Page 1 2010 GMC Savana Owner Manual In Brief ... 1-1 Instrument Panel ... 1-2 Initial Drive Information ... 1-4 Vehicle Features ... 1-13 Performance and Maintenance Seats and Restraint System ... 2-1 Head Restraints ... 2-2 Front Seats ... 2-2 Rear Seats ...
Page 2 Vehicle Identiﬁcation ... 6-103 Electrical System ... 6-104 Capacities and Speciﬁcations Maintenance Schedule ... 7-1 Maintenance Schedule ... 7-2 Customer Assistance Information ... 8-1 Customer Assistance and Information Reporting Safety Defects ... 6-110 Vehicle Data Recording and Privacy Index ... 1 ...
Page 3 GENERAL MOTORS, GM, the GMC Emblem, GMC, the GMC Truck Emblem, and the name SAVANA are registered trademarks of General Motors Corporation. This manual describes features that may or may not be on your speciﬁc vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual.
Page 4 Safety Warnings and Symbols Warning Messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them. Danger indicates a hazard with a high level of risk which will result in serious injury or death. Warning or Caution indicates a hazard that could result in injury or death.
Page 5 : Cruise Control : Engine Coolant Temperature : Exterior Lamps : Fog Lamps : Fuel Gage : Fuses : Headlamp High/Low-Beam Changer : LATCH System Child Restraints : Malfunction Indicator Lamp : Oil Pressure : Power : Remote Vehicle Start >...
Page 6 ✍ NOTES...
Page 7: Table Of Contents
Instrument Panel ...1-2 Initial Drive Information ...1-4 Remote Keyless Entry (RKE) System ...1-4 Remote Vehicle Start ...1-4 Door Locks ...1-5 Windows ...1-6 Seat Adjustment ...1-6 Safety Belt ...1-8 Airbag On-Off Switch ...1-8 Sensing System for Passenger Airbag ...1-9 Mirror Adjustment ...1-9 Steering Wheel Adjustment ...1-10 Interior Lighting ...1-11 Exterior Lighting ...1-11...
Page 8: Instrument Panel
Instrument Panel...
Page 9 A. Outlet Adjustment on page 4-17. B. Driver Information Center (DIC) on page 4-37. C. Turn Signal/Multifunction Lever on page 4-4. D. Hazard Warning Flashers on page 4-3. E. Instrument Panel Cluster on page 4-21. F. Shift Lever. See Starting the Engine on page 3-23. G.
Page 10: Initial Drive Information
Initial Drive Information This section provides a brief overview about some of the important features that may or may not be on your speciﬁc vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual. Remote Keyless Entry (RKE) System The RKE transmitter is used to remotely lock and...
Page 11: Manual Door Locks
When the vehicle starts, the parking lamps will turn on and remain on as long as the engine is running. The doors will be locked and the climate control system may come on. The engine will continue to run for 10 minutes. Repeat the steps for a 10-minute time extension.
Page 12: Seat Adjustment
Windows Manual Windows Operate the manual windows by turning the hand crank on each door to raise or lower the side door windows. See Manual Windows on page 3-17. Power Windows If the vehicle has power windows, the controls are located on each of the side doors.
Page 13: Power Seats
Power Seats If the vehicle has front power seat(s), the controls are located at the front center of the seat cushion. Adjust the seat by moving the center knob up, down, right or left. Raise and lower the front or rear of the seat cushion by moving the right or left lever up or down.
Page 14: Safety Belt
Safety Belt Refer to the following sections for important information on how to use safety belts properly. • Safety Belts: They Are for Everyone on page 2-10. • How to Wear Safety Belts Properly on page 2-15. • Lap-Shoulder Belt on page 2-24. •...
Page 15: Sensing System For Passenger Airbag
Sensing System for Passenger Airbag The passenger sensing system, if equipped, will turn off the right front passenger frontal airbag under certain conditions. The driver airbag and roof-rail airbags, if equipped, are not affected by this. If the vehicle has a passenger sensing system, the passenger airbag status indicator will be visible on the instrument panel when the vehicle is started.
Page 16 Vehicles with towing mirrors can be adjusted manually for a clear view of the objects behind you. Manually fold the mirrors inward to prevent damage when going through an automatic car wash. To fold, pull the mirror toward the vehicle. Push the mirror outward, to return it to the original position.
Page 17: Interior Lighting
Interior Lighting Dome Lamp The dome lamps come on when any door is opened. They turn off after all the doors are closed. To manually turn on the dome lamps, turn the instrument panel brightness knob, located on the instrument panel to the left of the steering column, clockwise to the farthest position.
Page 18: Windshield Wiper/Washer
For more information, see: • Exterior Lamps on page 4-9. • Headlamps on Reminder on page 4-11. • Daytime Running Lamps (DRL) on page 4-11. • Automatic Headlamp System on page 4-11. Windshield Wiper/Washer The lever is located on the left side of the steering column.
Page 19 Vehicles With Air Conditioning A. Fan Control B. Temperature Control C. Air Delivery Mode Control D. Rear Window Defogger See Climate Control System on page 4-15. See Rear Heating System on page 4-18 (If Equipped) or Rear Air Conditioning and Heating System on page 4-19 (If Equipped).
Page 20: Portable Audio Devices
© ¨ : Seek or scan stations. : Press to display additional text information related to the current FM-RDS station or MP3 song. A choice of additional information such as: Channel, Song, Artist, and CAT (category) can display. Continue pressing to highlight the desired label, or press the softkey located under any one of the tabs and the information about that tab displays.
Page 21: Steering Wheel Controls
Steering Wheel Controls If equipped, these controls are located on the right side of the steering wheel. : Press to seek radio stations or select tracks on a CD. Press and hold to scan radio stations. : Press to mute the audio system. Press again to cancel mute.
Page 22: Performance And Maintenance
Power Outlets The accessory power outlets can be used to connect auxiliary electrical equipment, such as a cellular phone. The vehicle may have two accessory power outlets located on the instrument panel. To use the accessory power outlet lift the cover. See Accessory Power Outlet(s) on page 4-14 and Ashtray(s) and Cigarette Lighter on page 4-15 (If Equipped).
Page 23: Tire Pressure Monitor
Tire Pressure Monitor This vehicle may have a Tire Pressure Monitor System (TPMS). The Tire Pressure Monitor alerts you when a signiﬁcant reduction in pressure occurs in one or more of the vehicle’s tires by illuminating the low tire pressure warning light on the instrument cluster.
Page 24: Fuel E85 (85% Ethanol)
U.S.: 1-800-GMC-8782 (462-8782) TTY Users: 1-888-889-2438 Canada: 1-800-268-6800 As the owner of a new GMC, you are automatically enrolled in the Roadside Assistance program. This program provides technically trained advisors who are available 24 hours a day, 365 days a year, minor repair information or towing arrangements.
Page 25: Seats And Restraint System
Section 2 Head Restraints ...2-2 Front Seats ...2-2 Manual Seats ...2-2 Power Seat ...2-3 Reclining Seatbacks ...2-4 Rear Seats ...2-6 Rear Seat Operation ...2-6 Safety Belts ...2-10 Safety Belts: They Are for Everyone ...2-10 How to Wear Safety Belts Properly ...2-15 Lap-Shoulder Belt ...2-24 Safety Belt Use During Pregnancy ...2-29 Safety Belt Extender ...2-29...
Page 26: Head Restraints
Head Restraints On vehicles with factory installed seats, the front seats have built-in head restraints that are not adjustable in the outboard seating positions. Front Seats Manual Seats WARNING: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving.
Page 27: Power Seat
Power Seat If the vehicle has front power seat(s), the controls are located at the front center of the seat cushion. To raise or lower the seat, move the center knob up or down. To move the seat forward or rearward, move the center knob toward the right or left.
Page 28: Reclining Seatbacks
Reclining Seatbacks WARNING: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 29 WARNING: Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body.
Page 30: Rear Seats
Rear Seats Rear Seat Operation Removing the Rear Seat Disconnect the quick release latch plates for the lap-shoulder belts on the bench seat to be removed. 1. To do this, press the tip of a key into the release hole of the safety belt buckle while pulling up on the safety belt.
Page 31 Three Passenger Seat Shown The passenger side pin has a black cap with a white “R” marked on it. On a four passenger seat, each half of the seat has a set of pins. The driver side has a set marked “L”, and the passenger side has a set marked “R”.
Page 32 Replacing the Rear Seats WARNING: A seat that is not locked into place properly can move around in a collision or sudden stop. People in the vehicle could be injured. Be sure to lock the seat into place properly when installing it. WARNING: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection...
Page 33 Three Passenger Seat Shown 4. Push the pin(s) marked “R” down until they are in the retaining clip. Three Passenger Seat Shown 5. Push the pin(s) marked “L” down until they are in the retaining clip. 6. If the vehicle has a ﬂoor mat, put the ﬂap back to its original position.
Page 34: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. WARNING: Do not let anyone ride where a safety belt cannot be worn properly.
Page 35: Why Safety Belts Work
In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: You never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Page 36 Put someone on it. 2-12 Get it up to speed. Then stop the vehicle. The rider does not stop.
Page 37 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 2-13...
Page 38: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. 2-14 Questions and Answers About Safety Belts...
Page 39: How To Wear Safety Belts Properly
If I am a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt.
Page 40 Sit up straight and always keep your feet on the ﬂoor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Page 41 What is wrong with this? The shoulder belt is too loose. It will not give as much protection this way. WARNING: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 42 What is wrong with this? The lap belt is too loose. It will not give nearly as much protection this way. 2-18 WARNING: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Page 43 What is wrong with this? The belt is buckled in the wrong buckle. WARNING: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Page 44 What is wrong with this? The belt is over an armrest. 2-20 WARNING: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Page 45 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. WARNING: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 46 What is wrong with this? The belt is behind the body. 2-22 WARNING: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 47 What is wrong with this? The belt is twisted across the body. WARNING: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to ﬁx it.
Page 48: Lap-Shoulder Belt
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. If you are using a rear seating position with a detachable safety belt and the safety belt is not attached, see Rear Seat Operation on page 2-6 for instruction on reconnecting the safety belt to the mini-buckle.
Page 49 5. To make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. To unlatch the belt, push the button on the buckle. The belt should return to its stowed position.
Page 50 Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder. The belt should be away from the face and neck, but not falling off of the shoulder.
Page 51: Rear Safety Belt Comfort Guides
Rear Safety Belt Comfort Guides This vehicle may have rear shoulder belt comfort guides. If not, they are available through your dealer/retailer. The guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults. When installed and properly adjusted, the comfort guide positions the shoulder belt away from the neck and head.
Page 52 3. Be sure that the belt is not twisted and it lies ﬂat. The elastic cord must be under the belt and the guide on top. WARNING: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
Page 53: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
Page 54: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. 2-30 The manufacturer’s instructions that come with the booster seat state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below ﬁt test: •...
Page 55 What is the proper way to wear safety belts? An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should ﬁt snugly below the hips, just touching the top of the thighs.
Page 56 WARNING: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Page 57: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 58 WARNING: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 110 kg (240 lb) force on a person’s arms.
Page 59 WARNING: Never do this. Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Page 60 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 61: Child Restraint Systems
WARNING: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
Page 62 A forward-facing child seat (B) provides restraint for the child’s body with the harness. 2-38 A booster seat (C-D) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. A booster seat can also help a child to see out the window.
Page 63 Securing an Add-On Child Restraint in the Vehicle WARNING: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle. Secure the child restraint properly in the vehicle using the vehicle’s safety belt or LATCH system, following the instructions that came with that child restraint and the instructions in this manual.
Page 64: Where To Put The Restraint
Securing the Child Within the Child Restraint WARNING: A child can be seriously injured or killed in a crash if the child is not properly secured in the child restraint. Secure the child properly following the instructions that came with that child restraint. 2-40 Where to Put the Restraint According to accident statistics, children and infants...
Page 65 A label on the sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. WARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inﬂates.
