. D Never expose cassettes to heat, direct sunlight or moisture.
Page 230 CD player operation (if optional CD player is connected) An optional CD player can be connected to this audio unit. See your SUBARU dealer for more information. For CD player operation proce- dures, refer to “CD player 2” in this chapter.
Page 231: Mcintosh Audio Set (If Equipped)
McIntosh audio set (if equipped) The audio set will operate only when the ignition switch is in the “ACC” or “ON” positions. CAUTION The power amplifier for this audio set is mounted under the front passenger’s seat. The amplifier will become hot if the audio con- tinues to operate.
Page 232 Audio B ON-OFF switch The audio system can be turned on by pressing the POWER button when the ignition key is in the ACC or ON position. Pressing the POWER button once again will turn off the power. In addition, the fol- lowing six operations will also result in the audio system’s power be- ing turned on: D Pressing the FM/AM selector button...
Page 233 HBS041AA n BASS control The bass control adjusts the level of low pitch sounds. The bass is adjusted by turning the knob from left to right in this condition. Turn clockwise to increase the level of bass tones. Turn counterclockwise to reduce the level of bass tones. n TREBLE control The treble control adjusts the level of high pitch sounds.
Page 234 n FADER control The balance control adjusts the volume balance between the front and rear speakers. The balance is adjusted by turning the knob from left to right in this condition. Turn clockwise to increase the relative sound volume in the front of the vehicle.
Page 235 B Seek tuning (SEEK) If the Tuning dial’s outer tuner is turned for longer than half of a se- cond, the radio will begin to automatically search for receivable fre- quencies and will stop at the first one found. This function may not be available, however, when radio signals are weak.
Page 236 B Weather band button (WB) Push the “WB” button when the radio is off to turn on the radio in the weather band. Press the “WB” button when the radio is on to select the weather band. Cassette player operation Cassette slot Eject button TAPE (cassette player...
Page 237 B Cassette tape stop and eject button When “ ” button is pressed, playback stops and the cassette tape is ejected. Before the ignition switch is turned to the “OFF” position, eject the tape from the player. Always make certain that you remove the cas- sette tape.
Page 238 Compact disc player operation DISC IN indicator light Disc slot Disc button B To play back a compact disc n When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position.
Page 239 D If a disc is inserted during a radio broadcast, the disc will interrupt the broadcast. D After the last song finishes, the disc will automatically return to track 1 (the first song on the disc) and will automatically play back.
Page 240 Audio B Fast forwarding and fast reverse HBS044BA n Fast forward Turn the “FF⋅FB” dial clockwise and hold it continuously for more than 2 seconds to fast forward the disc. Release the knob to stop fast forwarding. n Fast reverse Turn the “FF⋅FB”...
Page 241: Cd Player 1 (If Equipped)
NOTE Avoid driving the vehicle with a CD sticking out, because vibra- tion might make it fall out. CD player 1 (if equipped) Disc slot Disc indicator CAUTION D Use only music CDs identified by D Do not use CDs listed below which could cause damage to the CD player.
Page 242 Audio B To insert a disc Be sure to hold a disc with the label side (the side where titles are printed) up. Push the disc into the slot. The disc will be automatically set in position by the auto-loading mechanism and begin playing.
Page 243: Cd Player 2 (If Equipped)
CD player 2 (if equipped) Compact disc player operation Eject button Repeat/random button Scan/top button Disc slot B To playback a compact disc n When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position.
Page 244 n When CD is in the player When the “"/ ” button NOTE After the last song finishes, the player will automatically return to track 1 (the first song on the disc). B To stop playback of a CD When the “"/ ” button CD stops playing temporarily.
Page 245 cancel the repeat mode, press the button again. Then the “RPT” indi- cator goes out, and normal playback mode is restored. B Random playback Use this to play the tracks on the disc in random order. During play- back, press the “RPT/RDM” button and hold it in for more than 2 seconds.
Page 246: In-Dash 6 Cd Auto Changer (If Equipped)
In-dash 6 CD auto changer (if equipped) Disc slot Disc indicators (disc No.1 to 6) CAUTION D Do not attempt to insert two or more discs into the slot at a time. Doing so can cause mechanical damage to the CD changer. D Use only music CDs identified by a D Do not use CDs listed below which could cause damage to the CD player.
Page 247 B To insert a disc 1. Press one of the “Disc select” buttons (numbered from 1 to 6) for which the disc indicator light is “OFF”. The Disc indicator lights are located directly above the corresponding “Disc select” buttons. 2. The indicator will begin blinking. The blinking will last for 15 se- conds.
Page 248 Audio B To remove all discs at one time 1. Press and hold the “Eject” button until all “Disc” indicators begin blinking (about 1.5 seconds), and the first disc will be ejected. 2. When the disc is removed, the next one will be ejected, and so on. B To replace a playing disc with another Simply press the desired one of “Disc select”...
Page 249: Precautions To Observe When Handling A Compact Disc (Cd)
Precautions to observe when handling a compact disc (CD) Use only compact discs (CDs) that have the mark shown below. CD- RWs cannot be used. Also, some CD-Rs cannot be played. HB5062AA D In cold and/or rainy weather, dew can form inside the CD player, pre- venting normal operation.
Page 250 Audio HB5061BA – CONTINUED – 5-69...
Page 251 Interior equipment Interior light ..............Dome light .
Page 252: Interior Light
Interior light J Dome light HS6003BC The dome light switch has three positions: ON: The light stays on continuously. DOOR (middle position): The light comes on when any of the doors (or the rear gate on the wagon) is opened. The light remains on for several seconds and gradually goes out after all doors (and the rear gate on the wagon) are closed or if the key is inserted in the ignition switch.
Page 253: Interior Equipment
Interior equipment J Cargo area light (if equipped) Cargo area light DOOR HB0377 The cargo area light switch has three positions: ON: The light stays on continuously. OFF: The light stays off. DOOR: The light comes on only when the rear gate is opened. When leaving your vehicle, make sure the light is turned off to avoid bat- tery discharge.
Page 254: Sun Visors
To turn on the spotlight, push the switch. To turn it off, push the switch again. When leaving the vehicle, make sure the light is turned off to avoid bat- tery discharge. Sun visors To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways.
Page 255: Vanity Mirror (If Equipped)
J Vanity mirror (if equipped) To use the vanity mirror, swing down the sunvisor and open the vanity mirror cover. B Vanity mirror with light (if equipped) The light beside the vanity mirror comes on when the ignition switch is either in the “ACC”...
Page 256: Glove Compartment
J Glove compartment Unlock Lock HS0090 To open the glove compartment, pull the handle. To close it, push the lid firmly upward. To lock the glove compartment, insert the key and turn it clockwise. J Center console HB6022BA To open the lid, pull up the lock release. If the console lid is fully opened when a large cup is put in the rear pas- senger’s cup holder, the lid may hit the cup and beverage may be spilled.
Page 257: Coin Tray
J Coin tray To open the coin tray, pull the upper edge of the lid. J Overhead console (if equipped) CAUTION When your vehicle is parked in the sun or a warm day, the inside of the overhead console heats up. Avoid storing plastic or other heat-vulnerable or flammable articles such as a lighter in the overhead console.
Page 258: Cup Holder
Cup holder CAUTION D Do not pick up a cup from the cup holder or put a cup in the holder while you are driving, as this may distract you and lead to an accident. D Take care to avoid spills. Beverages, if hot, might burn you or your passengers.
Page 259: Cigarette Lighter Socket (If Equipped)
CAUTION D The electrical power socket located on the lower part of the instrument panel is originally designed to use a SUBARU genuine cigarette lighter plug. Do not use non-genuine cigarette lighter plugs in the socket. Doing so may cause a short-circuit and over- heating, resulting in a fire.
Page 260 The electrical power socket located on the lower part of the instrument panel can be used as cigarette lighter socket. A cigarette lighter plug is an optional accessory. It is available from your SUBARU dealer. The cigarette lighter socket may also be used as a power source for an in-car use electrical appliance.
Page 261 The cigarette lighter operates only when the ignition switch is in the “ON” and “ACC” positions. To use the cigarette lighter, push in the knob and wait a few moments. It will automatically spring up when ready for use. B Using as an accessory power socket Electrical power (12V DC) from the battery is on tap at the socket when the ignition switch is either in the “ACC”...
Page 262: Ashtray
If you want to use the socket for a cigarette lighter again, or to protect your purchaser before you sell your car, have your SUBARU dealer replace the socket with a new one. Ashtray CAUTION Do not use ashtrays as waste receptacles or leave a lighted ciga- rette in an ashtray.
Page 263: Accessory Power Socket
To remove the ashtray for cleaning, open it and pull it out while pushing the inner plate down. Accessory power socket B In the luggage compartment (if equipped) CAUTION D Do not attempt to use a cigarette lighter in the accessory power socket.
Page 264: Convenience Hook
Electrical power (12V DC) from the battery is on tap at the socket when the ignition switch is either in the “ACC” or “ON” position. You can use an in-car use electrical appliance by connecting it to the socket. NOTE The trim cover has a notch through which the connected electri- cal appliance’s cord can be passed.
