Page 1 2006 Buick LaCrosse Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-2 Rear Seats ... 1-7 Safety Belts ... 1-8 Child Restraints ... 1-28 Airbag System ... 1-53 Restraint System Check ... 1-67 Features and Controls ... 2-1 Keys ...
Page 2: How To Use This Manual
GENERAL MOTORS, GM, the GM Emblem, BUICK, and the BUICK Emblem are registered trademarks, and ® the name LACROSSE is a trademark of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without notice.
Page 3 Safety Warnings and Symbols There are a number of safety cautions in this book. We use a box and the word CAUTION to tell about things that could hurt you if you were to ignore the warning. CAUTION: These mean there is something that could hurt you or other people.
Page 4 Vehicle Damage Warnings Also, in this manual you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice tells about something that can damage the vehicle. Many times, this damage would not be covered by your vehicle’s warranty, and it could be costly.
Page 5 These are some examples of symbols that may be found on the vehicle:...
Page 6 NOTES...
Page 7: Table Of Contents
Section 1 Front Seats ...1-2 Manual Seats ...1-2 Six-Way Power Seats ...1-3 Power Lumbar ...1-3 Heated Seats ...1-4 Reclining Seatbacks ...1-4 Head Restraints ...1-6 Center Seat ...1-7 Rear Seats ...1-7 Split Folding Rear Seat ...1-7 Safety Belts ...1-8 Safety Belts: They Are for Everyone ...1-8 Questions and Answers About Safety Belts ...1-13 How to Wear Safety Belts Properly ...1-14 Driver Position ...1-14...
Page 8: Front Seats
Front Seats Manual Seats CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 9: Six-Way Power Seats
Six-Way Power Seats If your vehicle has power seats, the controls are located on the outboard side of the seat cushions. • To move the entire seat forward or rearward, move the control forward or rearward. • To raise or lower the entire seat, move the control up or down.
Page 10 Heated Seats If your vehicle has this feature, the buttons are located on the climate control panel. Press the button once to activate the high heat setting. Both indicator lights on the button will come on. Press the button again to select the lower temperature setting.
Page 11 Do not have a seatback reclined if your vehicle is moving. CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job because it will not be against your body.
Page 12: Head Restraints
Head Restraints Pull up the head restraint to raise it. Press the release button, located at the base of the head restraint, and push the head restraint down to lower it. Adjust the head restraint so that the top of the restraint is closest to the top of the occupant’s head.
Page 13: Rear Seats
Center Seat Your vehicle may have a front center seat. There are cupholders on the underside of the seat cushion. To use them, ﬂip the seat cushion forward. This seat can also be converted to a storage area by lowering the armrest. See Center Console Storage Area on page 2-46.
Page 14: Safety Belts
CAUTION: If the seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatback to be sure it is locked. To raise the rear seatback, lift the seatback up until it latches.
Page 15 CAUTION: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 16: Why Safety Belts Work
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it is just a seat on wheels. 1-10...
Page 17 Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... 1-11...
Page 18 or the instrument panel... 1-12 or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense.
Page 19 Questions and Answers About Safety Belts Will I be trapped in the vehicle after an accident if I am wearing a safety belt? You could be — whether you are wearing a safety belt or not. But you can unbuckle a safety belt, even if you are upside down.
Page 20: How To Wear Safety Belts Properly
How to Wear Safety Belts Properly This part is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and babies. If a child will be riding in your vehicle, see Older Children on page 1-28 or Infants and Young Children on page 1-31.
Page 21 5. Move the shoulder belt height adjuster to the height that is right for you. See Shoulder Belt Height Adjustment on page 1-20. 6. To make the lap part tight, pull up on the shoulder belt. The lap part of the belt should be worn low and snug on the hips, just touching the thighs.
Page 22 What is wrong with this? The shoulder belt is too loose. It will not give nearly as much protection this way. 1-16 CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 23 What is wrong with this? The belt is buckled in the wrong place. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 24 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-18 CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 25 What is wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 26: Shoulder Belt Height Adjustment
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 27: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
Page 28: Center Front Passenger Position
Center Front Passenger Position Lap Belt If your vehicle has a front bench seat, someone can sit in the center position. When you sit in the center front seating position, you have a lap safety belt, which has no retractor. To make the belt longer, tilt the latch plate and pull it along the belt.
Page 29: Rear Seat Passengers
Rear Seat Passengers It is very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who are not safety belted can be thrown out of the vehicle in a crash.
Page 30 2. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. When the shoulder belt is pulled out all the way, it will lock. If it does, let it go back all the way and start again.
Page 31: Rear Safety Belt Comfort Guides
CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body. To unlatch the belt, push the button on the buckle. Rear Safety Belt Comfort Guides Rear shoulder belt comfort guides may provide added safety belt comfort for older children who have outgrown...
Page 32 2. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt, and insert the two edges of the belt into the slots of the guide. 1-26 3. Be sure that the belt is not twisted and it lies ﬂat. The elastic cord must be under the belt and the guide on top.
Page 33: Safety Belt Pretensioners
CAUTION: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Page 34: Child Restraints
Safety Belt Extender If the vehicle’s safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer will order you an extender. It is free. When you go in to order it, take the heaviest coat you will wear, so the extender will be long enough for you.
Page 35 What is the proper way to wear safety belts? An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should ﬁt snugly below the hips, just touching the top of the thighs.
Page 36 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? If the child is sitting in a seat next to a window, move the child toward the center of the vehicle.
Page 37: Infants And Young Children
Wherever the child sits, the lap portion of the belt should be worn low and snug on the hips, just touching the child’s thighs. This applies belt force to the child’s pelvic bones in a crash. Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children.