Page 66: Lower Anchors And Tethers For Children (Latch)
Lower Anchors and Tethers for Children (LATCH) The LATCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier. The LATCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LATCH system.
Page 67 Lower Anchors Lower anchors (A) are metal bars built into the vehicle. There are two lower anchors for each LATCH seating position that will accommodate a child restraint with lower attachments (B). Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle.
Page 68 Some child restraints that have a top tether are designed for use with or without the top tether being attached. Others require the top tether always to be attached. In Canada, the law requires that forward-facing child restraints have a top tether, and that the tether be attached.
Page 69 Second, Third and Fourth Row with Three Passenger Seat — Passenger Van There are two top tether anchors in the second, third and fourth rows. To install a child restraint in the rear driver side seating positions, use anchor point (A). To install a child restraint in the rear passenger side seating positions, use anchor point (B).
Page 70: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed for the LATCH System WARNING: If a LATCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Install a LATCH-type child restraint properly using the anchors, or use the vehicle’s safety belts to secure the restraint, following the instructions that came...
Page 71 Notice: Do not let the LATCH attachments rub against the vehicle’s safety belts. This may damage these parts. If necessary, move buckled safety belts to avoid rubbing the LATCH attachments. Do not fold the empty rear seat with a safety belt buckled.
Page 72 If the position you are using does not have a headrest or head restraint and you are using a dual tether, route the tether over the seatback. If the position you are using has an integrated headrest or head restraint and you are using a dual tether, route the tether around the headrest or...
Page 73: Securing A Child Restraint In A Rear Seat Position
Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating position, study the instructions that came with the child restraint to make sure it is compatible with this vehicle. If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 2-42 for how and where to install the child restraint using LATCH.
Page 74 3. Push the latch plate into the buckle until it clicks. 4. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.
Page 75 5. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 76: Securing A Child Restraint In The Right Front Seat Position (With Passenger Sensing System)
Securing a Child Restraint in the Right Front Seat Position (With Passenger Sensing System) This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 2-40. In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag under certain conditions.
Page 77 WARNING: (Continued) Secure rear-facing child restraints in a rear seat, even if the airbag is off. If you secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat.
Page 78 4. Push the latch plate into the buckle until it clicks. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.
Page 79 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 80: Securing A Child Restraint In The Right Front
Securing a Child Restraint in the Right Front Seat Position (With Airbag On-Off Switch) The vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 2-40. There is a switch on the instrument panel that you can use to turn off the right front passenger’s frontal airbag.
Page 81 WARNING: If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. For example, the right front passenger airbag could inﬂate even though the airbag on-off switch is turned off. To help avoid injury to yourself or others, have the vehicle serviced right away.
Page 82 4. Push the latch plate into the buckle until it clicks. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary.
Page 83 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 84: Airbag System
Airbag System The vehicle has the following airbag: • A frontal airbag for the driver. The vehicle may have the following airbags: • A frontal airbag for the right front passenger. • A roof-rail airbag for the driver (cargo van). •...
Page 85 Here are the most important things to know about the airbag system: WARNING: You can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
Page 86: Where Are The Airbags
WARNING: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 87 If the vehicle has one, the right front passenger airbag is in the instrument panel on the passenger side. Driver Side shown, Passenger Side similar If the vehicle is a cargo or passenger van with a sliding door and it has a roof-rail airbag for the driver and right front passenger position, the roof-rail airbags are in the ceiling above the side window.
Page 88 Driver Side shown, Passenger Side similar If the vehicle has roof-rail airbags for the driver, right front passenger, passengers behind the driver and right front passenger, and the third row outboard passengers, the roof-rail airbags are in the ceiling above the side windows.
Page 89: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? Frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inﬂate if the impact exceeds a predetermined deployment threshold.
Page 90: What Makes An Airbag Inﬂate
In addition, the vehicle may have dual-stage frontal airbags. Dual-stage airbags adjust the restraint according to crash severity. The vehicle has electronic frontal sensors, which help the sensing system distinguish between a moderate frontal impact and a more severe frontal impact. For moderate frontal impacts, dual-stage airbags inﬂate at a level less than full deployment.
Page 91: What Will You See After An Airbag Inﬂates
Rollover capable roof-rail airbags are designed to help contain the head and chest of occupants in the outboard seating positions in the ﬁrst, second, and third rows, if equipped. The rollover capable roof-rail airbags are designed to help reduce the risk of full or partial ejection in rollover events, although no system can prevent all such ejections.
Page 92 WARNING: A crash severe enough to inﬂate the airbags may have also damaged important functions in the vehicle, such as the fuel system, brake and steering systems, etc. Even if the vehicle appears to be drivable after a moderate crash, there may be concealed damage that could make it difficult to safely operate the vehicle.
Page 93: Airbag Off Switch
Airbag Off Switch If the instrument panel has one of the switches pictured in the following illustrations, the vehicle has an airbag on-off switch that you can use to manually turn on or off the right front passenger airbag. United States If the vehicle does not have an airbag on-off switch, it may have a passenger sensing system.
Page 94 Medical Condition. A passenger has a medical condition which, according to his or her physician: • Causes the passenger airbag to pose a special risk for the passenger; and • Makes the potential harm from the passenger airbag in a crash greater than the potential harm from turning off the airbag and allowing the passenger, even if belted, to hit the dashboard or windshield in a crash.
Page 95 WARNING: If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system. For example, the right front passenger airbag could inﬂate even though the airbag on-off switch is turned off. To help avoid injury to yourself or others, have the vehicle serviced right away.
Page 96: Passenger Sensing System
Passenger Sensing System If the instrument panel has one of the indicators pictured in the following illustrations, the vehicle has a passenger sensing system unless there is an airbag off switch located on the instrument panel. If there is an airbag off switch, the vehicle does not have a passenger sensing system.
Page 97 WARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front passenger airbag inﬂates and the passenger seat is in a forward...
Page 98 The passenger sensing system is designed to turn on (may inﬂate) the right front passenger frontal airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger seat. When the passenger sensing system has allowed the airbag to be enabled, the on indicator will light and stay lit to remind you that the airbag is active.
Page 99 If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. Turn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
Page 100: Additional Factors Affecting System Operation
If the Off Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. 2-76 If this happens, use the following steps to allow the system to detect that person and enable the right front...
Page 101: Servicing Your Airbag-Equipped Vehicle
A thick layer of additional material, such as a blanket or cushion, or aftermarket equipment such as seat covers, seat heaters, and seat massagers can affect how well the passenger sensing system operates. We recommend that you not use seat covers or other aftermarket equipment except when approved by GM for your speciﬁc vehicle.
Page 102: Adding Equipment To Your Airbag-Equipped Vehicle
Adding Equipment to Your Airbag-Equipped Vehicle Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? Yes. If you add things that change the vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Page 103: Restraint System Check
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Page 104: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash WARNING: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as...
Page 105: Features And Controls
Section 3 Keys ...3-3 Remote Keyless Entry (RKE) System ...3-4 Remote Keyless Entry (RKE) System Operation ...3-4 Remote Vehicle Start ...3-6 Doors and Locks ...3-8 Door Locks ...3-8 Power Door Locks ...3-9 Cargo Door Relocking ...3-9 Delayed Locking ...3-9 Programmable Automatic Door Locks ...3-10 Automatic Door Lock ...3-10 Automatic Door Unlock ...3-10 Rear Door Security Locks ...3-11...
Page 106 Section 3 Mirrors ...3-40 Manual Rearview Mirror ...3-40 Outside Manual Mirrors ...3-40 Outside Towing Mirrors ...3-40 Features and Controls Outside Power Mirrors ...3-41 Outside Convex Mirror ...3-41 Outside Heated Mirrors ...3-42 Storage Areas ...3-42...
Page 107: Keys
Keys WARNING: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Page 108: Remote Keyless Entry (Rke) System
Remote Keyless Entry (RKE) System See Radio Frequency Statement on page 8-18 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/211 of Industry and Science Canada. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment.
Page 109 The horn may chirp when is pressed again within ﬁve seconds. See DIC Vehicle Customization on page 4-52 for additional information. (Unlock): Press to unlock the driver door. If pressed again within ﬁve seconds, all remaining doors unlock. The interior lamps come on and stay on for 20 seconds or until the ignition is turned on.
Page 110: Remote Vehicle Start
Battery Replacement Replace the battery if the REPLACE BATTERY IN REMOTE KEY message displays in the DIC. See “REPLACE BATTERY IN REMOTE KEY” under DIC Warnings and Messages on page 4-44 for additional information. Notice: When replacing the battery, do not touch any of the circuitry on the transmitter.
Page 111 There are other conditions which can affect the performance of the transmitter, see Remote Keyless Entry (RKE) System on page 3-4 for additional information. (Remote Vehicle Start): This button will be on the RKE transmitter if you have remote start. To start the engine using the remote start feature: 1.
Page 112: Doors And Locks
The remote vehicle start feature will not operate if: • The remote start system is disabled through the DIC. • The vehicle’s key is in the ignition. • The vehicle’s hood is open • The hazard warning ﬂashers are on. •...
Page 113: Power Door Locks
To lock the door from the inside, slide the manual lever on the door down. To unlock the door, slide the manual lever up. From the outside, use the key. If the vehicle is equipped with keyless entry, see Remote Keyless Entry (RKE) System on page 3-4 for more information.
Page 114: Programmable Automatic Door Locks
Programmable Automatic Door Locks The vehicle is programmed so that when the doors are closed, the ignition is on and the shift lever is moved out of P (Park), all the doors will lock. The doors will unlock every time you stop the vehicle and move the shift lever back into P (Park).
Page 115: Rear Door Security Locks
Rear Door Security Locks Security locks are located on the front portion of the 60/40 side swing-out door or the side sliding door. For the 60/40 side swing-out door, move the button to the right for the driver side door or to the left for the passenger side door to engage the security feature.
Page 116: Lockout Protection
Lockout Protection This feature protects you from locking the key in the vehicle when the key is in the ignition and a door is open. If the power lock switch is pressed when either the driver, passenger, or rear door is open, all the doors will lock and then the driver door will unlock.
Page 117: 60/40 Swing-Out Side Door
To open the sliding side door from the inside, pull the handle toward the rear of the vehicle. Then, slide the door toward the rear of the vehicle. To close the sliding side door from the inside, grasp the handle and slide the door toward the front of the vehicle.
Page 118 To open the front portion of a 60/40 door from the inside, pull the handle toward you and push the door open. 3-14 To open the rear portion of a 60/40 door from the outside, pull the handle on the side of the rear door and pull the door toward you.
Page 119: Rear Doors
Rear Doors WARNING: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Page 120: Windows
Windows WARNING: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 121: Manual Windows
Manual Windows Operate the manual windows by turning the hand crank on each door to raise or lower the side door windows. Power Windows WARNING: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed.
Page 122: Swing-Out Windows
Express-Down The driver window switch also has an express-down feature that allows the window to be lowered without holding the switch. Press fully and release the window switch marked AUTO to activate the express-down mode. This mode can be cancelled at any time by pulling up on the switch.