Page 265: Floor Mat (If Equipped)
Sedan n For sedan models A shopping bag hook is attached to each inner side wall of the trunk near the trunk lid opening. n For station wagon models A shopping bag hook is attached to each side of the cargo area. To use the hook, push the upper portion and the shopping bag hook will appear.
Page 266: Luggage Cover (If Equipped)
A retaining pin is located on the driver’s side of the vehicle next to the fuel filler door release. The floor mat is secured using the built-in grom- met, by placing the grommet over the pin and pushing downward. Luggage cover (if equipped) WARNING Do not place anything on the extended cover.
Page 267 Interior equipment B Using the cover HB7015BA To extend the cover, pull the end of the cover out of the housing, then insert its hooks into the catches as shown. To rewind it, unhook it from the catches and it will rewind automatically. You should hold on to the cover and guide it back into the cover housing while it is rewinding.
Page 268: Cargo Anchorage Eyelets (If Equipped)
Cargo anchorage eyelets (if equipped) CAUTION The cargo anchorage eyelets are designed only for securing light cargo. Never try to secure cargo that exceeds the capacity of the hooks. The maximum load capacity is 44 lb (20 kg) per eyelet. The cargo area is equipped with four anchorage eyelets so that cargo can be secured with a luggage net or ropes.
Page 269 Interior equipment Sedan HB6007BB HB7019AD HB6008BA The storage tray is located under the floor of the trunk or cargo area and can be used to store small items. To open the lid, pull the tab or handle Station wagon: Hang the hook provided on the underside of the lid on the rear edge of the roof to keep the lid open.
Page 270 Starting and operating Fuel ................Fuel requirements .
Page 271: Fuel
Fuel CAUTION Use of a fuel which is low in quality or use of an inappropriate fuel additive may cause engine damage. J Fuel requirements B 2.5 Liter models The 2.5 Liter engine is designed to operate using unleaded gasoline with an octane rating of 87 AKI or higher.
Page 272: Starting And Operating
California is permitted to have higher sulfur levels, which may affect the performance of your vehicle’s catalytic converter and may pro- duce a sulfur exhaust odor or smell. SUBARU recommends that you try a different brand of unleaded gasoline having lower sulfur to deter- mine if the problem is fuel related before returning your vehicle to an authorized dealer for service.
Page 273: Fuel Filler Lid And Cap
SUBARU dealer. D Fuel system damage or driveability problems which result from the use of improper fuel are not covered under the SUBARU Limited War- ranty. J Fuel filler lid and cap...
Page 274 Fuels may cause paint damage, which is not covered under the SUBARU Limited Warranty. D Always use a genuine SUBARU fuel filler cap. If you use the wrong cap, it may not fit or have proper venting, and your fuel tank and emission control system might be damaged.
Page 275 HB3008BB 2. Remove the fuel filler cap by turning it slowly counterclockwise. 3. Stop filling the tank after the fuel filler pump automatically clicks off. Do not add any more fuel. 4. Put the cap back on, turn it clockwise until you hear a clicking noise.
Page 276: State Emission Testing (U.s. Only)
At state inspection time, remember to tell your inspection or service station in advance not to place your Subaru AWD vehicle on a two- wheel dynamometer. Otherwise, serious transmission damage will result.
Page 277: Preparing To Drive
The U.S. Environmental Protection Agency (EPA) and states using two- wheel dynamometers in their emission testing programs have EXEMPTED Subaru AWD vehicles from the portion of the testing pro- gram that involves a two-wheel dynamometer. There are some states that use four-wheel dynamometers in their testing programs.
Page 278: Starting The Engine
Starting the engine CAUTION Do not operate the starter motor continuously for more than ten seconds. If the engine fails to start after operating the starter for five to ten seconds, wait for ten seconds or more before trying again. J Starting the engine for a manual transmission vehicle 1.
Page 279: Starting The Engine During Cold Weather Below -4 °F (-20 °C)
1. Apply the parking brake. 2. Turn off unnecessary lights and accessories. 3. Shift the selector lever to the “P” or “N” position (preferably “P” posi- tion). The starter will only operate when the select lever is at the “P” or “N”...
Page 280: Stopping The Engine
Stopping the engine WARNING Do not stop the engine when the vehicle is moving. This will cause loss of power to the power steering and the brake booster, making steering and braking more difficult. It could also result in accidental activation of the “LOCK” position on the ignition switch, causing the steering wheel to lock.
Page 281: Shifting Speeds
The shift pattern is shown on the shift lever knob. When shifting from 5th gear to reverse gear, first return the shift lever to the neutral position then shift into reverse gear. To change gears, fully depress the clutch pedal, move the shift lever, and gradually let up on the clutch pedal.
Page 282 n Maximum allowable speeds WARNING When shifting down a gear, ensure that the vehicle is not travel- ling at a speed exceeding the Maximum Allowable Speed for the gear which is about to be selected. Failure to observe this pre- caution can lead to engine over-revving and this in turn can result in engine damage.
Page 283: Automatic Transmission
When it is necessary to reduce vehicle speed due to slow traffic, turn- ing corners, or driving up steep hills, downshift to a lower gear before the engine starts to labor. On steep downgrades, downshift the transmission to 4th, 3rd or 2nd gear as necessary;...
Page 284: Selector Lever For Automatic Transmission
NOTE Immediately after a disconnected battery is reconnected or ATF (au- tomatic transmission fluid) is replaced, you may feel that the auto- matic transmission operation is somewhat unusual. This results from erasure or invalidation of data the on-board com- puter has collected and stored in memory to allow the transmission to shift at the most appropriate times for the current condition of your vehicle.
Page 285 To shift the selector lever from the “P” to the any other position, you have to depress the brake pedal fully when the ignition switch is in the “ON” position. This prevents the vehicle from lurching when it is started. If the shift lever does not move from the “P”...
Page 286 Starting and operating taking place when the accelerator is released. This minimizes the chance of subsequent downshifting to a lower gear when accelerat- ing again. This prevents repeated upshifting and downshifting result- ing in a smoother operation of the vehicle. NOTE The transmission may downshift to 2nd or 1st gear, depending on the way the accelerator pedal is pressed to accelerate the vehicle...
Page 287 B 2 (Second) This position is for using engine braking when going down a hill or for climbing a steep grade. In this position, the transmission holds in the 2nd gear. Use this position when starting off from a standstill on slippery road surfaces such as mud or snow.
Page 288: Shift Lock Release
Vehicle Brighton, L Brighton L type type Position 35 (56) 64 (103) 100 (161) NOTE In order to prevent over-revving during deceleration of the vehicle, the transmission will remain in the current gear if the speed of the vehicle is in excess of the Maximum Allowable Speed for the gear to which the selector lever has been moved.
Page 289: Rear Viscous Limited Slip Differential (Lsd) (If Equipped)
“P” to the “N” position. 6. Remove the screwdriver from the hole. Depress the brake pedal and start the engine. Take your vehicle to the nearest SUBARU dealer immediately to have the system repaired. Rear viscous limited slip differential (LSD)
Page 290: Power Steering
Power steering CAUTION Do not hold the steering wheel at the fully locked position left or right for more than five seconds. This may damage the power steering pump. The power steering system operates only when the engine is running. If you lose power steering assist because the engine stops or the system fails to function, you can steer but it will take much more effort.
Page 291: Brake System
B Use of engine braking Remember to make use of engine braking in addition to foot braking. When descending a grade, if only the foot brake is used, the brakes may start working improperly because of brake fluid overheating, caused by overheated brake pads. To help prevent this, shift into a lower gear to get stronger engine braking.
Page 292: Disc Brake Pad Wear Warning Indicators
The disc brake pad wear warning indicators on the disc brakes give a warning noise when the brake pads are worn. If a squeaking or scraping noise is heard from the disc brakes while braking, immediately have your vehicle checked by your SUBARU deal- ABS (Anti-lock Brake System) WARNING Always use the utmost care in driving –...
Page 293 leave ample distance from other vehicles. D When you feel the ABS system operating, you should maintain constant brake pedal pressure. Do not pump the brake pedal since doing so may defeat the operation of the ABS system. The ABS system prevents the lock-up of wheels which may occur during sudden braking or braking on slippery road surfaces.
Page 294 8 mph (12 km/h). D The warning light comes on during driving. If these occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer. NOTE If the warning light behavior is as described below, the ABS sys- tem may be considered normal.
Page 295: Vdc (Vehicle Dynamics Control) System (If Equipped)
D Whenever suspension components, steering components, or an axle are removed from a vehicle equipped with VDC, have an authorized SUBARU dealer perform an inspection of that system. D The following precautions should be observed in order to ensure that the VDC system is operating properly: –...
Page 296 In the event of wheelspin and/or skidding on a slippery road surface and/or during cornering and/or an evasive maneuver, the VDC system adjusts the engine’s output and the wheels’ respective braking forces to help maintain traction and directional control. D Traction Control Function The traction control function is designed to prevent spinning of the driving wheels on slippery road surfaces, thereby helping to maintain traction and directional control.
