Page 3: Table Of Contents
Table of Contents Introductory Information ... 1 Safety Restraints ... 7 Starting Your Crown Victoria ... 37 Warning Lights and Gauges ... 47 Instrument Panel Controls ... 87 Steering Column Controls ... 109 Features ... 121 Electronic Sound Systems ... 149 Driving Your Crown Victoria ...
Page 4: Introductory Information
Introductory Information Ford’s Commitment to You Our Guiding Principles Quality comes first. For your satisfaction, the quality of our products and services must be our number one priority. You are the focus of everything we do. Our work must be done with you in mind, providing better products and services than our competition.
Page 5 This guide describes equipment and gives specifications for equipment that was in effect when this guide was approved for printing. Ford may discontinue models or change specifications or design without any notice and without incurring obligation.
Page 6 Canadian Owners — French Version French Owner Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3.
Page 7 Buying a Ford Extended Service Plan If you bought your vehicle in the U.S., you can buy a Ford Extended Service Plan for your vehicle. This optional contract provides service protection for a longer period of time than the basic warranty that comes with your vehicle.
Page 8 Use only the type of engine oil that Ford recommends. See Engine oil recommendations in the Index. Do not use special “break-in” oils. Your vehicle is equipped with an Electronic Powertrain Control Module that limits engine and/or vehicle speeds with a cut-out mode to promote durability.
Page 9 Washing and Polishing Your Vehicle Wash the outside of your vehicle, including the underside, with a mild detergent. DO NOT: Wash your vehicle with hot water Wash your vehicle while it sits in direct sunlight Wash your vehicle while the body is hot Polish your vehicle to remove harmful deposits and protect the finish.
Page 10: Safety Restraints
Safety Restraints Important Safety Belt Information The use of safety belts helps to restrain you and your passengers in case of a collision. In most states and in Canada the law requires their use. Safety belts provide best restraint when: the seatback is upright the occupant is sitting upright (not slouched) the lap belt is snug and low on the hips...
Page 11 RWARNING Never wear the shoulder belt under the arm. Never swing it around the neck over the inside shoulder. Never use a single belt for more than one person or across more than one seating position. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair.
Page 12: Combination Lap And Shoulder Belts
Combination Lap and Shoulder Belts While your vehicle is in motion, the combination lap and shoulder belt adjusts to your movement. However, if you brake hard, corner hard or if your vehicle receives an impact of 5 mph (8 km/h) or more, the lap and shoulder belt locks and helps reduce your forward movement.
Page 13 Fastening the rear seat combination lap and shoulder belt NOTE: Be sure to read and understand Important Safety Belt Information at the beginning of this chapter. Safety Belts for All Passenger Outboard Seating Positions Your vehicle is equipped with a dual locking mode retractor on the shoulder belt portion of the combination lap/shoulder safety belt for the front and rear outboard passenger seats.
Page 14 Automatic locking mode In this operating mode, the shoulder belt retractor will be automatically locked and remain locked when the combination lap/shoulder safety belt is buckled, and does not allow the occupant freedom of movement. This mode provides the following: A tight lap/shoulder belt fit on the occupant.
Page 15 NOTE: When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch back to the vehicle sensitive (emergency) locking mode. See the detailed instructions under Safety Seats for Children in this chapter. Shoulder Belt Height Adjustment Driver and right front passenger You can adjust the shoulder belt height to one of five (5) positions.
Page 16 The shoulder belt height adjuster The shoulder belt height adjuster RWARNING The lap belts should fit snugly and as low as possible around the hips, not around the waist.
Page 17 RWARNING All front and rear seat outboard occupants (including pregnant women) should wear lap and shoulder belts, for optimum protection in a collision. RWARNING Failure to follow these precautions could increase the risk and/or severity of injury in a collision. 1) Use the shoulder belt on the outside shoulder only.
Page 18 Lap Belts — Center Seating Position The lap belts in the center of the front and rear seats do not adjust automatically. You must adjust them to fit snugly and as low as possible around your hips. Do not wear them around your waist.
Page 19: Safety Belt Maintenance
(slide bar) (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after any collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision...
Page 20 during a collision should also be inspected and replaced if either damage or improper operation is noted. Cleaning the Safety Belts Clean the safety belts with any mild soap solution that is recommended for cleaning upholstery or carpets. Do not bleach or dye the belt webbing because this may weaken it.
Page 21 There are four very important reasons to use safety belts even with an air bag system. Use your safety belts to: help keep you in the proper position (away from the air bag) when it inflates reduce the risk of harm in rollover, side or rear impact collisions, because an air bag is not designed to inflate in such situations reduce the risk of harm in frontal collisions...
Page 22 In rear-facing infant seats, the infant’s head is closer to the air bag. The force of the rapidly inflating air bag could push the top of the rear-facing seat against the vehicle seatback, center console (if so equipped), or center armrests (if so equipped).
Page 23 Children. For further information about the proper mounting of equipment in the front seat of this vehicle, please refer to Ford’s brochure entitled Some Important Information About Air Bag Supplemental Restraint System which can be obtained by calling Helm Inc. at 1-800-782-4356.
Page 24 The location of the air bag and warning labels If a collision occurs, the sensors sense the severity of the impact and activates the air bags if necessary. The air bag system is designed to deploy in frontal and front-angled collisions more severe than hitting a parked vehicle (of similar size and weight) head-on at about 28 mph (45 km/h).
Page 25 RWARNING Air bag system components get hot after inflation. Do not touch them after inflation. Inflated driver side air bag...
Page 26 Inflated right front passenger side air bag RWARNING If the air bag is inflated, THE AIR BAG WILL NOT FUNCTION AGAIN AND MUST BE REPLACED IMMEDIATELY. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 27: Safety Restraints For Children
If any of these things happen, have the air bag system serviced at your Ford or Lincoln-Mercury dealer immediately. Unless serviced, the air bag supplemental restraint system may not function properly in the event of a collision.
Page 28 RWARNING Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. RWARNING Passengers should not be allowed to ride in the cargo area. Persons not riding in a seat with a fastened seat belt are much more likely to suffer serious injury in a collision.
Page 29 Always follow the safety seat manufacturer’s instructions when installing and using the safety seat. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 30 Children weighing less than 40 lbs. (18 kg) should use child or infant seats. Forward facing child seats must have the passenger seat moved as far back from the instrument panel as possible. RWARNING REAR-FACING INFANT SEATS SHOULD NEVER BE USED IN THE FRONT SEAT. REAR-FACING INFANT SEATS MUST ALWAYS BE PLACED IN THE REAR SEAT.
Page 31 Installing Safety Seats in the Front and Rear Outboard Passenger Seating Positions For seating positions equipped with a dual locking mode retractor, use the following procedure. If you choose to install a child safety seat or infant carrier in the front seating positions, move vehicle seat as far back as possible.
Page 32 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. See Figure 2. Be sure that the belt webbing is not twisted. Routing the lap/shoulder belt...
Page 33 4. Insert the belt tongue into the buckle for that seating position until you hear and feel the latch engage. Figure 3. Make sure tongue is latched securely to buckle by pulling on tongue. Buckling the belt...
Page 34 5. Grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. At this time, the retractor is in the automatic locking mode (child seat restraint mode). Figure 4. NOTE: The dual-locking mode retractor must be in the automatic locking mode to properly restrain a child.
Page 36 7. Before placing the child in the child seat, forcibly tilt the seat from side to side, and tug it forward to make sure that the seat is securely held in place, Figure 7. Checking that the seat is secure 8.
Page 37 Checking the retractor 9. Check to make sure that the child seat is properly secured prior to each use. If the retractor is not locked, repeat steps 4 through 7. Installing a Child Safety Seat at the Rear Center Seating Position with Adjustable Lap Belt 1.
Page 38 4. Insert the belt tongue into the proper buckle for the center seating position until you hear a snap and feel it latch. Make sure the tongue is securely fastened to the buckle by pulling on tongue. 5. Push down on the child seat while pulling on the loose end of the lap belt webbing to tighten the belt.
Page 39 To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards.
Page 40: Warning Lights And Gauges
Warning Lights and Gauges The instrument panel (dashboard) on your vehicle is divided into several different sections. The illustrations on the following pages show the major parts of the instrument panel that are described in this chapter. Some items shown may not be on all vehicles.
Page 42 The Mechanical Cluster The following warning lights and gauges are on the mechanical cluster. All of the warning lights and gauges alert you to possible problems with your vehicle. Some of the lights listed are optional. The following sections detail what each of these indicators means.
Page 43 Anti-Lock Brake System Light (If equipped) This warning light will go on each time you start your vehicle. If it remains on for longer than five seconds, you should shut off your engine and restart. If the anti-lock brake light stays on, this indicates that the anti-lock feature is disabled and should receive immediate attention by a qualified service technician.
Page 44 RWARNING If the anti-lock brake system warning light remains on or comes on while driving, have the braking system checked by a qualified service technician as soon as possible. NOTE: If a fault occurs in the anti-lock system, and the brake warning light is not lit, the anti-lock system is disabled but normal brake function remains operational.
Page 45 If either of these things happen, have the air bag system serviced at your Ford or Lincoln-Mercury dealer immediately. Charging System Light...