Page 123: Enhanced Technology Glass
Rear Swing-Out Windows The vehicle also has rear swing-out windows. The rear swing-out windows work the same way as the side swing out window, but the latch is located at the bottom edge of the window. Enhanced Technology Glass The vehicle may be equipped with Enhanced Technology Glass (ETG).
Page 124: Sun Visors
Sun Visors To block out glare, swing down the sun visors. You can also swing them to the side. Visor Vanity Mirror The vehicle may have visor vanity mirrors, with or without lamps. Lift the mirror cover to turn the lamps on, if equipped.
Page 125 If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the instrument panel PASS KEY fuse. If the engine still does not start with the other key, your vehicle needs service.
Page 126: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Keep your speed at 55 mph (88 km/h) or less for the ﬁrst 500 miles (805 km).
Page 127: Retained Accessory Power (Rap)
B (ACC/ACCESSORY): This is the position in which you can operate things like the radio and the windshield wipers when the engine is off. C (ON/RUN): This position can be used to operate the electrical accessories and to display some instrument panel cluster warning and indicator lights.
Page 128 Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition key to START. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Do not race the engine immediately after starting it.
Page 129: Fast Idle System
Fast Idle System Fast Idle System with Switch If the vehicle has this feature it is available only with cruise control. The manual fast idle switch is operated using the cruise control buttons located on the left hand side of the steering wheel. This system can be used to increase engine idle speed whenever the following conditions are met: •...
Page 130: Automatic Transmission Operation (Six Speed Automatic Transmission)
To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord for the engine coolant heater is located on the driver side of the engine compartment and is attached to the hose for the power steering reservoir. 3.
Page 131 WARNING: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly.
Page 132 D (Drive): This position is for normal driving. It provides the best fuel economy. If you need more power for passing, and you are: • Going less than about 35 mph (55 km/h), push the accelerator pedal about halfway down. •...
Page 133 3 (Third): This position is also used for normal driving. It reduces vehicle speed more than D (Drive) without using the brakes. You might choose 3 (Third) instead of D (Drive) when driving on hilly, winding roads, when towing a trailer, so there is less shifting between gears and when going down a steep hill.
Page 134 To use this feature, do the following: 1. Move the shift lever to M (Manual Mode). 2. Press the plus/minus buttons, located on the steering column shift lever, to select the desired range of gears for current driving conditions. When M (Manual Mode) is selected a number displays in the DIC next to the M indicating the current gear.
Page 135 Automatic Transmission Operation (Four Speed Automatic Transmission) There are several different positions for your shift lever. P (Park): This position locks your rear wheels. It is the best position to use when you start the engine because the vehicle cannot move easily. WARNING: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake...
Page 136 R (Reverse): Use this gear to back up. Notice: Shifting to R (Reverse) while the vehicle is moving forward could damage the transmission. The repairs would not be covered by the vehicle warranty. Shift to R (Reverse) only after the vehicle is stopped.
Page 137: Tow/Haul Mode
2 (Second): This position reduces vehicle speed even more than 3 (Third) without using the brakes. You can use 2 (Second) on hills. It can help control vehicle speed as you go down steep mountain roads, but then you would also want to use the brakes off and on. You may use this feature for reducing torque to the rear wheels when you are trying to start the vehicle from a stop on slippery road surfaces.
Page 138 See Tow/Haul Mode Light on page 4-36 for more information. Also see “Tow Haul Mode” under Towing a Trailer on page 5-26 for more information. Grade Braking (Six Speed Automatic Transmission) The Grade Braking shift modes can be activated by pressing the tow/haul button on the dash.
Page 139: Parking Brake
Parking Brake To set the parking brake, hold the regular brake pedal, then push down the parking brake pedal. If the ignition is on, the brake system warning light will come on. To release the parking brake, hold the regular brake pedal down.
Page 140: Shifting Into Park
Shifting Into Park WARNING: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 141: Shifting Out Of Park
Torque Lock If you are parking on a hill and you do not shift the vehicle into P (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of P (Park).
Page 142: Parking Over Things That Burn
Parking Over Things That Burn WARNING: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust WARNING: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Page 143: Running The Vehicle While Parked
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. WARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Page 144: Mirrors
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind. Push the tab forward for daytime use and pull it for nighttime use.
Page 145: Outside Power Mirrors
Outside Power Mirrors Vehicles with outside power mirrors have controls located on the driver side door. Select each mirror by turning the knob clockwise for the passenger side mirror or counterclockwise for the driver side mirror. The center position is neutral. Then, adjust the mirror angle by moving the knob in the desired direction.
Page 146: Outside Heated Mirrors
Outside Heated Mirrors For vehicles with heated mirrors: < (Rear Defogger): Press to heat the mirrors. An indicator light in the button lights when the outside heated mirrors are activated. See “Rear Window Defogger” under Climate Control System on page 4-15 for more information. 3-42 Storage Areas Your vehicle may have a front storage compartment.
Page 147 Section 4 Instrument Panel Overview ...4-3 Hazard Warning Flashers ...4-3 Horn ...4-3 Tilt Wheel ...4-3 Turn Signal/Multifunction Lever ...4-4 Turn and Lane-Change Signals ...4-4 Headlamp High/Low-Beam Changer ...4-5 Flash-to-Pass ...4-5 Windshield Wipers ...4-5 Windshield Washer ...4-6 Cruise Control ...4-6 Exterior Lamps ...4-9 Headlamps on Reminder ...4-11 Daytime Running Lamps (DRL) ...4-11 Automatic Headlamp System ...4-11...
Page 148 Section 4 Brake System Warning Light ...4-28 Antilock Brake System (ABS) Warning Light ...4-29 ® StabiliTrak Indicator Light ...4-29 Engine Coolant Temperature Gage ...4-30 Tire Pressure Light ...4-30 Malfunction Indicator Lamp ...4-31 Oil Pressure Gage ...4-34 Oil Pressure Light ...4-35 Security Light ...4-35 Cruise Control Light ...4-36 Highbeam On Light ...4-36...
Page 149: Instrument Panel Overview
Instrument Panel Overview Hazard Warning Flashers (Hazard Warning Flasher): Press this button located on top of the steering column, to make the front and rear turn signal lamps ﬂash on and off. This warns others that you are having trouble. Press again to turn the ﬂashers off.
Page 150: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: : Turn and Lane Change Signals. : Headlamp High/Low-Beam Changer. : Windshield Wipers. : Windshield Washer. Flash-to-Pass Feature. Information for these features is on the pages following. Turn and Lane-Change Signals : An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change.
Page 151: Headlamp High/Low-Beam Changer
Headlamp High/Low-Beam Changer (Headlamp High/Low-Beam Changer): Pull the turn signal lever all the way toward you to change the headlamps from low to high beam. Then release it. This instrument panel cluster light comes on when the high beam headlamps are on. Flash-to-Pass This feature is used to signal to the vehicle ahead that you want to pass.
Page 152: Windshield Washer
Windshield Washer The windshield wiper paddle is located on top of the multifunction lever. (Washer Fluid): Push the paddle to spray washer ﬂuid on the windshield. The wipers will clear the window and then either stop or return to the preset speed. WARNING: In freezing weather, do not use your washer until the windshield is warmed.
Page 153: Setting Cruise Control
The cruise control buttons are located on left side of the steering wheel. (On/Off): This button can both activate and turn off the system. The indicator light on the button turns on when cruise control is on and turns off when cruise control is off.
Page 154 Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied, this shuts off the cruise control. But it does not need to be reset. Once the vehicle speed reaches about 25 mph (40 km/h) or more, press the +RES button on the steering wheel.
Page 155: Exterior Lamps
Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain the vehicle’s speed.
Page 156 The exterior lamps control has four positions: (Off): Brieﬂy turn the control to this position to turn the automatic headlamps and daytime running lamps (DRL) off or back on. For vehicles ﬁrst sold in Canada, the off position only works for vehicles that are shifted into the P (Park) position.
Page 157: Headlamps On Reminder
Headlamps on Reminder If a door is open, a reminder chime sounds when the headlamps or parking lamps are manually turned on and the key is out of the ignition. To turn off the chime, turn the headlamp switch to off or auto and then back on, or close and re-open the door.
Page 158: Instrument Panel Brightness
There is a delay in the transition between the daytime and nighttime operation of the Daytime Running Lamps (DRL) and the automatic headlamp systems so that driving under bridges or bright overhead street lights does not affect the system. The DRL and automatic headlamp system is only affected when the light sensor sees a change in lighting lasting longer than the delay.
Page 159: Dome Lamp Override
Dome Lamp Override The dome lamp override button is located next to the exterior lamps control. The dome lamp override sets the dome lamps to remain off or come on automatically when a door is opened. (Dome Lamp Override): Press the button in and the dome lamps remain off when a door is opened.
Page 160: Battery Run-Down Protection
A high electrical load occurs when several of the following are on, such as: headlamps, high beams, fog lamps, rear window defogger, climate control fan at high speed, heated seats, engine cooling fans, trailer loads, and loads plugged into accessory power outlets. EPM works to prevent excessive discharge of the battery.
Page 161: Ashtray(S) And Cigarette Lighter
Ashtray(s) and Cigarette Lighter For vehicles with an ashtray it is located in the center console or on the instrument panel. Pull up on the ashtray door to open it if it is in the console or pull the door open it if it is on the instrument panel. Notice: If papers, pins, or other ﬂammable items are put in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly...
Page 162 Air Delivery Mode Control: Turn the knob clockwise or counterclockwise to change the current airﬂow mode. (Vent): Air is directed to the instrument panel outlets. (Bi-Level): Air is divided between the instrument panel and ﬂoor outlets, with some air directed toward the windshield.
Page 163: Outlet Adjustment
Rear Window Defogger For vehicles with a rear window defogger, a warming grid is used to remove fog or frost from the rear window. It only works when the ignition is in ON/RUN. < (Rear Window Defogger): Press to turn the rear window defogger on or off.
Page 164: Rear Heating System
Rear Heating System For vehicles with a rear heating system, it lets you adjust the amount of air ﬂowing into the rear of the vehicle, from the front-seating area. This feature works with the main climate-control system in the vehicle. 4-18 AUX: The thumbwheel for this system is located in the switchbank below the audio system.
Page 165: Rear Air Conditioning And Heating System
Rear Air Conditioning and Heating System For vehicles with a rear heating and air-conditioning system, it maintains the temperature, fan speed and air delivery for the rear-seat passengers only. It also works with the main climate-control system in the vehicle. Front Climate Control Panel Use this control panel to maintain a separate temperature setting.
Page 166: Warning Lights, Gages, And Indicators
(Fan Control): Turn clockwise or counterclockwise to increase or decrease the fan speed in the rear-seating area. Temperature Control: Turn clockwise or counterclockwise to increase or decrease the temperature in the rear-seating area. The air-conditioning system on the main climate control panel must be turned on to direct cooled air to the rear of the vehicle.
Page 167: Instrument Panel Cluster
Instrument Panel Cluster United States 4-Speed Version shown, 6-Speed and Canada similar 4-21...
Page 168: Speedometer And Odometer
Speedometer and Odometer The speedometer shows the vehicle speed in both miles per hour (mph) and kilometers per hour (km/h). The odometer shows how far the vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). This vehicle has a tamper resistant odometer.
Page 169: Safety Belt Reminders
Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind a driver to fasten the safety belt, unless the driver safety belt is already buckled. The safety belt light comes on and stays on for several seconds, then ﬂashes for several more.
Page 170: Airbag Off Light
The airbag readiness light ﬂashes for a few seconds when the engine is started. If the light does not come on then, have it ﬁxed immediately. WARNING: If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly.
Page 171 WARNING: If the right front passenger’s airbag is turned off for a person who is not in a risk group identiﬁed by the national government, that person will not have the extra protection of an airbag. In a crash, the airbag will not be able to inﬂate and help protect the person sitting there.