Page 297 D It is always important to reduce speed when approaching a cor- ner, even if the vehicle is equipped with VDC. D All four wheels should be fitted with tires of the same size, type, and brand; furthermore, the amount of wear should be the same for all four tires.
Page 298 VDC system is operating normally. The following situations could indicate a malfunction of the VDC sys- tem; if any should occur, have an authorized SUBARU dealer carry out an inspection of the system at the first available opportunity.
Page 299 SUBARU dealer carry out an inspection of those systems at the first available opportunity.
Page 300: Vdc Off Switch
Starting and operating J VDC OFF switch HB7022AA Note: Even when the lighting switch is turned to the “p” or “a” posi- tion, the “OFF” portion of the symbol stamped on the switch will not illu- minate in the dark. Only “VDC” portion will illuminate. Pressing the VDC OFF switch to deactivate the VDC system can facilitate the following operations: D a standing start on a steeply sloping road with a snowy, gravel-cov-...
Page 301: Parking Your Vehicle
the VDC system except under above-mentioned situations. NOTE D When the VDC switch has been pressed to deactivate the VDC system, the VDC system automatically reactivates itself the next time the ignition key is turned to the OFF position and the engine is restarted.
Page 302 Starting and operating To set the parking brake, press the brake pedal firmly and hold it down while fully pulling up the parking brake lever. HB4001BA To release the parking brake, pull the lever up slightly, press the release button, then lower the lever while keeping the button pressed. When the parking brake is set while the engine is running, the parking brake warning light comes on.
Page 303: Cruise Control (If Equipped)
When parking on a hill, always turn the steering wheel. When the vehicle is headed up the hill, the front wheels should be turned away from the curb. When facing downhill, the front wheels should be turned into the curb. Cruise control (if equipped) WARNING Do not use the cruise control under any of the following condi-...
Page 304 B To set cruise control 1. Push the “CRUISE” main switch. The indicator light on the switch will come on. 2. Depress the accelerator pedal until the vehicle reaches the de- sired speed. 3. Push the control lever downward in the “SET, COAST” direction and release it.
Page 305 B To turn off the cruise control There are two ways to turn off the cruise control: D Push the main switch again. D Turn the ignition switch to the “ACC” position (but only when the vehicle is completely stopped). B To change the cruising speed n To increase the speed (by control lever) Push the control lever upward in the “ACCEL, RESUME”...
Page 306 Starting and operating When the difference between the actual vehicle speed and the set speed is less than 4 mph (6.8 km/h), the set speed can be lowered 1 mph (1.6 km/h) each time by pressing the control lever downward in the “SET, COAST”...
Page 307 Driving tips New vehicle break-in driving – the first 1,000 miles (1,600 km) Fuel economy hints ............Engine exhaust gas (Carbon monoxide) Catalytic converter .
Page 308: New Vehicle Break-In Driving - The First 1,000 Miles (1,600 Km)
New vehicle break-in driving – the first 1,000 miles (1,600 km) The performance and long life of your vehicle are dependent on how you handle and care for your vehicle while it is new. Follow these instructions during the first 1,000 miles (1,600 km): D Do not race the engine.
Page 309: Driving Tips
Fuel economy hints The following suggestions will help to save your fuel. D Select the proper gear position for the speed and road conditions. D Avoid sudden acceleration or deceleration. Always accelerate gently until you reach the desired speed. Then try to maintain that speed for as long as possible.
Page 310: Catalytic Converter
D If at any time you suspect that exhaust fumes are entering the vehicle, have the problem checked and corrected as soon as pos- sible. If you must drive under these conditions, drive only with all windows fully open. D Keep the trunk lid or rear gate closed while driving to prevent exhaust gas from entering the vehicle.
Page 311: Periodic Inspections
D Keep your engine tuned-up. If you feel the engine running rough (mis- firing, backfiring or incomplete combustion), have your vehicle checked and repaired by an authorized SUBARU dealer. D Do not apply undercoating or rust prevention treatment to the heat shield of catalytic converter and the exhaust system.
Page 312: Driving Tips For Awd Vehicles
By shifting power between the front and rear wheels, SUBARU AWD can also pro- vide added traction during acceleration, and added engine braking force during deceleration.
Page 313: Off Road Driving
ing. Therefore, when driving down a slope or turning corners, be sure to reduce your speed and maintain an ample distance from other vehicles. D When replacing a tire, make sure you use only the same size, circum- ference, construction, brand, and load range as the original tires listed on the tire placard.
Page 314 Because of the AWD feature and higher ground clearance, your Subaru can be driven on ordinary roads or off-road. But please keep in mind that an AWD Subaru is a passenger car and is neither a con- ventional off-road vehicle nor an all-terrain vehicle. If you do take your...
Page 315 Driving tips bump could jerk the wheel and injure your hands. Instead drive with your fingers and thumbs on the outside of the rim. D If driving through water, such as when crossing shallow streams, first check the depth of the water and the bottom of the stream bed for firmness and ensure that the bed of the stream is flat.
Page 316: Winter Driving
“Warranty and Maintenance Booklet”. Remember that damage done to your Subaru while operating it off- road and not using common sense precautions such as those listed above is not eligible for warranty coverage.
Page 317 Keep the door locks from freezing by squirting them with deicer or glycerin. Forcing a frozen door open may damage or separate the rubber weather strips around the door. If the door is frozen, use hot water to melt the ice, and afterwards thoroughly wipe the water away. Use a windshield washer fluid that contains an antifreeze solution.
Page 318 When an antifreeze additive is used, its effect lasts longer if the tank is refilled whenever the fuel level reaches half empty. If your SUBARU is not going to be used for an extended period, it is best to have the fuel tank filled to capacity.
Page 319: Corrosion Protection
Driving tips n Wiper operation when snowing Before driving in cold weather, make sure the wiper blades are not frozen to the windshield or rear window. If the wiper blades are frozen to the windshield or rear window, use the defroster with the airflow control button/dial in the “...
Page 320: Snow Tires
J Snow tires B All models except Outback WARNING D When replacing original tires with winter (snow) tires, make sure you use only the same size, construction and load range as the original tires listed on the tire placard. Using other sizes and construction may affect speedometer/odometer calibration and clearance between the body and tires.
Page 321 B Outback models only WARNING D When replacing original tires with winter (snow) tires, make sure you use only the same size and construction as recom- mended. Using other sizes or construction may affect speedome- ter/odometer calibration and clearance between the body and tires.
Page 322: Tire Chains
vehicle and may cause rubbing on sharp turns. Listed below is the winter tire size that we recommend. Recommended winter (snow) tire size P215/60R16 Studless J Tire chains CAUTION Tire chains cannot be used on tires listed below because of lack of clearance between the tires and vehicle body.
Page 323: Loading Your Vehicle
Refer to the “Automatic transmission” section in chapter 7 for information on holding the transmission in 2nd position. Loading your vehicle WARNING D Never allow passengers to ride on the folded rear seatback, in the trunk or in the cargo area. Doing so may result in serious in- jury.
Page 324: Vehicle Capacity Weight
NOTE For better fuel economy, do not carry unneeded cargo. J Vehicle capacity weight HB8015BA HB0382 The load capacity of your vehicle is determined by weight, not by avail- able cargo space. The maximum load you can carry in your vehicle is shown as the Vehicle Capacity Weight on the tire information label at- tached to the driver’s side door jamb.
Page 325: Gvwr And Gawr (Gross Vehicle Weight Rating And Gross Axle Weight Rating)
Driving tips J GVWR and GAWR (Gross Vehicle Weight Rating and Gross Axle Weight Rating) HBF019BB The certification label attached to the driver’s side door shows GVWR (Gross Vehicle Weight Rating) and GAWR (Gross Axle Weight Rating). The GVW (Gross Vehicle Weight) must never exceed the GVWR. GVW is the combined total of weight of the vehicle, fuel, driver, all passengers, luggage, any optional equipment and trailer tongue load.
Page 326: Roof Rail And Crossbar (If Equipped)
J Roof rail and crossbar (if equipped) CAUTION D For cargo carrying purposes, the roof rail must be used to- gether with a roof crossbar kit and the appropriate carrying at- tachment. The roof rail must never be used alone to carry cargo. Otherwise, damage to the roof or paint or a dangerous road haz- ard due to loss of cargo could result.
Page 327 Vehicle Weight Rating (GVWR) and front and rear Gross Axle Weight Rat- ing (GAWR). See the “Loading your vehicle” section in this chapter for information on loading cargo into or onto your vehicle. The maximum load limit of the cargo, crossbars and carrying attachment must not ex- ceed 100 lb.
Page 328 n To remove the crossbar 1. Loosen and remove the T–30 torxR head screw from the top of each crossbar end support. 2. Rotate the lower clamp on the bottom of each end support down- ward approximately 90°. 3. Carefully raise the crossbar from roof rails. n To install the crossbar Front crossbar: Front crossbar has 100 LBS.