Page 46 If the light stays on or comes on when the engine is running, have the electrical system checked as soon as possible. Overdrive Off Indicator This light tells you that the Transmission Control Switch (TCS) on the gearshift lever has been pushed.
Page 47 High Beam Light This light comes on when the headlamps are turned to high beam or when you flash the lights. Low Fuel Alert Light This light comes on when your fuel gauge indicates between 1/8 and 1/16 of a tank. Your car must be turned to ON for this light to come...
Page 48 Air Suspension Light (If equipped) This light tells you if the air suspension needs repair or if the air suspension switch (in the trunk on the right side) is OFF. Normally, the light will glow momentarily as you turn the ignition key to the ON position. If it glows continuously: 1.
Page 49 installed. Do not install these devices by tapping into or running wires close to powertrain control system wires or components. The light comes on briefly when you turn the ignition key to ON, but it should turn off when the engine starts. If the light does not come on when you turn the ignition to ON or if it comes on and stays on when you are driving, have your vehicle serviced as soon as possible.
Page 50 Engine Warning Light will turn off after the vehicle has completed three consecutive warm up cycles without a misfire condition occurring. A warm up cycle consists of engine start from a cold condition (engine at ambient temperature) and running until the engine reaches normal operating temperature.
Page 51 Fuel Gauge The fuel gauge The fuel gauge displays approximately how much fuel is in the fuel tank only when the ignition switch is ON. For proper fuel gauge indication after adding fuel, turn the ignition switch OFF while refueling the vehicle. The fuel gauge indicator may vary slightly when the vehicle is in motion.
Page 52 conditions, and under certain driving conditions such as, heavy stop and go traffic, or driving up hills in hot weather, for the pointer to indicate at the top of the NORMAL band. If, under any circumstances, the pointer moves above the NORMAL band, the engine is overheating and continued operation may cause engine damage.
Page 53 Speedometer The speedometer tells you how many miles (kilometers) per hour your vehicle is moving. Odometer The odometer tells you the total number of miles (kilometers) your vehicle has been driven. Trip Odometer If you want to track your mileage up to 999.9 miles (kilometers), use the trip odometer.
Page 54 The battery voltage gauge Engine Oil Pressure Gauge This gauge indicates the engine oil pressure, not the oil level. However, if your engine’s oil level is low, it could affect the oil pressure. With the engine running, the pointer should move into the NORMAL band.
Page 55 For more information about adding oil, see Engine Oil Recommendations in the Index. The Electronic Cluster The electronic cluster works only when your ignition is in the ON position. Each time you start your vehicle, the displays go through a self-test by flashing on and off once before the actual readings are displayed.
Page 57 Engine Coolant Temperature Gauge This gauge indicates the engine coolant temperature not the coolant level. If the coolant is not at its proper level or mixture, the gauge indication will not be accurate. It is identified by a thermometer symbol, an “H” (hot), and a “C” (cold).
Page 58 3. Let the engine cool. DO NOT REMOVE COOLANT SYSTEM FILL CAP UNTIL THE ENGINE IS COOL. 4. Check the coolant level following the instructions on checking and adding coolant to your engine, see Engine Coolant in the Index. If you do not follow these instructions, you or others could be injured.
Page 59 High Beam Light This light comes on when the headlamps are turned to high beam or when you flash the lights. Check Engine Warning Light The Powertrain On-Board Diagnostic II (OBD II) system consists of the hardware and software necessary to monitor the operation of the powertrain.
Page 60 The light comes on briefly when you turn the ignition key to ON, but it should turn off when the engine starts. If the light does not come on when you turn the ignition to ON or if it comes on and stays on when you are driving, have your vehicle serviced as soon as possible.
Page 61 Under certain conditions, the Check Engine Warning Light may come on if the fuel cap is not properly installed. If the Check Engine Warning Light comes on and you suspect that the fuel cap is not properly installed, pull off the road as soon as it is safely possible and turn off the engine.
Page 62 Charging System Warning Light This light comes on when you turn your ignition key from OFF to ON. The light should go out when the engine starts and the alternator begins to charge. If this light stays on or comes on while your engine is running, this tells you that your battery is not being charged and that you need to have the electrical system checked as soon as...
Page 63 If you lose engine oil pressure: 1. Pull off the road as soon as safely possible. 2. Shut off the engine immediately. If you do not stop the engine as soon as safely possible, severe engine damage could result. 3. Check the engine’s oil level, following the instructions on checking and adding engine oil, see Engine Oil in the Index.
Page 64 Speed Control Indicator Light This light comes on when the speed control system is actively maintaining the set speed. It will go off when the brakes are used or if the speed control is turned off. This light does not indicate any problems but is only a convenience to tell when the speed control is active.
Page 65 NOTE: At least 2.5 gallons (9.5 liters) of fuel must be added for the fuel gauge to immediately show the new level of fuel. If less than 2.5 gallons (9.5 liters) of fuel is added, the gauge will reach the new level slowly. If the fuel gauge displays only the top two bars and the bottom two bars, or, if fuel remaining or distance to empty functions display CO or CS,...
Page 66 A problem is indicated if the fuel gauge bar graph displays only the top two and bottom two bars and the message center display for Distance To Empty or Fuel Remaining functions display the letters “CO” or “CS”. If this happens, contact your dealer for service as soon as possible.
Page 67 Press the E/M (English/Metric) button located just below the message center display to show miles or kilometers. If the odometer displays the word “ERROR” contact your dealer for service. The Electronic Message Center (If equipped) Along with information the warning lights and gauges provide, the electronic message center lets you: see problems such as Door Ajar, Air...
Page 68 All of the message center functions are controlled by the three switches located just below the message center display: E/M — Changes the electronic instrument cluster display to read in either English or Metric units. Reset — Sets the selected function to zero (if resettable).
Page 69 What the message center functions can show you DIST TO EMPTY — Distance to Empty (DTE) Message center display showing the DTE function selected This function estimates how many miles or kilometers you can drive with the fuel remaining in your tank under standard driving conditions. Remember to turn off the ignition when filling up with fuel.
Page 70 Displayed DTE will not be equal to AVG ECON multiplied by the FUEL REMAIN value. This is because DTE is calculated using a method that takes into consideration the fuel economy of the last 500 miles (800 Km) driven. If “CO” or “CS” is displayed, this means that there is a problem with the fuel indication system and you should contact your dealer for service as soon as possible.
Page 71 If you calculate your average fuel economy by dividing miles traveled by gallons used, your figure may be different than displayed because Your vehicle not being perfectly level during fill-up Differences in the automatic shut-off points on the fuel pumps at service stations Variations in top-off procedure from one fill-up to another Rounding of the displayed values to the...
Page 72 TRIP A and TRIP B — Elapsed Distance Traveled These two functions of the message center allow you to see how far you have traveled since you last reset. Trip A and Trip B are completely independent and must be reset individually. To reset either trip feature to zero, press the RESET button while a trip distance feature (Trip A or Trip B) is displayed.
Page 73 Check Air Suspension Light This light glows momentarily when the ignition is turned to the ON position. With the ignition on this light will flash five (5) times and sound a tone for one (1) second, and then the light will remain on to indicate that the air suspension switch (located in the trunk on the right side) is off or to indicate a possible system fault.
Page 74 Overdrive Off Indicator This light tells you that the Transmission Control Switch (TCS) on the gearshift lever has been pushed. When the light is on, the transmission will not shift into overdrive. Depressing the button on the shifter will return the vehicle to “overdrive on”...
Page 75 Door Ajar Light If one of the doors is not completely shut, this light comes on when you turn the ignition to ON. With the ignition on this light will flash five (5) times and sound a tone for one (1) second, and then the light will remain on.
Page 76 Indicator Lamp Module The following warning lights are on the indicator lamp module. The following section details what each of these indicators mean. The indicator lamp module Anti-Theft System Light (If equipped) The anti-theft system light illuminates to remind you that the anti-theft system has been activated. The indicator light remains on steadily for approximately 30 seconds after the last door is closed, and then goes out.
Page 77 Anti-Lock Brake System Light (If equipped) This warning light will go on each time you start your vehicle. If it remains on for longer than 5 seconds, you should shut off your engine and restart. If the anti-lock brake light stays on, this indicates that the anti-lock feature is disabled and should receive immediate attention by a qualified service technician.
Page 78 RWARNING If the anti-lock brake system warning light remains on or comes on while driving, have the braking system checked by a qualified service technician as soon as possible. NOTE: If a fault occurs in the anti-lock system, and the brake warning light is not lit, the anti-lock system is disabled but normal brake function remains operational.
Page 79: Steering Column Controls
RWARNING The BRAKE light indicates that the brakes may not be working properly. Have the brakes checked immediately. Hazard Warning Light The hazard warning light will blink on and off continuously when you use the hazard flasher. See Using the Hazard Flasher in the Steering Column Controls section.
Page 81 The main controls for the climate control system, clock, and radio are on the instrument panel. NOTE: Any cleaner or polish that increases the gloss (shine) of the upper part of the instrument panel should be avoided. The dull finish in this area is to help protect the driver from undesirable windshield reflection.
Page 82 The controls for the manual heating and air conditioning system For maximum heating, move the SELECT knob to FLOOR, move the TEMP knob to the end of the red range (full clockwise) and move the fan speed to HI. To heat the interior of your vehicle and defrost the windshield at the same time, move the SELECT knob to MIX and select the temperature and fan speed desired.
