Page 1 2008 Buick LaCrosse Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-2 Rear Seats ... 1-8 Safety Belts ... 1-9 Child Restraints ... 1-29 Airbag System ... 1-54 Restraint System Check ... 1-68 Features and Controls ... 2-1 Keys ...
Page 2: Canadian Owners
We reserve the right to make changes after that time without notice. For vehicles ﬁrst sold in Canada, substitute the name “General Motors of Canada Limited” for Buick Motor Division whenever it appears in this manual. This manual describes features that may be available in this model, but your vehicle may not have all of them.
Page 3: Using This Manual
Using this Manual Many people read the owner manual from beginning to end when they ﬁrst receive their new vehicle to learn about the vehicle’s features and controls. Pictures and words work together to explain things. Index A good place to quickly locate information about the vehicle is the Index in the back of the manual.
Page 4: Vehicle Symbols
Vehicle Damage Warnings You will also ﬁnd notices in this manual. Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
Page 5: Table Of Contents
Section 1 Front Seats ...1-2 Power Seats ...1-2 Power Lumbar ...1-3 Heated Seats ...1-3 Reclining Seatbacks ...1-4 Head Restraints ...1-6 Center Seat ...1-7 Rear Seats ...1-8 Split Folding Rear Seat ...1-8 Safety Belts ...1-9 Safety Belts: They Are for Everyone ...1-9 How to Wear Safety Belts Properly ...1-14 Lap-Shoulder Belt ...1-22 Safety Belt Use During Pregnancy ...1-27...
Page 6: Front Seats
Front Seats Power Seats Driver Side shown, Passenger Side similar If the vehicle has power seats, the controls used to operate them are located on the outboard side of the seats. To adjust the seat, do any of the following: •...
Page 7: Power Lumbar
Power Lumbar On seats with power lumbar, the control is located on the outboard side of the seat cushion. Press the front of the control to increase lumbar support. Press the rear of the control to decrease lumbar support. Keep in mind that as your seating position changes, as it may during long trips, so should the position of your lumbar support.
Page 8: Reclining Seatbacks
Reclining Seatbacks CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver’s seat only when the vehicle is not moving.
Page 9 To return the seatback to an upright position, do the following: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position. 2. Push and pull on the seatback to make sure it is locked.
Page 10: Head Restraints
Head Restraints Adjust the head restraint so that the top of the restraint is at the same height as the top of the occupant’s head. This position reduces the chance of a neck injury in a crash. Pull the head restraint up to raise it.
Page 11: Center Seat
Center Seat Your vehicle may have a front center seat. There are cupholders on the underside of the seat cushion. To use them, raise the seat cushion. This seat can also be converted to a storage area by lowering the armrest. See Center Console Storage on page 2-53.
Page 12: Rear Seats
Rear Seats Split Folding Rear Seat If your vehicle has this feature, both sides of the rear seatback can be folded down. This gives direct access to the trunk. Make sure the front seats are not reclined. If they are, the rear seatback(s) may not fold down all the way.
Page 13 Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. CAUTION: Do not let anyone ride where he or she cannot wear a safety belt properly.
Page 14: Why Safety Belts Work
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it is just a seat on wheels. 1-10...
Page 15 Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... 1-11...
Page 16 or the instrument panel... 1-12 or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense.
Page 17 Questions and Answers About Safety Belts Will I be trapped in the vehicle after a crash if I am wearing a safety belt? You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Page 18: How To Wear Safety Belts Properly
How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and babies. If a child will be riding in your vehicle, see Older Children on page 1-29 or Infants and Young Children on page 1-33.
Page 19 What is wrong with this? The shoulder belt is too loose. It will not give as much protection this way. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt snugly against your body.
Page 20 What is wrong with this? The lap belt is too loose. It will not give nearly as much protection this way. 1-16 CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Page 21 What is wrong with this? The belt is buckled in the wrong place. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Page 22 What is wrong with this? The belt is over an armrest. 1-18 CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt.
Page 23 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 24 What is wrong with this? The belt is behind the body. 1-20 CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 25 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to ﬁx it.
Page 26: Lap-Shoulder Belt
Lap-Shoulder Belt All seating positions in your vehicle have a lap-shoulder except for the center front passenger position, if your vehicle has one, which has a lap belt. See Lap Belt on page 1-28 for more information. Here is how to wear a lap-shoulder belt properly. 1.
Page 27 4. If equipped with a shoulder belt height adjuster, move it to the height that is right for you. Improper shoulder belt height adjustment could reduce the effectiveness of the safety belt in a crash. See “Shoulder Belt Height Adjustment” later in this section.
Page 28 Shoulder Belt Height Adjuster Your vehicle has a shoulder belt height adjuster for the driver and right front passenger position. Adjust the height so that the shoulder portion of the belt is centered on your shoulder. The belt should be away from your face and neck, but not falling off your shoulder.
Page 29 1. Pull the elastic cord out from between the edge of 2. Place the guide over the belt and insert the two the seatback and the interior body to remove the edges of the belt into the slots of the guide. guide from its storage clip.
Page 30 3. Be sure that the belt is not twisted and it lies ﬂat. The elastic cord must be under the belt and the guide on top. 1-26 CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
Page 31: Safety Belt Use During Pregnancy
4. Buckle, position, and release the safety belt as described previously in this section. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guide, squeeze the belt edges together so that you can take them out of the guide.
Page 32: Lap Belt
Lap Belt This part is only for the lap belt. To learn how to wear a lap-shoulder belt, see Lap-Shoulder Belt on page 1-22. You vehicle may have a center seating position. When you sit in the center front seating position, you have a lap safety belt, which has no retractor.
Page 33: Child Restraints
Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/ retailer will order you an extender. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Page 34: Safety Belts
Use a booster seat with a lap-shoulder belt until the child passes the below ﬁt test: • Sit all the way back on the seat. Do the knees bend at the seat edge? If yes, continue. If no, return to the booster seat.
Page 35 CAUTION: Never do this. Here two children are wearing the same belt. The belt cannot properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. 1-31...
Page 36 CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. In a crash, the child would not be restrained by the shoulder belt. The child might slide under the lap belt. The belt force would then be applied right on the abdomen.
Page 37 Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 38 CAUTION: People should never hold an infant in their arms while riding in a vehicle. An infant does not weigh much — until a crash. During a crash an infant will become so heavy it is not possible to hold it. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) infant will suddenly become a 240 lb (110 kg) force on a person’s arms.
Page 39 CAUTION: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 40: Child Restraints
What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 41: Child Restraint Systems
CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
Page 42 A booster seat (C-D) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. 1-38 Securing an Add-On Child Restraint in the Vehicle CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly...
Page 43: Where To Put The Restraint
When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer.
Page 44 A label on your sun visor says, “Never put a rear-facing child seat in the front.” This is because the risk to the rear-facing child is so great, if the airbag deploys. CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates.
Page 45: Lower Anchors And Tethers For Children (Latch)
When securing a child restraint in a rear seating position, study the instructions that came with your child restraint to make sure it is compatible with this vehicle. Wherever you install a child restraint, be sure to secure the child restraint properly. Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle.
Page 46: Top Tether Anchor
Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
Page 47 Lower Anchor and Top Tether Anchor Locations Seating positions with top tether anchors. (Lower Anchor): Seating positions with two lower anchors. Rear Seat To assist you in locating the lower anchors, each seating position with lower anchors has two labels, near the crease between the seatback and the seat cushion.
Page 48: Securing A Child Restraint Designed For The Latch System
Do not secure a child restraint in a position without a top tether anchor if a national or local law requires that the top tether be attached, or if the instructions that come with the child restraint say that the top tether must be attached.
Page 49 CAUTION: (Continued) anchor or attachment to come loose or even break during a crash. A child or others could be injured if this happens. To help prevent injury to people and damage to your vehicle, attach only one child restraint per anchor. CAUTION: Children can be seriously injured or strangled if a shoulder belt is wrapped around their neck...
Page 50 2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor. 2.2.
Page 51: Securing A Child Restraint In A
If the position you are using has a ﬁxed headrest or head restraint and you are using a dual tether, route the tether around the headrest or head restraint. 3. Push and pull the child restraint in different directions to be sure it is secure. Securing a Child Restraint in a Rear Seat Position When securing a child restraint in a rear seating...
Page 52 If your child restraint does not have the LATCH system, you will be using the safety belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say.
Page 53 4. Pull the rest of the shoulder belt all the way out of 5. To tighten the belt, push down on the child restraint, the retractor to set the lock. pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor.
Page 54: Securing A Child Restraint In The Center Front Seat Position
6. If your child restraint has a top tether, follow the child restraint manufacturer’s instructions regarding the use of the top tether. See Lower Anchors and Tethers for Children (LATCH) on page 1-41 for more information. 7. Push and pull the child restraint in different directions to be sure it is secure.
Page 55 CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. Even though the passenger sensing system is designed to turn off the right front passenger’s frontal airbag if the system detects a rear-facing child restraint, no system is...
Page 56 3. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. 4. Push the latch plate into the buckle until it clicks. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if necessary.
Page 57 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 58: Airbag System
Airbag System Your vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger Your vehicle may also have the following airbags: • A roof-rail airbag for the driver and the passenger seated directly behind the driver.
Page 59 CAUTION: Frontal airbags are designed to deploy in moderate to severe frontal and near frontal crashes. They are not designed to inﬂate in rollover, rear crashes, or in many side crashes. Roof-rail airbags are designed to inﬂate in moderate to severe crashes where something hits the side of your vehicle.
Page 60 CAUTION: Airbags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them. Young children and infants need the protection that a child restraint system can provide.
Page 61: Where Are The Airbags
Where Are the Airbags? The driver’s frontal airbag is in the middle of the steering wheel. The right front passenger’s airbag is in the instrument panel on the passenger’s side. 1-57...
Page 62 Driver Side shown, Passenger Side similar If your vehicle has roof-rail airbags for the driver, right front passenger, and second row outboard passengers, they are in the ceiling above the side windows. 1-58 CAUTION: If something is between an occupant and an airbag, the airbag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 63: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? Frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver’s or right front passenger’s head and chest. However, they are only designed to inﬂate if the impact exceeds a predetermined deployment threshold.
Page 64: What Makes An Airbag Inﬂate
What Makes an Airbag Inﬂate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inﬂator. Gas from the inﬂator ﬁlls the airbag causing the bag to break out of the cover and deploy. The inﬂator, the airbag, and related hardware are all part of the airbag module.
Page 65 CAUTION: When an airbag inﬂates, there may be dust in the air. This dust could cause breathing problems for people with a history of asthma or other breathing trouble. To avoid this, everyone in the vehicle should get out as soon as it is safe to do so.
Page 66: Passenger Sensing System
Passenger Sensing System Your vehicle has a passenger sensing system for the right front passenger’s position. The passenger airbag status indicator will be visible on the instrument panel when you start your vehicle. The words ON and OFF will be visible during the system check.