Page 38 CAUTION: Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its airbag system is designed for them.
Page 39 CAUTION: Newborn infants need complete support, including support for the head and neck. This is necessary because a newborn infant’s neck is weak and its head weighs so much compared with the rest of its body. In a crash, an infant in a rear-facing seat settles into the restraint, so the crash forces can be distributed across the strongest part of an infant’s body, the back and shoulders.
Page 40: Child Restraint Systems
Child Restraint Systems An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous ﬂat surface. Make sure that the infant’s head rests toward the center of the vehicle.
Page 41 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness.
Page 42 How Should I Use a Child Restraint? A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner.
Page 43 When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer.
Page 44: Where To Put The Restraint
Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We, therefore, recommend that child restraints be secured in a rear seat, including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat.
Page 45: Lower Anchors And Tethers For Children (Latch)
CAUTION: A child in a child restraint in the center front seat can be badly injured or killed by the right front passenger’s airbag if it inﬂates. Never secure a child restraint in the center front seat. It is always better to secure a child restraint in the rear seat.
Page 46 In order to use the LATCH system in your vehicle, you need a child restraint equipped with LATCH attachments. The child restraint manufacturer will provide you with instructions on how to use the child restraint and its attachments. The following explains how to attach a child restraint with these attachments in your vehicle.
Page 47 Top Tether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
Page 48 Lower Anchor and Top Tether Anchor Locations Seating positions with top tether anchors. (Lower Anchor): Seating positions with two lower anchors. Rear Seat 1-42 (Top Tether Anchor): To assist you in locating the lower anchors, each seating position with lower anchors has two labels, near the crease between the seatback and the...
Page 49 The top tether anchors are located under the trim covers on the rear seatback ﬁller panel. Flip open the trim cover to access the anchors. Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
Page 50 Securing a Child Restraint Designed for the LATCH System CAUTION: If a LATCH-type child restraint is not attached to anchors, the restraint will not be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Make sure that a LATCH-type child restraint is properly installed using the anchors, or use the vehicle’s safety belts to secure the restraint,...
Page 51 2. If the child restraint manufacturer recommends that the top tether be attached, attach and tighten the top tether to the top tether anchor, if equipped. Refer to the child restraint instructions and the following steps: 2.1. Find the top tether anchor. 2.2.
Page 52: Securing A Child Restraint In A Rear Seat Position
Securing a Child Restraint in a Rear Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-39. If your child restraint does not have the LATCH system, you will be using the lap-shoulder belt to secure the child restraint in this position.
Page 53 4. Pull the rest of the shoulder belt all the way out of 5. To tighten the belt, push down on the child restraint, the retractor to set the lock. pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor.
Page 54: Securing A Child Restraint In The Center Front Seat Position
6. If your child restraint manufacturer recommends using a top tether, attach and tighten the top tether to the top tether anchor. Refer to the instructions that came with the child restraint and see Lower Anchors and Tethers for Children (LATCH) on page 1-39.
Page 55: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Right Front Seat Position Your vehicle has a right front passenger’s airbag. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 1-38. In addition, your vehicle has a passenger sensing system.
Page 56 If you need to secure a forward-facing child restraint in the right front seat position, move the seat as far back as it will go before securing the forward-facing child restraint. See Manual Seats on page 1-2 or Six-Way Power Seats on page 1-3. If your child restraint is equipped with the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-39.
Page 57 4. Buckle the belt. Make sure the release button is 5. Pull the rest of the shoulder belt all the way out of positioned so you would be able to unbuckle the the retractor to set the lock. safety belt quickly if you ever had to. 1-51...
Page 58 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 59: Airbag System
Airbag System Your vehicle has a frontal airbag for the driver and a frontal airbag for the right front passenger. Your vehicle may also have roof-mounted side impact airbags. Roof-mounted side impact airbags are available for the driver and the passenger seated directly behind the driver and for the right front passenger and the passenger seated directly behind that passenger.
Page 60 CAUTION: Both frontal and side impact airbags inﬂate with great force, faster than the blink of an eye. If you are too close to an inﬂating airbag, as you would be if you were leaning forward, it could seriously injure you. Safety belts help keep you in position for airbag inﬂation before and during a crash.
Page 61: Where Are The Airbags
There is an airbag readiness light on the instrument panel cluster, which shows the airbag symbol. The system checks the airbag electrical system for malfunctions. The light tells you if there is an electrical problem. See Airbag Readiness Light on page 3-34 for more information.
Page 62 The right front passenger’s airbag is in the instrument panel on the passenger’s side. 1-56 If your vehicle has a side impact airbag for the driver and the person seated directly behind the driver, it is located in the ceiling above the side windows.
Page 63 If your vehicle has a side impact airbag for the right front passenger and the person directly behind that passenger, it is located in the ceiling above the side windows. CAUTION: If something is between an occupant and an airbag, the bag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 64: When Should An Airbag Inﬂate
When Should an Airbag Inﬂate? The driver’s and right front passenger’s frontal airbags are designed to inﬂate in moderate to severe frontal or near-frontal crashes. But they are designed to inﬂate only if the impact exceeds a predetermined deployment threshold. Deployment thresholds take into account a variety of desired deployment and non-deployment events and are used to predict how severe a crash is likely to be in time for the airbags to inﬂate and help...
Page 65: What Makes An Airbag Inﬂate
The threshold level can vary with speciﬁc vehicle design. Side impact airbags are not intended to inﬂate in frontal or near-frontal impacts, rollovers or rear impacts. A side impact airbag is intended to deploy on the side of the vehicle that is struck. In any particular crash, no one can say whether an airbag should have inﬂated simply because of the damage to a vehicle or because of what the repair costs...