Page 83 If the inside of the vehicle is very warm, drive for the first few minutes with the windows open to force the hot, stale air out of the vehicle. Fan speed can be reduced, after a comfortable temperature has been reached, to provide quieter system operation.
Page 84 the automatic operation with manual override buttons. The controls for the electronic automatic temperature control To turn your EATC on, push the AUTOMATIC button or any of the six override buttons along the bottom of the control. To turn your EATC off, press the OFF button. When the system is off, the display window will be blank (dark) except when OUTSIDE TEMP has been selected.
Page 85 To change the temperature in the display window, select any temperature between 65˚F (18˚C) and 85˚F (29˚C) using the BLUE (cooler) or RED (warmer) buttons. The Electronic Automatic Temperature Control will do the rest. If you want continuous maximum cooling, push the BLUE button until 60˚F (16˚C) is shown in the display window.
Page 86 Automatic operation Push the AUTOMATIC button and select the desired temperature. The selected temperature and AUTO will be shown in the display window. The EATC will automatically heat or cool to achieve the set temperature. Under normal conditions, your EATC will need no additional attention.
Page 87 Temperature selection The RED and BLUE buttons at the upper left of the Control are for temperature selection. The RED button will increase the set temperature and the BLUE button will lower the set temperature. Pressing a button and releasing it will change the set temperature one degree.
Page 88 Temperature display The selected temperature displayed in the window can be set for either 0˚F or 0˚C. Your car may have an English/Metric (E/M) Button to change your speedometer from miles to kilometers. When pressed, this button also changes the temperature display. With or without an E/M Button, the temperature display can also be changed to 0˚F or 0˚C using the MAX A/C and DEFrost override buttons.
Page 89 Fan speed and thumbwheel Your EATC automatically adjusts the fan speed to the existing conditions. You must push AUTOMATIC for automatic fan speed operation. To control the fan speed yourself, use the thumbwheel which will cancel the automatic fan speed control. The thumbwheel is located at the extreme right side of the EATC control panel.
Page 90 You can override the fan speed at any time. If you use the thumbwheel to override the fan speed, the EATC will continue to control the temperature but you control the fan speed. To return to auto fan control, press the AUTOMATIC button.
Page 91 NORM A/C button When you push this button, you select air conditioning using outside air. The Display window will indicate A/C under the selected temperature. The cooled air will flow from the instrument panel registers. The fan speed will continue on automatic. VENT button Push this button to select outside air through the instrument panel registers.
Page 92 DEF V button Press the DEF V button to obtain maximum airflow to the windshield. Adjust the temperature setting as required for defrosting. The Display window will show the temperature setting with the defrost symbol V to the left of the temperature.
Page 93 If the EATC is turned OFF while the outside temperature is displayed, the temperature will continue to be displayed. Press the OUTSIDE TEMP button to clear the display window. When the ignition key is turned OFF the display will be blank (dark). NOTE: The outside temperature reading is most accurate when the vehicle is moving.
Page 94: Instrument Panel Controls
Service If your EATC is not operating as described here, take it to your dealer to have it checked. System diagnostics are built in which will allow your dealer to readily identify problems that might occur. Rear Window Defroster The defroster for the rear window clears frost, fog, or thin ice from both the inside and outside of the rear window.
Page 95: The Interior And Exterior Lights
The heating elements are bonded to the inside of the rear window. Do not use sharp objects to scrape the inside of the rear window or use abrasive cleaners to clean it. Doing so could damage the heating elements. The Interior and Exterior Lights Daytime Running Light System (Canadian vehicles only) The Daytime Running Light (DRL) system turns...
Page 96 Turning On the Exterior Lights To turn on the headlamps, parking lamps, side markers, and tail lamps, use the rotary knob that is to the left of the steering wheel. The knob that controls the headlamps and parking lamps When you turn on the headlamps, the parking lamps, tail lamps, and side markers automatically turn on.
Page 97 Setting the Autolamp On/Off Delay System The autolamp sets the headlamps to turn on and off automatically. You can use the autolamp to: turn on the lamps automatically at night turn off the lamps automatically during daylight keep the lamps on for up to three minutes after you turn the key to OFF.
Page 98 You can adjust the autolamp to keep the lamps on after you leave your vehicle. The further you move the headlamp knob to the left (counterclockwise), the longer the lamps stay on. You can set the autolamp so the lamps stay on for up to three minutes after you turn your vehicle off.
Page 99 Occasionally, you will need to clean the lens of the door lock assembly. Use Ford Multi-Purpose Cleaner Concentrate, a mild soap, or household ammonia and water solution.
Page 100 Turning on the Map and Reading Lamps Your vehicle has two map lamps for the passenger and the driver. To turn on the map lamps, push the switch next to each lamp. Front seat map and dome lamps The dual beam map lamps are located on each side of the dome lamp.
Page 101 Cleaning the Instrument Panel Lens Clean the instrument panel lens with a soft cloth and a glass cleaner, such as Ford Ultra-Clear Spray Glass Cleaner, or equivalent. Do not use paper towel or any abrasive cleaner to clean the...
Page 102: Steering Column Controls
Steering Column Controls The controls on the steering column and wheel are designed to give you easy access to the controls while you are driving. The Turn Signal Lever You can use the turn signal lever on the left side of the steering column to: operate the turn signals turn the high beams on/off...
Page 103 Turn Signals Move the lever up to signal a right turn. Move it down to signal a left turn. The corresponding indicator light in the instrument cluster will flash. If the turn signal stays on after you turn, move the lever back to the center (off) position. For lane changes, move the lever far enough to signal but not to latch.
Page 104: Windshield Wipers And Washer
Windshield Wipers and Washer To turn on the windshield wipers, the ignition key must be turned to the ON or ACC position. Rotate the end of the lever away from you to activate the wipers. The first seven detents are interval wipe positions, the eighth detent is the LO position and the ninth detent is the HI position.
Page 105 If the washer does not work, check the washer fluid level and fill it if it is low. See the Servicing Your Crown Victoria chapter. If there is enough fluid, consult your nearest Ford or Lincoln-Mercury dealer. Do not try to clean the windshield when the...
Page 106 Hazard Flasher To alert other drivers to hazardous situations, push in the hazard flasher on the top of the steering column. The same switch turns the flashers off. The flashers work whether your vehicle is running or not. The flashers work for up to two hours when the battery is fully charged and in good condition without draining the battery excessively.
Page 107 Horn To sound the horn, push the center pad area of the steering wheel. The horn on the steering wheel...
Page 108: Tilt Steering
Tilt Steering RWARNING Never adjust the steering wheel when the vehicle is moving. The lever to tilt the steering wheel To change the position of the steering wheel, pull the release lever on the column toward you. Tip the steering wheel to the desired position. Release the lever to lock the steering wheel in place.
Page 109 Speed Control (If equipped) If your vehicle has speed control, you can automatically maintain a constant speed at or above 30 mph (50 km/h). Use of radio transmitting equipment that is not Federal Communications Commission (FCC) or in Canada the Canadian Radio and Telecommunications Commission (CRTC) approved may cause the speed control to malfunction.
Page 110 The speed control switches on the steering wheel To set the speed control: 1. Press and release the ON switch. 2. Accelerate to the desired speed above 30 mph (50 km/h) using the accelerator pedal. 3. Press the SET ACCEL switch and release it immediately to set your speed.
Page 111 NOTE: If your speed increases above your set speed while driving in D (Drive) on a downhill grade, you may want to depress the Transmission Control Switch located on the shift lever to turn off overdrive to reduce vehicle speed. Speed control cannot reduce the vehicle speed if it goes above your set speed on a downhill grade.
Page 112 TAP-DOWN — Press and then quickly release the COAST switch. Each time you “tap” the switch, the set speed will decrease by one (1) mph (1.6 km/h). Multiple taps will cause the set speed to decrease in increments of one (1) mph (1.6 km/h). For example, if the current set speed is 60 mph (96 km/h) five (5) taps of the COAST switch will decrease the vehicle speed and SET it at...
Page 113 Cancelling and Resuming a Set Speed If you press the brake pedal, speed control is suspended. You can return to the set speed by pressing the RESUME switch, as long as you did not press the OFF switch. You must be driving at least 30 mph (48 km/h).
Page 114: Features
Features Your vehicle has a variety of features designed for your comfort, convenience and safety. Read this chapter to find out about standard and optional features. Doors Childproof Locks for the Rear Doors In addition to power locks, your vehicle has childproof locks for the rear doors.
Page 115 To set the childproof lock on each rear door, open the rear door. Find the lever inside the label with the word LOCKED. Move the lever up. To release the childproof lock, open the rear door from the outside. Move the lever down. Power Door Locks (If equipped) If your vehicle has power door locks, the controls to lock the doors are on the trim panel...
Page 116 Using the Illuminated Entry System (If equipped) The interior lights will illuminate for approximately 25 seconds when either front door handle is lifted, any button on the keyless entry pad is pressed, or the remote entry system UNLOCK button is pushed. If the amount of light outside your vehicle is below a predetermined level, the exterior lights will also illuminate.