Page 172: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator If the vehicle has a passenger sensing system, the instrument panel will have a passenger airbag status indicator. See Passenger Sensing System on page 2-72 for important safety information. The instrument panel has a passenger airbag status indicator. United States When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on...
Page 173: Charging System Light
Charging System Light This light comes on brieﬂy when the ignition key is turned to START, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer.
Page 174: Brake System Warning Light
The vehicle can be only driven for a short time with the reading in either warning zone. If it must be driven, turn off all unnecessary accessories. Readings in either warning zone indicate a possible problem in the electrical system. Have the vehicle serviced as soon as possible.
Page 175: Antilock Brake System (Abs) Warning Light
Antilock Brake System (ABS) Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on brieﬂy when the engine is started. If it does not, have the vehicle serviced by your dealer/retailer. If the system is working normally the indicator light then goes off.
Page 176: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage United States This gage shows the engine coolant temperature. It also provides an indicator of how hard the vehicle is working. During a majority of the operation, the gage will read 100°C (210°F) or less. If the vehicle is pulling a load or going up hills, it is normal for the temperature to ﬂuctuate and approach the 122°C (250°F) mark.
Page 177: Malfunction Indicator Lamp
When the Light is On Steady This indicates that one or more of the tires are signiﬁcantly underinﬂated. A tire pressure message in the Driver Information Center (DIC), can accompany the light. See Driver Information Center (DIC) on page 4-37 for more information.
Page 178 Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle. This system assists the service technician in correctly diagnosing any malfunction. Notice: If the vehicle is continually driven with this light on, after a while, the emission controls might not work as well, the vehicle’s fuel economy might not be as good, and the engine might not...
Page 179 An emission system malfunction might be corrected by doing the following: • Make sure the fuel cap is fully installed. See Filling the Tank on page 6-10. The diagnostic system can determine if the fuel cap has been left off or improperly installed.
Page 180: Maintenance Schedule
Oil Pressure Gage United States The oil pressure gage shows the engine oil pressure in psi (pounds per square inch) when the engine is running. Canadian vehicles indicate pressure in kPa (kilopascals). Oil pressure may vary with engine speed, outside temperature and oil viscosity, but readings above the low pressure zone indicate the normal operating range.
Page 181: Maintenance Schedule
Oil Pressure Light WARNING: Do not keep driving if the oil pressure is low. The engine can become so hot that it catches ﬁre. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced. Notice: Lack of proper engine oil maintenance can damage the engine.
Page 182: Cruise Control Light
Cruise Control Light The cruise control light comes on whenever the cruise control is set. The light goes out when the cruise control is turned off. See Cruise Control on page 4-6 for more information. Highbeam On Light This light comes on when the high-beam headlamps are in use.
Page 183: Driver Information Center (Dic)
An arrow on the fuel gage indicates the side of the vehicle the fuel door is on. The gage ﬁrst indicates empty before the vehicle is out of fuel, and the fuel tank should be refueled soon. Listed are four situations customers might experience with the fuel gage.
Page 184: Dic Operation And Displays
DIC Operation and Displays The DIC has different displays which can be accessed by pressing the DIC buttons located on the instrument panel, next to the instrument panel cluster. DIC Buttons The buttons are the trip/fuel, vehicle information, customization, and set/reset buttons. The button functions are detailed in the following pages.
Page 185: Trip Odometers
Trip Odometers Press the trip/fuel button until A or B displays. This display shows the current distance traveled in either kilometers (km) or miles (mi) since the last reset for each trip odometer. Both trip odometers can be used at the same time.
Page 186 Average Economy Press the trip/fuel button until AVG ECONOMY displays. This display shows the approximate average liters per 100 kilometers (L/100 km) or miles per gallon (mpg). This number is calculated based on the number of L/100 km (mpg) recorded since the last time this menu item was reset.
Page 187: Tire Pressure
Vehicle Information Menu Items (Vehicle Information): Press this button to scroll through the following menu items: Oil Life Press the vehicle information button until OIL LIFE REMAINING displays. This display shows an estimate of the oil’s remaining useful life. If you see 99% OIL LIFE REMAINING on the display, that means 99% of the current oil life remains.
Page 188 Engine Hours Press the vehicle information button until ENGINE HOURS displays. This display shows the total number of hours the engine has run. Relearn Tire Positions Your vehicle may have this display. To access this display, the vehicle must be in P (Park). If your vehicle has the Tire Pressure Monitor System (TPMS), after rotating the tires or after replacing a tire or sensor, the system must re-learn the tire positions.
Page 189: Dic Compass
DIC Compass Your vehicle may have a compass in the Driver Information Center (DIC). Compass Zone Your dealer/retailer will set the correct zone for your location. Under certain circumstances, such as during a long distance cross-country trip or moving to a new state or province, it will be necessary to compensate for compass variance by resetting the zone through the DIC if the zone is not set correctly.
Page 190: Dic Warnings And Messages
Compass Calibration The compass can be manually calibrated. Only calibrate the compass in a magnetically clean and safe location, such as an open parking lot, where driving the vehicle in circles is not a danger. It is suggested to calibrate away from tall buildings, utility wires, manhole covers, or other industrial structures, if possible.
Page 191 Some messages cannot be cleared from the DIC display because they are more urgent. These messages require action before they can be cleared. You should take any messages that appear on the display seriously and remember that clearing the messages will only make the messages disappear, not correct the problem.
Page 192 indicate which tire needs to be checked. You can receive more than one tire pressure message at a time. To read the other messages that may have been sent at the same time, press the set/reset button. If a tire pressure message appears on the DIC, stop as soon as you can.
Page 193: Engine Overheated Stop Engine
ENGINE OVERHEATED STOP ENGINE Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible. See Engine Overheating on page 6-33 for more information.
Page 194: Oil Pressure Low Stop Engine
OIL PRESSURE LOW STOP ENGINE Notice: If you drive your vehicle while the engine oil pressure is low, severe engine damage may occur. If a low oil pressure warning appears on the Driver Information Center (DIC), stop the vehicle as soon as possible. Do not drive the vehicle until the cause of the low oil pressure is corrected.
Page 195: Service Air Bag
SERVICE AIR BAG This message displays if there is a problem with the airbag system. Have your dealer/retailer inspect the system for problems. See Airbag Readiness Light on page 4-23 and Airbag System on page 2-60 for more information. SERVICE BATTERY CHARGING SYSTEM On some vehicles, this message displays if there is a problem with the battery charging system.
Page 196: Service Transmission
information. If the warning comes on and stays on, there may be a problem with the TPMS. See your dealer/retailer. SERVICE TRACTION CONTROL If your vehicle has StabiliTrak, this message displays when there is a problem with the Traction Control System (TCS).
Page 197: Traction Control Off
• The message could display if the stability system takes longer than usual to complete its diagnostic checks due to driving conditions. • The message displays if an engine or vehicle related problem has been detected and the vehicle needs service. See your dealer/retailer. The message turns off as soon as the conditions that caused the message to be displayed are no longer present.
Page 198: Dic Vehicle Customization
TRANSMISSION HOT IDLE ENGINE Notice: If you drive your vehicle while the transmission ﬂuid is overheating and the transmission temperature warning is displayed on the instrument panel cluster and/or DIC, you can damage the transmission. This could lead to costly repairs that would not be covered by your warranty.
Page 199 Entering the Feature Settings Menu 1. Turn the ignition on and place the vehicle in P (Park). To avoid excessive drain on the battery, it is recommended that the headlamps are turned off. 2. Press the customization button to enter the feature settings menu.
Page 200 AUTO DOOR LOCK This feature allows you to select when the vehicle’s doors will automatically lock. See Programmable Automatic Door Locks on page 3-10 for more information. Press the customization button until AUTO DOOR LOCK appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Page 201: Remote Door Unlock
REMOTE DOOR LOCK This feature allows you to select the type of feedback you will receive when locking the vehicle with the Remote Keyless Entry (RKE) transmitter. You will not receive feedback when locking the vehicle with the RKE transmitter if the doors are open. See Remote Keyless Entry (RKE) System Operation on page 3-4 for more information.
Page 202: Exit Lighting
NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. DELAY DOOR LOCK This feature allows you to select whether or not the locking of the vehicle’s doors will be delayed.
Page 203 NO CHANGE: No change will be made to this feature. The current setting will remain. To select a setting, press the set/reset button while the desired setting is displayed on the DIC. APPROACH LIGHTING This feature allows you to select whether or not to have the exterior lights turn on brieﬂy during low light periods after unlocking the vehicle using the Remote Keyless Entry (RKE) transmitter.
Page 204: Factory Settings
FACTORY SETTINGS This feature allows you to set all of the customization features back to their factory default settings. Press the customization button until FACTORY SETTINGS appears on the DIC display. Press the set/reset button once to access the settings for this feature.
Page 205: Audio System(S)
Audio System(s) If the vehicle came without a radio, the wiring provisions for a radio and an antenna were installed at the assembly plant, so that if you want, a radio can be installed at the dealer/retailer. Determine which radio the vehicle has and read the following pages to become familiar with its features.
Page 206: Setting The Clock
Setting the Clock AM/FM Radio with Optional CD Player If your vehicle has an AM/FM radio with an optional CD player, it has a button for setting the time. With these types of radios, the clock can be set with either the radio turned on or off.
Page 207 Changing the Time and Date Default Settings You can change the time default setting from 12 hours to 24 hours or change the date default setting from month/day/year to day/month/year. To change the time or date default settings, follow these instructions: 1.
Page 208: Radio(S)
Changing the Time and Date Default Settings To change the time default setting from 12 hours to 24 hours or change the date default setting from month/day/year to day/month/year. To change the time or date default settings, follow these instructions: 1.
Page 209: Playing The Radio
Radio with CD (MP3) shown, Radio with Six-Disc CD (MP3) similar The vehicle has one of these radios as its audio system. Radio Data System (RDS) The Radio may have a Radio Data System (RDS). The RDS feature is available for use only on FM stations that broadcast RDS information.
Page 210: Finding A Station
(Clock) (AM-FM Radio and Radio with CD (Base)): The radio has a clock button for setting the time. With this type of radio, the clock can be set with either the radio turned on or off. See Setting the Clock on page 4-60 for more information. Speed Compensated Volume (SCV): Radios with Speed Compensated Volume (SCV) automatically adjusts the radio volume to compensate for road and...
Page 211: Setting Preset Stations
Setting Preset Stations If the radio does not have a FAV button, up to 18 stations (six FM1, six FM2, and six AM), can be programmed on the six numbered pushbuttons, by performing the following steps: 1. Turn the radio on. 2.
Page 212: Setting The Tone
The number of favorites pages can be setup using the MENU button. To setup the number of favorites pages: 1. Press the MENU button to display the radio setup menu. 2. Press the pushbutton located below the FAV 1-6 label. 3.
Page 213: Radio Messages
Adjusting the Speakers (Balance/Fade) (AM-FM Radio and Radio with CD (Base)) (Balance/Fade): To adjust the balance or fade, press the button or the knob until the desired speaker control label displays. Turn the clockwise or counterclockwise to adjust the setting. Adjusting the Speakers (Balance/Fade) BAL/FADE (Balance/Fade): To adjust balance or fade, press the...
Page 214: Playing A Cd(S) (Six-Disc Cd Player)
Playing a CD(s) (Six-Disc CD Player) LOAD : Press to load CDs into the CD player. This CD player holds up to six CDs. To insert one CD, do the following: 1. Press and release the button. 2. Wait for the message to insert the disc. 3.
Page 215 Care of Your CD and DVD Player Do not add any label to a CD, it could get caught in the CD or DVD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen.
Page 216 To use random on an Uplevel Radio with a Single CD player, do the following: 1. Press the CD/AUX button, insert a disc partway into the slot of the CD player. A RDM label displays. 2. To play the tracks in random order, press the pushbutton positioned under the RDM label until Random Current Disc displays.