Page 66: What Will You See After An Airbag Inﬂates
What Will You See After an Airbag Inﬂates? After a frontal airbag inﬂates, it quickly deﬂates, so quickly that some people may not even realize the airbag inﬂated. Roof-mounted side impact airbags deﬂate more slowly and may still be at least partially inﬂated minutes after the vehicle comes to rest.
Page 67: Passenger Sensing System
In many crashes severe enough to inﬂate an airbag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger airbag. • Airbags are designed to inﬂate only once. After an airbag inﬂates, you will need some new parts for your airbag system.
Page 68 The passenger sensing system works with sensors that are part of the right front passenger’s seat. The sensors are designed to detect the presence of a properly-seated occupant and determine if the passenger’s frontal airbag should be enabled (may inﬂate) or not. Accident statistics show that children are safer if they are restrained in the rear rather than the front seat.
Page 69 The passenger sensing system is designed to turn off the right front passenger’s frontal airbag if: • the right front passenger seat is unoccupied • the system determines that an infant is present in a rear-facing infant seat • the system determines that a small child is present in a forward-facing child restraint •...
Page 70 If a person of adult-size is sitting in the right front passenger’s seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. If this happens, turn the vehicle off and ask the person to place the seatback in the fully upright position, then sit upright in the seat, centered on the seat cushion, with the person’s legs comfortably extended.
Page 71: Servicing Your Airbag-Equipped Vehicle
You may want to consider not using seat covers or other aftermarket equipment if your vehicle has the passenger sensing system. See Adding Equipment to Your Airbag-Equipped Vehicle on page 1-66 for more information about modiﬁcations that can affect how the system operates. The passenger sensing system may suppress the airbag deployment when liquid is soaked into the seat.
Page 72: Adding Equipment To Your Airbag-Equipped Vehicle
Adding Equipment to Your Airbag-Equipped Vehicle Is there anything I might add to the front or sides of the vehicle that could keep the airbags from working properly? Yes. If you add things that change your vehicle’s frame, bumper system, front end or side sheet metal or height, they may keep the airbag system from working properly.
Page 73: Restraint System Check
Restraint System Check Checking the Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Page 74: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 75: Features And Controls
Section 2 Keys ...2-2 Remote Keyless Entry System ...2-3 Remote Keyless Entry System Operation ...2-4 Doors and Locks ...2-10 Door Locks ...2-10 Power Door Locks ...2-11 Delayed Locking ...2-11 Automatic Door Lock ...2-12 Rear Door Security Locks ...2-12 Lockout Protection ...2-13 Trunk ...2-13 Windows ...2-16 Power Windows ...2-17...
Page 76: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. They could operate the power windows or other controls or even make the vehicle move. The children or others could be badly injured or even killed.
Page 77: Remote Keyless Entry System
One key is used for the ignition and all locks. When a new vehicle is delivered, the key has a bar-coded key tag. This tag may be removed by your dealer before it is delivered. ® The vehicle has the PASS-Key III vehicle theft system.
Page 78: Remote Keyless Entry System Operation
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device. Changes or modiﬁcations to this system by other than an authorized service facility could void authorization to use this equipment.
Page 79 The following functions may be available with your vehicle’s remote keyless entry system: (Remote Vehicle Start): If your vehicle has this feature, the engine may be started from outside the vehicle using the remote keyless entry transmitter. See “Remote Vehicle Start” at the end of this section for more detailed information.
Page 80: Battery Replacement
Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about four years. You can tell the battery is weak if the transmitter will not work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it is probably time to change the battery.
Page 81: Remote Vehicle Start
Remote Vehicle Start Your vehicle may have a remote starting feature. This feature allows you to start the engine from outside of the vehicle. It may also start up the vehicle’s heating or air conditioning systems and rear window defogger. When the remote start system is active, the climate control system will heat and cool the inside of the vehicle based on the outside temperature.
Page 82 (Remote Start): If your vehicle has the remote start feature, the keyless entry transmitter will have a button with this symbol on it. To start the vehicle using the remote start feature, do the following: 1. Aim the transmitter at the vehicle. 2.
Page 83 The remote vehicle start feature will not operate if any of the follow occur: • The remote start system is disabled through the DIC. • The vehicle’s key is in the ignition. • A door on the vehicle is open. •...
Page 84: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 85: Power Door Locks
Power Door Locks To lock or unlock all doors from inside the vehicle, use the power door lock switch located on either front door armrest. Press the bottom of the switch to lock all doors. Press the top of the switch to unlock all doors. The driver’s and front passenger’s power door lock switch also releases the trunk lid.
Page 86: Automatic Door Lock
Automatic Door Lock The vehicle’s doors are programmed from the factory to lock when the shift lever is moved into a forward gear, and to unlock when the shift lever is moved into PARK (P). If someone needs to get in or out of the vehicle after the doors have been locked, place the shift lever into PARK (P).
Page 87: Lockout Protection
When you want to open a rear door when the security lock is on, do the following: 1. Unlock the door using the remote keyless entry transmitter, if equipped, the power door lock switch, or by lifting the rear door manual lock. 2.
Page 88: Remote Trunk Release
Opening the Trunk To open the trunk from the outside, use the remote keyless entry transmitter. See Remote Keyless Entry System Operation on page 2-4 for more information. The ignition must be off, or the transaxle must be in PARK (P), to open the trunk. If the vehicle has lost power, you can open the trunk by lowering the split folding rear seat, if equipped, and pulling the emergency trunk release handle located in...