Page 67 CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. Even though the passenger sensing system is designed to turn off the right front passenger’s frontal airbag if the system detects a rear-facing child restraint, no system is...
Page 68 If, after reinstalling the child restraint and restarting the vehicle, the on indicator is still lit, check to make sure that the vehicle’s seatback is not pressing the child restraint into the seat cushion. If this happens, slightly recline the vehicle’s seatback and adjust the seat cushion if possible.
Page 69 Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “Safety Belts” and “Child Restraints” in the Index for additional information about the importance of proper restraint use.
Page 70: Servicing Your Airbag-Equipped Vehicle
The passenger sensing system may suppress the airbag deployment when liquid soaks into the seat. If this happens, the off indicator in the passenger airbag status indicator and the airbag readiness light on the instrument panel will be lit. The system should resume normal operation after the seat is allowed to dry.
Page 71 Adding Equipment to Your Airbag-Equipped Vehicle Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? Yes. If you add things that change your vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Page 72: Restraint System Check
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts.
Page 73: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 74 NOTES 1-70...
Page 75: Features And Controls
Section 2 Keys ...2-3 Remote Keyless Entry (RKE) System ...2-4 Remote Keyless Entry (RKE) System Operation ...2-5 Remote Vehicle Start ...2-8 Doors and Locks ...2-11 Door Locks ...2-11 Power Door Locks ...2-11 Delayed Locking ...2-12 Automatic Door Lock ...2-12 Programmable Automatic Door Unlock ...2-12 Rear Door Security Locks ...2-12 Lockout Protection ...2-13 Trunk ...2-14...
Page 76 Section 2 Object Detection Systems ...2-41 Ultrasonic Rear Parking Assist (URPA) ...2-41 ® OnStar System ...2-43 Universal Home Remote System ...2-47 Universal Home Remote System ...2-47 Universal Home Remote System Operation ...2-48 Features and Controls Storage Areas ...2-52 Glove Box ...2-52 Cupholder(s) ...2-52 Center Console Storage ...2-53 Convenience Net ...2-54...
Page 77: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and they could be seriously injured or killed if caught in the path of a closing...
Page 78: Remote Keyless Entry (Rke) System
® Any new PASS-Key III key must be programmed before it will start the vehicle. See PASS-Key Operation on page 2-22 for more information on programming a new key. Notice: If you ever lock your keys in your vehicle, you may have to damage the vehicle to get in. Be sure you have spare keys.
Page 79: Remote Keyless Entry (Rke) System Operation
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions will work up to 195 feet (60 m) away, however, the operating range may be less while the vehicle is running. There are other conditions which can affect the performance of the transmitter.
Page 80 (Remote Trunk Release): Press and hold about one second to release the trunk lid. The transmission must be in PARK (P) for this feature to operate. (Panic Alarm): Press to activate the alarm. The headlamps will ﬂash and the horn will sound repeatedly for two minutes.
Page 81: Battery Replacement
Battery Replacement Replace the battery if the KEY FOB BATT LOW message displays in the DIC. See “KEY FOB BATTERY LOW” under DIC Warnings and Messages on page 3-58 for additional information. Notice: When replacing the battery, use care not to touch any of the circuitry.
Page 82: Remote Vehicle Start
Remote Vehicle Start Your vehicle may have a remote starting feature that allows you to start the engine from outside the vehicle. It may also start the vehicle’s heating or air conditioning systems and rear window defogger. When the remote start system is active and the vehicle has an automatic climate control system, it will automatically regulate the inside temperature.
Page 83 After entering the vehicle during a remote start, insert and turn the key to ON/RUN to drive the vehicle. The engine will shut off automatically after 10 minutes, unless a time extension has been done or the vehicle’s key is inserted into the ignition switch and turned to ON/RUN.
Page 84: Remote Start Ready
• The engine coolant temperature is too high. • The oil pressure is low. • Two remote vehicle starts, or one start with a time extension, have already been provided for that ignition cycle. If a remote start is attempted and is unsuccessful, the Driver Information Center (DIC) will display REMOTE START DISABLED.
Page 85: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 86: Delayed Locking
Press the bottom of the switch to lock all doors. Press the top of the switch to unlock all doors. If the vehicle has the content theft-deterrent system, the vehicle is programmed to arm the system with the power door lock switch. If your vehicle has a Driver Information Center (DIC) this feature can be turned off.
Page 87: Lockout Protection
The rear door security locks are located on the inside edge of each rear door. You must open the rear doors to access them. To assist you in ﬁnding the lock, your vehicle will have one of the following: To use these locks, do the following: 1.
Page 88: Trunk
Trunk CAUTION: It can be dangerous to drive with the trunk lid open because carbon monoxide (CO) gas can come into your vehicle. You cannot see or smell CO. It can cause unconsciousness and even death. If you must drive with the trunk lid open or if electrical wiring or other cable connections must pass through the seal between the body and the trunk lid:...
Page 89 Remote Trunk Release This feature is used to unlock the trunk from inside the vehicle using the power door lock switch. Press and hold the top of the driver’s power door lock switch to unlock the trunk. The vehicle must be in PARK (P) to unlock the trunk. Emergency Trunk Release Handle Notice: Do not use the emergency trunk release handle as a tie-down or anchor point when securing...
Page 90 Trunk Lid Pull Down Handle and Tie-Down Features 2-16 Your vehicle has a trunk lid pull down handle (A) located on the inside of the trunk lid on the driver’s side of the vehicle. Use the handle to pull down the trunk lid when closing it.
Page 91: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 92: Power Windows
Power Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome from extreme heat in warm or hot weather and suffer permanent injuries or even death from heat stroke. Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed.
Page 93: Sun Visors
Express-Down Window The driver’s window switch has an express-down feature labeled AUTO. This lets you lower the window completely without holding the switch. Press the front of the switch to the second position and release. To stop the window while it is lowering, brieﬂy pull up on the switch.
Page 94: Theft-Deterrent Systems
Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Content Theft-Deterrent Your vehicle may have a content theft-deterrent alarm system.
Page 95: Disarming With Your Key
When the doors are locked using the power door lock switch of either front door, the red light, if your vehicle has one, will start ﬂashing at a fast rate, indicating that the system is arming. After all the doors are locked there will be a time delay and then the red light, if your vehicle has one, will begin to ﬂash at a very slow rate, indicating the system is armed.
Page 96: Pass-Key ® Iii
® PASS-Key ® Your PASS-Key III system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 97 If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the fuse. See Fuses and Circuit Breakers on page 5-109. If the engine still does not start with the other key, the vehicle needs service.
Page 98: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: • Do not drive at any one constant speed, fast or slow, for the ﬁrst 500 miles (805 km).
Page 99: Retained Accessory Power (Rap)
If the steering wheel is locked, move it from right to left and turn the key to ACC/ACCESSORY. If none of this works, then your vehicle needs service. B (ACC/ACCESSORY): This position lets the radio and windshield wipers operate while the engine is off. To use ACC/ACCESSORY, turn the key clockwise.
Page 100: Starting The Engine
Starting the Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine will not start in any other position – this is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Do not try to shift to PARK (P) if your vehicle is moving.
Page 101: Engine Coolant Heater
Notice: Cranking the engine for long periods of time, by returning the key to the START position immediately after cranking has ended, can overheat and damage the cranking motor, and drain the battery. Wait at least 15 seconds between each try, to let the cranking motor cool down.
Page 102: Active Fuel Management
To Use the Engine Coolant Heater 1. Turn off the engine. 2. Open the hood and unwrap the electrical cord. The cord is attached to the underside of the diagonal brace, which is located above the engine air cleaner/ﬁlter assembly. 3.
Page 103: Automatic Transmission Operation
Automatic Transmission Operation Your vehicle’s automatic transmission may have a shift lever on the steering column or on the console between the seats. Console Shift Lever There is also a display located on the instrument panel cluster that indicates the vehicle’s gear position.
Page 104 CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly.
Page 105 CAUTION: Shifting into a drive gear while the engine is running at high speed is dangerous. Unless your foot is ﬁrmly on the brake pedal, your vehicle could move very rapidly. You could lose control and hit people or objects. Do not shift into a drive gear while your engine is running at high speed.
Page 106: Parking Brake
Notice: Driving in SECOND (2) for more than 25 miles (40 km) or at speeds over 55 mph (90 km/h) may damage the transmission. Also, shifting into SECOND (2) at speeds above 65 mph (105 km/h) can cause damage. Drive in THIRD (3) or DRIVE (D) instead of SECOND (2).
Page 107: Shifting Into Park (P)
Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Make sure that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and parking on any hill, see Towing a Trailer on page 4-28.
Page 108: Console Shift Lever
Console Shift Lever If your vehicle is equipped with a console shift lever, use this procedure to shift the vehicle into PARK (P): 1. Hold the brake pedal down with your right foot. 2. Move the shift lever into PARK (P) by pushing the lever all the way toward the front of your vehicle and then to the left.
Page 109: Shifting Out Of Park (P)
Torque Lock If you are parking on a hill and you do not shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of PARK (P).
Page 110: Parking Over Things That Burn
Console Shift If your console shift lever cannot be moved out of PARK (P) 1. Apply and maintain the regular brakes. 2. Turn the ignition to ON/RUN position. See Ignition Positions on page 2-24 for more information. 3. Let up on the shift lever and make sure the shift lever is pushed all the way into PARK (P).
Page 111: Engine Exhaust
Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell. It can cause unconsciousness and death. You might have exhaust coming in if: • The exhaust system sounds strange or different.
Page 112: Mirrors
CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. Do not leave your vehicle when the engine is running unless you have to.
Page 113 ® There are also three OnStar buttons located at the bottom of the mirror. See your dealer/retailer for more information on the system and how to subscribe to ® ® OnStar . See OnStar System on page 2-43 for more information about the services OnStar Automatic Dimming Rearview Mirror While sitting in a comfortable driving position, adjust...
Page 114: Outside Power Mirrors
Outside Power Mirrors The controls for the outside power mirrors, are located on the driver’s door armrest. Move the selector switch located below the four-way control pad to the left or right to choose either the driver’s side or passenger’s side mirror. To adjust a mirror, use the arrows located on the four-way control pad to move the mirror in the desired direction.
Page 115: Object Detection Systems
Object Detection Systems Ultrasonic Rear Parking Assist (URPA) If your vehicle has the Ultrasonic Rear Parking Assist (URPA) system, it helps you park easier and avoid other vehicles while in REVERSE (R). It operates at speeds less than 3 mph (5 km/h). It can determine how close objects are to the rear bumper, up to 5 feet (1.5 m) behind your vehicle.
Page 116: How The System Works
How the System Works URPA comes on automatically when the shift lever is moved into REVERSE (R). The rear display will then brieﬂy illuminate to let you know the system is working. URPA operates only at speeds less than 3 mph (5 km/h).
Page 117: Onstar System
• A trailer was attached to your vehicle, or a bicycle or an object was hanging out of your trunk during your last drive cycle, the red light may illuminate. Once the attached object is removed, URPA will return to normal operation. •...
Page 118: Onstar Services
OnStar service is provided to you subject to the OnStar Terms and Conditions. You may cancel your OnStar service at any time by contacting OnStar. A complete OnStar Owner’s Guide and the OnStar Terms and Conditions are included in the vehicle’s OnStar Subscriber glove box literature.
Page 119: Onstar Virtual Advisor
Available Services with Safe & Sound Plan • Automatic Notiﬁcation of Airbag Deployment • Advanced Automatic Crash Notiﬁcation (AACN) (If equipped) • Link to Emergency Services • Roadside Assistance • Stolen Vehicle Location Assistance • AccidentAssist • Remote Door Unlock/Vehicle Alert •...
Page 120: Onstar Steering Wheel Controls
OnStar Steering Wheel Controls Your vehicle may have a Talk/Mute button that can be used to interact with OnStar Hands-Free Calling. See Audio Steering Wheel Controls on page 3-102 for more information. On some vehicles, you may have to hold the button for a few seconds and give the command “ONSTAR”...
Page 121: Universal Home Remote System