Page 117 When you bought your vehicle, you were given a computer code that operates the system for your vehicle. For your convenience, we have duplicated this code in three places. The code is: on your owner’s wallet card found in the glove compartment taped to the underside of the trunk lid taped to the computer module behind the...
Page 118 3. To unlock the trunk, press the 5/6 button within five seconds of unlocking the driver’s or passenger’s doors, or re-enter the code to open the driver’s door, then press 5/6. As long as the driver’s door has been unlocked first, you can open the passenger’s doors or the trunk in any order.
Page 119 If you do not want to use the Autolock feature, it can be deactivated by using the buttons for the keyless entry system. To deactivate the Autolock feature: 1. Enter your permanent five-digit entry code (not the user code you may have set). 2.
Page 120 5. Five seconds after you press the fifth digit, your door lock system will lock and unlock the vehicle doors to confirm successful programming. The keyless entry system registers this second code. To open your vehicle, you can now use either code. The module remembers only one personal code at a time.
Page 121: Remote Entry System
Battery Saver When the ignition is turned off, the vehicle will turn off battery voltage to the vehicle lamps as follows: Courtesy lights (lights which come on when a door is opened): after 10 minutes. Map/Glove compartment/Trunk/Hood lamps: after 30 minutes. Headlamps/Park lamps (only if headlamp switch is left in Headlamp position): after 10 minutes.
Page 122 Remote entry transmitter Unlocking the doors and opening the trunk To unlock the driver’s door, press the UNLOCK button. To unlock the other doors, press the UNLOCK button a second time within five seconds of unlocking the driver’s door. To open the trunk, press the TRUNK button twice within five seconds.
Page 123 Replacement batteries can be purchased at most pharmacies, watch stores or at your Ford or Lincoln-Mercury dealer. NOTE: The operating range of the remote entry system can also be affected by...
Page 124 Replacement/additional transmitters In the event a transmitter is lost, a new one may be purchased from your dealer. To program replacement or additional transmitters you must have all the transmitters intended for use on your vehicle. Initiating the following procedure erases all prior programmed transmitters, thus ALL must be reprogrammed at the same time.
Page 125 NOTE: All transmitters to be used on your vehicle must be programmed/ reprogrammed at the same time. Windows Using the Power Windows Each door has a power control that opens and closes the window on that door. The driver’s door has a master control panel that operates all four windows.
Page 126 There is also an Express Down feature on the driver’s power window. To operate, actuate driver’s power window switch to the down position for less than 0.4 seconds; the window will then open automatically. To terminate automatic operation before the window completely opens, operate the switch again, for less than 0.4 seconds, to either the up or down position.
Page 127 Adjusting the Front Passenger Seat Manually In the front seats, you can move the whole seat forward or backward or tilt the back of the seat forward or backward. To move the seat forward or backward: 1. Find the adjustment bar underneath the front part of the seat.
Page 128 To recline the front seat: 1. On the side of the seat, find the handle for the recliner. 2. Lift the handle up and hold it in place. 3. Lean against the back of the seat and adjust it to the position you want. You can tilt the seat back or bring it forward.
Page 129 Using the Power Seats (If equipped) If your vehicle has power seats, you can adjust them in several directions. The controls are located on the driver and passenger door trim panels or on the side of the driver’s seat. The power seat controls on the driver’s seat — Base models The power seat controls on the driver’s door trim panel RWARNING Do not pile cargo higher than the...
Page 130 Power Seat Recliner/Lumbar Option The arrows on the power seat control panel indicate the direction the seat or seatback will move. To adjust the seat or seatback move the control knob in the desired direction. The power lumbar switch controls the inflation of the lumbar support pad in the seatback.
Page 131 Programmable Memory — Seat and Mirrors (If equipped) If your vehicle is equipped with this option, you can store settings for three seat and mirror positions. This allows you to get into your vehicle and simply push the preset button(s) to automatically have your seat and mirrors in the proper position.
Page 132 To prevent accidental seat movement, this system will only recall a position when the transmission gearshift lever is in P (Park) or N (Neutral) with the engine either running or off. However, a new position can be set at any time.
Page 133 Mirrors You can adjust your rearview mirror in any direction. The special swivel bracket lets you move the mirror up or down and from side to side. RWARNING Make sure you can see clearly through the rearview mirror at all times. Do not block your vision.
Page 134 To turn the mirror on, push the ON/OFF switch, located on the bottom of the mirror, to latch it in the ON position. The switch will illuminate and the mirror will be in the automatic dimming mode. To turn the switch illumination and automatic dimming feature off, push the ON/OFF switch again.
Page 135 The mirror controls on the driver’s left armrest To adjust the side mirrors: 1. Find the control switch in the driver’s door panel. 2. Select the right or left mirror by moving the selector switch to R or L. 3. Move the knob in the direction of the arrows for the direction you want to move the mirror.
Page 136: Sun Visors
The Right Side Convex Mirror The side view mirror on the right is a convex mirror. This mirror gives you a wider view of the lanes on your right and behind you. RWARNING The side view mirror on the right makes objects appear smaller and farther away than they actually are.
Page 137 Power Point Electrical Outlet The power point outlet is located on the instrument panel to the right of the ashtray. This outlet should be used for optional electrical accessories. NOTE: Do not attempt to plug the cigarette lighter into the power point outlet. Damage could occur.
Page 138: Storage Compartments
Storage Compartments Your vehicle may have several small storage compartments: a glove compartment that locks. Use the round key to lock and unlock it. two map pockets on the panels of the front doors. two map pockets on the back of the front seats (on LX only).
Page 139 Using the Remote Control for the Trunk (If equipped) You can use the remote control on the driver’s door to unlock and open the trunk unless you lock the button with the main key. The valet key equipped with your vehicle can only open the doors and start the engine.
Page 140 Positive Location Floor Mat When installing or removing the driver’s side floor mat you must attach/detach the positive location grommet from the hook on the floor. The hook is just forward of the center of the driver’s seat. This is done by rotating the grommet one quarter turn, slipping the eyelet onto the hook, and sliding it to the floor.
Page 143 Luxury Audio System Using the Controls on Your New Radio How to turn the radio on and off Press the “VOL/PUSH ON” knob to turn the radio on. Press again to turn it off. How to adjust the volume Turn the “VOL/PUSH ON” knob to the right to increase the volume and to the left to decrease the volume.
Page 144 Using the “TUNE” function You can change the frequency up or down one increment at a time by pressing and releasing either the left b or right a side of the “TUNE” button. To change frequencies quickly, press and hold down either the right or left side of the “TUNE”...
Page 145 2. Press one of the memory buttons and hold the button until the sound returns. That station is now held in memory on that button. 3. Follow the two steps above for each station memory preset button you want to set. Using the Automatic Memory Store feature (“AUTOSET”) If the memory buttons have been set, either by...
Page 146 next time Auto Memory Store is activated on that band, the radio will store the next set of six strong stations. Adjusting the tone balance of your radio Increasing or decreasing bass and treble response Push the “BASS/TREB” popout knob to gain access to the bass and treble controls.
Page 147 Using the Digital Signal Processing (DSP) Feature Push the “DSP” button to activate the feature. The display will indicate which signal mode is in effect. To change the signal mode press either the left b or right a side of the selector button (located under the “DSP”...
Page 148 Using the Controls of Your Cassette Tape Player NOTE: Radio power must be on to use the cassette tape player. How to insert a tape Your cassette tape player is equipped with power loading. Once you insert a tape and push slightly (with the open edge to the right), the loading mechanism draws the tape the rest of the way in and play will begin after a...
Page 149 Rewinding the tape To rewind the tape, press the “REW” button. The radio will automatically begin playing while the tape is rewinding. The light above the “REW” button will blink while in the rewind mode. Press “REW” again or press the “TAPE”...
Page 150 How to eject the tape To stop the tape and eject the cassette, press the “EJECT” button. The tape will eject only when in the tape mode. The cassette cannot be ejected when the radio is playing an “AM” or “FM” station.
Page 151 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford Cassette Cleaning Cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 154 Midline Stereo and Stereo Cassette Radio Using the Controls on Your New Radio How to turn the radio on and off Press the “VOL/PUSH ON” knob to turn the radio on. Press again to turn it off. How to adjust the volume Turn the “VOL/PUSH ON”...
Page 155 select the station by using the memory buttons, which you can set to any desired frequency. These four methods are described below. Using the “TUNE” function You can change the frequency up or down one increment at a time by pressing and releasing either the left ( b ) or right ( a ) side of the “TUNE”...
Page 156 Setting the Station Memory Preset buttons Your radio is equipped with 6 station memory buttons. These buttons can be used to select up to 6 preset AM stations and 12 FM stations (6 in FM1 and 6 in FM2). Follow the easy steps below to set these buttons to the desired frequencies: 1.
Page 157 Adjusting speaker balance Balance control allows you to adjust the sound distribution between the right and left speakers. Press the top ( c ) of the “BAL” button to shift the sound to the right speakers, and press the bottom ( d ) of the “BAL”...
Page 158 NOTE: A cassette tape can be loaded with the ignition on whether or not the radio power is on. Inserting a cassette tape with the radio power off will turn the audio system on. After the cassette is ejected, radio play will return. How to locate a desired track on the tape There are four ways to quickly locate a desired selection on the tape.