Page 89 There is a glow-in-the-dark emergency trunk release handle located on the trunk latch of the trunk lid. This handle will glow following exposure to light. If ever needed, pull the emergency trunk release handle to open the trunk from the inside. Trunk Lid Pull Down Handle and Tie-Down Features Your vehicle has a trunk lid pull down handle (A)
Page 90: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 91: Power Windows
Power Windows The switches on the driver’s door armrest are used to control each of the windows. The power window switches work while the ignition is in RUN, ACCESSORY, or while Retained Accessory Power (RAP) is active. See Retained Accessory Power (RAP) on page 2-23. Each passenger door has its own window switch.
Page 92: Sun Visors
Sun Visors To block out glare, swing down the sun visors. They can be detached from the center retainer and slid along the rod to cover different areas of the front window and rotated to cover the side windows. Visor Vanity Mirror Swing down the sun visors and lift the cover to expose the vanity mirror.
Page 93: Arming With The Power Lock Switch
Arming with the Power Lock Switch The vehicle’s content theft-deterrent alarm system can be activated when the key is removed from the ignition and the power door lock switch of either the driver’s or front passenger’s door is used to lock the vehicle. The door needs to be in the open position when pressing the power door lock switch.
Page 94: Disarming With Your Key
Disarming with the Remote Keyless Entry Transmitter The alarm system will disarm when the remote keyless entry transmitter is used to unlock the doors. The red light will go out to show that the system is disarmed. Disarming with Your Key The alarm system will disarm when the key is used to unlock the doors.
Page 95: Theft-Deterrent Systems
® PASS-Key III Operation Your vehicle is equipped with PASS-Key (Personalized Automotive Security System) theft-deterrent system. PASS-Key theft-deterrent system. This means nothing special needs to be done to arm or disarm the system. It works when the key is inserted or removed from the ignition.
Page 96: Starting And Operating Your Vehicle
To program the new key do the following: 1. Verify that the new key has PK3 stamped on it. 2. Insert the master key in the ignition and start the engine. If the engine will not start, see your dealer for service. 3.
Page 97: Ignition Positions
Ignition Positions With the ignition key in the ignition, the key can be turned to four different positions: Notice: Using a tool to force the key from the ignition switch could cause damage or break the key. Use the correct key and turn the key only with your hand.
Page 98: Starting The Engine
Starting the Engine Move your shift lever to PARK (P) or NEUTRAL (N). The engine will not start in any other position — that is a safety feature. To restart when you are already moving, use NEUTRAL (N) only. Notice: Shifting into PARK (P) with the vehicle moving could damage the transaxle.
Page 99: Engine Coolant Heater
Engine Coolant Heater Your vehicle may be equipped with this feature. In very cold weather, 0°F ( 18°C) or colder, the engine coolant heater can help. You will get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Page 100: Automatic Transaxle Operation
Automatic Transaxle Operation Console Shift Lever Your vehicle’s automatic transaxle may have a shift lever on the steering column or on the console between the seats. 2-26 There is also a display located on the instrument panel cluster that will indicate the gear the vehicle is in.
Page 101 CAUTION: (Continued) Do not leave your vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle will not move, even when you are on fairly level ground, always set your parking brake and move the shift lever to PARK (P).
Page 102 NEUTRAL (N): In this position, the engine does not connect with the wheels. To restart when you are already moving, use NEUTRAL (N) only. Also, use NEUTRAL (N) when the vehicle is being towed. CAUTION: Shifting into a drive gear while your engine is running at high speed is dangerous.
Page 103 THIRD (3): This position is also used for normal driving, but it offers more power and lower fuel economy than AUTOMATIC OVERDRIVE (D). Here are some times you might choose THIRD (3) instead of AUTOMATIC OVERDRIVE (D): • When driving on hilly, winding roads. •...
Page 104: Parking Brake
Parking Brake To set the parking brake, hold the regular brake pedal down with your right foot. Push down the parking brake pedal with your left foot. To release the parking brake, hold the regular brake pedal down with your right foot and push the parking brake pedal with your left foot.
Page 105: Shifting Into Park (P)
Shifting Into Park (P) CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 106: Shifting Out Of Park (P)
Leaving Your Vehicle With the Engine Running CAUTION: It can be dangerous to leave your vehicle with the engine running. Your vehicle could move suddenly if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch ﬁre.
Page 107 The shift lock is always functional except in the case of a an uncharged or low voltage (less than 9 volt) battery. If your vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery.
Page 108: Parking Over Things That Burn
Parking Over Things That Burn CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. 2-34 Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you cannot see or smell.
Page 109: Running The Engine While Parked
Running the Engine While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 110: Mirrors
Mirrors Manual Rearview Mirror While sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side. The day/night control at the bottom of the mirror lets you adjust the mirror to avoid glare from the lamps behind you.
Page 111: Automatic Dimming Rearview Mirror With Onstar
Automatic Dimming Rearview Mirror ® with OnStar While sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side. The vehicle may have an automatic dimming rearview ®...
Page 112: Outside Power Heated Mirrors
Outside Power Heated Mirrors For information on the operation of the outside power mirrors see Outside Power Mirrors on page 2-37. If the vehicle has heated mirrors, they will warm up to melt ice and snow, and dissolve condensation when the defroster is turned on.
Page 113 ® A complete OnStar User’s Guide and the Terms and ® Conditions of the OnStar Subscription Service Agreement are included in the vehicle’s glove box literature. For more information, visit www.onstar.com or ® www.onstar.ca. Contact OnStar at 1-888-4-ONSTAR (1-888-466-7827), or press the OnStar ®...
Page 114 ® OnStar Virtual Advisor Your vehicle may have Virtual Advisor. It is a feature of ® OnStar Personal Calling that uses minutes to access weather, local traffic reports, and stock quotes. By pressing the phone button and giving a few simple voice commands, you can browse through the various topics.