Page 217 CD Messages REMOVE/CHECK DISC: Radios with a Single CD player or radios with a Six-Disc player displays CHECK DISC and/or ejects the CD if an error occurs. ERR (Error): If this message displays and/or the CD comes out, it could be for one of the following reasons: •...
Page 218: Mp3 Format
BAND: Press to listen to the radio while a portable audio device is playing. The portable audio device continues playing, so you might want to stop it or turn it off. CD/AUX (CD/Auxiliary): Press to play a CD while a portable audio device is playing.
Page 219 • Minimize the length of the ﬁle, folder, or playlist names. Long ﬁle, folder, or playlist names, or a combination of a large number of ﬁles and folders, or playlists could cause the player to be unable to play up to the maximum number of ﬁles, folders, playlists, or sessions.
Page 220 Order of Play Tracks recorded to the CD-R or CD-RW are played in the following order: • Play begins from the ﬁrst track in the ﬁrst playlist and continues sequentially through all tracks in each playlist. When the last track of the last playlist has played, play continues from the ﬁrst track of the ﬁrst playlist.
Page 221 For the Six-Disc CD player, press and hold this button for two seconds to eject all discs. (Tune): Turn this knob to select MP3 ﬁles on the CD-R or CD-RW currently playing. © ¨ SEEK : Press the left SEEK arrow to go to the start of the current MP3 ﬁle, if more than 10 seconds have played.
Page 222: Theft-Deterrent Feature
Once the disc has scanned, the player defaults to playing MP3 ﬁles in order by artist. The current artist playing is shown on the second line of the display between the arrows. Once all songs by that artist are played, the player moves to the next artist in alphabetical order on the CD-R/CD-RW and begins playing MP3 ﬁles by that artist.
Page 223: Audio Steering Wheel Controls
When the radio and vehicle are turned off, the blinking red light indicates that THEFTLOCK ® With THEFTLOCK activated, the radio does not operate if stolen. Audio Steering Wheel Controls Vehicles with audio steering wheel controls could differ depending on your vehicle’s options.
Page 224: Fixed Mast Antenna
The range for most AM stations is greater than for FM, especially at night. The longer range can cause station frequencies to interfere with each other. For better radio reception, most AM radio stations boost the power levels during the day, and then reduce these levels during the night.
Page 225: Driving Your Vehicle
Section 5 Your Driving, the Road, and the Vehicle ...5-2 Defensive Driving ...5-2 Drunk Driving ...5-2 Control of a Vehicle ...5-3 Braking ...5-3 Antilock Brake System (ABS) ...5-4 Braking in Emergencies ...5-5 ® StabiliTrak System ...5-5 Locking Rear Axle ...5-7 All-Wheel Drive (AWD) System ...5-7 Steering ...5-7 Off-Road Recovery ...5-8...
Page 226: Your Driving, The Road, And The Vehicle
Your Driving, the Road, and the Vehicle Defensive Driving Defensive driving means “always expect the unexpected.” The ﬁrst step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 2-10. WARNING: Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes.
Page 227: Control Of A Vehicle
For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive.
Page 228: Antilock Brake System (Abs)
The brakes might not have time to cool between hard stops. The brakes will wear out much faster with a lot of heavy braking. Keeping pace with the traffic and allowing realistic following distances eliminates a lot of unnecessary braking. That means better braking and longer brake life.
Page 229: Braking In Emergencies
Using ABS Do not pump the brakes. Just hold the brake pedal down ﬁrmly and let antilock work. The brakes might vibrate or some noise might be heard, but this is normal. Braking in Emergencies ABS allows the driver to steer and brake at the same time.
Page 230: Traction Control Operation
For your safety, the system can only be disabled when the vehicle speed is less than 20 mph (32 km/h). Three chimes will be heard and the StabiliTrak light comes on. To turn on the StabiliTrak system, press the StabiliTrak button again.
Page 231: Power Steering
Adding non-dealer/non-retailer accessories can affect the vehicle’s performance. See Accessories and Modiﬁcations on page 6-3 for more information. Locking Rear Axle Vehicles with a locking rear axle can give more traction on snow, mud, ice, sand or gravel. It works like a standard axle most of the time, but when traction is low, this feature will allow the rear wheel with the most traction to move the vehicle.
Page 232: Off-Road Recovery
It is better to remove as much speed as possible from a collision. Then steer around the problem, to the left or right depending on the space available. An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o’clock positions, it can be turned a full 180 degrees very quickly without removing either hand.
Page 233: Passing
Passing Passing another vehicle on a two-lane road can be dangerous. To reduce the risk of danger while passing: • Look down the road, to the sides, and to crossroads for situations that might affect a successful pass. If in doubt, wait. •...
Page 234: Driving At Night
slippery until the vehicle is skidding. Learn to recognize warning clues — such as enough water, ice, or packed snow on the road to make a mirrored surface — and slow down when you have any doubt. Remember: Any Antilock Brake System (ABS) helps avoid only the braking skid.
Page 235: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or ﬂowing water. WARNING: Wet brakes can cause crashes.
Page 236: Before Leaving On A Long Trip
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? •...
Page 237: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on ﬂat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all ﬂuid levels and brakes, tires, cooling system, and transmission.
Page 238: Winter Driving
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 0°C (32°F) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand.
Page 239 WARNING: (Continued) • Check again from time to time to be sure snow does not collect there. • Open a window about 5 cm (two inches) on the side of the vehicle that is away from the wind to bring in fresh air. •...
Page 240: If Your Vehicle Is Stuck In Sand, Mud, Ice, Or Snow
If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow Slowly and cautiously spin the wheels to free the vehicle when stuck in sand, mud, ice, or snow. See Rocking Your Vehicle to Get It Out on page 5-16. If the vehicle has a traction system, it can often help to free a stuck vehicle.
Page 241: Loading The Vehicle
Loading the Vehicle It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-installed options. Two labels on your vehicle show how much weight it was designed to carry, the Tire and Loading Information label and the Certiﬁcation/Tire label.
Page 242 The Tire and Loading Information label also shows the size of the original equipment tires (C) and the recommended cold tire inﬂation pressures (D). For more information on tires and inﬂation see Tires on page 6-55 and Inﬂation - Tire Pressure on page 6-63.
Page 243 Example 1 Item Description Vehicle Capacity Weight for Example 1 = Subtract Occupant Weight 150 lbs (68 kg) × 2 = Available Occupant and Cargo Weight = Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs (317 kg) Example 2 Description Vehicle Capacity...
Page 244 Example 3 Item Description Vehicle Capacity Weight for Example 3 = Subtract Occupant Weight 200 lbs (91 kg) × 5 = Available Cargo Weight = 5-20 Refer to your vehicle’s tire and loading information label for speciﬁc information about your vehicle’s capacity weight and seating positions.
Page 245 This is called Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. The Certiﬁcation/Tire label also tells you the maximum weights for the front and rear axles, called Gross Axle Weight Rating (GAWR). To ﬁnd out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle.
Page 246: Towing
Towing Towing Your Vehicle To avoid damage, the disabled vehicle should be towed with all four wheels off the ground. Consult your dealer/retailer or a professional towing service if the disabled vehicle must be towed. See Roadside Assistance Program on page 8-6. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motorhome, see “Recreational Vehicle Towing”...
Page 247: Dinghy Towing
Dinghy Towing Two-Wheel-Drive Vehicles Notice: If the vehicle is towed with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty. Do not tow the vehicle with all four wheels on the ground.
Page 248: Dolly Towing
All-Wheel-Drive Vehicles The vehicle was not designed to be towed with all four wheels on the ground. To properly tow these vehicles, they should be placed on a platform trailer with all four wheels off the ground. Notice: Towing an all-wheel-drive vehicle with all four wheels on the ground, or even with only two of its wheels on the ground, will damage drivetrain components.
Page 249 Use the following procedure to tow the vehicle from the rear: 1. Attach the dolly to the tow vehicle following the dolly manufacturer’s instructions. 2. Drive the rear wheels onto the dolly. 3. Firmly set the parking brake. See Parking Brake on page 3-35 for more information.
Page 250: Towing A Trailer
Towing a Trailer If the vehicle has a diesel engine, see the DURAMAX Diesel manual for more information. WARNING: The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly. For example, if the trailer is too heavy, the brakes may not work well —...
Page 251: Weight Of The Trailer
Pulling A Trailer Here are some important points: • There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police.
Page 252 Use the following chart to determine how much the vehicle can weigh, based upon the vehicle model and options. Vehicle Axle Ratio G1500 Cargo Van 2WD 4.3L V6 3.42 3.42 5.3L V8 3.73 H1500 Cargo Van AWD 5.3L V8 3.42 G1500 Passenger Van 2WD 5.3L V8 3.73...
Page 253 Vehicle Axle Ratio G3500 Cargo Van 2WD Short Wheelbase 3.73 4.8L V8 4.10 3.73 6.0L V8 4.10 G3500 Cargo Van 2WD Long Wheelbase 3.73 4.8L V8 4.10 3.73 6.0L V8 4.10 G3500 Passenger Van 2WD Short Wheelbase 6.0L V8 3.73 G3500 Passenger Van 2WD Long Wheelbase 6.0L V8 3.73...
Page 254: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
Page 255 Consider the following example: A vehicle model base weight is 5,500 lbs (2 495 kg); 2,800 lbs (1 270 kg) at the front axle and 2,700 lbs (1 225 kg) at the rear axle. It has a GVWR of 7,200 lbs (3 266 kg), a RGAWR of 4,000 lbs (1 814 kg) and a GCWR (Gross Combination Weight Rating) of 14,000 lbs (6 350 kg).
Page 256 Dividing the 900 lbs (408 kg) by 1.5 leaves only 600 lbs (272 kg) of tongue weight that can be handled. Since tongue weight is usually at least 10 percent of total loaded trailer weight, expect that the largest trailer the vehicle can properly handle is 6,000 lbs (2 721 kg).
Page 257: Safety Chains
If the loaded trailer being pulled will weigh more than 5,000 lbs (2 270 kg), be sure to use a properly mounted weight-distributing hitch and sway control of the proper size. This equipment is very important for proper vehicle loading and good handling when driving. Always use a sway control if the trailer will weigh more than these limits.
Page 258: Driving With A Trailer
Tow/Haul is designed to be most effective when the vehicle and trailer combined weight is at least 75 percent of the vehicle’s Gross Combined Weight Rating (GCWR). See “Weight of the Trailer” later in the section. Tow/Haul is most useful under the following driving conditions: •...
Page 259: Making Turns
Towing a trailer requires a certain amount of experience. Get to know the rig before setting out for the open road. Get acquainted with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now longer and not as responsive as the vehicle is by itself.
Page 260: Driving On Grades
Driving On Grades Reduce speed and shift to a lower gear before starting down a long or steep downgrade. If the transmission is not shifted down, the brakes might have to be used so much that they would get hot and no longer work well. The vehicle can tow in D (Drive).
Page 261: Trailer Wiring Harness
Leaving After Parking on a Hill 1. Apply and hold the brake pedal while you: • start the engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks. 4.
Page 262 The seven-wire harness connector contains the following trailer circuits: • Light Green: Back-up Lamps (10A fuse)** • White: Ground • Dark Blue: Trailer Brake Signal • Dark Green: Right Rear Stop and Turn Signal* • Red/Black Stripe: Battery Feed (30A Fuse) •...
Page 263: Service And Appearance Care
Section 6 Service ...6-3 Accessories and Modiﬁcations ...6-3 California Proposition 65 Warning ...6-4 California Perchlorate Materials Requirements ...6-4 Doing Your Own Service Work ...6-4 Adding Equipment to the Outside of the Vehicle ...6-5 Fuel ...6-5 Gasoline Octane ...6-6 Gasoline Speciﬁcations ...6-6 California Fuel ...6-7 Additives ...6-7 Fuel E85 (85% Ethanol) ...6-8...
Page 264 Section 6 Tires ...6-55 Tire Sidewall Labeling ...6-56 Tire Terminology and Deﬁnitions ...6-60 Inﬂation - Tire Pressure ...6-63 Dual Tire Operation ...6-64 Tire Pressure Monitor System ...6-65 Tire Pressure Monitor Operation ...6-66 Tire Inspection and Rotation ...6-69 When It Is Time for New Tires ...6-72 Buying New Tires ...6-73 Different Size Tires and Wheels ...6-74 Uniform Tire Quality Grading ...6-75...
Page 265: Service
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added to the vehicle, they can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like...
Page 266: California Proposition 65 Warning
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many ﬂuids, and some component wear by-products contain and/or emit these chemicals.
Page 267: Adding Equipment To The Outside Of The Vehicle
This vehicle has an airbag system. Before attempting to do your own service work, see Servicing Your Airbag-Equipped Vehicle on page 2-77. Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7-15.
Page 268: Gasoline Octane