Your Responsibility Increase the radio volume if you cannot hear the OnStar advisor. If the light next to the OnStar buttons is red, this means that your system is not functioning properly and should be checked by your dealer/retailer. If the light appears clear (no light is appearing), your OnStar subscription has expired.
Page 122: Universal Home Remote System Operation
Universal Home Remote System Operation If there is one triangular Light Emitting Diode (LED) indicator light above the Universal Home Remote buttons, follow the instructions below. This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices.
Page 123: Programming The Universal Home Remote System
Programming the Universal Home Remote System If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www.homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before you begin. If you do not follow these actions, the device will time out and you will have to repeat the procedure.
Page 124 4. At the same time, press and hold both the Universal Home Remote button that you would like to use to control the garage door and the hand-held transmitter button. Do not release the Universal Home Remote button or the hand-held transmitter button until Step 4 has been completed.
Page 125: Gate Operator And Canadian Programming
9. Immediately return to the vehicle. Firmly press and hold the Universal Home Remote button, chosen in Step 3 to control the garage door, for two seconds, and then release it. If the garage door does not move, press and hold the same button a second time for two seconds, and then release it.
Page 126: Storage Areas
Erasing Universal Home Remote Buttons Erase the programmed buttons when you sell or terminate your lease. To erase all programmed buttons on the Universal Home Remote device: 1. Press and hold down the two outside buttons until the indicator light begins to ﬂash, after 20 seconds. 2.
Page 127: Center Console Storage
The cupholder has an arm that adjusts to two positions to ﬁt either a large cup or two smaller cups. If your vehicle is the six-passenger model, there is a cupholder located underneath the seat. To access, pull the center seat forward. The cupholder has a support that adjusts to two positions to ﬁt either a large cup or two smaller cups.
Page 128: Convenience Net
Convenience Net Your vehicle may have a convenience net in the rear of the vehicle. Store small loads as far forward as possible. The net should not be used to store heavy loads. Sunroof The vehicle may have a sunroof. It includes a sliding glass panel and a sunshade.
Page 129 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-6 Horn ...3-6 Tilt Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-8 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-8 Windshield Wipers ...3-9 Windshield Washer ...3-9 Cruise Control ...3-10 Exterior Lamps ...3-13 Daytime Running Lamps (DRL)/...
Page 130 Section 3 Low Coolant Warning Light ...3-41 Tire Pressure Light ...3-41 Malfunction Indicator Lamp ...3-42 Oil Pressure Light ...3-45 Change Engine Oil Light ...3-45 Security Light ...3-45 Cruise Control Light ...3-46 Reduced Engine Power Light ...3-46 Highbeam On Light ...3-46 Headlamps Suggested Light ...3-47 Low Washer Fluid Warning Light ...3-47 Door Ajar Light ...3-47...
Page 131 NOTES...
Page 132: Instrument Panel Overview
Instrument Panel Overview...
Page 133 The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-28. B. Interior Lamps Control. See Interior Lamps on page 3-16. C. Exterior Lamps Control. See Exterior Lamps on page 3-13. Fog Lamp Control. See Fog Lamps on page 3-15.
Page 134: Hazard Warning Flashers
Hazard Warning Flashers The hazard warning ﬂashers let you warn the police and others that you have a problem. The front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is on the instrument panel. Press the button to make the front and rear turn signal lamps ﬂash on and off.
Page 135: Turn Signal/Multifunction Lever
Telescoping Column If the vehicle has a telescoping column on the steering wheel it adjusts the distance of the steering wheel to the driver without having to move the driver’s seat. The lever that makes this adjustment is located on the left side of the steering column and behind the tilt lever, if the vehicle has...
Page 136: Turn And Lane-Change Signals
Turn and Lane-Change Signals To signal a turn, move the lever up or down. The lever returns to its original position when the turn is completed. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change.
Page 137: Windshield Wipers
Windshield Wipers Clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, gently loosen or thaw them. Damaged wiper blades may not clear the windshield well, making it harder to see and drive safely. If the blades do become damaged, install new blades or blade inserts.
Page 138: Cruise Control
Cruise Control With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This can really help on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h).
Page 139 Setting Cruise Control Cruise control will not work if the parking brake is set, or if the master cylinder brake ﬂuid level is low. The cruise control light on the instrument panel cluster comes on after the cruise control has been set to the desired speed.
Page 140 Reducing Speed While Using Cruise Control To reduce your speed while using cruise control: • Press and hold the SET– button on the steering wheel until you reach the desired lower speed, then release it. • To slow down in very small amounts, press the SET–...
Page 141: Exterior Lamps
Exterior Lamps The control located to the left of the cluster on the instrument panel, operates the exterior lamps. It controls the following systems: • Headlamps • Taillamps • Parking Lamps • License Plate Lamps • Instrument Panel Lights • Fog Lamps (If Equipped) The exterior lamps control has four positions: (On/Off): Brieﬂy turn the control to this position to...
Page 142: Daytime Running Lamps (Drl)/ Automatic Headlamp System
(Headlamps): Turn the control to this position to turn on the headlamps together with the following lamps listed below. A warning chime will sound if the driver’s door is opened when the ignition switch is turned to LOCK/OFF or ACC/ACCESSORY and the headlamps or parking lamps are on.
Page 143: Fog Lamps
When it is dark enough outside, the DRL will turn off and the vehicle’s headlamps and parking lamps will turn on. The other lamps that come on with the headlamps will also come on. When it is bright enough outside, the headlamps will go off and the DRL will come on.
Page 144: Interior Lamps
Interior Lamps Your interior lamps control is located next to the exterior lamps control and to the left of the steering wheel on the instrument panel. (Off): Turn the control to this position to disable courtesy lamps, entry lighting, delayed entry lighting, and delayed exit lighting.
Page 145: Delayed Entry Lighting
Delayed Entry Lighting Delayed entry lighting lights the vehicle’s interior for a period of time after all the doors have been closed. After all the doors have been closed, the delayed entry lighting feature will continue to work until one of the following occurs: •...
Page 146: Overhead Console Reading Lamps
Overhead Console Reading Lamps Your vehicle may have reading lamps located on the overhead console. Press the lens to turn them on and off. Rear Assist Handle Reading Lamps Your vehicle may have reading lamps located near the rear assist handles. Press the lens to turn them on and off.
Page 147: Battery Run-Down Protection
Battery Run-Down Protection This helps prevent the vehicle’s battery from draining in case the interior courtesy lamps, reading lamps, trunk lamp, underhood lamp, glove box lamps, or sun visor vanity lamps, if equipped, are accidently left on. If any of these lamps are left on while the ignition is off, they will automatically turn off after 10 minutes.
Page 148: Ashtray(S) And Cigarette Lighter
Ashtray(s) and Cigarette Lighter Your vehicle may have a removable ashtray and cigarette lighter. The cigarette lighter may be located under the climate control system. The removable ashtray can be placed into the front console cupholder. Notice: If you put papers, pins, or other ﬂammable items in the ashtray, hot cigarettes or other smoking materials could ignite them and possibly damage your vehicle.
Page 149 Operation OFF: Turn the left knob to this position to turn the climate control system off. (Fan): Turn the knob by this symbol, located on the left side of the climate control panel, clockwise or counterclockwise to increase or decrease the fan speed.
Page 150: Defogging And Defrosting
You can also select modes by using the following buttons: (Recirculate): Press this button to recirculate cabin air through the vehicle. It can be used to help reduce the outside air and odors that enter your vehicle or to help heat or cool the air inside your vehicle quicker.
Page 151: Rear Window Defogger
Turn the right knob to select the defog or defrost mode. Do not drive the vehicle until all windows are clear. (Defog): This mode directs half of the air to the windshield and the side window outlets and half to the ﬂoor outlets.
Page 152: Dual Automatic Climate Control System
Dual Automatic Climate Control System With this system you can control the heating, cooling, and ventilation for the vehicle. Automatic Operation AUTO (Automatic): Press the AUTO button for automatic control of the inside temperature, the air delivery mode, and the fan speed. There might be a delay of two to three minutes before the fan comes on when the automatic operation is used in cold weather.
Page 153: Manual Operation
4. Press OFF to turn the climate control system off. Only the rear defog and heated seats will function. Press AUTO or any other button except the heated seats or rear defog to turn the climate control system back on. This control has four types of operation.
Page 154 (Fan): Press this button to increase the fan speed. Pressing the arrows cancels the automatic operation and places the system in manual or semi-automatic mode. Press the AUTO button to return to automatic operation. If the airﬂow seems low when the fan is at the highest setting, the passenger compartment air ﬁlter may need to be replaced.
Page 155 Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog or frost from your windshield.
Page 156: Outlet Adjustment
Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window. The rear window defogger will only work when the engine is running. (Rear Window Defogger): Press this button to turn the rear window defogger on and off. Be sure to clear as much snow from the rear window as possible.
Page 157: Passenger Compartment Air Filter
Passenger Compartment Air Filter The passenger compartment air ﬁlter is located in the engine compartment below the air inlet grille, near the passenger’s side windshield wiper arm. See Engine Compartment Overview on page 5-12. The ﬁlter traps most of the pollen from the air entering the air conditioning module.
Page 158: Warning Lights, Gages, And Indicators
9. Remove the old air ﬁlter. 10. Install a new passenger compartment air ﬁlter. See Maintenance Replacement Parts on page 6-13 for the type of ﬁlter to use. Make sure it slides under the compartment retainers. 11. Reverse Steps 1 through 8. For best climate control performance, re-installation of a clean air ﬁlter is required.
Page 159: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster is designed to let the driver know at a glance how the vehicle is running. It will show how fast the vehicle is going, about how much fuel is in the fuel tank and many other things needed to drive safely and economically.
Page 160: Speedometer And Odometer
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your vehicle’s odometer works together with the driver information center. You can set a Trip A and Trip B odometer.
Page 161: Airbag Readiness Light
Passenger Safety Belt Reminder Light Several seconds after the engine is started, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled. See Passenger Sensing System on page 1-62 for more information.
Page 162: Passenger Airbag Status Indicator
If the airbag readiness light stays on after you start the vehicle or comes on when you are driving, your airbag system may not work properly. Have your vehicle serviced right away. CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly.
Page 163 CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag. A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s airbag inﬂates.
Page 164: Charging System Light
If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. CAUTION: If the airbag readiness light in the instrument panel cluster ever comes on and stays on, it means that something may be wrong with the airbag system.
Page 165: Brake System Warning Light
Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on and the parking brake is not applied, there is a brake problem.
Page 166: Antilock Brake System
Antilock Brake System Warning Light For vehicles with the Antilock Brake System (ABS), this light comes on brieﬂy when the engine is started. That is normal. If the light does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem.
Page 167: Enhanced Traction System
The TCS warning light will come on brieﬂy when the engine is started. If it does not come on then, have it ﬁxed so it will be ready to warn you if there is a problem. This light will also come on when the traction control button is pressed disabling the system.
Page 168: Engine Coolant Temperature Warning Light
Engine Coolant Temperature Warning Light The engine coolant temperature warning light will come on when the engine has overheated. If this happens you should pull over and turn off the engine as soon as possible. See Engine Overheating on page 5-30 for more information. Notice: Driving with the engine coolant temperature warning light on could cause your vehicle to overheat.
Page 169: Low Coolant Warning Light
Low Coolant Warning Light If your vehicle has this light, it comes on brieﬂy when you turn your ignition on as a bulb check only. Tire Pressure Light Your vehicle has a tire pressure light. This light comes on brieﬂy when the engine is started and provides information about tire pressures and the Tire Pressure Monitoring System.
Page 170: Malfunction Indicator Lamp
Malfunction Indicator Lamp Check Engine Light A computer system called OBD II (On-Board Diagnostics-Second Generation) monitors operation of the fuel, ignition, and emission control systems. It makes sure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The check engine light comes on to indicate that there is an OBD II...