Page 115: Universal Home Remote System
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Page 116: Programming Universal Home Remote
Be sure that people and objects are clear of the garage door or gate operator you are programming. When programming a garage door, it is advised to park outside of the garage. It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio-frequency signal.
Page 117: Gate Operator And Canadian Programming
6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7. Firmly press and release the “Learn” or “Smart” button.
Page 118: Storage Areas
Using Universal Home Remote Press and hold the appropriate Universal Home Remote button for at least half of a second. The indicator light will come on while the signal is being transmitted. Erasing Universal Home Remote Buttons To erase programming from the three Universal Home Remote buttons do the following: 1.
Page 119: Cupholder(S)
Cupholder(s) If your vehicle is the ﬁve-passenger model, there is a cupholder in front of the center console. The cupholder has an arm that adjusts to two positions to ﬁt either a large cup or two smaller cups. If your vehicle is the six-passenger model, there is a cupholder located underneath the seat.
Page 120: Center Console Storage Area
Center Console Storage Area If your vehicle has a ﬁve-passenger console, the center console has a padded lid that can be used as an armrest. Lift the armrest lid to access a storage bin with a coin holder and a CD holder. Located under the lid is a card clip.
Page 121: Sunroof
Sunroof The vehicle may have a sunroof. It includes a sliding glass panel and a sunshade. The sunroof control is on the headliner, by the map lamps. The sunroof control works only when the ignition is on or in ACCESSORY, or when Retained Accessory Power (RAP) is active.
Page 122 NOTES 2-48...
Page 123 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-6 Horn ...3-6 Tilt Wheel ...3-6 Turn Signal/Multifunction Lever ...3-7 Turn and Lane-Change Signals ...3-8 Headlamp High/Low-Beam Changer ...3-8 Flash-to-Pass ...3-8 Windshield Wipers ...3-9 Windshield Washer ...3-9 Cruise Control ...3-10 Exterior Lamps ...3-13 Daytime Running Lamps (DRL)/...
Page 124 Section 3 Engine Coolant Temperature Gage ...3-40 Low Coolant Warning Light ...3-41 Malfunction Indicator Lamp ...3-41 Oil Pressure Light ...3-44 Change Engine Oil Light ...3-45 Security Light ...3-45 Cruise Control Light ...3-45 Reduced Engine Power Light ...3-46 Highbeam On Light ...3-46 Headlamps Suggested Light ...3-46 Low Washer Fluid Warning Light ...3-47 Door Ajar Light ...3-47...
Page 125 NOTES...
Page 126: Instrument Panel Overview
Instrument Panel Overview...
Page 127 The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-29. B. Interior Lamps Control. See Interior Lamps on page 3-16. C. Exterior Lamps Control. See Exterior Lamps on page 3-13. Fog Lamp Control. See Fog Lamps on page 3-15 D.
Page 128: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located in the center of the instrument panel.
Page 129: Turn Signal/Multifunction Lever
Telescoping Column A telescoping column on the steering wheel allows adjustment of the distance of the steering wheel and the driver without moving the driver’s seat. The lever on the steering wheel column that enables telescoping is located on the left side of the steering column and behind the tilt lever.
Page 130: Turn And Lane-Change Signals
Turn and Lane-Change Signals To signal a turn, move the lever up or down. The lever returns to its original position when the turn is completed. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change.
Page 131: Windshield Wipers
Windshield Wipers Be sure to clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, gently loosen or thaw them. Damaged wiper blades may not clear the windshield well, making it harder to see and drive safely.
Page 132: Cruise Control
Cruise Control The buttons for the cruise control are located on the steering wheel. (Cruise On/Off): Push this button to turn the system on and off. RES + (Resume/Accelerate): Push this button to make the vehicle resume a previously set speed or to accelerate when cruise is already active.
Page 133 Setting Cruise Control CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Page 134 Reducing Speed While Using Cruise Control There are two ways to reduce your speed while using cruise control: • Press the SET button until you reach the lower speed you want, then release it. • To slow down in very small amounts, brieﬂy press the SET button.
Page 135: Exterior Lamps
Exterior Lamps The control located to the left of the cluster on the instrument panel, operates the exterior lamps. (On/Off): Turn the control to this position to manually turn the headlamps on and off. This is a momentary control that will spring back to AUTO when released.
Page 136: Daytime Running Lamps (Drl)/ Automatic Headlamp System
< (Parking Lamps): Turn the control to this position to turn on the parking lamps together with the following: • Taillamps • License Plate Lamps • Sidemarker Lamps • Instrument Panel Lights (Headlamps): Turn the control to this position to turn your headlamps on, together with the previously listed lamps and lights.
Page 137: Fog Lamps
When it is dark enough outside, the DRL will turn off and the vehicle’s headlamps and parking lamps will turn on. The other lamps that come on with the headlamps will also come on. When it is bright enough outside, the headlamps will go off and the DRL will come on.
Page 138: Interior Lamps
Interior Lamps Your interior lamps control is located next to the exterior lamps control and to the left of the steering wheel on the instrument panel. (Off): Turn the control to this position to disable courtesy lamps, entry lighting, delayed entry lighting, and delayed exit lighting.
Page 139: Delayed Entry Lighting
Entry lighting includes a feature called theater dimming. With theater dimming, the lamps do not turn off at the end of the delay time. Instead, they slowly dim after the delay time and then turn off. The courtesy lamps turn off when the ignition key is turned to RUN or START.