The 8th digit of the Vehicle Identiﬁcation Number (VIN) shows the code letter or number that identiﬁes the vehicle’s engine. The VIN is at the top left of the instrument panel. See Vehicle Identiﬁcation Number (VIN) on page 6-103. If the vehicle has the 4.8L V8 engine (VIN Code A), the 5.3L V8 engine (VIN Code 4), or the 6.0L V8 engine (VIN Code G) and the N15 ﬂexible fuel option, you can use either regular unleaded gasoline or ethanol fuel...
Page 269: California Fuel
California Fuel If the vehicle is certiﬁed to meet California Emissions Standards, it is designed to operate on fuels that meet California speciﬁcations. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, the vehicle will operate satisfactorily on fuels meeting federal speciﬁcations, but emission control system performance might be affected.
Page 270: Fuel E85 (85% Ethanol)
Also, your dealer/retailer has additives that will help correct and prevent most deposit-related problems. Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the speciﬁcations described earlier.
Page 271: Fuels In Foreign Countries
At a minimum, E85 should meet ASTM Speciﬁcation D 5798. By deﬁnition, this means that fuel labeled E85 will have an ethanol content between 70% and 85%. Filling the fuel tank with fuel mixtures that do not meet ASTM speciﬁcations can affect driveability and could cause the malfunction indicator lamp to come on.
Page 272: Filling The Tank
Filling the Tank WARNING: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn off the engine when refueling.
Page 273 WARNING: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather.
Page 274: Filling A Portable Fuel Container
Filling a Portable Fuel Container WARNING: Never ﬁll a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs.
Page 275: Hood Release
Hood Release To open the hood: 1. Pull the handle with this symbol on it. It is located in front of the driver’s side door frame near the ﬂoor. 2. Then go to the front of the vehicle and lift up the secondary hood release, which is located underneath the middle of the hood.
Page 276: Engine Compartment Overview
Engine Compartment Overview ® If the vehicle has a diesel engine, see the maintenance schedule section in the DURAMAX Diesel manual. When the hood is lifted: 6-14...
Page 277: Engine Oil
A. Battery. See Battery on page 6-40. B. Radiator Pressure Cap. See Cooling System on page 6-26. C. Coolant Recovery Tank. See Cooling System on page 6-26. D. Automatic Transmission Fluid Dipstick. See “Checking the Fluid Level” under Automatic Transmission Fluid (4-Speed Transmission) on page 6-20 or Automatic Transmission Fluid (6-Speed Transmission) on page 6-23.
Page 278: When To Add Engine Oil
When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 6-110.
Page 279: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Look for three things: • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50.
Page 280: Engine Oil Life System
Engine Oil Additives / Engine Oil Flushes Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all that is needed for good performance and engine protection. Engine oil system ﬂushes are not recommended and could cause engine damage not covered by the vehicle warranty.
Page 281: Engine Air Cleaner/Filter
If the message comes back on when the vehicle is started, the engine oil life system has not reset. Repeat the procedure. If it still does not reset, see your dealer/retailer for service. What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer.
Page 282: Automatic Transmission Fluid (4-Speed Transmission)
When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at the Maintenance II intervals and replace it at the ﬁrst oil change after each 50,000 mile (80 000 km) interval. See Scheduled Maintenance on page 7-3 for more information. If you are driving in dusty/dirty conditions, inspect the ﬁlter at each engine oil change.
Page 283: Transmission)
When to Check and Change Automatic Transmission Fluid A good time to check your automatic transmission ﬂuid level is when the engine oil is changed. Change the ﬂuid and ﬁlter at the intervals listed in Scheduled Maintenance on page 7-3, and be sure to use the transmission ﬂuid listed in Recommended Fluids and Lubricants on page 7-11.
Page 284 Checking the Fluid Level Prepare your vehicle as follows: 1. Park your vehicle on a level place. Keep the engine running. 2. With the parking brake applied, place the shift lever in P (Park). 3. With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range.
Page 285: How To Add Automatic Transmission Fluid
How to Add Automatic Transmission Fluid Refer to the Maintenance Schedule to determine what kind of transmission ﬂuid to use. See Recommended Fluids and Lubricants on page 7-11. Using a funnel, add ﬂuid down the transmission dipstick tube only after checking the transmission ﬂuid while it is hot.
Page 286: Checking The Fluid Level
If it is decided to check the ﬂuid level, be sure to follow all the instructions here, or a false reading on the dipstick may occur. Notice: Too much or too little ﬂuid can damage your transmission. Too much can mean that some of the ﬂuid could come out and fall on hot engine parts or exhaust system parts, starting a ﬁre.
Page 287 3. With foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range. When M is reached, move the selector from M1 through M3. Then, position the shift lever in P (Park). 4.
Page 288: Cooling System
How to Add Automatic Transmission Fluid Refer to the Maintenance Schedule to determine what kind of transmission ﬂuid to use. See Recommended Fluids and Lubricants on page 7-11. A. WARM Range B. HOT Range Using a funnel, add ﬂuid down the transmission dipstick tube only after checking the transmission ﬂuid while it is warm or hot.
Page 289 A. Radiator Pressure Cap B. Coolant Recovery Tank C. Engine Cooling Fan(s) WARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.
Page 290: Engine Coolant
Engine Coolant The cooling system in the vehicle is ﬁlled with ® DEX-COOL engine coolant. This coolant is designed to remain in the vehicle for ﬁve years or 150,000 miles (240 000 km), whichever occurs ﬁrst. The following explains the cooling system and how to check and add coolant when it is low.
Page 291: Checking Coolant
Checking Coolant The vehicle must be on a level surface when checking the coolant level. Check to see if coolant is visible in the coolant recovery tank. If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. If coolant is visible but the coolant level is not at or above the COLD FILL mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL...
Page 292: How To Add Coolant To The Radiator
How to Add Coolant to the Radiator If your vehicle has a diesel engine, see “How to Add Coolant to the Radiator” under “Van Models” in the Cooling System section of the DURAMAX Supplement for the proper radiator ﬁll procedure. WARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and...
Page 293 1. You can remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot. Turn the pressure cap slowly counterclockwise until it ﬁrst stops. Do not press down while turning the pressure cap.
Page 294 4. Then ﬁll the coolant recovery tank to the COLD FILL mark. 5. Put the cap back on the coolant recovery tank, but leave the radiator pressure cap off. 6-32 6. Start the engine and let it run until you can feel the upper radiator hose getting hot.
Page 295: Engine Overheating
Engine Overheating If your vehicle has the DURAMAX Diesel engine, see the DURAMAX Diesel manual for more information. The vehicle has an indicator to warn of engine overheating. You will ﬁnd an engine coolant temperature gage on your vehicle’s instrument panel. See Engine Coolant Temperature Gage on page 4-30 for more information.
Page 296: Engine Fan Noise
If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: •...
Page 297: Power Steering Fluid
You may also hear this fan noise when you start the engine. It will go away as the fan clutch partially disengages. Power Steering Fluid The power steering ﬂuid reservoir is located in the engine compartment on the driver’s side of the vehicle.
Page 298: Windshield Washer Fluid
Windshield Washer Fluid What to Use When you need windshield washer ﬂuid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a ﬂuid that has sufficient protection against freezing.
Page 299: Brakes
Brakes Brake Fluid The brake master cylinder reservoir is ﬁlled with DOT 3 brake ﬂuid. See Engine Compartment Overview on page 6-14 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down: •...
Page 300: Checking Brake Fluid
Checking Brake Fluid Check brake ﬂuid by looking at the brake ﬂuid reservoir. See Engine Compartment Overview on page 6-14. The ﬂuid level should be above MIN. If it is not, have the brake hydraulic system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the level is above the MIN but not over the MAX mark.
Page 301: Brake Wear
Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal ﬁrmly.
Page 302: Battery
Battery Refer to the replacement number on the original battery label when a new battery is needed. See Engine Compartment Overview on page 6-14 for battery location. DANGER: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm.
Page 303: Jump Starting
Jump Starting If the vehicle battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. WARNING: Batteries can hurt you. They can be dangerous because: •...
Page 304 4. Open the hoods and locate the positive (+) and negative (−) terminal locations of the other vehicle. Your vehicle has a remote positive (+) jump starting terminal and a remote negative (−) jump starting terminal. You should always use these remote terminals instead of the terminals on the battery.
Page 305 WARNING: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables do not have loose or missing insulation. If they do, you could get a shock.
Page 306 8. Now connect the black negative (−) cable to the negative (−) terminal of the good battery. Use a remote negative (−) terminal if the vehicle has one. Do not let the other end touch anything until the next step. The other end of the negative (−) cable does not go to the dead battery.
Page 307: All-Wheel Drive
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative (−) cable from the vehicle that had the dead battery. 2. Disconnect the black negative (−) cable from the vehicle with the good battery. 3.
Page 308: Rear Axle
Rear Axle When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant. See Scheduled Maintenance on page 7-3. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
Page 309: Noise Control System
If the level is below the bottom of the ﬁller plug hole, you may need to add some lubricant. When the differential is cold, add enough lubricant to raise the level to 3/8 inch (10 mm) below the ﬁller plug hole. When the differential is at operating temperature (warm), add enough lubricant to raise the level to the bottom of the ﬁller plug hole.
Page 310: Bulb Replacement
2. The use of the vehicle after such device or element of design has been removed or rendered inoperative by any person. Among those acts presumed to constitute tampering are the acts listed below. Insulation: • Removal of the noise shields or any underhood insulation.
Page 311: Halogen Bulbs
Halogen Bulbs WARNING: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package. Headlamps To remove the headlamp assembly from the vehicle and access the bulbs: 1.
Page 312 5. Lift the outboard side of the headlamp to release the outboard tab from the radiator support. 6. Lower the headlamp to allow the vertical adjustor to clear the tie bar. 7. Turn the headlamp forward and upward to remove it from the grille.
Page 313: Front Turn Signal, Sidemarker And Parking Lamps
Front Turn Signal, Sidemarker and Parking Lamps To replace the front turn signal, sidemarker and/or parking lamp bulb(s): 1. Use a small tool to unlatch the outboard clip on the lamp. 2. Pull the lamp forward to completely unlatch the clip.
Page 314: Taillamps
4. Turn the bulb clockwise one quarter turn to install it in the socket. 5. Reinstall the CHMSL assembly and two screws. Do not block or damage the CHMSL when items are loaded on the roof of the vehicle. Taillamps To replace one of these bulbs: 1.
Page 315: License Plate Lamp
11. Slide the taillamp slightly downward to reengage the lower clip. 12. Push the taillamp straight forward to reengage the studs. 13. Reinstall the two inboard nuts from the inside of the taillamp assembly. License Plate Lamp To replace one of these bulbs: A.
Page 316: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear and cracking. See Scheduled Maintenance on page 7-3 for more information on wiper blade inspection. Replacement blades come in different types and are removed in different ways. To remove the type with a release clip, do the following: 1.
Page 317: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. WARNING: Poorly maintained and improperly used tires are dangerous.
Page 318: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into the sidewall. The following illustrations are examples of a typical P-Metric and a LT-Metric tire sidewall. Passenger (P-Metric) Tire (A) Tire Size The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 319 (G) Maximum Cold Inﬂation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load. For information on recommended tire pressure see Inﬂation - Tire Pressure on page 6-63 and Loading the Vehicle on page 5-17. Light Truck (LT-Metric) Tire (A) Tire Size The tire size code is a combination...
Page 320 (F) Tire Ply Material The type of cord and number of plies in the sidewall and under the tread. (G) Single Tire Maximum Load that can be carried and the maximum pressure needed to support that load when used as a single.
Page 321 Light Truck (LT-Metric) Tire (A) Light Truck (LT-Metric) Tire States version of a metric tire sizing system. The letters LT as the ﬁrst two characters in the tire size means a light truck tire engineered to standards set by the U.S. Tire and Rim Association.
Page 322: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Air Pressure The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight This means the combined weight of optional accessories.
Page 323 Intended Outboard Sidewall asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) The metric unit for air pressure. Light Truck (LT-Metric) Tire light duty trucks and some multipurpose passenger vehicles. Load Index An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire.