Page 171: If The Light Is On Steady
This light comes on, as a check to show it is working, when the ignition is turned ON/RUN but the engine is not running. If the light does not come on, have it repaired. This light also comes on during a malfunction in one of two ways: •...
Page 172: Emissions Inspection And Maintenance Programs
Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5. Poor fuel quality causes the engine not to run as efficiently as designed. You might notice this as stalling after start-up, stalling when you put the vehicle into gear, misﬁring, hesitation on acceleration, or stumbling on acceleration —...
Page 173: Maintenance Schedule
Oil Pressure Light CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre. You or others could be burned. Check your oil as soon as possible and have your vehicle serviced.
Page 174: Cruise Control Light
Cruise Control Light This light comes on whenever you set the cruise control. The light goes out when the cruise control is turned off. See Cruise Control on page 3-10 for more information. Reduced Engine Power Light If the reduced engine power light is on, a chime will sound and a noticeable reduction in the...
Page 175: Headlamps Suggested Light
Headlamps Suggested Light This light will come on when the use of headlamps is suggested. Low Washer Fluid Warning Light This light will come on brieﬂy when the ignition is on. If the light stays on, a chime will sound indicating your windshield washer ﬂuid is low.
Page 176: Service Vehicle Soon Light
Service Vehicle Soon Light For vehicles with this light, it will come on if a condition exists that may require the vehicle to be taken in for service. If the light comes on, see your dealer/retailer for service as soon as possible. Fuel Gage The fuel gage indicates about how much fuel is left...
Page 177: Check Gas Cap Light
Check Gas Cap Light If your vehicle has this light, it will come on if your gas cap is not securely fastened. See Malfunction Indicator Lamp on page 3-42 for more information. Driver Information Center (DIC) Your vehicle may have a Driver Information Center (DIC). All messages will appear in the DIC display located in the instrument panel cluster, below the speedometer.
Page 178: Dic Operation And Displays
DIC Operation and Displays The DIC has different modes which can be accessed by pressing the DIC buttons located on the center of the instrument panel. Depending on whether your vehicle has the base level or uplevel DIC, the buttons and modes available will differ.
Page 179 (Gages)*: Press this button to display the battery voltage, oil life, and tire pressure readings. (Set/Reset)*: Press this button to set or reset certain functions and to turn off or acknowledge messages on the DIC. (Option)*: Press this button to display the units, language, personalization, compass zone, and compass calibration.
Page 180 There is also a retroactive trip odometer function that performs the following for each trip odometer: • If the vehicle’s speed has exceeded 3 mph (5 km/h) during the current ignition cycle, this function will set the trip odometer to the distance driven during the current ignition cycle.
Page 181: Average Fuel Economy
Fuel Menu Items (Uplevel Only) (Fuel): Press this button to scroll through the following menu items: Fuel Range Press the fuel button until FUEL RANGE displays. This mode shows the approximate number of remaining miles or kilometers the vehicle can be driven without refueling.
Page 182: Tire Pressure
Oil Life Press the gages button until OIL LIFE displays. This mode shows an estimate of the oil’s remaining useful life. If you see OIL LIFE 99% on the display, that means 99% of the current oil life remains. The engine oil life system will alert you to change your oil on a schedule consistent with your driving conditions.
Page 183: Compass Calibration
Option Menu Items (Uplevel Only) (Option): Press this button to scroll through the following menu items: Units Press the option button until UNITS displays. This mode allows you to select between English or Metric units of measurement. Once in this mode, press the set/reset button to select between ENGLISH or METRIC units.
Page 184: Dic Compass (Uplevel Only)
DIC Compass (Uplevel Only) Your vehicle may have a compass in the Driver Information Center (DIC). Compass Zone The zone is set to zone eight upon leaving the factory. Your dealer/retailer will set the correct zone for your location. Under certain circumstances, such as during a long distance cross-country trip or moving to a new state or province, it will be necessary to compensate for compass variance by resetting the zone through the...
Page 185 3. Press the set/reset button to scroll through and select the appropriate variance zone. 4. Press the trip or fuel button until the vehicle heading, for example, N for North, is displayed in the DIC. 5. If calibration is necessary, calibrate the compass. See “Compass Calibration Procedure”...
Page 186: Dic Warnings And Messages
DIC Warnings and Messages Messages are displayed on the uplevel DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another.
Page 187: Battery Saver Active
BATTERY SAVER ACTIVE This message displays when the system detects that the battery voltage is dropping beyond a reasonable level. The battery saver system starts reducing certain features of the vehicle that you may be able to notice. At the point that the features are disabled, this message is displayed.
Page 188: Check Gas Cap
This message continues to display for two seconds if it has not been acknowledged when the engine is turned off. It also re-displays for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message re-appears when the engine is turned on.
Page 189: Delayed Locking
This message displays while the ignition is in ON/RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen. This message continues to display for two seconds if it has not been acknowledged when the engine is turned off.
Page 190: Engine Coolant Hot
DRIVER’S REAR DOOR AJAR This message displays when the driver side rear door is not closed properly. Make sure that the door is closed completely. This message displays while the ignition is in ON/RUN. A chime sounds when the gear position is shifted out of PARK (P).
Page 191: Hood Ajar
HEADLAMPS SUGGESTED This message displays when the amount of available light outside of the vehicle is low, or the windshield wipers have been on for about 30 seconds, and the exterior lamps control is off or in the parking lamps position.
Page 192: Key In Ignition
KEY FOB BATTERY LOW This message displays when the battery in the Remote Keyless Entry (RKE) transmitter needs to be replaced. To replace the battery, see “Battery Replacement” under Remote Keyless Entry (RKE) System Operation on page 2-5. This message displays while the ignition is in ON/RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen.
Page 193: Low Fuel
This message continues to display for two seconds if it has not been acknowledged when the engine is turned off. It also re-displays for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message re-appears when the engine is turned on.
Page 194: Low Washer Fluid
LOW OIL PRESSURE Notice: If the LOW OIL PRESSURE warning message appears on the DIC display, stop the vehicle immediately. Do not drive the vehicle until the cause of the low oil pressure is corrected. Severe engine damage can result from driving a vehicle with low oil pressure.
Page 195: Parking Brake On
PARKING BRAKE ON This message displays to alert the driver when the vehicle’s parking brake is on, the ignition is in ON/RUN, and the vehicle speed is greater than 5 mph (8 km/h). Release the parking brake before driving. See Parking Brake on page 2-32 for more information.
Page 196: Reduced Engine Power
PASSENGER’S REAR DOOR AJAR This message displays when the passenger side rear door is not closed properly. Make sure that the door is closed completely. This message displays while the ignition is in ON/RUN. A chime sounds when the gear position is shifted out of PARK (P).
Page 197 This message continues to display for two seconds if it has not been acknowledged when the engine is turned off. It also re-displays for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message re-appears when the engine is turned on.
Page 198: Service Brake System
RIGHT REAR TURN LAMP OUT This message displays when the right rear turn signal bulb needs to be replaced. See Taillamps, Turn Signal, Sidemarker, Stoplamps and Back-up Lamps on page 5-59. This message displays while the ignition is in ON/RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen.
Page 199 This message continues to display for two seconds if it has not been acknowledged when the engine is turned off. It also re-displays for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message re-appears when the engine is turned on.
Page 200: Service Theft System
SERVICE THEFT SYSTEM This message displays when there is a problem with the theft-deterrent system programmed in the key. A fault has been detected in the system which means that the system is disabled and it is not protecting the vehicle.
Page 201 SERVICE TRACTION SYSTEM This message displays when the traction system is not functioning properly. A warning light also appears on the instrument panel cluster. See Traction Control System (TCS) Warning Light on page 3-38. See Traction Control System (TCS) on page 4-6 or Enhanced Traction System (ETS) on page 4-7 for more information.
Page 202: Service Vehicle Soon
SERVICE VEHICLE SOON This message displays when a non-emissions related malfunction occurs. Have the vehicle serviced by your dealer/retailer as soon as possible. This message displays only while the ignition is in ON/RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen.
Page 203 STARTING DISABLED This message displays if the starting of the engine is disabled due to the electronic throttle control system or vehicle theft-deterrent system. Have your vehicle serviced by your dealer/retailer immediately. This message only appears while the ignition is in ON/RUN and will not disappear until the problem is resolved.
Page 204: Dic Vehicle Personalization
TRUNK AJAR This message displays when the trunk is not closed completely. Make sure that the trunk is closed completely. See Trunk on page 2-14. This message displays while the ignition is in ON/RUN. A chime sounds when the gear position is shifted out of PARK (P).
Page 205 All of the customization and personalization options may not be available on your vehicle. Only the options available will be displayed on the DIC. The default settings for the customization and personalization features were set when your vehicle left the factory, but may have been changed from their default state since then.
Page 206 ALL KEYS WILL BE RESET This screen will only display if YES was selected on the FACTORY DEFAULTS screen. Press the set/reset button to scroll through the following settings: CANCEL (default): The features will not be set to their factory default settings and the DIC will return to the PERSONAL PROGRAM menu.
Page 207 DELAYED LOCKING This feature allows the locking of the vehicle to be delayed until all of the doors have been closed for about ﬁve seconds. When the delayed locking feature is enabled, it may be activated when the key is out of the ignition by doing one of the following: •...
Page 208 CONTENT THEFT If your vehicle has the content theft-deterrent system, once this feature is turned on, the system will activate if someone tries to enter the vehicle without using the Remote Keyless Entry (RKE) transmitter or the correct key. Press the option button until CONTENT THEFT appears on the DIC display.
Page 209: Remote Start
REMOTE START If your vehicle has remote start, this feature allows the remote start to be turned off or on. The remote start feature allows you to start the engine from outside of the vehicle using the Remote Keyless Entry (RKE) transmitter.
Page 210 REPLACE KEY This screen displays only if YES was selected for the PERSONALIZE KEY feature, keys 1 and 2 have already been personalized, and the current key being used is not key 1 or 2. This feature allows you to program a key to be recognized as key 1 or 2 in the event that the previously programmed key needs to be replaced.
Page 211 AUTO UNLOCK ON This feature displays only if DRIVER or ALL was selected for the AUTO DOOR UNLOCK feature. This feature allows the selection of when the vehicle’s doors will unlock. Press the option button until AUTO UNLOCK ON appears on the DIC display. Press the set/reset button to scroll through the following settings: KEY-OUT: The door(s) will unlock when the key is taken out of the ignition.
Page 212: Audio System(S)
Audio System(s) Determine which radio your vehicle has and then read the pages following to familiarize yourself with its features. CAUTION: This system provides you with far greater access to audio stations and song listings. Giving extended attention to entertainment tasks while driving can cause a crash and you or others can be injured or killed.
Page 213: Setting The Clock
Notice: Before adding any sound equipment to your vehicle, such as an audio system, CD player, CB radio, mobile telephone, or two-way radio, make sure that it can be added by checking with your dealer/retailer. Also, check federal rules covering mobile radio and telephone units.
Page 214 Radio(s) Radio with CD (MP3) shown, Radio with CD similar 3-86 Radio with Six-Disc CD Your vehicle has one of these radios as its audio system.
Page 215: Playing The Radio
Playing the Radio (Power): Press to turn the system on and off. (Volume): Turn to increase or to decrease the volume. DISP (Display): Press to switch the display between the radio station frequency and time of day. While the ignition is off, press this button to display the time. If your vehicle’s radio has XM™...
Page 216: Setting Preset Stations
To scan preset stations, press and hold either arrow for more than four seconds. PSCAN or PSC displays and the radio beeps twice. The radio goes to a preset station, plays for a few seconds, then goes to the next preset station. Press either arrow again or one of the pushbuttons to stop scanning presets.