Page 140: Perimeter Lighting
Perimeter Lighting Perimeter lighting provides a period of exterior vehicle lighting. Perimeter lighting activates when the key is removed from the ignition or the vehicle is unlocked using the remote keyless entry transmitter. The amount of time the exterior lamps will remain on can be programmed using the Driver Information Center (DIC).
Page 141: How The System Works
The URPA display is located inside the vehicle, above the rear window. It has three color-coded lights that can be seen through the rearview mirror or by turning around. CAUTION: Even with the Ultrasonic Rear Park Assist system, the driver must check carefully before backing up.
Page 142: Accessory Power Outlet(S)
If the URPA system is not functioning properly, the display will ﬂash red, indicating that there is a problem. The light will also ﬂash red while driving if a trailer is attached to your vehicle, or a bicycle or object is on the back of, or hanging out of your trunk.
Page 143: Ashtray(S) And Cigarette Lighter
Notice: Improper use of the power outlet can cause damage not covered by your warranty. Do not hang any type of accessory or accessory bracket from the plug because the power outlets are designed for accessory power plugs only. Notice: Leaving electrical equipment on for extended periods will drain the battery.
Page 144: Climate Controls
Climate Controls Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. If your vehicle has the remote start feature and it is activated, the climate control system will automatically cool the vehicle if the temperature is greater than 90°F (32°C) and heat the vehicle if the temperature is below 37°F (3°C).
Page 145 Use the right knob to select from the following modes: (Vent): This mode directs outside air to the instrument panel outlets. If driving in city traffic, and the vehicle is stopped and idling, or the weather is hot, turn on the recirculation mode. To prevent the air inside the vehicle from becoming stale, after ﬁve minutes recirculate will allow outside air into the vehicle.
Page 146: Defogging And Defrosting
On hot days during the vehicle’s initial start-up, open the windows to let hot inside air escape; then close them. This helps to reduce the time it takes for the vehicle to cool down. It also helps the system to operate more efficiently.
Page 147: Dual Automatic Climate Control System
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. < (Rear): Press the button to turn the rear window defogger on or off. An indicator light below the button will come on to let you know that the rear window defogger is activated.
Page 148 For the automatic system to function, the temperature must be set between 61°F (15°C) and 89°F (32°C). 1. Adjust the temperature to a comfortable setting. 2. Press the PASS button or the up or down arrows on the passenger side to turn the passenger temperature set on and off.
Page 149 Manual Operation During daylight hours, the instrument panel brightness control might need to be adjusted to the highest setting, in order to see the indicator lights for the various climate control settings. OFF: Press this button to turn the climate control system off.
Page 150 (Recirculation): Press this button to turn recirculation mode on or off. This mode keeps outside air from coming into the vehicle. It can be used to prevent outside air and odors from entering your vehicle or to help cool the air inside the vehicle more quickly. Recirculation is not available while in the ﬂoor, defrost, or ﬂoor/defog modes.
Page 151: Outlet Adjustment
Sensors The solar sensor on the vehicle monitors the solar heat and the air inside of the vehicle. This information is used to maintain the selected temperature by initiating needed adjustments to the temperature, the fan speed, and the air delivery system. The system may also supply cooler air to the side of the vehicle facing the sun.
Page 152: Passenger Compartment Air Filter
Passenger Compartment Air Filter The passenger compartment air ﬁlter is located below the air inlet grille, near the passenger’s side windshield wiper arm. See Engine Compartment Overview on page 5-12. The ﬁlter traps most of the pollen from the air entering the air conditioning module.
Page 153: Steering Wheel Climate Controls
Steering Wheel Climate Controls If your vehicle has this feature, you can control the driver’s temperature setting by using the control located on your steering wheel. (Temperature): Press the up arrow to increase or the down arrow decrease the temperature inside your vehicle.
Page 154: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster is designed to let the driver know at a glance how the vehicle is running. It will show how fast the vehicle is going, about how much fuel is in the fuel tank and many other things needed to drive safely and economically.
Page 155: Speedometer And Odometer
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your vehicle’s odometer works together with the driver information center. You can set a Trip A and Trip B odometer. See “Trip Information” under DIC Operation and Displays on page 3-50.
Page 156: Passenger Safety Belt Reminder Light
Passenger Safety Belt Reminder Light Several seconds after the key is turned to RUN or START, a chime will sound for several seconds to remind the front passenger to buckle their safety belt. This would only occur if the passenger airbag is enabled.
Page 157: Passenger Airbag Status Indicator
CAUTION: If the airbag readiness light stays on after you start your vehicle, it means the airbag system may not be working properly. The airbags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash.
Page 158 If the word ON is lit on the passenger airbag status indicator, it means that the right front passenger’s frontal airbag is enabled (may inﬂate). CAUTION: If the on indicator comes on when you have a rear-facing child restraint installed in the right front passenger’s seat, it means that the passenger sensing system has not turned off the passenger’s frontal airbag.
Page 159: Charging System Light
If, after several seconds, all status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer for service. CAUTION: If the off indicator and the airbag readiness light ever come on together, it means that something may be wrong with the airbag system.
Page 160: Brake System Warning Light
Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on and the parking brake is not applied, there is a brake problem.
Page 161: Anti-Lock Brake System Warning Light
Anti-Lock Brake System Warning Light Your vehicle may have the anti-lock brake system, this light will come on when your engine is started and may stay on for several seconds. That is normal. If the ABS warning light comes on and stays on, there may be a problem with the anti-lock portion of the brake system.
Page 162: Engine Coolant Temperature Warning Light
Engine Coolant Temperature Warning Light This light tells you that your engine is very hot. This light will come on when you ﬁrst start the vehicle as a check to let you know that the light is working. It will go out after a few seconds.