Page 329 NOTE It may be necessary to squeeze the lower clamp and the end sup- port together to compress the pads and gain a better alignment of the pieces while trying to start the screw. Use care not to crossthread the screw in the insert. 5.
Page 330: Trailer Hitch (If Equipped)
Trailer hitch (if equipped) WARNING D Never exceed the maximum weight specified for the trailer hitch. Exceeding the maximum weight could cause an accident resulting in serious personal injuries. Permissible trailer weight changes depending on the situation. Refer to the next section “Trailer towing”...
Page 331 B Connecting a trailer 1. Remove the receiver cover from the hitch receiver tube. Then in- sert the ball mount into the hitch receiver tube. 2. Insert the hitch pin into the hole on the hitch receiver tube so that the pin passes through the ball mount.
Page 332 4. Pull the ball mount to make sure it does not come off the hitch re- ceiver. HB8020AA 5. Use only a hitch ball that is appropriate for the ball mount and your trailer. The hitch ball must be securely installed on the ball mount. 6.
Page 333 Driving tips 8. Connect the hitch wire harness’s black four–pin wire connector to the towing trailer’s wire harness HB8021BB 9. Confirm proper function of the hitch wire harness by individually activating the brake, right turn signal, left turn signal, stop, and park- ing lights on the trailer.
Page 334: Trailer Towing
If you do decide to tow a trailer, your safety and satisfaction depend upon proper use of correct equipment and cautious operation of your ve- hicle. Seek the advice of your SUBARU dealer to assist you in purchas- ing a hitch and other necessary towing equipment appropriate for your vehicle.
Page 335 CAUTION D Adequate size trailer brakes are required when the trailer and its cargo exceed 1,000 lbs (453 kg) total weight. D Before towing a trailer, check the trailer total weight, GVW, GAWs and tongue load. Make sure the load and its distribution in your vehicle and trailer are acceptable.
Page 336 n Gross Vehicle Weight (GVW) and Gross Vehicle Weight Rating (GVWR) The Gross Vehicle Weight (GVW) must never exceed the Gross Vehicle Weight Rating (GVWR). Gross Vehicle Weight (GVW) is the combined total of the weight of the vehicle, driver, passengers, luggage, trailer hitch, trailer tongue load and any other optional equipment installed on your vehicle.
Page 337 Gross Axle Weight To check both GVWR and GAWR and to confirm that the total weight and weight distribution are within safe driving limits, you should have your vehicle and trailer weighed at a commercial weighing station. Be sure that all cargo is firmly secured to prevent a change in weight distribution while driving.
Page 338 Tongue load OM-H2785 OM-H2786 The tongue load can be adjusted by proper distribution of the load in the trailer. Never load the trailer with more weight in the back than in the front; approximately 60 percent of the trailer load should be in the front and approximately 40 percent in the rear.
Page 339 Choose a proper hitch for your vehicle and trailer. B OUTBACK wagon The use of a genuine SUBARU trailer hitch is recommended. A genu- ine SUBARU hitch is available from your SUBARU dealer. If use of a non-genuine hitch is unavoidable, be sure the hitch is suited to your vehicle and trailer.
Page 340 B All vehicles except OUTBACK wagon SUBARU does not offer accessory trailer hitches. Consult with a pro- fessional hitch supplier to assist you in choosing an appropriate hitch for your vehicle. Be sure to follow all of the hitch manufacturer’s instructions for installation and use.
Page 341 In case the trailer hitch connector or hitch ball should break or become disconnected, the trailer could get loose and create a traffic safety hazard. For safety, always connect the towing vehicle and trailer with trailer safety chains. Pass the chains crossing each other under the trailer tongue to prevent the trailer from dropping onto the ground in case the trailer tongue should disconnect from the hitch ball.
Page 342 To ensure the trailer lights are connected properly, please consult your SUBARU dealer. Check for proper operation of the turn signals, the brake lights and parking lights each time you hitch up.
Page 343 B Trailer towing tips CAUTION D Never exceed 45 mph (72 km/h) when towing a trailer in hilly country on hot days. D When towing a trailer, steering, stability, stopping distance and braking performance will be different from normal operation. For safety’s sake, you should employ extra caution when towing a trailer and you should never speed.
Page 344 n Driving with a trailer D You should allow for considerably more stopping distance when towing a trailer. Avoid sudden braking because it may result in skid- ding or jackknifing and loss of control. D Avoid abrupt starts and sudden accelerations. If your vehicle has a manual transmission, always start out in first gear and release the clutch at moderate engine revolution.
Page 345 Driving tips nearest SUBARU dealer. n Driving on grades D Before going down a steep hill, slow down and shift into lower gear (if necessary, use 1st gear) in order to utilize the engine braking effect and prevent overheating of your vehicle’s brakes. Do not make sud- den downshifts.
Page 346 5. Shift into 1st or reverse gear (manual transmission) or “P” (auto- matic transmission) and shut off the engine. 8-40...
Page 347 In case of emergency If you park your vehicle in an emergency Temporary spare tire ........... . Flat tires .
Page 348: If You Park Your Vehicle In An Emergency
If you park your vehicle in an emergency HB8002BA The hazard warning flasher should be used in day or night to warn other drivers when you have to park your vehicle under emergency conditions. Avoid stopping on the road. It is best to safely pull off the road if a prob- lem occurs.
Page 349: In Case Of Emergency
Temporary spare tire WARNING Never tow a trailer when the temporary spare tire is used. The temporary spare tire is not designed to sustain the towing load. Use of the temporary spare tire when towing can result in failure of the spare tire and/or less stability of the vehicle and may lead to an accident.
Page 350: Flat Tires
Indicator location mark NOTE [Automatic transmission vehicle not equipped with VDC (Vehicle Dy- namics Control)] Before driving your vehicle with the temporary spare tire, put a spare fuse inside the FWD connector located in the engine compartment and confirm that the Front-wheel drive warning light comes on.
Page 351 D Do not use oil or grease on the wheel studs or nuts when the spare tire is installed. This could cause the nuts to become loose and lead to an accident. D Never place a tire or tire changing tools in the passenger compartment after changing wheels.
Page 352 5. Take out the spare tire, jack, and wheel nut wrench. Jack Spare tire Temporary spare tire The spare tire is stored under the floor of the trunk or cargo area. To remove the spare tire, proceed as follows: Sedan: Remove the floor cover from the trunk. Remove the storage tray. Turn the attaching bolt counterclockwise, then take the spare tire out.
Page 353 In case of emergency side of the lid on the rear edge of the roof to keep the lid open. Remove the storage tray. Turn the attaching bolt counterclockwise, then take spare tire out. If the spare tire provided in your vehicle is a temporary spare tire, care- fully read the section “Temporary spare tire”...
Page 354 6. (If your vehicle has wheel covers) Insert the wheel nut wrench into the notch provided in the wheel cover, and pry it off. HB9032BA OM-H0376 7. Loosen the wheel nuts using the wheel nut wrench but do not remove the nuts.
Page 355 In case of emergency 9. Insert the jack handle into the jackscrew, and turn the handle until the tire clears the ground. Do not raise the vehicle higher than necessary. OM-H2263 10. Remove the wheel nuts and the flat tire. 11.
Page 356 14. Use the wheel nut wrench to securely tighten the wheel nuts to the specified torque, following the tightening order in the illustration. OM-H0377 The torque for tightening the nuts is 58 to 72 ft-lb (78 to 98 N-m, 8 to 10 kg-m).
Page 357: Jump Starting
Jump starting WARNING D Battery fluid is SULFURIC ACID. Do not let it come in contact with the eyes, skin, clothing or the vehicle. If battery fluid gets on you, thoroughly flush the exposed area with water immediately. Get medical help if the fluid has entered your eyes.
Page 358 B How to jump start 1. Make sure the booster battery is 12 volts and the negative terminal is grounded. 2. If the booster battery is in another vehicle, do not let the two ve- hicles touch. 3. Turn off all unnecessary lights and accessories. 4.
Page 359 Connect one jumper cable to the positive (+) terminal on the discharged battery. Connect the other end of the jumper cable to the positive (+) terminal of the booster battery. Connect one end of the other cable to the negative (–) terminal of the booster battery.
Page 360: Engine Overheating
Engine overheating WARNING Never attempt to remove the radiator cap until the engine has been shut off and has fully cooled down. When the engine is hot, the coolant is under pressure. Removing the cap while the engine is still hot could release a spray of boiling hot coolant, which could burn you very seriously.
Page 361: Towing
This will cause the vehicle to spin away due to the operation or deterioration of the center differential. If towing is necessary, it is best done by your SUBARU dealer or a com- mercial towing service. Observe the following procedures for safety.
Page 362 9-16 HB9004BB Towing and tie-down hook HB8012BB HB9005BB HB8013BB...
Page 363 In case of emergency HB9010BB The towing hooks should be used only in an emergency (e.g., to free a stuck vehicle from mud, sand or snow). The front towing hook is located on the inside of the towing hook cov- er below the right-hand headlight.
Page 364 HB9014BB 2. Insert your fingers under the raised portion B. Then, pull it toward you so that the towing hook cover may swing open. Remove the cov- For OUTBACK models: HB9017BB HB9018BA 1. Pull the towing hook cover toward you while pushing up the portion A.
Page 365 2. Pull the portion B toward you with your left hand. Simultaneously pull the portion C toward you while pushing the portion C with your right hand. 3. Push the portion D. Pull out the towing hook cover to remove it. HB9019BB HB9021BB HB9023BB...