Page 159 Using the “SEEK” function with your cassette tape player While in the tape mode, push the right ( a ) side of the “SEEK” button to seek forward to the next selection on the tape. Push the left ( b ) side to seek the previous tape selection. Using the “SCAN”...
Page 160 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford Cassette Cleaning Cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 161 Do not leave a tape in the cassette tape player. High heat in the vehicle can cause the cassette to warp. Common Radio Reception Conditions Several conditions prevent FM reception from being completely clear and noise-free, such as the following: 1.
Page 162 When the radio waves are reflected off objects or structures, the reflected signal cancels the normal signal, causing the antenna to pick up noise and distortion. Cancellation effects are most prominent in metropolitan areas, but also can become quite severe in hilly terrain and depressed roadways.
Page 163 All About Radio Frequencies The Federal Communications Commission (FCC) establishes the frequencies that AM and FM radio stations may use for their broadcasts. The allowable frequencies are, AM: 530, 540...1600, 1610 kHz in 10 kHz steps; FM: 87.9, 88.1...107.7, 107.9 MHz in 0.2 MHz steps. Not all frequencies will be assigned to a given area.
Page 164 Ask your dealer for a copy of this limited warranty. Service At Ford Electronics, we stand behind our audio systems with a comprehensive service and repair program. If anything should go wrong with your Ford audio system, return to your dealer for service.
Page 167 Luxury Audio System Using the Controls on Your New Radio How to turn the radio on and off Press the “VOL/PUSH ON” knob to turn the radio on. Press again to turn it off. How to adjust the volume Turn the “VOL/PUSH ON” knob to the right to increase the volume and to the left to decrease the volume.
Page 168 Using the “TUNE” function You can change the frequency up or down one increment at a time by pressing and releasing either the left b or right a side of the “TUNE” button. To change frequencies quickly, press and hold down either the right or left side of the “TUNE”...
Page 169 2. Press one of the memory buttons and hold the button until the sound returns. That station is now held in memory on that button. 3. Follow the two steps above for each station memory preset button you want to set. Using the Automatic Memory Store feature (“AUTOSET”) If the memory buttons have been set, either by...
Page 170 next time Auto Memory Store is activated on that band, the radio will store the next set of six strong stations. Adjusting the tone balance of your radio Increasing or decreasing bass and treble response Push the “BASS/TREB” popout knob to gain access to the bass and treble controls.
Page 171 Using the Digital Signal Processing (DSP) Feature Push the “DSP” button to activate the feature. The display will indicate which signal mode is in effect. To change the signal mode press either the left b or right a side of the selector button (located under the “DSP”...
Page 172 Using the Controls of Your Cassette Tape Player NOTE: Radio power must be on to use the cassette tape player. How to insert a tape Your cassette tape player is equipped with power loading. Once you insert a tape and push slightly (with the open edge to the right), the loading mechanism draws the tape the rest of the way in and play will begin after a...
Page 173 Rewinding the tape To rewind the tape, press the “REW” button. The radio will automatically begin playing while the tape is rewinding. The light above the “REW” button will blink while in the rewind mode. Press “REW” again or press the “TAPE”...
Page 174 How to eject the tape To stop the tape and eject the cassette, press the “EJECT” button. The tape will eject only when in the tape mode. The cassette cannot be ejected when the radio is playing an “AM” or “FM” station.
Page 175 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford Cassette Cleaning Cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 178 Midline Stereo and Stereo Cassette Radio Using the Controls on Your New Radio How to turn the radio on and off Press the “VOL/PUSH ON” knob to turn the radio on. Press again to turn it off. How to adjust the volume Turn the “VOL/PUSH ON”...
Page 179 select the station by using the memory buttons, which you can set to any desired frequency. These four methods are described below. Using the “TUNE” function You can change the frequency up or down one increment at a time by pressing and releasing either the left ( b ) or right ( a ) side of the “TUNE”...
Page 180 Setting the Station Memory Preset buttons Your radio is equipped with 6 station memory buttons. These buttons can be used to select up to 6 preset AM stations and 12 FM stations (6 in FM1 and 6 in FM2). Follow the easy steps below to set these buttons to the desired frequencies: 1.
Page 181 Adjusting speaker balance Balance control allows you to adjust the sound distribution between the right and left speakers. Press the top ( c ) of the “BAL” button to shift the sound to the right speakers, and press the bottom ( d ) of the “BAL”...
Page 182 NOTE: A cassette tape can be loaded with the ignition on whether or not the radio power is on. Inserting a cassette tape with the radio power off will turn the audio system on. After the cassette is ejected, radio play will return. How to locate a desired track on the tape There are four ways to quickly locate a desired selection on the tape.
Page 183 Using the “SEEK” function with your cassette tape player While in the tape mode, push the right ( a ) side of the “SEEK” button to seek forward to the next selection on the tape. Push the left ( b ) side to seek the previous tape selection. Using the “SCAN”...
Page 184 In order to keep your cassette tape player performing the way it was meant to, read and follow these simple precautions: Using a Ford Cassette Cleaning Cartridge to clean the tape player head after 10-12 hours of play will help maintain the best playback sound and proper tape operation.
Page 185 Do not leave a tape in the cassette tape player. High heat in the vehicle can cause the cassette to warp. Common Radio Reception Conditions Several conditions prevent FM reception from being completely clear and noise-free, such as the following: 1.
Page 186 When the radio waves are reflected off objects or structures, the reflected signal cancels the normal signal, causing the antenna to pick up noise and distortion. Cancellation effects are most prominent in metropolitan areas, but also can become quite severe in hilly terrain and depressed roadways.
Page 187 All About Radio Frequencies The Federal Communications Commission (FCC) establishes the frequencies that AM and FM radio stations may use for their broadcasts. The allowable frequencies are, AM: 530, 540...1600, 1610 kHz in 10 kHz steps; FM: 87.9, 88.1...107.7, 107.9 MHz in 0.2 MHz steps. Not all frequencies will be assigned to a given area.
Page 188 Ask your dealer for a copy of this limited warranty. Service At Ford Electronics, we stand behind our audio systems with a comprehensive service and repair program. If anything should go wrong with your Ford audio system, return to your dealer for service.
Page 189: Driving Your Crown Victoria
Driving Your Crown Victoria Driving with an Automatic Overdrive Transmission The automatic overdrive transmission operates very much like a regular automatic transmission, except it offers the extra overdrive feature. Putting Your Vehicle in Gear RWARNING Hold the brake pedal down while you move the gearshift lever from position to position.
Page 190 Your vehicle is equipped with a Brake Shift Interlock safety feature. This feature prevents the gearshift from being moved from the P (Park) position until the brake pedal is depressed. This feature is active when the ignition is in the ON position.
Page 191 The positions of the gearshift Once the gearshift is secure in the desired position, release the brake pedal and use the accelerator as necessary. R (Reverse) With the gearshift in the R (Reverse) position, the vehicle will move backward. You should always come to a complete stop before shifting into or out of R (Reverse).
Page 192 Driving Your vehicle’s gearshift is on the steering column. The Transmission Control Switch (TCS) is located on the end of the gearshift lever. The Transmission Control Indicator Light (O/D OFF) is located on the instrument panel. You can put the gearshift lever in any of the several positions.
Page 193 When to use j (Overdrive) Overdrive is the usual driving position for an automatic overdrive transmission. It works the same way Drive works, automatically upshifting or downshifting as the vehicle speeds or slows. However, Overdrive also shifts into a fourth gear —...
Page 194 P (Park) Always come to a complete stop before you shift into P (Park). Make sure that the gearshift is securely latched in P (Park). This locks the transmission and prevents the rear wheels from rotating. RWARNING Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park).
Page 195 RWARNING To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire. Traction Assist Your vehicle may be equipped with the optional Traction Assist system. This system helps prevent wheel spin in order to improve tire traction and is an especially useful feature when you drive in hilly areas or on slippery, icy or snowy roads.
Page 196: Steering Your Vehicle
inoperative. A cooling down period is required to prevent damage to the rear brakes. This time period varies and depends on brake usage during the cooling down period. Anti-Lock braking is not affected and will function normally during the cool down period. NOTE: Traction-Lok axles are not an available option on vehicles equipped with traction assist.
Page 197 Brakes Applying the Brakes Braking non ABS models Your vehicle has front and rear disc brakes with anti-lock (optional). They adjust automatically as the brake pads wear down. Apply the brake pedal gradually. Use the “squeeze” technique — push on the brake pedal with a steadily increasing force.
Page 198 Ford Motor Company has not found any detrimental effects of popular mobile radio transmitting equipment installed on vehicles with the anti-lock brake system, if the equipment is installed according to the manufacturer’s...
Page 199 The parking brake RWARNING Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). Your vehicle has an automatic parking brake release. As you move the gearshift selector to any forward gear with the engine running, the parking brake automatically releases.
Page 200 Always check the Brake Warning Light each time you start your engine. Driving with the parking brake on will cause the brakes to wear out quickly and will reduce the fuel economy. RWARNING If the parking brake is fully released, but the Brake System light remains on, have the brakes checked immediately.