Page 163: Low Coolant Warning Light
Low Coolant Warning Light If equipped, this light comes on brieﬂy when you turn your ignition on as a bulb check only. Malfunction Indicator Lamp Check Engine Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition, and emission control systems.
Page 164: If The Light Is On Steady
This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light does not come on, have it repaired. This light will also come on during a malfunction in one of two ways: •...
Page 165 Did you just drive through a deep puddle of water? If so, your electrical system may be wet. The condition will usually be corrected when the electrical system dries out. A few driving trips should turn the light off. Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel.
Page 166: Maintenance Schedule
Oil Pressure Light Your vehicle may have this feature. If the vehicle has an oil problem, this light may stay on after the engine is started, or come on while you are driving. This light indicates that oil is not going through the engine quickly enough to keep it lubricated.
Page 167: Change Engine Oil Light
Change Engine Oil Light If this light comes on, it means that service is required for your vehicle. See Scheduled Maintenance on page 6-4 and Engine Oil on page 5-15 for more information. After having the oil changed you will need to reset the light.
Page 168: Reduced Engine Power Light
Reduced Engine Power Light If the reduced engine power light is on, a chime will sound and a noticeable reduction in the vehicle’s performance may occur. If the reduced engine power light is on, but there is no reduction in performance, proceed to your destination. The performance may be reduced the next time the vehicle is driven.
Page 169: Low Washer Fluid Warning Light
Low Washer Fluid Warning Light This light will come on brieﬂy when the ignition is on. If the light stays on, a chime will sound indicating your windshield washer ﬂuid is low. See Windshield Washer Fluid on page 5-38 for more information.
Page 170: Fuel Gage
Fuel Gage The fuel gage indicates about how much fuel is left in the fuel tank when the ignition is on. When the indicator nears empty, there is still a little fuel left, but you should get more fuel soon. Here are four things that some owners ask about.
Page 171: Driver Information Center (Dic)
Driver Information Center (DIC) Your vehicle may have a Driver Information Center (DIC). All messages will appear in the DIC display located in the instrument panel cluster, below the speedometer. The DIC buttons are located on the center of the instrument panel, below the center outlets.
Page 172: Dic Operation And Displays
DIC Operation and Displays The DIC has different modes which can be accessed by pressing the DIC buttons located on the center of the instrument panel. Depending on whether your vehicle has the base level or uplevel DIC, the buttons and modes available will differ.
Page 173 (Gages)*: Press this button to display the battery voltage and oil life. (Set/Reset)*: Press this button to set or reset certain functions and to turn off or acknowledge messages on the DIC. (Option)*: Press this button to display the units, language, personalization, compass zone, and compass calibration.
Page 174 There is also a retroactive trip odometer function that performs the following for each trip odometer: • If the vehicle’s speed has exceeded 3 mph (5 km/h) during the current ignition cycle, this function will set the trip odometer to the distance driven during the current ignition cycle.
Page 175 Fuel Menu Items (Uplevel Only) (Fuel): Press this button to scroll through the following menu items: Fuel Range Press the fuel button until FUEL RANGE displays. This mode shows the approximate number of remaining miles or kilometers the vehicle can be driven without refueling.
Page 176: Oil Life
Gages Menu Items (Uplevel Only) (Gages): Press this button to scroll through the following menu items: Battery Press the gages button until BATTERY displays. This mode shows the current battery voltage. If there is a problem with the battery charging system, a DIC message will display.
Page 177 Option Menu Items (Uplevel Only) (Option): Press this button to scroll through the following menu items: Units Press the option button until UNITS displays. This mode allows you to select between English or Metric units of measurement. Once in this mode, press the set/reset button to select between ENGLISH or METRIC units.
Page 178: Compass Calibration
To adjust for compass variance, use the following procedure: Compass Variance Procedure 1. Press the option button until COMPASS ZONE displays. 2. Find the vehicle’s current location and variance zone number on the map. Zones 1 through 15 are available. 3-56 3.
Page 179: Dic Warnings And Messages
DIC Warnings and Messages Messages are displayed on the uplevel DIC to notify the driver that the status of the vehicle has changed and that some action may be needed by the driver to correct the condition. Multiple messages may appear one after another.
Page 180: Battery Saver Active
BATTERY SAVER ACTIVE This message will display when the system detects that the battery voltage is dropping beyond a reasonable level. The battery saver system will start reducing certain features of the vehicle that you may be able to notice. At the point that the features are disabled, this message is displayed.
Page 181: Delayed Locking
This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on.
Page 182: Engine Coolant Hot
This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on.
Page 183: Headlamps Suggested
This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on.
Page 184: Key In Ignition
This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on.
Page 185: Low Fuel
LEFT REAR TURN LAMP OUT This message will display when the left rear turn signal bulb needs to be replaced. See Taillamps, Turn Signal, Sidemarker, Stoplamps and Back-up Lamps on page 5-54. This message will display while the ignition is in RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen.
Page 186 LOW OIL LEVEL This message will display when the vehicle’s engine oil is low. Fill the oil to the proper level as soon as possible. See Engine Compartment Overview on page 5-12 for the engine oil ﬁll location. Also, see Engine Oil on page 5-15 for information on the kind of oil to use and the proper oil level.
Page 187 LOW WASHER FLUID This message will display when the windshield washer ﬂuid is low. Fill the windshield washer reservoir as soon as possible. See Engine Compartment Overview on page 5-12 for the location of the windshield washer reservoir. Also, see Windshield Washer Fluid on page 5-38 for more information.
Page 188: Reduced Engine Power
PASSENGER’S DOOR AJAR This message will display when the front passenger’s door is not closed properly. When this message appears, you should make sure that the front passenger’s door is closed completely. This message will display while the ignition is in RUN. A chime will sound when the ignition is shifted out of PARK (P).