Page 324 Speed Rating An alphanumeric code assigned to a tire indicating the maximum speed at which a tire can operate. Traction The friction between the tire and the road surface. The amount of grip provided. Tread The portion of a tire that comes into contact with the road.
Page 325: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following: •...
Page 326: Dual Tire Operation
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are underinﬂated. Check the tire’s inﬂation pressure when the tires are cold.
Page 327: Tire Pressure Monitor System
Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your vehicle’s tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inﬂated to the inﬂation pressure recommended by the vehicle manufacturer...
Page 328: Tire Pressure Monitor Operation
Federal Communications Commission (FCC) and Industry and Science Canada See Radio Frequency Statement on page 8-18 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/211 of Industry and Science Canada. Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS).
Page 329: Tpms Malfunction Light And Message
Your vehicle’s TPMS can warn you about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection and Rotation on page 6-69 and Tires on page 6-55. Notice: Liquid tire sealants could damage the Tire Pressure Monitor System (TPMS) sensors.
Page 330: Tpms Sensor Matching Process
TPMS Sensor Matching Process Each TPMS sensor has a unique identiﬁcation code. Any time you rotate your vehicle’s tires or replace one or more of the TPMS sensors, the identiﬁcation codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver...
Page 331: Tire Inspection And Rotation
5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire’s air pressure for ﬁve seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds to sound, conﬁrms that the sensor identiﬁcation code has been matched to this tire and wheel position.
Page 332 Single Rear Wheels If your vehicle has single rear wheels, always use the correct rotation pattern shown here when rotating the vehicle’s tires. Do not include the spare tire in the tire rotation. 6-70 Dual Rear Wheels If the vehicle has dual rear wheels and the tread design for the front tires is the same as the rear tires, always use one of the correct rotation patterns shown here when rotating the tires.
Page 333 If the vehicle has dual rear wheels and the tread design for the front tires is different from the dual rear tires, always use the correct rotation pattern shown here when rotating the tires. The dual tires are rotated as a pair and the inside rear tires become the outside rear tires.
Page 334: When It Is Time For New Tires
When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions, inﬂuence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which appear when your tires have only 1/16 inch (1.6 mm) or...
Page 335: Buying New Tires
Buying New Tires GM has developed and matched speciﬁc tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Speciﬁcation (TPC spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating.
Page 336: Different Size Tires And Wheels
Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC Spec rated tires are installed on your vehicle. Non-TPC Spec rated tires may give a low-pressure warning that is higher or lower than the proper warning level you would get with TPC Spec rated tires.
Page 337: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance.
Page 338: Wheel Alignment And Tire Balance
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 339: Used Replacement Wheels
Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of the wheels, wheel bolts, wheel nuts or Tire Pressure Monitor System (TPMS) sensors, replace them only with new GM original equipment parts.
Page 340: Tire Chains
Tire Chains WARNING: If your vehicle has dual wheels or P245/70R17 or LT245/75R16 size tires, do not use tire chains. They can damage your vehicle because there is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts.
Page 341: If A Tire Goes Flat
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly.
Page 342: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning ﬂashers. See Hazard Warning Flashers on page 4-3. WARNING: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
Page 343: Removing The Spare Tire And Tools
When the vehicle has a ﬂat tire (B), use the following example as a guide to assist you in the placement of wheel blocks (A). A. Wheel Block B. Flat Tire The following information explains how to use the jack and change a tire.
Page 344 To access the equipment, remove the retaining wing bolt and lift it out of the mounting bracket. 6-82 The tools you will be using include the jack (A), jack handle (B), hoist extension (C), jack handle extension (D), and the wheel wrench (E). The spare tire is mounted in the rear underbody of the vehicle.
Page 345 To lower the spare tire from the vehicle: A. Spare Tire E. Hoist Shaft B. Tire/Wheel Retainer F. Jack Handle and Hoist Extensions C. Hoist Cable G. Wheel Wrench D. Hoist Assembly 1. Assemble the wheel wrench (G) to one or two of the jack handle extensions and the hoist extension.
Page 346 3. Turn the wheel wrench counterclockwise to lower the spare tire to the ground. Continue to turn the wheel wrench until the spare tire can be pulled out from under the vehicle. If the spare tire does not lower to the ground, the secondary latch is engaged causing the tire not to lower.
Page 347: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and Installing the Spare Tire If your vehicle has plastic wheel nut caps, loosen them by turning the wheel wrench counterclockwise. The wheel nut caps are designed to remain with the center cap. Remove the center cap. If the wheel has a smooth center piece, place the chisel end of the wheel wrench in the slot on the wheel and gently pry it out.
Page 348 Front Position Front Position 6-86...
Page 349 Rear Position Rear Alternative Position (Diesel Vehicles) 4. Position the jack under the vehicle as shown. The front position jacking point is on the frame. The rear position jacking point is on the rear axle. If the exhaust system interferes in the jack location in the rear axle, such as in Diesel vehicles, place the jack (A) on the rear axle between the axle housing and the shock absorber bracket in order to...
Page 350 WARNING: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. WARNING: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
Page 351 WARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Page 352 10. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely. WARNING: Wheel nuts that are not tight can work loose. If all the nuts on a wheel come off, the wheel can come off the vehicle, causing a crash. All wheel nuts must be properly tightened.
Page 353 WARNING: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque speciﬁcation after replacing. Follow the torque speciﬁcation supplied by the aftermarket manufacturer when using accessory locking wheel nuts.
Page 354: Secondary Latch System
Secondary Latch System Your vehicle has an underbody-mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the spare tire from suddenly falling off the vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stowed with the valve stem pointing down.
Page 355 3. Attach the jack handle/jack handle extension and wheel wrench to the jack. 4. Place the jack under the vehicle, ahead of the rear bumper. Position the center lift point of the jack under the center of the spare tire and turn the handle clockwise to raise the jack until it lifts the secondary latch spring.
Page 356: Storing A Flat Or Spare Tire And Tools
6. Lower the jack by turning the wheel wrench counterclockwise. Keep lowering the jack until the spare tire slides off the jack or is hanging by the cable. 7. Disconnect the jack handle from the jack and carefully remove the jack. Use one hand to push against the spare while ﬁrmly pulling the jack out from under the spare tire with the other hand.
Page 357 2. Pull the retaining bar through the center of the wheel, making sure it is properly attached. 3. Pull the wheel toward the rear of the vehicle, keeping the cable tight. 4. Put the chisel end of the hoist extension on an angle through the hole in the rear door frame, above the bumper.
Page 358: Spare Tire
Spare Tire This vehicle, when new, may have had a fully-inﬂated spare tire. A spare tire may lose air over time, so check its inﬂation pressure regularly. See Inﬂation - Tire Pressure on page 6-63 and Loading the Vehicle on page 5-17 for information regarding proper tire inﬂation and loading the vehicle.
Page 359: Fabric/Carpet
Notice: Using abrasive cleaners when cleaning glass surfaces on the vehicle, could scratch the glass and/or cause damage to the rear window defogger. When cleaning the glass on the vehicle, use only a soft cloth and glass cleaner. Many cleaners contain solvents that may become concentrated in the vehicle’s breathing space.
Page 360: Instrument Panel, Vinyl, And Other Plastic Surfaces
To clean: 1. Saturate a lint-free, clean white cloth with water or club soda. 2. Wring the cloth to remove excess moisture. 3. Start on the outside edge of the soil and gently rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled.
Page 361: Care Of Safety Belts
Care of Safety Belts Keep belts clean and dry. WARNING: Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water. Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak.
Page 362: Cleaning Exterior Lamps/Lenses
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 6-99. Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint ﬁnish.
Page 363: Windshield And Wiper Blades
Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner. Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer ﬂuid or a mild detergent. Wash the windshield thoroughly when cleaning the blades. Bugs, road grime, sap, and a buildup of vehicle wash/wax treatments may cause wiper streaking.
Page 364: Tires
Tires To clean the tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint ﬁnish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
Page 365: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This legal identiﬁer is in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside. The VIN also appears on the Certiﬁcation/Tire and Service Parts labels and certiﬁcates of title and registration.
Page 366: Electrical System
Electrical System Add-On Electrical Equipment Notice: Do not add anything electrical to the vehicle unless you check with your dealer/retailer ﬁrst. Some electrical equipment can damage the vehicle and the damage would not be covered by the vehicle’s warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 367 Mini-Fuse Usage Empty Steering Wheel Sensor Auxiliary Parking Lamps (Cut-Away) Front Park Lamps Trailer Park Lamps Upﬁtter Park Lamps Right Rear Park Lamp Left Rear Park Lamp Outside Rear View Mirror Switch Airbag/AOS Empty Empty Heating, Ventilation and Air Conditioning 2 Heating, Ventilation and Air Conditioning 1 Empty...
Page 368: Engine Compartment Fuse Block
Mini-Fuse Ignition Switch/Discrete Logic Ignition Sensor (PK3) Instrument Panel Cluster Heating, Ventilation and Air Conditioning Control Auxiliary/Trailer Backup Tail Lamps Backup Upﬁtter Courtesy Lamps Front Door Lock Rear Door Lock Cargo Door Unlock Passenger Door Unlock Rear Passenger Door Unlock Driver Door Unlock Empty Empty...
Page 369 Mini Fuse Usage Right Stop/Turn Trailer Spare Spare Fuel System Control Module Ignition Body Control Module 5 Body Control Module 7 Body Control Module 4 Instrument Panel Cluster Trailer Wiring Spare Brake Switch Windshield Washer Horn Transmission Air Conditioning Compressor Engine Control Module Battery Spare Left Stop/Turn Trailer...
Page 370 Mini Fuse Special Equipment Option Airbag Steering Wheel Sensor Engine Control Module Ignition/Glow Plug Module Transmission Control Module Ignition Transmission Control Module Battery Spare Spare Fuel Operated Heater Module Spare Left high Beam Headlamp Right High Beam Headlamp Left Low Beam Headlamp Right Low Beam Headlamp Wiper Canister Vent Solenoid...
Page 371 J-Case Fuse Usage ABS Motor ABS Module Spare Trailer Wiring Fan High Starter Solenoid Engine Control Module/Powertrain Fuel System Control Module Battery Fan Lo Front Blower Relay Usage Run/Crank Spare Fuel Pump Crank Air Conditioning Compressor Fan High Powertrain Fan Clutch (EV) Fan Low Fan Control 6-109...
Page 372: Capacities And Speciﬁcations
Capacities and Speciﬁcations If your vehicle has the DURAMAX Diesel engine, see the DURAMAX Diesel manual for more information. The following approximate capacities are given in metric and English conversions. See Recommended Fluids and Lubricants on page 7-11 for more information. Application Air Conditioning Refrigerant R134a Cooling System without Rear Heat...
Page 373 Application Fuel Tank Cutaway (Optional Tank)* Cutaway (Standard Tank) Passenger and Cargo * 159 inch (4 039 mm) wheelbase or 177 inch (4 496 mm) wheelbase only Transmission Fluid (Pan Removal and Filter Replacement) 4-SPD 4L60-E 6-SPD 6L90 Wheel Nut Torque All capacities are approximate.
Page 374 ✍ NOTES 6-112...
Page 375 Section 7 Maintenance Schedule ...7-2 Introduction ...7-2 Scheduled Maintenance ...7-3 Owner Checks and Services ...7-9 Maintenance Schedule Recommended Fluids and Lubricants ...7-11 Maintenance Replacement Parts ...7-13 Engine Drive Belt Routing ...7-14 Maintenance Record ...7-15...
Page 376: Maintenance Schedule
Maintenance Schedule Introduction This maintenance section applies to vehicles with a gasoline engine. For diesel engine vehicles, see the maintenance schedule section in the DURAMAX Diesel manual. Notice: Maintenance intervals, checks, inspections, recommended ﬂuids, and lubricants are necessary to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty.
Page 377: Scheduled Maintenance
service technicians, uses genuine GM replacement parts, as well as, up to date tools and equipment to ensure fast and accurate diagnostics. The proper replacement parts, ﬂuids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 7-11 and Maintenance Replacement Parts on page 7-13.
Page 378 • Tire inﬂation check. See Inﬂation - Tire Pressure on page 6-63. • Tire wear inspection. See Tire Inspection and Rotation on page 6-69. • Rotate tires. See Tire Inspection and Rotation on page 6-69. • Fluids visual leak check (or every 12 months, whichever occurs ﬁrst).