Page 217 To adjust all tone and speaker controls to the middle position, press and hold when no tone or speaker control displays. ALL CENTERED displays and the radio beeps once. EQ (Equalization): Press to select customized equalization settings. To return the bass and treble to the manual mode, press and release until BASS or TREBLE displays.
Page 218: Radio Messages
Scanning Categories (CAT) (XM™ Satellite Radio Service Only) To scan a desired category by doing the following: 1. Press the CAT button to enter the category select mode. The current category displays. 2. Turn the knob to select a category. 3.
Page 219: Playing A Cd
Playing a CD Insert a CD partway into the slot, label side up. The player pulls it in and the CD begins playing. To insert a CD while the ignition is off, ﬁrst press the or the DISP knob. If the ignition or radio is turned off while a CD is in the player, it stays in the player.
Page 220 For vehicles that have a radio with a Six-Disc CD player, see the following: LOAD: Press to load CDs into the CD player. This CD player holds up to six CDs. To insert one CD: 1. Turn the ignition on. 2.
Page 221 To eject multiple CDs, do the following: 1. Press and hold this button for two seconds. The radio beeps once and the indicator light, located to the right of the slot, begins to ﬂash and EJECT ALL displays. 2. Once the light stops ﬂashing, REMOVE CD # displays.
Page 222 4 RDM (Random): Depending on the radio, press to hear the tracks in random, rather than sequential, order. RANDOM ON displays. Press again to turn off random play. For the radio with a Six-Disc CD player, press to listen to the tracks in random, on one CD or on all of the CDs.
Page 223 BAND: Press to listen to the radio while a CD is playing. The inactive CD remains inside the radio for future listening. CD: Press to play a CD while listening to the radio. The CD symbol displays when a CD is loaded. EQ (Equalization): Press to select an equalization setting while playing a CD.
Page 224 To play the song list, press the LIST button. One beep sounds and S-LIST displays. The recorded tracks begins to play in the order they were saved. Seek through the song list by using the SEEK arrows. Seeking past the last saved track returns to the ﬁrst saved track.
Page 225: Using An Mp
CD Messages CHECK CD: If this message displays and/or the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road. When the road becomes smoother, the CD should play.
Page 226 The player is able to read and play a maximum of 50 folders, 50 playlists, 10 sessions, and 255 ﬁles. Long ﬁle names, folder names, or playlist names could use more disc memory space than necessary. To conserve disc space, keep the length of the ﬁle, folder, or playlist name brief.
Page 227 File System and Naming The song name that displays is the song name that is contained in the ID3 tag. If the song name is not present in the ID3 tag, then the radio displays the ﬁle name without the extension (such as .mp3) as the track name. Track names longer than 32 characters or four pages are shortened.
Page 228: Xm Radio Messages
(Previous Folder): Press this button to go to the ﬁrst track in the previous folder. Press this button while in random folder mode to go to the previous folder and randomly play the tracks in that folder. (Next Folder): Press this button to go to the ﬁrst track in the next folder.
Page 229: Theft-Deterrent Feature
No Signal: The vehicle is in a location that is blocking the XM™ signal. When the vehicle is moved into an open area, the signal should return. Loading XM: The radio is processing audio and text data received. No action is needed. This message should disappear shortly.
Page 230: Audio Steering Wheel Controls
Audio Steering Wheel Controls If your vehicle has this feature, some audio controls can be adjusted at the steering wheel. They include the following: (Seek): Press the seek arrows to go to the next or to the previous radio station. The radio seeks stations only with a strong signal that are in the selected band.
Page 231: Radio Reception
Radio Reception Frequency interference and static during normal radio reception can occur if items such as cellphone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Page 232: Backglass Antenna
Backglass Antenna The AM-FM antenna is integrated with the rear window defogger, located in the rear window. Make sure that the inside surface of the rear window is not scratched and that the lines on the glass are not damaged. If the inside surface is damaged, it could interfere with radio reception.
Page 233: Xm™ Satellite Radio Antenna System
XM™ Satellite Radio Antenna System The XM™ Satellite Radio antenna is located on the roof of your vehicle. Keep this antenna clear of snow and ice build up for clear radio reception. If your vehicle has a sunroof, the performance of the XM™...
Page 234 NOTES 3-106...
Page 235: Driving Your Vehicle
Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Defensive Driving ...4-2 Drunk Driving ...4-2 Control of a Vehicle ...4-3 Braking ...4-3 Antilock Brake System (ABS) ...4-4 Braking in Emergencies ...4-5 Traction Control System (TCS) ...4-6 Enhanced Traction System (ETS) ...4-7 ®...
Page 236: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving Defensive driving means “always expect the unexpected.” The ﬁrst step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 1-9. CAUTION: Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes.
Page 237: Control Of A Vehicle
Alcohol affects four things that anyone needs to drive a vehicle: judgment, muscular coordination, vision, and attentiveness. Police records show that almost 40 percent of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving.
Page 238: Antilock Brake System (Abs)
Average reaction time is about three-fourths of a second. But that is only an average. It might be less with one driver and as long as two or three seconds or more with another. Age, physical condition, alertness, coordination, and eyesight all play a part. So do alcohol, drugs, and frustration.
Page 239: Braking In Emergencies
If there is a problem with ABS, this warning light will stay on. See Antilock Brake System Warning Light on page 3-38. Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking.
Page 240: Traction Control System (Tcs)
Traction Control System (TCS) Your vehicle may have a Traction Control System (TCS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that one or both of the front wheels are spinning or beginning to lose traction.
Page 241: Enhanced Traction System (Ets)
When the TCS is turned off, the TCS warning light will come on along with the TRACTION CONTROL OFF message on the DIC. It will disappear when the TCS is turned back on. If the TCS is limiting wheel spin when the TCS button is pressed, the TCS warning light will come on and the TCS will turn off right away.
Page 242: Stabilitrak System
To limit wheel spin, especially in slippery road conditions, you should always leave the ETS on. But you can turn the system off if you ever need to. The ETS should be turned off if the vehicle ever gets stuck in sand, mud or snow and rocking the vehicle is required To turn the ETS on or off, press the Traction Control button located above the radio.
Page 243: Steering
Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort. Steering Tips It is important to take curves at a reasonable speed. A lot of the “driver lost control”...
Page 244: Steering In Emergencies
Try to adjust your speed so you can drive through the curve. Maintain a reasonable, steady speed. Wait to accelerate until you are out of the curve, and then accelerate gently into the straightaway. Adding non-dealer/non-retailer accessories can affect your vehicle’s performance. See Accessories and Modiﬁcations on page 5-3.
Page 245: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your vehicle’s right wheels have dropped off the edge of a road onto the shoulder while you are driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 246: Loss Of Control
Loss of Control Let us review what driving experts say about what happens when the three control systems — brakes, steering, and acceleration — do not have enough friction where the tires meet the road to do what the driver has asked.
Page 247: Driving At Night
While driving on a surface with reduced traction, try your best to avoid sudden steering, acceleration, or braking, including reducing vehicle speed by shifting to a lower gear. Any sudden changes could cause the tires to slide. You may not realize the surface is slippery until your vehicle is skidding.
Page 248: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep-standing or ﬂowing water. CAUTION: Wet brakes can cause crashes.
Page 249: Before Leaving On A Long Trip
Before Leaving on a Long Trip To prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: • Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? •...
Page 250: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on ﬂat or rolling terrain. Tips for driving in these conditions include: • Keep your vehicle serviced and in good shape. • Check all ﬂuid levels and brakes, tires, cooling system, and transmission.
Page 251: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You might want to put winter emergency supplies in your trunk. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and a couple of reﬂective warning triangles.
Page 252: If You Are Caught In A Blizzard
A traction system improves your ability to accelerate when driving on a slippery road. Even though you have a traction system, slow down and adjust your driving to the road conditions. Under certain conditions, you might want to turn the traction system off, such as when driving through deep snow and loose gravel, to help maintain vehicle motion at lower speeds.
Page 253 You can run the engine to keep warm, but be careful. CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Page 254: If Your Vehicle Is Stuck In Sand, Mud, Ice
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
Page 255: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out First, turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. See Traction Control System (TCS) on page 4-6, Enhanced Traction System (ETS) on page 4-7, ®...
Page 256 Tire and Loading Information Label Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). 4-22 The Tire and Loading Information label lists the number of occupant seating positions (A), and the...
Page 257 Steps for Determining Correct Load Limit Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Page 258 Example 1 Item Description Maximum Vehicle Capacity Weight for Example 1 Subtract Occupant Weight 150 lbs (68 kg) Available Occupant and Cargo Weight 4-24 Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs (317 kg) Example 2 Description Maximum Vehicle 1,000 lbs...
Page 259 Example 3 Item Description Maximum Vehicle Capacity Weight for Example 3 Subtract Occupant Weight 200 lbs (91 kg) Available Cargo Weight Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s maximum vehicle capacity weight and seating positions.
Page 260 Never exceed the GVWR for your vehicle or the Gross Axle Weight Rating (GAWR) for either the front or rear axle. If the vehicle is going to carry a heavy load, spread it out. See “Steps for Determining Correct Load Limit” earlier in this section. CAUTION: Do not load your vehicle any heavier than the Gross Vehicle Weight Rating (GVWR),...
Page 261: Towing
Towing Towing Your Vehicle Consult your dealer/retailer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Assistance Program on page 7-8. If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see “Recreational Vehicle Towing”...
Page 262: Towing A Trailer
Dolly Towing Your vehicle can be towed using a dolly. To tow your vehicle using a dolly: 1. Put the front wheels on a dolly. 2. Put the gear shift lever in PARK (P). 3. Set the parking brake and then remove the ignition key.
Page 263: If You Do Decide To Pull A Trailer
Trailering means changes in handling, acceleration, braking, durability, and fuel economy. Successful, safe trailering takes correct equipment, and it has to be used properly. That is the reason for this part. In it are many time-tested, important trailering tips and safety rules. Many of these are important for your safety and that of your passengers.
Page 264: Weight Of The Trailer
Weight of the Trailer How heavy can a trailer safely be? It should never weigh more than 1,000 lbs (450 kg). But even that can be too heavy. It depends on how you plan to use your rig. For example, speed, altitude, road grades, outside temperature and how much the vehicle is used to pull a trailer are all important.
Page 265: Safety Chains
When using a weight-carrying hitch, the trailer tongue (A) should weigh 10 percent to 15 percent of the total loaded trailer weight (B). After the trailer is loaded, weigh the trailer and the tongue, separately, to see if the weights are proper. The correct weight could be achieved simply by moving some items around in the trailer.
Page 266: Driving With A Trailer
Trailer Brakes Does your trailer have its own brakes? Be sure to read and follow the instructions for the trailer brakes so you’ll be able to install, adjust and maintain them properly. • If your vehicle has antilock brakes, do not try to tap into your vehicle’s brake system.
Page 267: Following Distance
Following Distance Stay at least twice as far behind the vehicle ahead as when driving the vehicle without a trailer. This can help avoid situations that require heavy braking and sudden turns. Passing More passing distance is needed up ahead when towing a trailer.
Page 268: Driving On Grades
Driving On Grades Reduce speed and shift to a lower gear before starting down a long hill or steep downgrade. If the vehicle is not shifted down, the brakes might have to be used so much that they would get hot and no longer work well. On a long uphill grade, shift down and reduce the vehicle’s speed to around 45 mph (70 km/h) to reduce the possibility of engine and transmission overheating.
Page 269: Maintenance When Trailer Towing
When You Are Ready to Leave After Parking on a Hill 1. Apply the regular brakes and hold the pedal down while you: • Start the engine. • Shift into a gear. • Release the parking brake. 2. Let up on the brake pedal. 3.
Page 270 NOTES 4-36...