Page 366 n Towing hook cover installation procedure For except OUTBACK models: HB9015BA HB9016BA 1. Insert the towing hook cover into the clearance between the fog light (or bumper trim cover) and the bumper body. HB9013CB 2. Push the towing hook cover in accordance with the pushing order given in the illustration.
Page 367 In case of emergency For OUTBACK models: HB9025BA 1. Insert the guide E into the hole F. HB9026BB HB9027BB 2. Fit the flange G in the slit H from the left end. While holding the towing hook cover at the portion G, push at the portion I. –...
Page 368 HB9028BB HB9029BB 3. Push at the portion J. Check that the tab of the portion K is fitted in the bumper as shown in the illustration. HB9030BB 4. Push the portion L. 9-22...
Page 369 B Using a flat-bed truck This is the best way to transport your vehicle. Use the following proce- dures to ensure safe transportation. 1. Shift the selector lever into the “P” position for automatic transmis- sion vehicles or “1st” for manual transmission vehicles. 2.
Page 370 CAUTION D If transmission failure occurs, transport your vehicle on a flat- bed truck. D Do not run the engine while being towed in this method. Trans- mission damage could result if the vehicle is towed with the engine running. D For vehicles with automatic transmission, the traveling speed must be limited to less than 20 mph (30 km/h) and the traveling distance to less than 31 miles (50 km).
Page 371: Moonroof - If The Moonroof Cannot Be Closed
3. Insert the wrench in the end of the motor shaft. D To lower the moonroof, turn the wrench clockwise. D To close the moonroof, turn the wrench counterclockwise. Have your vehicle checked by an authorized SUBARU dealer. HB9006BA HB9008BA...
Page 372: Maintenance Tools
3. Insert the wrench in the end of the motor shaft. To close the moonroof, turn the wrench clockwise. Have your vehicle checked or repaired by an authorized SUBARU dealer. Maintenance tools...
Page 373: J Jack And Jack Handle
Screwdriver Wheel nut wrench Hex-headed wrench (for vehicles with moonroof) J Jack and jack handle Jack Spare tire The jack is stored on the left side of the trunk or cargo area. To take out the jack, turn the jackscrew counterclockwise to loosen it, then remove the jack.
Page 374 Appearance care Exterior care ..............Washing .
Page 375: Exterior Care
Exterior care J Washing CAUTION D When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes.
Page 376: Appearance Care
B Washing the underbody Chemicals, salts and gravel used for deicing road surfaces are ex- tremely corrosive, accelerating the corrosion of underbody compo- nents, such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders, and suspension. Thoroughly flush the underbody and inside of the fenders with luke- warm or cold water at frequent intervals to reduce the harmful effects of such agents.
Page 377: Cleaning Aluminum Wheels
When in doubt, it is always best to contact your SUBARU dealer or an auto paint specialist. J Cleaning aluminum wheels D Promptly wipe the aluminum wheels clean of any kind of grime or agent.
Page 378 Corrosion protection Your SUBARU has been designed and built to resist corrosion. Special materials and protective finishes have been used on most parts of the vehicle to help maintain fine appearance, strength, and reliable opera- tion.
Page 379: Cleaning The Interior
If any of them are found to be rusted, they should be given an appropriate rust prevention treatment or should be replaced. Contact your SUBARU dealer to perform this kind of maintenance and treatment if you need assistance.
Page 380 A mild detergent suitable for cleaning woolen fabrics may be used to remove difficult dirt spots, rubbing with a soft, dry cloth afterwards to restore the luster. If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading or shrinkage.
Page 381 Maintenance and service Maintenance schedule Maintenance precautions Engine hood ..............Engine compartment overview Engine oil .
Page 382 Battery ............... . Fuses .
Page 383: Maintenance And Service
Maintenance precautions When maintenance and service are required, it is recommended that all work be done by an authorized SUBARU dealer. If you perform maintenance and service by yourself, you should familiar- ize yourself with the information provided in this section on general main- tenance and service for your SUBARU.
Page 384 This will cause a fire. D Because the fuel system is under pressure, replacement of the fuel filter should be performed only by your SUBARU dealer. D Wear adequate eye protection to guard against getting oil or fluids in your eyes. If something does get in your eyes, thorough- ly wash them out with clean water.
Page 385: Engine Hood
Maintenance and service J When you do checking or servicing in the engine compartment while the engine is running A running engine can be dangerous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other moving engine parts.
Page 386 HBB003BA To open the hood: 1. Pull the hood release knob under the instrument panel. 2. Release the secondary hood release located under the front grille by moving the lever toward the left. Lift up the hood, release the hood prop from its retainer and put the end of the hood prop into the slot in the hood.
Page 387: Engine Compartment Overview
Engine compartment overview B 2.5 liter models Manual transmission oil level gauge (MT) (page 11-23) or Differential gear oil level gauge (AT) (page 11-26) Air cleaner element (page 11-18) Clutch fluid reservoir (page 11-32) Automatic transmission fluid level gauge (page 11-24) Brake fluid reservoir (page 11-30) Fuel filter...
Page 388 B 3.0 liter models Air cleaner element (page 11-18) Differential gear oil level gauge (AT) (page 11-26) Automatic transmission fluid level gauge (page 11-24) Brake fluid reservoir (page 11-30) Fuel filter Windshield washer tank (page 11-47) 11-8 Fuse box (page 11-52) Battery (page 11-51) Engine oil filler cap (page 11-9)
Page 389: Engine Oil
Maintenance and service Engine oil B Checking the oil level Check the engine oil level at each fuel stop. HBB004BA HBB061BD 1. Park the vehicle on a level surface and stop the engine. 2. Pull out the dipstick, wipe it clean, and insert it again. 3.
Page 390 B Changing the oil and oil filter Change the oil and oil filter according to the maintenance schedule in the “Warranty and Maintenance Booklet”. The engine oil and oil filter must be changed more frequently than listed in the maintenance schedule when driving on dusty roads, when short trips are frequently made, or when driving in extremely cold whether.
Page 391 6. Remove three clips at the front of the cover under the oil filter. 7. Slide the cover toward the vehicle front to remove it. 8. Remove the oil filter with an oil filter wrench. 9. Before installing a new oil filter, apply a thin coat of engine oil to the seal.
Page 392 12. Reinstall the cover under the oil filter. 13. Pour the specified amount of engine oil through the filler neck. Oil capacity: 2.5 liter models: 4.2 US qt (4.0 liters, 3.5 Imp qt) 3.0 liter models: 6.1 US qt (5.8 liters, 5.1 Imp qt) 14.
Page 393 When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity as those rec- ommended by SUBARU. Engine oil viscosity (thickness) affects fuel economy. Oils of lower vis- cosity provide better fuel economy. However, in hot weather, oil of higher viscosity is required to properly lubricate the engine.
Page 394: Cooling System
–33°F (–36°C). For adding, use genuine SUBARU coolant or an equivalent: a mixture of 50% soft water and 50% ethylene-glycol basis coolant. Use of improp- er coolants may result in corrosion in the cooling system. It is im- portant to maintain protection against freezing and corrosion, even if freezing temperatures are not expected.
Page 395: Engine Coolant
Maintenance and service J Engine coolant B Checking the coolant level Check the coolant level at each fuel stop. HBB004FB 1. Check the coolant level on the outside of the reservoir while the engine is cool. 2. If the level is close to or lower than the “LOW” level mark, add coolant up to the “FULL”...
Page 396 B Changing the coolant WARNING Never attempt to remove the radiator cap until the engine has been shut off and has cooled down completely. Since the coolant is under pressure, you may suffer serious burns from a spray of boiling hot coolant when the cap is removed. Change the engine coolant using the following procedures according to the maintenance schedule in the “Warranty and Maintenance Book- let”.
Page 397 4. Slowly pour the coolant and fill to the radiator filler neck and to the reserve tank’s “FULL” level mark. Do not pour the coolant too quickly, as this may lead to insufficient air bleeding and trapped air in the sys- tem.
Page 398: Air Cleaner Element
B Replacing the air cleaner element Replace the air cleaner element according to the maintenance sched- ule in the “Warranty and Maintenance Booklet”. Under extremely dusty conditions, replace it more frequently. It is recommended that you always use genuine SUBARU parts. 11-18...
Page 399 Maintenance and service n 2.5 liter models HBB063BB HBB064BB 1. Remove the bolt securing the rear air cleaner element case. 2. Unsnap the three clamps holding the rear air cleaner element case. 3. Separate the rear air cleaner element case from the front air clean- er element case and remove the air cleaner element.
Page 400: Spark Plugs
2. Open the air cleaner case cover and remove the air cleaner ele- ment. 3. Clean the inside of the air cleaner cover and case with a damp cloth and install a new air cleaner element. To install the air cleaner case cover, insert the two projections on the air cleaner case cover into the slits on the air cleaner case and then snap the two clamps on the air cleaner case cover.
Page 401 It may be difficult to replace the spark plugs. It is recommended that you have the spark plugs replaced by your SUBARU dealer. The spark plugs should be replaced according to the maintenance schedule in the “Warranty and Maintenance Booklet”.
Page 402: Drive Belts