Page 201 will appear in the message center when the ignition switch is in the ON position, and either the shutoff switch is in the OFF position, or a system fault has been detected. Normal vehicle operation does not require any action by the driver. RWARNING On vehicles equipped with Air Suspension, turn OFF the Air Suspension...
Page 202 Driving Under Special Conditions Tips for Safe Driving As with any new vehicle, yours may drive and handle differently from your previous vehicle. Use care until you become accustomed to its various features and driving characteristics. Operate your vehicle within reasonable limits. Sudden acceleration, deceleration, turning, or combinations of these maneuvers can cause a vehicle to behave differently than anticipated.
Page 203 RWARNING If your vehicle has speed control, do not use it on slippery roads. You could lose control of your vehicle and could injure someone. If your vehicle gets stuck (for example, in mud or snow), you may try to “rock” it out of the spot.
Page 204 Driving With a Heavy Load There are limits to the amount of weight your vehicle can carry or tow. The total weight of your vehicle, plus the weight of the passengers and cargo, should never be more than the Gross Vehicle Weight Rating (GVWR).
Page 205 Limiting Your Vehicle’s Load The load that you add to your vehicle must not exceed the maximum load stated on the Safety Compliance Certification Decal attached to the left front door pillar. To figure the weight of your vehicle’s load, add the weights of: the driver and passengers luggage and any other items that you put in...
Page 206 Your vehicle does not come from the factory fully equipped to tow. No towing packages are available through Ford or Lincoln/Mercury dealers. Because towing a trailer puts extra strain on your vehicle, you must follow certain...
Page 207 Ten to 15% of the loaded trailer’s weight should be on the tongue. However, the tongue load should never exceed 10% of the maximum weight that your vehicle can safely tow. RWARNING Do not tow a trailer when the temporary spare tire is being used.
Page 208 If you are not certain that you are using the right equipment in the proper manner, see your Ford or Lincoln-Mercury dealer. Do not use hitches that clamp onto your vehicle’s bumper. The bumper is not designed to bear the load.
Page 209 Tie down the load so that it does not shift and change the weight on the hitch. This will prevent damage to your vehicle and make your vehicle easier to handle. Hook-Up and Adjustment Procedure — Load Equalizing Hitch (option available in Canada only) Your vehicle is equipped with a rear air suspension system.
Page 210 Connecting the safety chains Always attach the trailer’s safety chains to your vehicle. They help protect your trailer if the hitch breaks. To connect the trailer’s safety chains: 1. Cross the chains under the trailer tongue and attach them to your vehicle’s frame or hook retainers.
Page 211 To get the proper equipment for hooking up your trailer’s lights, see your local trailer dealer and your Ford dealer. Be sure to follow their instructions carefully. If your vehicle is equipped with the optional trailer tow package, the proper lamp wiring and equipment has been installed at the factory.
Page 212 Driving While You Tow Be especially careful when driving while you tow a trailer. Never drive faster than 45 mph (70 km/h) when you tow in hilly country on hot days. Also, anticipate stops so that you can brake gradually. When you tow down steep grades, move the gearshift to 1 (Low).
Page 213: Roadside Emergencies
Roadside Emergencies Jump-Starting Your Vehicle Your vehicle’s battery may die if you leave the lights on or any electrical equipment on after you turn the engine off. If this happens, you may be able to jump-start from a booster battery to start your vehicle.
Page 214 first, then Milk of Magnesia, a beaten egg, or vegetable oil. Call a doctor immediately. To avoid damaging your vehicle or your battery, and to avoid injury to yourself, follow these directions for preparing your vehicle to jump-start and connecting the jumper cables in the order they are given.
Page 215 Connecting the jumper cables 1. Connect one end of the first jumper cable to the positive (+) terminal of the discharged battery. (You can connect either jumper cable to the positive (+) terminal, as long as you use the same cable for both positive terminals.) Most jumper cables have a red cable and a black cable.
Page 216 The 4.6L SFI engine...
Page 217 Jump-Starting 1. Make sure that the jumper cables are not in the way of moving engine parts, then start the booster vehicle. Run the engine at a moderate speed. 2. Let the discharged battery charge for a few minutes and then start the disabled vehicle. It may take a couple of tries before the vehicle starts.
Page 218: Changing A Tire
Changing a Tire If you get a flat tire while you are driving, do not apply the brake heavily. Instead, gradually decrease the speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. Park on a level spot, turn off the ignition, set the parking brake, and turn on the hazard flashers.
Page 219 When you drive with the temporary spare tire, DO NOT: exceed 50 mph (80 km/h) under any circumstances. load your vehicle so that it is heavier than the maximum vehicle load rating listed on the tire decal. tow a trailer. use tire chains on this tire.
Page 220 Spare Tire Location The spare is stored in the trunk. The spare tire location To remove the spare tire: 1. Lift off the spare tire cover (if equipped). 2. Unscrew the wing-nut holding down the spare tire. 3. Lift out the spare tire.
Page 221 Preparing to Change the Tire 1. Make sure that your vehicle will not move or roll. Put the gearshift in P (Park). Set the parking brake and block the wheel that is diagonally opposite the tire that you are changing. When one of the back wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack,...
Page 222 RWARNING To avoid injury, never run the engine with one wheel off the ground, such as when changing a tire. 2. Get out the spare tire and jack. RWARNING On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle.
Page 223 Removing and Replacing the Tire 1. Find the jacking location notches (a depression on plastic moulding) near the tire that you are changing. Align the two tabs on jack with rectangular notch on sheet metal. Slowly push jack straight until the tabs are against the side of the frame.
Page 224 NOTE: Never use the differential housing as a lift point. Jacking locations Locating the notch for the jack — rear wheels Locating the notch for the jack — front wheels 2. Turn the jack handle clockwise until the wheel clears the ground. Remove the wheel lug nuts.
Page 225 3. If you are replacing the front tire (with aluminum wheels) with the temporary spare tire, you need to remove the black dust shield. Gently pull the shield over the rubber o-rings and slide it off the wheel studs. Because the rubber o-rings are soft, they should pass through the holes in the shield.
Page 226 8. Place any wheel covers and ornaments in the trunk. 9. Put the tire, jack, and wrench away. Make sure the jack is securely fastened so it does not rattle when you drive. 10. Unblock the wheels. 11. Turn the air suspension ON (if so equipped). Installation of the black dust shield When installing the regular tire, reinstall the black dust shield by orienting and sliding the...
Page 227 Install the center ornament on the wheel and be sure it is snapped into place all the way around using the palm of the hand or a rubber mallet. Steel wheel with full wheelcover Steel wheel with full wheelcover Remove the wheelcover from the wheel using the flanged end of the wheel nut wrench by inserting the handle and then prying against the inner wheelcover flange.
Page 228 If you have the anti-theft locking spoked wheel cover, each wheel cover has a lock bolt behind the center hub ornament. You need a special key wrench (stored in the glove box) to pry this ornament off and to remove the lock bolt. Do not lose this wrench or you will not be able to remove the wheel cover.
Page 229: Towing Your Vehicle
Towing Your Vehicle If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. Recommended towing options include wheel lift towing or flat bed towing. Before your vehicle can be towed, the air suspension switch in the luggage compartment needs to be turned to the OFF position.
Page 230 When calling for a tow truck, tell the operator what kind of vehicle you have. A towing manual is available from Ford Motor Company for all authorized tow truck operators. Have your tow truck driver refer to this manual for the proper hook-up and towing procedures for your vehicle.
Page 231: Customer Assistance
Customer Assistance Roadside Assistance Ford Motor Company has set up a 24-hour, seven-day-a-week hotline with trained operators that put you in touch with the help you need if you experience a problem with your vehicle. This complimentary service is provided to you...
Page 232 1-800-241-FORD (in Canada call 1-800-665-2006). If You Have a Service Problem Ford Motor Company has authorized Ford and Lincoln-Mercury dealerships that can service your vehicle for you. This chapter tells you how to get service or maintenance for your vehicle.
Page 233 If you are away from home when your vehicle needs to be serviced, or if you need more help than the dealer gave you, contact the Ford Customer Assistance Center to find an authorized dealership that may be able to help.
Page 234 Please have the following information available when contacting Ford Customer Assistance: your telephone number (both business and home) the name of the dealer and the city where the dealership is located the year and make of your vehicle the date purchased...
Page 235: The Dispute Settlement Board
Review? The Board reviews all product performance and service complaints on Ford, Mercury and Lincoln Cars and Ford and Mercury Light Trucks under warranty that have not been resolved by a dealer or Ford Motor Company. The Board does not review issues involving:...
Page 236 How Does the Board Work? The Board has four members: three consumer representatives a Ford or Lincoln-Mercury dealer Consumer candidates for Board membership are recruited and trained by an independent consulting firm. Dealers are chosen because of their business leadership qualities.
Page 237 The decisions of the Board are binding on the dealer and Ford, but customers may have other options available to them under state or federal law. The decisions of the Board, however, may be...
Page 238 Board address. At the same time, your dealer and Ford Motor Company representative are asked to submit statements. To review your case properly, the Board needs...
Page 239: Reporting Safety Defects
National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 240 If a specific item of concern arises, where a solution cannot be reached between a vehicle owner, Ford of Canada, and/or one of its dealers (that all parties can agree upon), the owner may wish to use the services offered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 241 Use of leaded fuel in your vehicle without a proper conversion may damage the effectiveness of your emissions control system and may cause engine knocking or serious engine damage. Ford Motor Company is not responsible for any damage that is caused by use of improper fuel.