Page 379: Additional Required Services
• Vehicles with diesel engine or GVWR above 4 536 kg (10,000 lbs) only: Shields inspection for damage or looseness. Adjust or replace as required. This is a Noise Emission Control Service. Applicable to vehicles sold in the United States and recommended for vehicles sold in Canada.
Page 380 First Engine Oil Change After Every 80 000 km/50,000 Miles • Engine air cleaner ﬁlter replacement. See Engine Air Cleaner/Filter on page 6-19. • Automatic transmission ﬂuid change (severe service) for vehicles mainly driven in heavy city traffic in hot weather, in hilly or mountainous terrain, when frequently towing a trailer, or used for taxi, police, or delivery service.
Page 381 First Engine Oil Change After Every 160 000 km/100,000 Miles • Automatic transmission ﬂuid change (normal service). See Automatic Transmission Fluid (4-Speed Transmission) on page 6-20 or Automatic Transmission Fluid (6-Speed Transmission) on page 6-23. • All-wheel drive only: Transfer case ﬂuid change (normal service).
Page 382 Change engine oil and ﬁlter. Reset oil life system. Engine coolant level check. Windshield washer ﬂuid level check. Tire inﬂation pressures check. Tire wear inspection. Rotate tires. Fluids visual leak check. Engine air cleaner ﬁlter inspection (vehicles driven in dusty conditions only). Brake system inspection.
Page 383: Owner Checks And Services
Owner Checks and Services Starter Switch Check WARNING: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. 2.
Page 384: Ignition Transmission Lock Check
Ignition Transmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position. • The ignition should turn to LOCK/OFF only when the shift lever is in P (Park). •...
Page 385: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants This maintenance section applies to vehicles with a gasoline engine. If the vehicle has a diesel engine, see the maintenance schedule section in the DURAMAX Diesel manual. Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer.
Page 386 Usage Fluid/Lubricant SAE 75W-90 Synthetic Axle Lubricant (GM Part Front and No. U.S. 89021677, Rear Axle in Canada 89021678) or equivalent meeting GM Speciﬁcation 9986115. ® DEXRON -VI Automatic Transfer Case Transmission Fluid. One-Piece Propshaft Slip Spline Lubricant, Special Lubricant Yoke Spline, (GM Part No.
Page 387: Maintenance Replacement Parts
Maintenance Replacement Parts If the vehicle has the DURAMAX Diesel engine, see the DURAMAX Diesel manual for more information. Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained by your dealer/retailer. Part Engine Air Cleaner/Filter Engine Oil Filter 4.3L V6 4.8L V8, 5.3L V8, 6.0L V8 Spark Plugs...
Page 388: Engine Drive Belt Routing
Engine Drive Belt Routing V6 Engines 7-14 V8 Engines If your vehicle has the DURAMAX ® the DURAMAX Diesel manual for more information. ® Diesel engine, see...
Page 389: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. Retain all maintenance receipts. Maintenance Record Odometer Date Serviced By Services Performed Reading 7-15...
Page 390 Maintenance Record (cont’d) Odometer Date Serviced By Services Performed Reading 7-16...
Page 391 Maintenance Record (cont’d) Odometer Date Serviced By Services Performed Reading 7-17...
Page 392 Maintenance Record (cont’d) Odometer Date Serviced By Services Performed Reading 7-18...
Page 393: Customer Assistance Information
Section 8 Customer Assistance and Information ...8-2 Customer Satisfaction Procedure ...8-2 Online Owner Center ...8-4 Customer Assistance for Text Telephone (TTY) Users ...8-5 Customer Assistance Offices ...8-5 GM Mobility Reimbursement Program ...8-6 Roadside Assistance Program ...8-6 Scheduling Service Appointments ...8-9 Courtesy Transportation Program ...8-9 Collision Damage Repair ...8-10 Customer Assistance Information...
Page 394: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to GMC. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 395 Although you may be required to resort to this informal dispute resolution program prior to ﬁlling out a court action, use of the program is free of charge and your case will generally be heard within 40 days. If you do not agree with the decision given in your case, you may reject it and proceed with any other venue for relief available to you.
Page 396: Online Owner Center
— all in one convenient place. • Digital owner manual, warranty information, and more • Online service and maintenance records • Find GMC dealers for service nationwide • Exclusive privileges and offers • Recall notices for your speciﬁc vehicle • ®...
Page 397: Customer Assistance For Text Telephone (Tty) Users
Telephone (TTY) Users To assist customers who are deaf, hard of hearing, or speech-impaired and who use the Text Telephones (TTYs), GMC has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with GMC by dialing: 1-800-GMC-8583 (462-8583).
Page 398: Gm Mobility Reimbursement Program
General Motors of Canada also has a Mobility Program. Call 1-800-GM-DRIVE (463-7483) for details. TTY users call 1-800-263-3830. Roadside Assistance Program For U.S. purchased vehicles, call 1-800-GMC-8782 (1-800-462-8782); (Text telephone (TTY): 1-888-889-2438). For Canadian purchased vehicles, call 1-800-268-6800. Service is available 24 hours a day, 365 days a year.
Page 399 • Emergency Tow From a Public Road or Highway: Tow to the nearest GMC dealer for warranty service, or if the vehicle was in a crash and cannot be driven. Assistance is also given when the vehicle is stuck in the sand, mud, or snow.
Page 400 • Trip Routing Service: Detailed maps of North America are provided when requested either with the most direct route or the most scenic route. Additional travel information is also available. Allow three weeks for delivery. • Trip Interruption Beneﬁts and Assistance: If your trip is interrupted due to a warranty failure, incidental expenses may be reimbursed during the 5 years/ 100,000 miles (160 000 km) Powertrain warranty...
Page 401: Scheduling Service Appointments
Scheduling Service Appointments When your vehicle requires warranty service, contact your dealer/retailer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer/retailer can help minimize your inconvenience. If your vehicle cannot be scheduled into the service department immediately, keep driving it until it can be scheduled for service, unless, of course, the problem is safety-related.
Page 402: Collision Damage Repair
Public Transportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, and public transportation is used instead of the dealer’s shuttle service, the expense must be supported by original receipts and can only be up to the maximum amount allowed by GM for shuttle service. In addition, for U.S.
Page 403 Collision Parts Genuine GM Collision parts are new parts made with the same materials and construction methods as the parts with which your vehicle was originally built. Genuine GM Collision parts are your best choice to ensure that your vehicle’s designed appearance, durability, and safety are preserved.
Page 404: If A Crash Occurs
If your vehicle is leased, the leasing company may require you to have insurance that assures repairs with Genuine GM Original Equipment Manufacturer (OEM) parts or Genuine Manufacturer replacement parts. Read your lease carefully, as you may be charged at the end of your lease for poor quality repairs.
Page 405 • If possible, call your insurance company from the scene of the crash. They will walk you through the information they will need. If they ask for a police report, phone or go to the police department headquarters the next day and you can get a copy of the report for a nominal fee.
Page 406: Reporting Safety Defects
Reporting Safety Defects to General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, please notify General Motors. Call 1-800-GMC-8782 (1-800-462-8782), or write: GMC Customer Assistance Center P.O. Box 33172 Detroit, MI 48232-5172 In Canada, call 1-800-263-3777 (English) or...
Page 407: Service Publications Ordering Information
Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle suspension, brakes, electrical, steering, body, etc. Service Bulletins Service Bulletins give additional technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle.
Page 408: Vehicle Data Recording And Privacy
Vehicle Data Recording and Privacy Your GM vehicle has a number of sophisticated computers that record information about the vehicle’s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a crash and, if so equipped, to provide antilock braking to help the driver control the vehicle.
Page 409: Onstar
Important: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) is recorded. However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.
Page 410: Radio Frequency Identiﬁcation (Rfid)
Radio Frequency Identiﬁcation (RFID) RFID technology is used in some vehicles for functions such as tire pressure monitoring and ignition system security, as well as in connection with conveniences such as key fobs for remote door locking/unlocking and starting, and in-vehicle transmitters for garage door openers.
Page 411 Accessories and Modiﬁcations ... 6-3 Accessory Power ... 3-23 Accessory Power Outlets ... 4-14 Additives, Fuel ... 6-7 Add-On Electrical Equipment ... 6-104 Air Cleaner/Filter, Engine ... 6-19 Air Conditioning ... 4-15 Airbag Adding Equipment to Your Airbag-Equipped Vehicle ... 2-78 Airbag System Airbag Off Switch ...
Page 412 Audio System(s) ... 4-62 Automatic Door Lock ... 3-10 Automatic Door Unlock ... 3-10 Automatic Headlamp System ... 4-11 Automatic Transmission Fluid ... 6-20, 6-23 Operation ... 3-26, 3-31 Axle, Rear ... 6-46 Battery ... 6-40 Electric Power Management ... 4-13 Run-Down Protection ...
Page 413 Cargo Door Relocking ... 3-9 CD, MP3 ... 4-72 Center High-Mounted Stoplamp (CHMSL) ... 6-51 Chains, Tire ... 6-78 Charging System Light ... 4-27 Check Engine Lamp ... 4-31 Checking Things Under the Hood ... 6-12 Chemical Paint Spotting ... 6-102 Child Restraints Infants and Young Children ...
Page 414 Damage Repair, Collision ... 8-10 Data Recorders, Event ... 8-16 Daytime Running Lamps (DRL) ... 4-11 Defensive Driving ... 5-2 Delayed Locking ... 3-9 DIC Compass ... 4-43 Disc, MP3 ... 4-72 Doing Your Own Service Work ... 6-4 Dome Lamp Override ... 4-13 Dome Lamps ...
Page 415 E85 Fuel ... 6-8 EDR ... 8-16 Electrical Equipment, Add-On ... 6-104 Electrical System Engine Compartment Fuse Block ... 6-106 Floor Console Fuse Block ... 6-104 Fuses and Circuit Breakers ... 6-104 Headlamp Wiring ... 6-104 Windshield Wiper Fuses ... 6-104 Electronic Immobilizer ®...
Page 416 Flat Tire, Changing ... 6-80 Flat Tire, Storing ... 6-94 Fluid Automatic Transmission ... 6-20, 6-23 Power Steering ... 6-35 Windshield Washer ... 6-36 Front Axle ... 6-46 Fuel ... 6-5 Additives ... 6-7 California Fuel ... 6-7 E85 (85% Ethanol) ... 6-8 Filling a Portable Fuel Container ...
Page 417 Headlamps (cont.) Front Turn Signal, Sidemarker and Parking Lamps ... 6-51 High/Low Beam Changer ... 4-5 On Reminder ... 4-11 Heater ... 4-15 Engine Coolant ... 3-25 Highbeam On Light ... 4-36 Highway Hypnosis ... 5-12 Hill and Mountain Roads ... 5-13 Hood Checking Things Under ...
Page 418 Lighting Entry/Exit ... 4-13 Lights Airbag Off ... 4-24 Airbag Readiness ... 4-23 Antilock Brake System (ABS) Warning ... 4-29 Brake System Warning ... 4-28 Charging System ... 4-27 Cruise Control ... 4-36 Exterior Lamps ... 4-9 Flash-to-Pass ... 4-5 Highbeam On ...
Page 419 Navigation System, Privacy ... 8-17 New Vehicle Break-In ... 3-22 Noise Control System, Tampering ... 6-47 Odometer ... 4-22 Trip ... 4-22 Off-Road Recovery ... 5-8 Engine ... 6-15 Engine Oil Life System ... 6-18 Pressure Gage ... 4-34 Pressure Light ... 4-35 Older Children, Restraints ...
Page 420 Passenger Sensing System ... 2-72 Passing ... 5-9 ® PASS-Key III+ Electronic Immobilizer ... 3-20 ® PASS-Key III+ Electronic Immobilizer Operation ... 3-20 Perchlorate Materials Requirements, California ... 6-4 Power Door Locks ... 3-9 Retained Accessory (RAP) ... 3-23 Seat ... 2-3 Steering Fluid ...
Page 421 Recreational Vehicle Towing ... 5-22 Reimbursement Program, GM Mobility ... 8-6 Remote Keyless Entry (RKE) System ... 3-4 Remote Vehicle Start ... 3-6 Removing the Flat Tire and Installing the Spare Tire ... 6-85 Removing the Spare Tire and Tools ... 6-81 Replacement Bulbs ...
Page 422 Securing a Child Restraint Rear Seat Position ... 2-49 Right Front Seat Position ... 2-52, 2-56 Security Light ... 4-35 Service ... 6-3 Accessories and Modiﬁcations ... 6-3 Adding Equipment to the Outside of the Vehicle ... 6-5 Doing Your Own Work ... 6-4 Engine Soon Lamp ...
Page 423 Taillamps ... 6-52 Tampering with Noise Control System Prohibited ... 6-47 Text Telephone (TTY) Users ... 8-5 Theft-Deterrent Feature ... 4-76 Theft-Deterrent Systems ... 3-20 ® PASS-Key III+ Electronic Immobilizer ... 3-20 ® PASS-Key III+ Electronic Immobilizer Operation ... 3-20 Tilt Wheel ...
Page 424 Uniform Tire Quality Grading ... 6-75 Vehicle Control ... 5-3 Loading ... 5-17 Remote Start ... 3-6 Running While Parked ... 3-39 Symbols ... iv Vehicle Customization, DIC ... 4-52 Vehicle Data Recording and Privacy ... 8-16 Vehicle Identiﬁcation Number (VIN) ... 6-103 Service Parts Identiﬁcation Label ...

This manual is also suitable for:

2010 savanaSavana 2010

GMC 2010 Savana 1500 Cargo Owner's Manual

Section 1 in Brief

In Brief

Instrument Panel

Initial Drive Information

Vehicle Features

Performance and Maintenance

Section 2 Seats and Restraint System

Seats and Restraint System

Head Restraints

Front Seats

Rear Seats

Safety Belts

Child Restraints

Airbag System

Restraint System Check

Section 3 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Storage Areas

Section 4 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 5 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and the Vehicle

Towing

Section 6 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

All-Wheel Drive

Rear Axle

Front Axle

Noise Control System

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for GMC 2010 Savana 1500 Cargo

Summary of Contents for GMC 2010 Savana 1500 Cargo