Drive belts The alternator, power steering pump, and air conditioner compressor de- pend on drive belts. Satisfactory performance requires that belt tension be correct. B 2.5 liter models To check belt tension, place a straightedge (ruler) across two adja- cent pulleys and apply a force of 22 lb (98 N, 10 kg) midway between the pulleys by using a spring scale.
Page 403: Manual Transmission Oil
“Warranty and Maintenance Booklet”. Consult your SUBARU dealer for replacement. If a belt is loose, cracked, or worn, contact your SUBARU dealer. Manual transmission oil B Checking the oil level Check the oil level monthly. 1. Park the vehicle on a level surface and stop the engine.
Page 404: Automatic Transmission Fluid
SAE viscosity No. and Applicable Temperature Automatic transmission fluid B Checking the fluid level The automatic transmission fluid expands largely as its temperature rises; the fluid level differs according to fluid temperature. Therefore, there are two different scales for checking the level of hot fluid and cold fluid on the dipstick.
Page 405: Recommended Fluid
Maintenance and service Upper level HOT range Lower level Upper level COLD range Lower level HBA008BB HBB004CB 4. Pull out the dipstick and check the fluid level on the gauge. If it is below the lower level on the “HOT” range, add the recommended au- tomatic transmission fluid up to the upper level.
Page 406: Front Differential Gear Oil (At Vehicles)
Front differential gear oil (AT vehicles) B Checking the oil level Check the differential oil level monthly. Upper level Lower level HBA010BB HBB004EB 1. Park the vehicle on a level surface and stop the engine. 2. Pull out the dipstick, wipe it clean, and insert it again. 3.
Page 407: Rear Differential Gear Oil
If the vehicle requires frequent refilling, there may be an oil leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. Your vehicle may be equipped with a rear differential protector. The differential protector provides protection to the rear differential assem- bly during off-road use.
Page 408 HBB065BB HBB066BB Others Filler plug Oil level Filler hole Drain hole Drain plug HB0077 HB0078 Remove the plug from the filler hole and check the oil level. The oil level should be kept even with the bottom of the filler hole. If the oil level is below the bottom edge of the hole, add oil through the filler hole to raise the level.
Page 409: Power Steering Fluid
SAE viscosity No. and Applicable Temperature Power steering fluid B Checking the fluid level WARNING Be careful not to burn yourself because the fluid may be hot. CAUTION D When power steering fluid is being added, use only clean fluid, and be careful not to allow any dirt into the tank.
Page 410: Brake Fluid
“MIN” and “MAX” line. If the fluid level is extreme low, it may indicate possible leakage. Con- sult your SUBARU dealer for inspection. B Recommended fluid “Dexron III” Type Automatic Transmission Fluid...
Page 411 D If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. CAUTION D Never use different brands of brake fluid together. D When adding brake fluid, be careful not to allow any dirt into the reservoir.
Page 412: Clutch Fluid (Mt Vehicles)
D If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. D Never use different brands of clutch fluid together. D When clutch fluid is added, be careful not to allow any dirt into the tank.
Page 413: Brake Booster
Brake booster If the brake booster does not operate as described below, have it checked by your SUBARU dealer. 1. With the engine off, depress the brake pedal several times, applying the same pedal force each time. The distance the pedal travels should not vary.
Page 414: Brake Pedal
Lightly press the brake pedal down with one finger to check the free play with a force of less than 2 lb (10 N, 1 kg). If the free play is not within proper specification, contact your SUBARU dealer. B Checking the brake pedal reserve distance More than 2.56 in...
Page 415: Clutch Pedal (Manual Transmission Vehicles)
When the measurement is smaller than the specification, or when the pedal does not operate smoothly, contact with your SUBARU dealer. Clutch pedal (Manual transmission vehicles) Check the clutch pedal free play and reserve distance according to the maintenance schedule in the “Warranty and Maintenance Booklet”.
Page 416: Replacement Of Brake Pad And Lining
If you hear this scraping noise each time you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as pos- sible. B Breaking-in of new brake pads and linings When replacing the brake pad or lining, use only genuine SUBARU parts.
Page 417: Parking Brake Stroke
(about 44 lb, 196 N, 20 kg). If the parking brake lever stroke is not within the specified range, have the brake system checked and adjusted at your SUBARU dealer. Maintenance and service –...
Page 418: Tires And Wheels
Tires and wheels J Types of tires You should be familiar with type of tires present on your vehicle. B All season tires The factory-installed tires on your new vehicle are all season tires. All season tires are designed to provide an adequate measure of trac- tion, handling and braking performance in year-round driving includ- ing snowy and icy road conditions.
Page 419: Tire Inspection
Check on a daily basis that the tires are free from serious damage, nails, and stones. At the same time, check the tires for abnormal wear. Contact your SUBARU dealer immediately if you find any problem. NOTE D When the wheels and tires strike curbs or are subjected to harsh treatment as when the vehicle is driven on a rough surface, they can suffer damage that cannot be seen with the naked eye.
Page 420 Driving even a short distance warms up the tires and increases the tire pressures. Also, the tire pressures are affected by the ambient tempera- ture. It is best to check tire pressure outdoors before driving the vehicle. When a tire becomes warm, the air inside it expands, causing the tire pressure to increase.
Page 421 D Correct tire pressure (tread worn evenly) Roadholding is good, and steering is responsive. Rolling resistance is low, so fuel consumption is also lower. D Abnormally low tire pressure (tread worn at shoulders) Rolling resistance is high, so fuel consumption is also higher. Maintenance and service HGB033AA HSB012AA...
Page 422: Wheel Balance
If you suspect that the wheels are not correctly balanced, have them checked and adjusted by your SUBARU dealer. Also have them adjusted after tire repairs and after tire rotation.
Page 423: Wear Indicators
Loss of correct wheel alignment* causes the tires to wear on one side and reduces the vehicle’s running stability. Contact your SUBARU dealer if you notice abnormal tire wear. * : The suspension system is designed to hold each wheel at a certain alignment (relative to the other wheels and to the road) for optimum straight-line stability and cornering performance.
Page 424: Tire Rotation
J Tire rotation OM-H0230 Tire wear varies from wheel to wheel. To maximize the life of each tire and ensure that the tires wear uniformly, it is best to rotate the tires every 7,500 miles (12,500 km). Rotating the tires involves switching the front and rear tires on the right-hand side of the vehicle and similarly switching the front and rear tires on the left-hand side of the vehicle.
Page 425: Wheel Replacement
All four tires must be the same in terms of manufacturer, brand (tread pattern), construction, and size. You are advised to replace the tires with new ones that are identical to those fitted as standard equipment. For safe vehicle operation, SUBARU recommends replacing all four tires at the same time. WARNING...
Page 426: Wheel Covers
J Wheel covers B Removing the wheel cover Insert the wheel nut wrench into the notch provided, and pry the wheel cover off. B Installing the wheel cover Align the valve with the valve hole in the cover, then fit the cover on the wheel by tapping your hand evenly around the circumference of the cover.
Page 427: Aluminum Wheels (If Equipped)
D Be sure to fit tire chains on uniformly and completely around the tire, otherwise the chains may scratch the wheel. D When wheel nuts, balance weights, or the center cap is replaced, be sure to replace them with genuine SUBARU parts designed for aluminum wheels. Windshield washer fluid...
Page 428: Replacement Of Windshield Wiper Blades
Washer Fluid Concentration 100% Replacement of windshield wiper blades Grease, wax, insects, or other materials on the windshield or the wiper blade results in jerky wiper operation and streaking on the glass. If you cannot remove the streaks after operating the windshield washer or if the wiper operation is jerky, clean the outer surface of the windshield (or rear window) and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner.
Page 429 1. Raise the wiper arm off the windshield. 2. Remove the wiper blade assembly by holding its pivot area and push- ing it in the direction shown by the arrow while depressing the wiper blade stopper. Stopper 3. Grasp the locked end of the blade rubber assembly and pull it firmly until the stoppers on the rubber are free of the metal support.
Page 430 4. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber. Metal spines HS0192 5. Align the claws of the metal support with the grooves in the rubber and slide the blade rubber assembly into the metal support until it locks.
Page 431: Battery
Battery WARNING D Before beginning work on or near any battery, be sure to extin- guish all cigarettes, matches, and lighters. Never expose a bat- tery to an open flame or electric sparks. Batteries give off a gas which is highly flammable and explosive. D For safety, in case an explosion does occur, wear eye protec- tion or shield your eyes when working near any battery.
Page 432: Fuses
It is unnecessary to periodically check the battery fluid level or periodi- cally refill with distilled water. Fuses CAUTION Never replace a fuse with one having a higher rating or with mate- rial other than a fuse because serious damage or a fire could re- sult.
Page 433 5. Inspect the fuse. If it has blown, replace it with a spare fuse of the same rating. 6. If the same fuse blows again, this indicates that its system has a problem. Contact your SUBARU dealer for repairs. – CONTINUED – 11-53...
Page 434: Main Fuse
SUBARU dealer. Installation of accessories Always consult your SUBARU dealer before installing fog lights or any other electrical equipment in your vehicle. Such accessories may cause the electronic system to malfunction if they are incorrectly installed or if they are not suited for the vehicle.