Page 271: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-3 California Perchlorate Materials Requirements ...5-4 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of Your Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-6 California Fuel ...5-6 Additives ...5-7 Fuels in Foreign Countries ...5-7...
Page 272 Section 5 Tire Inspection and Rotation ...5-75 When It Is Time for New Tires ...5-77 Buying New Tires ...5-78 Different Size Tires and Wheels ...5-80 Uniform Tire Quality Grading ...5-80 Wheel Alignment and Tire Balance ...5-82 Wheel Replacement ...5-82 Tire Chains ...5-84 If a Tire Goes Flat ...5-86 Changing a Flat Tire ...5-87 Removing the Spare Tire and Tools ...5-88...
Page 273: Service
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added to your vehicle they can affect your vehicle’s performance and safety, including such things as, airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like...
Page 274: California Perchlorate Materials Requirements
California Perchlorate Materials Requirements Certain types of automotive applications, such as airbag initiators, seat belt pretensioners, and lithium batteries contained in remote keyless entry transmitters, may contain perchlorate materials. Special handling may be necessary. For additional information, see www.dtsc.ca.gov/hazardouswaste/perchlorate. Doing Your Own Service Work CAUTION: You can be injured and your vehicle could be damaged if you try to do service work on a...
Page 275: Adding Equipment To The Outside Of
Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airﬂow around it. This can cause wind noise and can affect fuel economy and windshield washer performance. Check with your dealer/retailer before adding equipment to the outside of your vehicle.
Page 276: Gasoline Speciﬁcations
If your vehicle has the 5.3L V8 engine (VIN Code C), use premium unleaded gasoline with a posted octane rating of 91 or higher. You can also use regular unleaded gasoline rated at 87 octane or higher, but your vehicle’s acceleration could be slightly reduced, and you might notice a slight audible knocking noise, commonly referred to as spark knock.
Page 277: Additives
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly. In most cases, you should not have to add anything to the fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S.
Page 278: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 279 CAUTION: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop.
Page 280: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: •...
Page 281: Hood Release
Hood Release To open the hood, do the following: 1. Pull the interior hood release handle with this symbol on it. It is located to the left of the steering column below the instrument panel. 2. Push the secondary hood release lever, located under the center of the hood above the grille, up and to the right to disengage it.
Page 282: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 3.6L V6 engine, this is what you will see: 5-12...
Page 283 A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-44. B. Battery. See Battery on page 5-49. C. Remote Positive (+) Terminal. See Jump Starting on page 5-50. D. Underhood Fuse Block. See Underhood Fuse Block on page 5-112.
Page 284 When you open the hood on the 3.8L V6 engine, this is what you will see: 5-14...
Page 285 A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-44. B. Battery. See Battery on page 5-49. C. Remote Positive (+) Terminal. See Jump Starting on page 5-50. D. Passenger Compartment Air Filter. See Passenger Compartment Air Filter on page 3-29.
Page 286 When you open the hood on the 5.3L V8 engine, here is what you will see: 5-16...
Page 287 A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-44. B. Battery. See Battery on page 5-49. C. Underhood Fuse Block. See Underhood Fuse Block on page 5-112. D. Remote Positive (+) Terminal. See Jump Starting on page 5-50.
Page 288: Engine Oil
Engine Oil Checking Engine Oil It is a good idea to check the engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop.
Page 289 5.3L V8 Engine If the oil is below the cross-hatched area at the tip of the dipstick, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 5-116.
Page 290: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Look for three things: • GM6094M Your vehicle’s engine requires oil meeting GM Standard GM6094M. Look for and use only an oil that meets GM Standard GM6094M. • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle.
Page 291: Engine Oil Additives
Engine Oil Additives Do not add anything to the oil. The recommended oils with the starburst symbol that meet GM Standard GM6094M are all you need for good performance and engine protection. Engine Oil Life System When to Change Engine Oil Your vehicle has a computer system that lets you know when to change the engine oil and ﬁlter.
Page 292: How To Reset The Engine Oil Life System
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change the engine oil and ﬁlter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change the oil prior to a change engine oil light or CHANGE OIL SOON message being turned on, reset the system.
Page 293: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter The engine air cleaner/ﬁlter is located in the engine compartment on the driver’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at the Maintenance II intervals and replace it at the ﬁrst oil change after each 50,000 mile (80 000 km) interval.
Page 294 5.3L V8 Engine 1. Lift the ﬁlter cover tabs on top of the engine air cleaner/ﬁlter housing. 2. Push the ﬁlter cover housing toward the engine. 3. Pull out the ﬁlter. 4. Inspect or replace the engine air cleaner/ﬁlter. 5-24 5.
Page 295: Automatic Transmission Fluid
Automatic Transmission Fluid When to Check and Change Automatic Transmission Fluid A good time to check the automatic transmission ﬂuid level is when the engine oil is changed. Change the ﬂuid and ﬁlter at the intervals listed in Additional Required Services on page 6-6, and be sure to use the transmission ﬂuid listed in Recommended Fluids and Lubricants on page 6-12.
Page 296: Checking The Fluid Level
Checking the Fluid Level Prepare the vehicle as follows: 1. Park the vehicle on a level place. Keep the engine running. 2. With the parking brake applied, place the shift lever in PARK (P). 3. With your foot on the brake pedal, move the shift lever through each gear, pausing for about three seconds in each one.
Page 297: Engine Coolant
How to Add Automatic Transmission Fluid Refer to the Maintenance Schedule to determine what kind of transmission ﬂuid to use. See Recommended Fluids and Lubricants on page 6-12. If the ﬂuid level is low, add only enough of the proper ﬂuid to bring the level into the crosshatched area on the dipstick.
Page 298: What To Use
What to Use Use a mixture of one-half clean, drinkable water and ® one-half DEX-COOL engine coolant which will not damage aluminum parts. If this coolant mixture is used, nothing else needs to be added. CAUTION: Adding only plain water to your cooling system can be dangerous.
Page 299: Adding Coolant
The vehicle must be on a level surface when checking the coolant level. When the engine is cold, the coolant level should be at the COLD FILL line or a little higher. The COLD FILL line is near the bottom of the recovery tank and has an arrow pointing down at it.
Page 300: Pressure Cap
Pressure Cap Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur. Be sure the cap is properly and tightly secured. See Engine Compartment Overview on page 5-12 for more information on location. 5-30 Engine Overheating There is a coolant temperature gage and a warning light...
Page 301: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Turn it off and get everyone away from the vehicle until it cools down.
Page 302: Overheated Engine Protection
If you no longer have the overheat warning, you can drive. Just to be safe, drive slower for about 10 minutes. If the warning does not come back on, you can drive normally. If the warning continues and you have not stopped, pull over, stop, and park your vehicle right away.
Page 303: Cooling System
Cooling System When you decide it is safe to lift the hood, this is what you will see: 3.6L V6 Engine A. Coolant Recovery Tank B. Pressure Cap C. Electric Engine Cooling Fans 3.8L V6 Engine A. Coolant Recovery Tank B.
Page 304 5.3L V8 Engine A. Pressure Cap B. Electric Engine Cooling Fans C. Coolant Recovery Tank 5-34 CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you. Keep hands, clothing, and tools away from any underhood electric fan.
Page 305 CAUTION: Heater and radiator hoses, and other engine parts, can be very hot. Do not touch them. If you do, you can be burned. Do not run the engine if there is a leak. If you run the engine, it could lose all coolant. That could cause an engine ﬁre, and you could be burned.
Page 306 How to Add Coolant to the Coolant Recovery Tank CAUTION: Adding only plain water to the cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle’s coolant warning system is set for the proper coolant mixture.
Page 307 CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. When the coolant level in the coolant recovery tank is at the COLD FILL line, start the vehicle.
Page 308 How to Add Coolant to the Cooling System (3.6L V6 Engine) Notice: The engine has a speciﬁc cooling system drain and ﬁll procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged. If the engine’s cooling system needs to be drained and re-ﬁlled, please see the dealer/retailer.
Page 309: How To Add Coolant To The Radiator
5. Then ﬁll the coolant recovery tank to the COLD FILL line. 6. Reinstall the coolant recovery tank cap and the pressure cap. 7. If the coolant in the recovery tank is constantly low, you should have your dealer/retailer service department inspect the vehicle for leaks.
Page 310 2. Then keep turning the pressure cap, but now push down as you turn it. Remove the pressure cap. 3. Open the coolant air bleed valve located on the thermostat housing, near the upper radiator hose. 5-40 See Engine Compartment Overview on page 5-12 for more information on location.
Page 311 6. Then ﬁll the coolant recovery tank to the COLD FILL line. 7. Put the cap back on the coolant recovery tank, but leave the radiator pressure cap off. 8. Start the engine and let it run until you can feel the upper radiator hose getting hot.
Page 312 How to Add Coolant to the Cooling System (5.3L V8 Engine) Notice: The engine has a speciﬁc cooling system drain and ﬁll procedure. Failure to follow this procedure could cause the engine to overheat and be severely damaged. If the engine’s cooling system needs to be drained and re-ﬁlled, please see the dealer/retailer.
Page 313: Power Steering Fluid
5. Then ﬁll the coolant recovery tank to the COLD FILL line. 6. Install the coolant recovery tank cap and the pressure cap. After a day or two of driving, when the engine is cold, check the coolant level in the recovery tank.
Page 314: Windshield Washer Fluid
How to Check Power Steering Fluid To check the power steering ﬂuid, do the following: 1. Turn the key off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag.
Page 315: Adding Washer Fluid
Adding Washer Fluid When the windshield washer ﬂuid is low, a low washer ﬂuid light may appear on the instrument panel cluster. See Low Washer Fluid Warning Light on page 3-47 for more information. In addition, if your vehicle has a Driver Information Center (DIC), the LOW WASHER FLUID message will display when the ﬂuid level is low.
Page 316: Brakes
Brakes Brake Fluid The brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down. The ﬁrst is that the brake ﬂuid goes down to an acceptable level during normal brake lining wear.
Page 317: Brake Wear
CAUTION: With the wrong kind of ﬂuid in the brake hydraulic system, the brakes might not work well. This could cause a crash. Always use the proper brake ﬂuid. Notice: • Using the wrong ﬂuid can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they...
Page 318: Brake Adjustment
Brake Pedal Travel See your dealer/retailer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign that brake service might be required. Brake Adjustment Every time you apply the brakes, with or without the vehicle moving, the brakes adjust for wear.
Page 319: Battery
Battery Your vehicle has a maintenance free battery. When it is time for a new battery, see your dealer/retailer for one that has the replacement number shown on the original battery’s label. See Engine Compartment Overview on page 5-12 for battery location. Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause...
Page 320: Jump Starting
Jump Starting If your vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: •...
Page 321 Notice: If you leave your radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by your warranty. Always turn off your radio and other accessories when jump starting your vehicle. 3.
Page 322 Always use the remote positive (+) terminal instead of the positive (+) terminal on the battery. If your vehicle has the 5.3L V8 engine, to uncover the remote positive (+) terminal, remove the fuse block cover. 5.3L Engine CAUTION: An electric fan can start up even when the engine is not running and can injure you.
Page 323 CAUTION: (Continued) Battery ﬂuid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, ﬂush the place with water and get medical help immediately. 5. Check that the jumper cables do not have loose or missing insulation.
Page 324 5.3L Engine 6. Connect the red positive (+) cable to the positive (+) terminal location on the vehicle with the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal location on the vehicle with the good battery.
Page 325 Jumper Cable Removal A. Heavy, Unpainted Metal Engine Part or Remote Negative ( ) Terminal B. Good Battery or Remote Positive (+) and Remote Negative ( ) Terminals C. Dead Battery or Remote Positive (+) Terminal To disconnect the jumper cables from both vehicles, do the following: 1.
Page 326: Headlamp Aiming
Headlamp Aiming The vehicle has a visual optical headlamp aiming system. The aim has been preset at the factory and should need no further adjustment However, if the vehicle is damaged in a crash, the headlamp aim may be affected and adjustment may be necessary.