Page 242 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write to: If you are in other foreign countries, contact the nearest Ford dealership.
Page 243: Accessories
Accessories Ford Accessories for Your Vehicle Ford has many fine products available from your dealer to clean your vehicle and protect its finishes. For best results, use the following, or products of equivalent quality: A wide selection of accessories is available through your local authorized dealer.
Page 244 Safety, Comfort, and Convenience NOTE: When adding accessories, equipment, passengers, and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR, GAWR as shown on the Safety Compliance Certification Label).
Page 245 5 watts or less will not ordinarily affect your vehicle’s operation.) NOTE: Because we have no control over the installation, design, or manufacture of such systems, Ford cannot assume responsibility for any adverse effects or damage that may result if you use this equipment.
Page 249: Servicing Your Crown Victoria
Servicing Your Crown Victoria Service Made Easy Ford has two goals for servicing your vehicle. 1. When we can, we design parts that do not need to be serviced. 2. We want to make servicing your vehicle as easy as possible. To help you:...
Page 250 Motorcraft parts are designed and built to provide the best performance in your vehicle. Using these parts for replacement is your assurance that Ford-built quality stays in your vehicle. NOTE: Always dispose of used automotive fluids in a responsible manner. Follow your community’s standards for...
Page 251 Never get under a vehicle while it is supported by a jack only. If you must work under a vehicle, use safety stands. Keep all lit cigarettes and other smoking materials away from the battery and all fuel-related parts. Working with the engine off: 1.
Page 252: Opening The Hood
Opening the Hood 1. Inside the vehicle, pull the hood release located under the lower left corner of the instrument panel. The hood release under the instrument panel 2. Go around to the front of the vehicle, and release the auxiliary catch that is located under the front edge of the hood at the center of the vehicle.
Page 253: Engine Compartment
Whenever you close the hood, latch it securely. NOTE: Apply lubricant to the hood latch at six-month intervals to maintain smooth and trouble-free operation. Engine Compartment Your vehicle has a 4.6 liter engine. The following page shows a diagram of where to find items that you should regularly service.
Page 255: Filling The Fuel Tank
Cleaning the Engine A clean engine is more efficient because a buildup of grease and dirt acts as an insulator, keeping the engine warmer than usual. Extreme care must be used if a power washer is used to clean the engine. The high pressure fluid could penetrate sealed parts and assemblies causing damage or malfunctions.
Page 256 2. Put the nozzle all the way inside the fuel filler pipe before pumping the fuel. NOTE: If you spill any fuel on the body of your vehicle, clean it off immediately. The fuel may dull or soften the paint if you do not wash it off.
Page 257 Octane recommendations Your engine is designed to use fuel with an octane rating of 87. In most cases it is not necessary to use a fuel with an octane rating higher than 87. At service stations, the octane rating is displayed in a label on the pumps. Using a fuel with a lower octane rating can cause persistent and heavy knocking, which can damage the engine.
Page 258 Gasolines for clean air Fuels in certain areas of the country are required to contain oxygenates to improve air quality. Common oxygenates are ethanol or grain alcohol (blended at no more than 10%), methanol or wood alcohol (blended at no more than 5% with cosolvents and additives), and MTBE or methyl tertiary butyl ether (blended at no more than 15%).
Page 259 RWARNING Gasoline or gasoline blended with methanol can cause blindness and possible death when swallowed. If any fuel is swallowed, call a physician or poison control center immediately. Avoid breathing vapors while refueling. If fuel is splashed on the skin, wash with soap and water.
Page 260: Calculating Fuel Economy
Calculating Fuel Economy Fuel economy is an estimate of the efficiency of your vehicle, and can be calculated as Miles Per Gallon (MPG) or Liters Per 100 Kilometers (L/100K). Do not calculate fuel economy during your vehicle’s break-in period. This would not be an accurate estimate of how much fuel your vehicle will normally use.
Page 261 The following decrease fuel economy: Lack of regular, scheduled maintenance Rapid acceleration and excessive speed Driving with your foot on the brake Sudden stops Extended engine idling Using speed control in hilly terrain Extended use of the A/C, defroster, rear window defroster and other accessories Underinflated tires Heavy loads...
Page 262 Engine Oil Recommendations We recommend using Motorcraft oil or an equivalent oil meeting Ford Specification ESE-M2C153-E and displaying the American Petroleum Institute CERTIFICATION MARK on the front of the container. The API Certification Mark Never use: “Non-Detergent” oils Oils labeled API SA, SB, SC, SD, SE, SF or SG...
Page 263 Checking and Adding Engine Oil Since the proper amount of engine oil is important for safe engine operation, check the oil using the dipstick each time you put fuel in your vehicle. Remember the engine must be off, the oil must be warm and the vehicle must be parked on level ground.
Page 264 7. Put the dipstick back in and make sure it is fully seated. It may be necessary to add some oil between oil changes. Make sure you use a CERTIFIED engine oil of the preferred viscosity. Your vehicle’s warranty coverage may not apply if engine damage is caused by the use of improper engine oil.
Page 265: Engine Coolant
RWARNING Continuous contact with USED motor oil has caused cancer in laboratory mice. Protect your skin by washing with soap and water. Engine Coolant Checking the Engine Coolant NOTE: Be sure to read and understand Precautions When Servicing Your Vehicle at the beginning of this chapter. RWARNING The cooling fan is automatic and may come on at any time.
Page 266 The engine coolant recovery reservoir Checking hoses Inspect all engine and heater system hoses and hose connections for deterioration, leaks, and loose hose clamps as specified in the Maintenance Schedule and Record booklet. Repair or replace with Motorcraft hoses or equivalent as necessary. Adding engine coolant RWARNING Do not put engine coolant in the container...
Page 267 If the coolant level is low, add a 50/50 or appropriate mixture of water and the type of engine coolant that Ford specifies. You may add water by itself only in an emergency, but you should replace it with a 50/50 or appropriate mixture as soon as possible.
Page 268 Ford Premium Cooling System Fluid is an optimized formula that will protect all metals and rubber elastomers used in Ford engines for four years or 50,000 miles (80,000 km). It is not necessary and not recommended to use supplemental coolant additives in your gasoline powered vehicle.
Page 269 Use Ford Premium Cooling System Fluid E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B) or an equivalent engine coolant that meets Ford Specification ESE-M97B44-A. Leave the engine coolant in all year. Make sure that the coolant will not freeze at the temperature level in which you drive during winter months.
Page 270 With the engine OFF and cool, remove the pressure cap, located on the coolant reservoir. Remove the heater hose and clamp, located on the rear of the intake manifold. Add a 50/50 mixture of specified coolant and water to the coolant reservoir. Refer to Refill Capacities later in this chapter for the correct amount.
Page 271 If the battery needs water quite often, have the charging system checked for a possible malfunction. Help Us Protect Our Environment Ford Motor Company strongly recommends that used lead-acid batteries be returned to an authorized recycling facility for disposal. Battery recycling symbol...
Page 272 Because your vehicle’s engine is electronically controlled by a computer, some control conditions are maintained by power from the battery. If you ever disconnect the battery or install a new battery, you must allow the computer to “relearn” its idle conditions before your vehicle will drive properly.
Page 273 The reservoir for the windshield washer fluid RWARNING Do not put windshield washer fluid in the container for the engine coolant. Use specially formulated windshield washer fluid rather than plain water, because specially formulated washer fluids contain additives that dissolve road grime. For safety reasons, washer fluids containing an appropriate antifreeze such as methanol should be used in freezing weather (temperatures below 32˚F [0˚C]).
Page 274 Wiper Blades Check the windshield wiper blades at least twice a year. Also check them whenever they seem less effective than usual. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades.
Page 275 Drive at safe speeds. If you do not take these precautions, your tires may fail or go flat. Ford Motor Company recommends obeying posted speed limits. RWARNING Driving too fast for conditions creates the possibility of loss of vehicle control.
Page 276 At least once a month, check the pressure in all your vehicle’s tires, including the spare. Use an accurate tire pressure gauge. Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 3 miles (5 km).
Page 277 Rotating the tires NOTE: Use the five tire rotation only when the conventional spare wheel is the same as the road wheels. (Do not mix the steel wheel with aluminum wheels in tire rotation sequence.)
Page 278 Replacing the Tires Replace any tires that show wear bands. When your tire shows a wear band, it has only 1/16 inch (2 mm) of tread left. A worn-out tire Because your vehicle’s tires may wear unevenly, you may need to replace them before a wear band appears across the entire tread.
Page 279 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation — Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 280 Traction A B C The traction grades, from highest to lowest, are A, B, and C, and they represent the tire’s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
Page 281 Snow Tires and Chains The tires on your vehicle have all-weather treads that provide traction in rain or snow. However, during the winter months in some climates, you may need to use snow tires and occasionally chains for your tires. RWARNING Snow tires must be the same size and grade as the tires you currently have on...
Page 282: Automatic Transmission Fluid
Cleaning the Wheels Wash the wheels with the same detergent you use to wash your vehicle’s body. Do not use acid-based wheel cleaners, steel wool, abrasives, fuel, or strong detergents. These substances will damage protective coatings. Use tar and road oil remover to remove grease and tar.