Page 435: Replacing Bulbs
Replacing bulbs Headlight GT and OUTBACK models Low beam High beam Except GT and OUTBACK models Front turn signal Spot light Dome light Door step light Front turn signal light/ parking and front side marker light Front fog light Except OUTBACK OUTBACK Maintenance and service HB5019EB...
Page 436: High Mount Stop Light
Backup light Sedan Station wagon Luggage area light High mount stop light Sedan Station wagon Rear turn signal light Sedan Station wagon Brake/tail light Sedan Station wagon Licence plate light Sedan Station wagon Trunk room light 11-56 HBF013FC Wattage 12V–27W 12V–27W 12V–13W 12V–16W...
Page 437 NOTE If headlight aiming is required, consult your SUBARU dealer for proper adjustment of the headlight aim. B For GT and OUTBACK models Remove the headlight bulb cover, by turning it counterclockwise.
Page 438 n Low beam light bulbs 1. Disconnect the electrical connector for the black cable. 2. Remove the retainer spring. 3. Replace the bulb, then set the retainer spring securely. 4. Reconnect the electrical connector for black cable. 5. Install the headlight bulb cover. n High beam light bulbs 1.
Page 439 6. Remove the electrical connector. J Front fog light (if equipped) It may be difficult to replace the bulbs. Have your SUBARU dealer replace the bulbs if necessary. J Front turn signal light, parking light and side marker...
Page 440 SUBARU dealer. HBB016BA 1. Remove the headlight assembly mounting screws located at the top of and the front of the headlight assembly using a phillips screwdriver or an open-end wrench. 2. Move the headlight assembly forward. HBB020BA HBB039CB 3.
Page 441: Rear Combination Lights
Maintenance and service J Rear combination lights B Sedan HBB034BC HBF014DA HBB035BB 1. Open the trunk lid. 2. Open the rear combination light cover. For covers on the trunk lid: Unlatch the cover by pushing the knob and open the cover. For covers on the trunk wall: Unlatch the cover by moving the knob upward and open the cover.
Page 442 B Station wagon n Brake/tail and rear turn signal light bulbs It may be difficult to replace the bulbs. It is recommended that you have the bulbs replaced by your SUBARU dealer. HBB021BB HBB022BB 1. Remove the light bulb replacement service hole covers at two places by prying the edge of the cover with a regular screwdriver.
Page 443 Maintenance and service 3. Using a Phillips screwdriver, remove the upper and lower screws that secure the side cover of the rear combination light assembly. 4. Remove the bulb socket from the rear combination light assembly by turning it counterclockwise. HBB025BB HBB048BB 5.
Page 444 n Back-up and brake/tail light bulbs 1. Unlatch the rear finisher light cover by moving the knob upward. Open the cover up. 2. Remove the bulb socket from the rear finisher light assembly by turning it counterclockwise. 3. Remove the bulb from the socket by pushing it and turning coun- terclockwise.
Page 445: Spot Light, Dome Light, Luggage Compartment Light
Maintenance and service 2. Remove the cover and lens. 3. Pull the bulb out of the socket. Install a new bulb. 4. Reinstall the lens and cover. 5. Tighten the mounting screws. J Spot light, dome light, luggage compartment light and door step light HBB029BB HBB068BB...
Page 446 HBS037AB 1. Remove the lens by prying the edge of the lens with a regular screw- driver. 2. Pull the bulb out of the socket. Install a new bulb. 3. Reinstall the lens. J Trunk light HBF014FA 1. Remove the cover by squeezing its sides and pulling it. 2.
Page 447 Maintenance and service J High mount stop light B Sedan OM-H2350 1. Remove the high mount stop light cover by prying on the edge with a screwdriver. 2. Pull the bulb out of the socket. Install a new bulb. 3. Reinstall the cover. B Station wagon HBB028BA 1.
Page 448 4. Reinstall the cover. 5. Tighten the mounting screws then reinstall the covers. NOTE Other bulbs may be difficult to replace. Have your SUBARU dealer replace these bulbs if necessary. 11-68...
Page 449 Specifications Specifications ............. . Dimensions .
Page 450: Specifications
Specifications These specifications are subject to change without notice. J Dimensions Legacy sedan Overall length Overall width Overall height Ground clearance Front tread Rear tread Wheelbase Legacy station wagon Overall length Overall width Overall height Ground clearance Front tread Rear tread Wheelbase *: With roof rail OUTBACK sedan...
Page 451: Specifications
Overall height Ground clearance 2.5 liter models 3.0 liter models Front tread Rear tread Wheelbase J Engine 2.5 liter Engine model Engine type Engine displacement Bore Stroke Compression ratio Firing order 3.0 liter Engine model Engine type Engine displacement Bore Stroke Compression ratio Firing order...
Page 452: Capacities
Spark plugs type 3.0 liter Battery type and capacity Alternator Spark plugs type J Capacities Fuel tank Engine oil Transmission oil (MT) Transmission fluid (AT) AT differential gear oil Rear differential gear oil Brighton, L (AT) 0.9 US qt (0.9 liter, 0.8 Imp qt) Others Power steering gear fluid Engine coolant...
Page 453: Wheel Alignment
Temporary spare Wheel size OUTBACK Type Size Temporary spare Pressure Front Trailer towing Rear Trailer towing Temporary spare Wheel size J Wheel alignment Legacy sedan Front Rear Camber Front Rear Legacy station wagon Front Rear Camber Front Rear OUTBACK sedan Camber OUTBACK station wagon Camber...
Page 454: Fuses And Circuits
Fuses and circuits J Fuse panel located behind the coin tray B 2.5 liter models Fuse panel Fuse rating 12-6 Circuit D Heater fan D Heater fan D Power door lock D Keyless entry D Cigarette lighter D Remote controlled rear view mirrors D Tail light D Parking light HBC001BB...
Page 455 Fuse panel Fuse rating Circuit D SRS airbag D Front fog light D ABS solenoid D Radio D Clock D Trailer D Engine ignition system D SRS airbag D Illumination brightness control D Fuel pump D Rear window wiper and washer D Windshield wiper and washer D Brake light D Air conditioner...
Page 456 B 3.0 liter models Fuse panel Fuse rating 12-8 Circuit D Heater fan D Heater fan D Power door lock D Keyless entry D Cigarette lighter D Remote controlled rear view mirrors D Tail light D Parking light D SRS airbag D Front fog light HBC001CB...
Page 457 Fuse panel Fuse rating Circuit D ABS (VDC) solenoid D Radio D Clock D Trailer D Engine ignition system D SRS airbag D Illumination brightness control D Fuel pump D Rear window wiper and washer D Windshield wiper and washer D Brake light D Air conditioner D Backup light...
Page 458 J Fuse panel located in the engine compartment B 2.5 liter models Fuse panel Fuse rating 12-10 Circuit D Radiator cooling fan (Main) D Radiator cooling fan (Sub) D ABS motor D Rear window defogger D Hazard warning flasher D Horn D Meter D SRS airbag system warning light D Automatic transmission control unit...
Page 459 Fuse panel Fuse rating Circuit D Headlight (left side) D Lighting switch D Clock D Interior light Specifications – CONTINUED – 12-11...
Page 460 B 3.0 liter models Fuse panel Fuse rating 12-12 Circuit D Radiator cooling fan (Main) D Radiator cooling fan (Sub) D ABS (VDC) motor D McIntosh audio amp (if equipped) D Rear window defogger D Hazard warning flasher D Horn D Meter D SRS airbag system warning light D Automatic transmission control unit...
Page 461 Fuse panel Fuse rating Circuit D Headlight (left side) D Lighting switch D Clock D Interior light Specifications – CONTINUED – 12-13...
Page 462: Bulb Chart
Bulb chart Headlight GT and OUTBACK Low beam High beam Except GT and OUTBACK Front turn signal Spot light Dome light Door step light Parking and front side marker light Front fog light Except OUTBACK OUTBACK Backup light Sedan Station wagon Luggage area light High mount stop light Sedan...
Page 463: Vehicle Identification
Vehicle identification Emission control label Vehicle identification number Radio noise label (Canada model) Vacuum hose connections label Specifications Tire inflation pressure label Certification and bar cord label Vehicle identification number plate Model number plate – CONTINUED – HBD002BB 12-15...
Page 464: Consumer Information And Reporting Safety Defects
Consumer information and Reporting safety defects Uniform tire quality grading standards Treadwear ..............Traction AA, A, B, C .
Page 465: Uniform Tire Quality Grading Standards
For U.S.A. The following information has been compiled according to Code of Fed- eral Regulations “Title 49, Part 575”. Uniform tire quality grading standards This information indicates the relative performance of passenger car tires in the area of treadwear, traction, and temperature resistance. This is to aid the consumer in making an informed choice in the purchase of tires.
Page 466: Temperature A, B, C
Consumer information and Reporting safety defects phalt and concrete. A tire marked C may have poor traction perfor- mance. WARNING The traction grade assigned to this tire is based on straight- ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.
Page 467 However, NHTSA cannot become involved in individual problems between you, your dealer, or Subaru of America, Inc. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in the Washington D.C.
Page 468: Index
Index ABS (Anti-lock Brake System) ABS warning light ..............Accessory power socket Air cleaner element .
Page 469 Center console ..............Charge warning light .
Page 470 Engine coolant ..............Engine exhaust gas (Carbon monoxide) Engine hood .
Page 471 Headlight ................Headrest adjustment —...
Page 472 Main fuse ................Maintenance precautions Maintenance schedule Maintenance tools...
Page 473 Precautions to observe when handling a compact disc (CD) Preparing to drive ..............Rear combination lights Rear differential gear oil Rear gate (Station wagon)
Page 474 SRS airbag (Supplemental Restraint System airbag) SRS airbag system monitors SRS airbag system servicing SRS airbag system warning light SRS frontal airbag ..............SRS side airbag (if equipped) Starting a flooded engine Starting the engine...
Page 475 Treadwear ................Trunk lid (Sedan) .
Page 476 Wheel replacement ............. . Windows .