Page 327 To adjust the vertical aim on the headlamps: 1. Open the hood. See Hood Release on page 5-11 for more information. 2. Locate the aim dot on the lens of the low-beam headlamp. 3. Measure the distance from the ground to the aim dot on the low-beam headlamp.
Page 328: Bulb Replacement
7. Locate the vertical headlamp aiming screws, which are under the hood near each headlamp assembly. The adjustment screw can be turned with a 6 mm male hex. 8. Turn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line. Turn it clockwise or counterclockwise to raise or lower the angle of the beam.
Page 329: Taillamps, Turn Signal, Sidemarker, Stoplamps And Back-Up Lamps
Taillamps, Turn Signal, Sidemarker, Stoplamps and Back-up Lamps To replace a taillamp, turn signal, sidemarker, stoplamp or back-up lamp bulb: 1. Open the trunk. See Trunk on page 2-14 for more information. 2. Remove the convenience net if the vehicle has one. 3.
Page 330 5. Remove the two wing nuts holding the taillamp assembly in place. 6. Pull out the taillamp assembly and disconnect the wiring harness. 5-60 A. Taillamp D. Stoplamp/Taillamp/Turn B. Back-up Signal C. Taillamp E. Sidemarker 7. Turn the bulb socket counterclockwise to remove it. 8.
Page 331: License Plate Lamp
License Plate Lamp To replace one of these bulbs: 1. Remove the screws for either of the license plate lamps. 2. Turn and pull the license plate lamp forward through the fascia opening. 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket.
Page 332: Windshield Replacement
Windshield Replacement Your vehicle is equipped with an acoustic windshield. If you ever have to have your windshield replaced be sure to get an acoustic windshield so you will continue to have the beneﬁts an acoustic windshield can provide. Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear or cracking.
Page 333: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. CAUTION: Poorly maintained and improperly used tires are dangerous.
Page 334: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P-Metric) Tire Example (A) Tire Size The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 335 (G) Maximum Cold Inﬂation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load. Compact Spare Tire Example (A) Temporary Use Only The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h).
Page 336 (D) Maximum Cold Inﬂation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load. (E) Tire Inﬂation The temporary use tire or compact spare tire should be inﬂated to 60 psi (420 kPa). For more information on tire pressure and inﬂation see Inﬂation - Tire Pressure on page 5-70.
Page 337: Tire Terminology And Deﬁnitions
(C) Aspect Ratio A two-digit number that indicates the tire height-to-width measurements. For example, if the tire size aspect ratio is 60, as shown in item C of the illustration, it would mean that the tire’s sidewall is 60 percent as high as it is wide.
Page 338 Curb Weight The weight of a motor vehicle with standard and optional equipment including the maximum capacity of fuel, oil, and coolant, but without passengers and cargo. DOT Markings A code molded into the sidewall of a tire signifying that the tire is in compliance with the U.S.
Page 339 Passenger (P-Metric) Tire A tire used on passenger cars and some light duty trucks and multipurpose vehicles. Recommended Inﬂation Pressure manufacturer’s recommended tire inﬂation pressure as shown on the tire placard. See Inﬂation - Tire Pressure on page 5-70 and Loading Your Vehicle on page 4-21.
Page 340: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following: •...
Page 341: How To Check
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are under-inﬂated. Check the tire’s inﬂation pressure when the tires are cold.
Page 342 Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inﬂation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.
Page 343: Tire Pressure Monitor Operation
Tire Pressure Monitor Operation The Tire Pressure Monitor System (TPMS) is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the vehicle’s tires and transmits the tire pressure readings to a receiver located in the vehicle.
Page 344: Tpms Malfunction Light And Message
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light ﬂashes for about one minute and then stays on for the remainder of the ignition cycle.
Page 345: Tire Inspection And Rotation
To decrease the tire’s air-pressure use the pointed end of the valve cap, a pencil-style air pressure gage,or a key. You have two minutes to match each tire and wheel position. If it takes longer than two minutes to match any tire and wheel position, the matching process stops and you need to start over.
Page 346 The purpose of a regular tire rotation is to achieve a uniform wear for all tires on the vehicle. This will ensure that your vehicle continues to perform most like it did when the tires were new. Any time you notice unusual wear, rotate the tires as soon as possible and check wheel alignment.
Page 347: When It Is Time For New Tires
When It Is Time for New Tires Various factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions inﬂuence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch...
Page 348: Buying New Tires
Buying New Tires GM has developed and matched speciﬁc tires for your vehicle. The original equipment tires installed on your vehicle, when it was new, were designed to meet General Motors Tire Performance Criteria Speciﬁcation (TPC Spec) system rating. If you need replacement tires, GM strongly recommends that you get tires with the same TPC Spec rating.
Page 349 CAUTION: If you use bias-ply tires on your vehicle, the wheel rim ﬂanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly, causing a crash. Use only radial-ply tires with the wheels on your vehicle. If you must replace your vehicle’s tires with those that do not have a TPC Spec number, make sure they are the same size, load range, speed rating,...
Page 350: Different Size Tires And Wheels
Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover.
Page 351 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Page 352: Wheel Alignment And Tire Balance
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment might need to be checked.
Page 353 CAUTION: Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured.
Page 354: Tire Chains
Used Replacement Wheels CAUTION: Putting a used wheel on your vehicle is dangerous. You cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
Page 355 CAUTION: (Continued) Use another type of traction device only if its manufacturer recommends it for use on your vehicle and tire size combination and road conditions. Follow that manufacturer’s instructions.To help avoid damage to your vehicle, drive slowly, readjust or remove the device if it is contacting your vehicle, and do not spin your wheels.
Page 356: If A Tire Goes Flat
If a Tire Goes Flat It is unusual for a tire to blowout while you are driving, especially if you maintain your vehicle’s tires properly. If air goes out of a tire, it is much more likely to leak out slowly.
Page 357: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your vehicle’s hazard warning ﬂashers. See Hazard Warning Flashers on page 3-6 for more information. CAUTION: Changing a tire can be dangerous.
Page 358: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The equipment you will need is located in the trunk. 1. Open the trunk. See Trunk on page 2-14 for more information. 2. Remove the convenience net if the vehicle has one. 3. Remove the spare tire cover. 4.
Page 359: Removing The Flat Tire And Installing The Spare Tire
The tools you will need to change a tire include the jack (A), extension and protection guide (B), and wheel wrench (C). Removing the Flat Tire and Installing the Spare Tire You vehicle may have wheels with exposed wheel nuts. If so, go to the Removing the Wheel Nuts section.
Page 360 Removing the Wheel Nuts 1. Place the wheel wrench securely over the wheel nut. Turn the wheel wrench counterclockwise to loosen all the wheel nuts, but do no remove them yet. 2. Turn the jack handle clockwise to raise the jack lift head.
Page 361 6. Remove all wheel nuts and take off the ﬂat tire. 5. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground for the compact spare tire to ﬁt under the vehicle. 5-91...
Page 362 CAUTION: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
Page 363 CAUTION: Never use oil or grease on studs or nuts. Because the nuts might come loose. The vehicle’s wheel could fall off, causing a crash. 9. Put the wheel nuts back on with the rounded end of the nuts toward the wheel. Tighten each nut by hand until the wheel is held against the hub.
Page 364 CAUTION: Incorrect or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to a crash. If you have to replace them, be sure to get new original equipment wheel nuts. Stop somewhere as soon as you can and have the nuts tightened with a torque wrench to the proper torque speciﬁcation.
Page 365: Storing A Flat Or Spare Tire And Tools (Base Model)
Storing a Flat or Spare Tire and Tools (Base Model) CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
Page 366 A. Cover B. Retainer C. Compact Spare Tire D. Wing Nut E. Jack F. Wheel Wrench G. Extension Protector H. Foam Holder I. Bolt Screw Compact Spare Tire 5-96 A. Retainer B. Full-Size Flat Tire C. Protective Guide D. Extension Bolt Screw E.
Page 367 Storing a Flat or Spare Tire and Tools (Super Only) Super Model CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
Page 368: Compact Spare Tire
A. Retainer B. Full-Size Flat Tire C. Protective Guide D. Extension Bolt Screw E. Wing Nut F. Jack G. Wheel Wrench H. Foam Holder I. Bolt Screw Full-Size Flat Tire 5-98 Compact Spare Tire Although the compact spare tire was fully inﬂated when the vehicle was new, it can lose air after a time.
Page 369: Appearance Care
Appearance Care Interior Cleaning Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces. Regular vacuuming is recommended to remove particles from your upholstery.
Page 370: Fabric/Carpet
Do not clean your vehicle using the following cleaners or techniques: • Never use a knife or any other sharp object to remove a soil from any interior surface. • Never use a stiff brush. It can cause damage to your vehicle’s interior surfaces.
Page 371: Leather
If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness ﬁrst. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface.
Page 372: Care Of Safety Belts
Care of Safety Belts Keep belts clean and dry. CAUTION: Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Page 373: Cleaning Exterior Lamps/Lenses
Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water, a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under Washing Your Vehicle on page 5-102. Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint ﬁnish.
Page 374: Windshield And Wiper Blades
Protecting Exterior Bright Metal Parts Bright metal parts should be cleaned regularly to keep their luster. Washing with water is all that is usually needed. However, you may use chrome polish on chrome or stainless steel trim, if necessary. Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean aluminum.
Page 375: Tires
Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by your warranty. Use chrome polish on chrome wheels only. Use chrome polish only on chrome-plated wheels, but avoid any painted surface of the wheel, and buff off immediately after application.
Page 376: Underbody Maintenance
Underbody Maintenance Chemicals used for ice and snow removal and dust control can collect on the underbody. If these are not removed, corrosion and rust can develop on the underbody parts such as fuel lines, frame, ﬂoor pan, and exhaust system even though they have corrosion protection.
Page 377: Vehicle Identiﬁcation
Description Cleans, shines, and Foaming Tire Shine Low protects tires. No wiping Gloss necessary. Medium foaming shampoo. Cleans and Wash Wax Concentrate lightly waxes. Biodegradable and phosphate free. Quickly removes spots Spot Lifter and stains from carpets, vinyl, and cloth upholstery. Odorless spray odor Odor Eliminator eliminator used on fabrics,...
Page 378: Service Parts Identiﬁcation Label
Service Parts Identiﬁcation Label This label is in the trunk. It is very helpful if you ever need to order parts. The label has the following information: • Vehicle Identiﬁcation Number (VIN) • Model designation • Paint information • Production options and special equipment Do not remove this label from the vehicle.
Page 379: Headlamp Wiring
Headlamp Wiring The headlamp wiring is protected by a circuit breaker. An electrical overload will cause the lamps to go on and off, or in some cases to remain off. If this happens, have your headlamp wiring checked right away. Windshield Wiper Fuses The windshield wiper motor is protected by a circuit breaker and a fuse.
Page 380: Instrument Panel Fuse Block
Instrument Panel Fuse Block The instrument panel fuse block is located on the passenger side of the instrument panel. Pull off the cover labeled FUSES to expose the fuse block. 5-110...
Page 381 Fuses Usage DR/LCK Door Locks, Trunk TRUNK RFA/MOD Remote Keyless Entry PRK/SWTCH Ignition Key Lock CLSTR Cluster STR/WHL/ Steering Wheel Controls Illumination ILLUM ® ONSTAR/ALDL OnStar , Data Link INT/ILLUM Interior Lamps PWR/SEAT Power Seat S/ROOF Sunroof CNSTR Canister Vent HVAC Climate Control System HAZRD...
Page 382: Underhood Fuse Block
Underhood Fuse Block Some fuses and relays are located in the underhood fuse block on the passenger side of the vehicle in the engine compartment. See Engine Compartment Overview on page 5-12 for more information on location. Notice: Spilling liquid on any electrical components on your vehicle may damage it.
Page 383 Mini-Fuses Usage Fuel Pump Antilock Brake System Ignition J-Style Fuses Usage Air Pump Battery Main 1 Battery Main 2 Battery Main 3 Fan 1 Battery Main 4 Antilock Brake System Motor Fan 2 Starter Micro-Relays Usage Headlamp High-Beam Headlamp Driver Module Fog Lamp Ignition 1 Micro-Relays...
Page 384 5.3L V8 Engine Fuses HVAC Climate Control System FUEL/PUMP Fuel Pump AIRBAG/ Airbag, Display DISPLAY COMPASS Compass Antilock Brake System 5-114 ETC/ECM A/C CMPRSR ECM/TCM TRANS EMISSIONS1 ABS SOL ECM IGN EMISSIONS2 AUX PWR Usage WSW/RVC LT LO BEAM RT LO BEAM FOG LAMPS LT HI BEAM Fuses...
Page 385 Fuses Usage HORN Horn Passenger Side High-Beam RT HI BEAM Headlamp BATT 4 Battery 4 BATT 1 Battery 1 STRTR Starter ABS MTR Antilock Brake System Motor BATT 3 Battery 3 BATT 2 Battery 2 FAN 2 Cooling Fan 2 FAN 1 Cooling Fan 1 Relays...