Page 283 NOTE: Your vehicle should not be driven if the fluid level is below the bottom hole on the dipstick. Wipe off the dipstick cap, pull the dipstick out and wipe the indicator end clean. Put the dipstick back into the filler tube and make sure it is fully seated.
Page 284: Brake Fluid
Detail of the automatic transmission dipstick Brake Fluid Under normal circumstances, your vehicle should not use up brake fluid rapidly. However, expect the level of the brake fluid to slowly fall as you put more mileage on your vehicle and the brake lining wears.
Page 285 If the fluid is low, carefully clean and remove the cap from the reservoir. Fill the reservoir to the MAX line with Ford High Performance DOT 3 Brake Fluid C6AZ-19542-AA, C6AZ-19542-BA, or equivalent DOT 3 fluid meeting Ford specification ESA-M6C25-A.
Page 286: Power Steering Fluid
Power Steering Fluid Check the level of the power steering fluid at least twice a year (i.e., every Spring and Fall). Checking and Adding Power Steering Fluid 1. Start the engine and let it run until the power steering fluid reaches normal operating temperature.
Page 287 Fluid level for power steering Use only power steering fluid that meets Ford Specification Mercon ATF XT-2-QDX. If the power steering fluid is low, do not drive your vehicle for a long period of time before adding fluid. This can damage the power steering pump.
Page 288 electrical parts, check the appropriate fuses (conventional and high current) or circuit breakers. The following charts tell you which fuses or circuit breakers protect the wiring for each electrical part of your vehicle. If a fuse blows or a circuit breaker opens a circuit, all the parts of your vehicle that use that circuit will not work.
Page 289 The Instrument Panel Fuses, Circuit Breakers and Relays...
Page 291 These, like fuses, open when the circuit load exceeds their amperage rating. High current fuses may be purchased from your Ford or Lincoln-Mercury dealer. The high current fuse panel is located in the engine compartment near the battery.
Page 292 The high current fuse panel...
Page 293 The high current fuses and relays...
Page 294 Checking and Replacing Fuses If you need to check a fuse, follow these steps: 1. Find the fuse panel to the left of the steering column. Remove the fuse panel cover to expose the fuse panel. 2. Check the fuse to see if it is blown. Look through the clear side of the fuse to see if the metal wire inside is separated.
Page 295 3. Replace the fuse with one that has the right amperage rating. (See the following charts.) RWARNING Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire.
Page 296 These, like fuses, open when the circuit lead exceeds their amperage rating. Fuse links may be purchased from your Ford or Lincoln-Mercury dealer. See the following charts to find out which electrical parts are protected by a fuse...
Page 297 Lights and Bulb Replacement It is a good idea to check the operation of the following lights frequently: headlamps tail lamps brakelamps hazard flasher high-mount brakelamp turn signals side markers license plate lamp The alignment of your headlamps should be checked if: oncoming motorists frequently signal you to turn off your vehicle’s high beams when you...
Page 298 Headlamp Bulb The headlamps on your vehicle use replaceable bulbs. When the lamp burns out, simply replace the bulb, rather than the whole lamp. RWARNING Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Page 299 Removing the headlamp bulb 1. Make sure that the headlamp switch is in the OFF position. 2. Lift the hood, open access panel above headlamp and find the bulb in the headlamp socket. 3. Remove the electrical connector by pulling off the bulb base.
Page 300 Parts of the high-mount brakelamp To remove the high-mount brakelamp: 1. Remove the two retaining screws with a Phillips screwdriver. 2. Then lift the whole assembly up and over the retaining brackets. Do not move upper part of plastic attachment brackets. 3.
Page 301 Using the Right Bulbs...
Page 302: Emission Control System
Emission Control System Your vehicle is equipped with a catalytic converter which enables your vehicle to comply with applicable exhaust emission requirements. RWARNING Exhaust leaks may result in the entry of harmful and potentially lethal fumes into the passenger compartment. Under extreme conditions excessive exhaust temperatures could damage the fuel system, the interior floor covering, or...
Page 303 Ford strongly recommends the use of genuine Ford replacement parts. If other than Ford or Motorcraft parts or Ford authorized remanufactured parts are used for maintenance replacements or for the service of components...
Page 304 By law, anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles is not permitted to intentionally remove an emission control device or prevent it from working. In some of the United States and in Canada, vehicle owners may be liable if their emission control device is removed or is prevented from working.
Page 305 varies with individual driving patterns. To complete this requirement in the minimum amount of time, refer to the OBD II Drive Cycle defined below. If the vehicle owner cannot or does not want to do the additional driving required by law, a service center can perform this drive cycle as it would any other type of repair work.
Page 306 6. Continue to drive the vehicle in city traffic at speeds between 25 and 40 mph (40-64 km/h) for 15 minutes. During the 15 minute drive cycle the following modes must be achieved: a. at least 5 stop and idle modes at 10 seconds each b.
Page 307 Refill Capacities, Motorcraft Parts, and Lubricant Specifications Refill Capacities NOTE: Rear axle lube quantities must be replaced every 100,000 miles (160,000 km) or if the axle has been submerged in water. Otherwise, the lube should not be checked or changed unless a leak is suspected or repair required.
Page 308 Motorcraft Parts If a spark plug is removed for examination, it must be reinstalled in the same cylinder. For 4.6L (2V) engines: Cylinders #1, #2, #3, #4 have a PG suffix. Cylinders #5, #6, #7, #8 have a P suffix. If a spark plug needs to be replaced, use only spark plugs with the service number suffix letter as shown on the engine decal.
Page 309: Lubricant Specifications
Lubricant Specifications NOTE: Rear axle lube quantities must be replaced every 100,000 miles (160,000 km) or if the axle has been submerged in water. Otherwise, the lube should not be checked or changed unless a leak is suspected or repair required.
Page 310: Vehicle Storage
Vehicle Storage Maintenance Tips If you plan on storing your vehicle for an extended period of time (60 days or more), refer to the following maintenance recommendations to ensure your vehicle stays in good operating condition. General Store all vehicles in a dry, ventilated place. Protect from sunlight, if possible.
Page 311 Ford Gas Stabilizer should be added whenever actual or expected storage periods exceed 60 days. Follow the instructions on the label. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system.
Page 312 Battery Check and recharge as necessary. Keep connections clean and covered with a light coat of grease. If storing your vehicle for more than 30 days without recharging the battery, it may be advisable to disconnect the battery cables to ensure battery charge is maintained for quick starting.
Page 314 Label Locations...
Page 324: Index
Index ABS warning light (see Anti-lock brake system) ..Accessory position on the ignition ..37 Accessory power source, power point outlet ..Additives, engine oil .
Page 325 Assistance (see Customer assistance)..Audio system (see Electronic sound system) ..Automatic transmission driving an automatic overdrive ..fluid, adding ... . . fluid, checking .
Page 326 Brakes (continued) fluid, checking and adding ..fluid, specifications ..front disc ....new brake linings.
Page 327 Chime key in ignition ... . . 38 safety belt ... . . Circuit breakers checking and replacing ..see also fuses .
Page 328 Customer Assistance Center, Ford (U.S.). . Customer Assistance Centre, Ford of Canada... . Dashboard (see Instrument panel) ..87 Daytime running light system ..
Page 329 Emergencies, roadside assistance....battery acid spills ... jump-starting ... . . towing .
Page 330 ....Exhaust fumes ....43 Extended Service Plan, Ford ..Federal Communications Commission . . .
Page 331 Fuel and distance computer (continued) select button ....75 to empty indicator ... 76 trip distance ....79 trip/reset button .
Page 332 Gearshift automatic operation ..column-mounted ... positions ....shift-lock.
Page 333 Identification Number, Vehicle (VIN) . . . Idle relearning ....speed ....41 Ignition chime .
Page 334 Lamps autolamp delay system ..bulb replacement specifications chart . . checking ....daytime running light system ..dome lamps .
Page 335 Load limits GAWR ....GVWR ....trailer towing ... . . Lubricant specifications .
Page 336 Odometer description ... . . trip odometer ... . . 60 Oil filter ....Oil (see Engine oil) .
Page 337 Radio (see Electronic sound systems) . . . Rear air suspension system ..Rearview mirror... . . Rear window, defroster ..Refill capacities for fluids .
Page 338 Safety seats for children and air bags ... . attaching with tether straps ..26 automatic locking mode (retractor) ..28 in center seating positions .
Page 339 Speedometer ... . . Starting your vehicle preparing to start your vehicle ..39 starting a cold engine ..40 starting after a collision .
Page 340 Traction-lok rear axle ..Trailer towing calculating maximum trailer weight . . safety chains ... . . tips ....trailer brakes .
Page 341 Viscosity (see Engine oil) ..Visor (see Sun visor)... Warm engine, starting ... 40 Warning chimes key in ignition .
Page 342: Service Station Information
Service Station Information...

This manual is also suitable for:

Crown victoria

Ford 1996 Crown Victoria Manual

Quick Links

Related Manuals for Ford 1996 Crown Victoria

Summary of Contents for Ford 1996 Crown Victoria

This manual is also suitable for:

Table of Contents