This manual is also suitable for:

2002 outback

Subaru 2002 Legacy Owner's Manual

Table of Contents

Seat, Seatbelt and Srs Airbags

Front Seats

Seat Heater (if Equipped)

Rear Seats

Seatbelts

Front Seatbelt Pretensioners

Child Restraint Systems

SRS Airbag (Supplemental Restraint System Airbag)

Keys and Doors

Instruments and Controls

Ignition Switch

Meters and Gauges

Hazard Warning Flasher

Warning and Indicator Lights

Light Control Switch

Clock

Turn Signal Lever

Illumination Brightness Control

Parking Light Switch

Fog Light Switch (if Equipped)

Wiper and Washer

Rear Window Defogger Switch

Windshield Wiper Deicer (if Equipped)

Mirrors

Tilt Steering Wheel

Horn

Climate Control

Audio

Interior Equipment

Starting and Operating

Fuel

State Emission Testing (U.S. Only)

Preparing to Drive

Starting the Engine

Stopping the Engine

Manual Transmission

Automatic Transmission

Rear Viscous Limited Slip Differential (LSD) (if Equipped)

Power Steering

Braking

ABS (Anti-Lock Brake System)

VDC (Vehicle Dynamics Control) System (if Equipped)

Parking Your Vehicle

Cruise Control (if Equipped)

Driving Tips

In Case of Emergency

Appearance Care

Maintenance and Service

Quick Links

Chapters

Related Manuals for Subaru 2002 Legacy

Summary of Contents for Subaru 2002 Legacy