Page 386: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. Application Air Conditioning Refrigerant R134a Automatic Transmission (Drain and Reﬁll) Cooling System Including Reservoir 3.6L V6 and 3.8L V6 Engine 5.3L V8 Engine Engine Oil with Filter 3.6L V6 Engine 3.8L V6 Engine 5.3L V8 Engine...
Page 387 Capacities and Speciﬁcations (cont’d) Application 3.6LV6 Engine sold new in all states 5.3L V8 Engine Wheel Nut Torque All capacities are approximate. When adding, be sure to ﬁll to the approximate level, as recommended in this manual. See Scheduled Maintenance on page 6-4 Engine 3.6L V6 Engine 3.8L V6 Engine...
Page 388 NOTES 5-118...
Page 389: Maintenance Schedule
Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-2 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-8 At Each Fuel Fill ...6-8 At Least Once a Month ...6-9 At Least Once a Year ...6-9 Recommended Fluids and Lubricants ...6-12...
Page 390: Maintenance Requirements
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer/retailer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and...
Page 391 This schedule is for vehicles that: • carry passengers and cargo within recommended limits. You will ﬁnd these limits on the Tire and Loading Information label. See Loading Your Vehicle on page 4-21. • are driven on reasonable road surfaces within legal driving limits.
Page 392: Scheduled Maintenance
Scheduled Maintenance When the change engine oil light or CHANGE OIL SOON DIC message comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Page 393 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. See Engine Oil on page 5-18. Reset oil life system. See Engine Oil Life System on page 5-21. An Emission Control Service. Visually check for any leaks or damage. See footnote (k). Inspect engine air cleaner ﬁlter.
Page 394: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 395: Maintenance Footnotes
Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chaﬁng, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts, including calipers, parking brake, etc. (b) Visually inspect front and rear suspension and steering system for damaged, loose, or missing parts or signs of wear.
Page 396: Engine Oil Level Check
(i) Drain, ﬂush, and reﬁll cooling system. This service can be complex; you should have your dealer/retailer perform this service. See Engine Coolant on page 5-27 for what to use. Inspect hoses. Clean radiator, condenser, pressure cap, and ﬁller neck. Pressure test the cooling system and pressure cap.
Page 397: At Least Once A Month
Engine Coolant Level Check Check the engine coolant level and add DEX-COOL coolant mixture if necessary. See Engine Coolant on page 5-27. Windshield Washer Fluid Level Check Check the windshield washer ﬂuid level in the windshield washer ﬂuid reservoir and add the proper ﬂuid if necessary.
Page 398: Ignition Transmission Lock Check
Automatic Transmission Shift Lock Control System Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.
Page 399: Underbody Flushing Service
Parking Brake and Automatic Transmission Park (P) Mechanism Check CAUTION: When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll.
Page 400: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certiﬁed for Gasoline Engines Engine Oil starburst symbol.
Page 401: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Part Engine Air Cleaner/Filter 3.6L and 3.8L Engines 5.3L Engine Engine Oil Filter 3.6L V6 and 5.3L V8 Engines 3.8L V6 Engine Passenger Compartment Air Filter Spark Plugs 3.6L V6 Engine...
Page 402: Engine Drive Belt Routing
Engine Drive Belt Routing 3.8L V6 Engine 3.6L V6 Engine 6-14...
Page 403 5.3L V8 Engine 6-15...
Page 404: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. You should retain all maintenance receipts.
Page 405 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 406 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 407: Customer Assistance Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-5 Customer Assistance for Text Telephone (TTY) Users ...7-6 Customer Assistance Offices ...7-6 GM Mobility Reimbursement Program ...7-7 Roadside Assistance Program ...7-8 Scheduling Service Appointments ...7-10 Courtesy Transportation ...7-10 Collision Damage Repair ...7-12 Customer Assistance Information...
Page 408: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Buick. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your GM dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 409 STEP THREE — U.S. Owners: Both General Motors and your dealer are committed to making sure you are completely satisﬁed with your new vehicle. However, in the United States, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, you should ﬁle with the BBB Auto Line Program to enforce your rights.
Page 410 STEP THREE — Canadian Owners: In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps one and two, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/Arbitration program.
Page 411: Online Owner Center
Online Owner Center (United States only) The Owner Center is a resource for your GM ownership needs. Speciﬁc vehicle information can be found in one place. The Online Owner Center allows you to: • Get e-mail service reminders. • Access information about your speciﬁc vehicle, including tips and videos and an electronic version of this owner manual.
Page 412: Customer Assistance For Text Telephone (Tty) Users
Customer Assistance Offices Buick encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Buick, the letter should be addressed to: United States — Customer Assistance Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-5136 www.Buick.com...
Page 413: Gm Mobility Reimbursement Program
Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P. 11910, Mexico, D.F. 01-800-508-0000 Long Distance: 011-52-53 29 0 800 GM Mobility Reimbursement...
Page 414: Roadside Assistance Program
(Text Telephone (TTY): 1-888-889-2438). For vehicles purchased in Canada, call 1-800-268-6800. Service is available 24 hours a day, 365 days a year. As the owner of a new Buick vehicle, you are automatically enrolled in the Buick Roadside Assistance program.
Page 415: Calling For Assistance
However, any cost for parts and labor for non-warranty repairs are the responsibility of the driver. Buick and General Motors of Canada Limited reserve the right to limit services or reimbursement to an owner or driver when, in their sole discretion, the claims become excessive in frequency or type of occurrence.
Page 416: Scheduling Service Appointments
Roadside Assistance is not part of or included in the coverage provided by the New Vehicle Limited Warranty. Buick and General Motors of Canada Limited reserve the right to make any changes or discontinue the Roadside Assistance program at any time without notiﬁcation.
Page 417: Transportation Options
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following: Shuttle Service Shuttle service is the preferred means of offering Courtesy Transportation.
Page 418: Collision Damage Repair
Additional Program Information All program options, such as shuttle service, may not be available at every dealer. Please contact your dealer for speciﬁc information about availability. All Courtesy Transportation arrangements will be administered by appropriate dealer personnel. General Motors reserves the right to unilaterally modify, change or discontinue Courtesy Transportation at any time and to resolve all questions of claim eligibility pursuant to the terms and conditions described...
Page 419: Repair Facility
Repair Facility GM also recommends that you choose a collision repair facility that meets your needs before you ever need collision repairs. Your dealer/retailer may have a collision repair center with GM-trained technicians and state of the art equipment, or be able to recommend a collision repair center that has GM-trained technicians and comparable equipment.
Page 420 • Remove any valuables from your vehicle before it is towed away. Make sure this includes your insurance information and registration if you keep these items in your vehicle. • Gather the important information you will need from the other driver. Things like name, address, phone number, driver’s license number, vehicle license plate, vehicle make, model and model year, Vehicle Identiﬁcation Number (VIN), insurance company...
Page 421: Reporting Safety Defects
If another party’s insurance company is paying for the repairs, you are not obligated to accept a repair valuation based on that insurance company’s collision policy repair limits, as you have no contractual limits with that company. In such cases, you can have control of the repair and parts choices as long as cost stays within reasonable limits.
Page 422: Reporting Safety Defects To General Motors
General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, please notify General Motors. Call 1-800-521-7300, or write: Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-5136 In Canada, call 1-800-263-3777 (English) or 1-800-263-7854 (French), or write:...
Page 423: Vehicle Data Recording And Privacy
ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc. on the World Wide Web at: www.helminc.com Or you can write to: Helm, Incorporated P.O. Box 07130 Detroit, MI 48207 Prices are subject to change without notice and without incurring obligation.
Page 424: Event Data Recorders
Event Data Recorders This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed.
Page 425: Onstar
® OnStar If your vehicle has OnStar and you subscribe to the OnStar services, please refer to the OnStar Terms and Conditions for information on data collection and use. ® See also OnStar System on page 2-43 in this manual for more information.
Page 426 NOTES 7-20...
Page 427 Accessories and Modiﬁcations ... 5-3 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-67 Additives, Fuel ... 5-7 Add-On Electrical Equipment ... 5-108 Air Cleaner/Filter, Engine ... 5-23 Air Conditioning ... 3-20, 3-24 Airbag Passenger Status Indicator ... 3-34 Readiness Light ... 3-33 Airbag System ...
Page 428 Audio System(s) ... 3-86 Automatic Door Lock ... 2-12 Automatic Transmission Fluid ... 5-25 Operation ... 2-29 Backglass Antenna ... 3-104 Battery ... 5-49 Electric Power Management ... 3-18 Exterior Lighting Battery Saver ... 3-15 Run-Down Protection ... 3-19 Brake Emergencies ...
Page 429 Child Restraints (cont.) Securing a Child Restraint in the Center Front Seat Position ... 1-50 Securing a Child Restraint in the Right Front Seat Position ... 1-50 Where to Put the Restraint ... 1-39 Chime Level Adjustment ... 3-105 Cigarette Lighter ... 3-20 Cleaning Aluminum or Chrome-Plated Wheels ...
Page 430 Daytime Running Lamps/Automatic Headlamp System ... 3-14 Defensive Driving ... 4-2 Delayed Entry Lighting ... 3-17 Delayed Exit Lighting ... 3-17 Delayed Locking ... 2-12 DIC Compass ... 3-56 Diesel Running Out of Fuel ... 2-37 Disc, MP3 ... 3-97 Doing Your Own Service Work ...
Page 431 Engine Air Cleaner/Filter ... 5-23 Change Engine Oil Light ... 3-45 Check and Service Engine Soon Light ... 3-42 Coolant ... 5-27 Coolant Heater ... 2-27 Coolant Temperature Gage ... 3-40 Coolant Temperature Warning Light ... 3-40 Drive Belt Routing ... 6-14 Engine Compartment Overview ...
Page 432 Fuses Fuses and Circuit Breakers ... 5-109 Instrument Panel Fuse Block ... 5-110 Underhood Fuse Block ... 5-112 Windshield Wiper ... 5-109 Gage Engine Coolant Temperature ... 3-40 Fuel ... 3-48 Speedometer ... 3-32 Tachometer ... 3-32 Garage Door Opener ... 2-47 Gasoline Octane ...
Page 433 Instrument Panel (I/P) Brightness ... 3-16 Cluster ... 3-31 Interior Lamps ... 3-16 Jump Starting ... 5-50 Keyless Entry System ... 2-4 Keys ... 2-3 Labeling, Tire Sidewall ... 5-64 Lamps Courtesy ... 3-16 Exterior Lighting Battery Saver ... 3-15 Overhead Console Reading ...
Page 434 Lighting Delayed Entry ... 3-17 Delayed Exit ... 3-17 Entry ... 3-16 Perimeter ... 3-17 Theater Dimming ... 3-17 Lights Exterior Lamps ... 3-13 Flash-to-Pass ... 3-8 High/Low Beam Changer ... 3-8 Interior Lamps ... 3-16 Loading Your Vehicle ... 4-21 Lockout Protection ...
Page 435 MP3 ... 3-97 MyGMLink.com ... 7-5 Navigation System, Privacy ... 7-19 New Vehicle Break-In ... 2-24 Odometer ... 3-32 Off-Road Recovery ... 4-11 Change Engine Oil Light ... 3-45 Engine ... 5-18 Pressure Light ... 3-45 Oil, Engine Oil Life System ... 5-21 Older Children, Restraints ...
Page 436 Perimeter Lighting ... 3-17 Power Door Locks ... 2-11 Electrical System ... 5-109 Lumbar Controls ... 1-3 Reduced Engine Light ... 3-46 Retained Accessory (RAP) ... 2-25 Seat ... 1-2 Steering Fluid ... 5-43 Windows ... 2-18 Pressure Cap ... 5-30 Privacy ...
Page 437 Roadside Assistance Program ... 7-8 Rocking Your Vehicle to Get it Out ... 4-21 Routing, Engine Drive Belt ... 6-14 Running Out of Fuel ... 2-37 Safety Belt Reminder Light ... 3-32 Safety Belts Care of ... 5-102 How to Wear Safety Belts Properly ... 1-14 Lap Belt ...
Page 438 ® StabiliTrak System ... 4-8 Start Vehicle, Remote ... 2-8 Starting the Engine ... 2-26 Steering ... 4-9 Steering Wheel Controls, Audio ... 3-102 Steering Wheel, Tilt Wheel ... 3-6 Storage Areas Center Console Storage Area ... 2-53 Convenience Net ... 2-54 Cupholder(s) ...
Page 439 Towing Recreational Vehicle ... 4-27 Towing a Trailer ... 4-28 Your Vehicle ... 4-27 Traction Control System (TCS) ... 4-6 Control System Warning Light ... 3-38 Enhanced Traction System (ETS) ... 4-7 Enhanced Traction System (ETS) Warning Light ... 3-39 ®...
Page 440 Warning Lights, Gages and Indicators ... 3-30 Warnings DIC Warnings and Messages ... 3-58 Hazard Warning Flashers ... 3-6 Other Warning Devices ... 3-6 Safety and Symbols ... iii Vehicle Damage ... iv Washer Fluid, Low Warning Light ... 3-47 Wheels Alignment and Tire Balance ...

This manual is also suitable for:

Lacrosse 2008

Buick Automobile User Manual

Section 1 Seats and Restraint Systems

Front Seats

Rear Seats

Safety Belts

Child Restraints

Airbag System

Restraint System Check

Section 2 Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Object Detection Systems

Onstar System

Universal Home Remote System

Storage Areas

Sunroof

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Windshield Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Buick Automobile

Summary of Contents for Buick Automobile