Page 189 This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off. It will also re-display for two seconds if the message has been acknowledged, but the condition still exists when the engine is turned off. If the condition still exists, the message will re-appear when the engine is turned on.
Page 190: Service Abs System
RIGHT FRONT TURN LAMP OUT This message will display when the right front turn signal bulb needs to be replaced. See Front Turn Signal and Parking Lamps on page 5-53. This message will display while the ignition is in RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen.
Page 191: Service Brake System
SERVICE BRAKE SYSTEM This message will display when a problem with the brake system has been detected. Have your vehicle serviced by your GM dealer as soon as possible. The brake system warning light will also appear on the instrument panel cluster when this message appears on the DIC.
Page 192: Service Traction System
This message will display only while the ignition is in RUN. Press any of the DIC buttons to acknowledge this message and to clear it from the screen. This message will continue to display for two seconds if it has not been acknowledged when the engine is turned off.
Page 193: Service Variable Effort Steering
SERVICE VARIABLE EFFORT STEERING If your vehicle has variable effort steering, this message will display when if this system is not functioning properly. See Steering on page 4-11 for more information. Have your system serviced by your GM dealer as soon as possible. This message will display only while the ignition is in RUN.
Page 194: Stability Control Off
STABILITY CONTROL OFF ® If your vehicle has StabiliTrak , this message will display any time the system turns off. When this message has been displayed, StabiliTrak longer available to assist you with directional control of the vehicle. Adjust your driving accordingly. ®...
Page 195: Turn Signal On
Any of the following conditions may cause the traction control system to turn off: • The traction control system is turned off by pressing the traction control button located on the center of the instrument panel. See Traction Control System (TCS) on page 4-10. •...
Page 196 Your vehicle may also have personalization capabilities that allow you to program certain features to a preferred setting for up to two drivers. The ﬁrst personalized key corresponds to driver 1 and the second personalized key corresponds to driver 2. The personalization features include the following: •...
Page 197 Customization Menu Items The following are customization features that allow you to program settings to the vehicle: FACTORY DEFAULTS This feature allows you to set all of the customization and personalization features back to their factory default settings. Press the option button until FACTORY DEFAULTS appears on the DIC display.
Page 198 60 seconds: The exterior lamps will stay on for 60 seconds. 90 seconds: The exterior lamps will stay on for 90 seconds. Select one of the available choices and press the option button while it is displayed on the DIC to select it and move on to the next feature.
Page 199 If a key is in the ignition, this feature will not lock the doors. See Delayed Locking on page 2-11 for more information. Press the option button until DELAYED LOCKING appears on the DIC display. Press the set/reset button to scroll through the following choices: OFF: There will be no delayed locking of the vehicle’s doors.
Page 200 FOB LOCK FEEDBACK This feature allows you to select the type of feedback you will receive when locking the vehicle with the remote keyless entry transmitter. Press the option button until FOB LOCK FEEDBACK appears on the DIC display. Press the set/reset button to scroll through the following choices: OFF: There will be no feedback when locking the vehicle.
Page 201 Personalization Menu Items The following are personalization features that allow you to program setting for up to two drivers: PERSONALIZE KEY This feature allows you to personalize a key to be recognized as key 1 or 2. A personalized key allows you to program personalization features to a preferred setting to correspond to key 1 or 2.
Page 202 AUTO DOOR LOCK This feature allows automatic door locking to be turned OFF or ON. Press the option button until AUTO DOOR LOCK appears on the DIC display. Press the set/reset button to scroll through the following choices: OFF: All automatic door locking is disabled. The doors will always need to be locked manually before driving, to increase occupant safety.
Page 203 Press the option button until AUTO UNLOCK ON appears on the DIC display. Press the set/reset button to scroll through the following choices: KEY-OUT: The door(s) will unlock when the key is taken out of the ignition. PARK (default): The door(s) will unlock when the vehicle is shifted into PARK (P).
Page 204: Audio System(S)
Audio System(s) Determine which radio your vehicle has and then read the pages following to familiarize yourself with its features. Driving without distraction is a necessity for a safer driving experience. See Defensive Driving on page 4-2. By taking a few moments to read this manual and get familiar with your vehicle’s audio system, you can use it with less effort, as well as take advantage of its features.
Page 205: Setting The Time
Here are some ways in which you can help avoid distraction while driving. While your vehicle is parked: • Familiarize yourself with all of its controls. • Familiarize yourself with its operation. • Set up your audio system by presetting your favorite radio stations, setting the tone, and adjusting the speakers.
Page 206: Radio With Cd (Base)
Radio with CD (Base) Playing the Radio (Power): Press this knob to turn the system on and off. (Volume): Turn this knob to increase or to decrease the volume. 3-84 DISP (Display): Press this button to switch the display between the radio station frequency, band, and time of day.
Page 207: Setting Preset Stations
To scan preset stations, press and hold either arrow for more than four seconds. PSC will appear on the display and the radio will produce two beeps. The radio will go to a preset station, play for a few seconds, then go on to the next preset station.
Page 208: Playing A Cd
To adjust the balance and the fade to the middle position, push the speaker knob, then push it again and hold it until you hear one beep. To adjust all tone and speaker controls to the middle position, push and hold the speaker knob when no tone or speaker control is displayed.
Page 209 If there is no apparent damage, try a known good CD. Do not add any label to a CD, it could get caught in the CD player. If a CD is recorded on a personal computer and a description label is needed, try labeling the top of the recorded CD with a marking pen instead.
Page 210: Radio With Cd (Uplevel)
CD Messages CHECK CD: If this message appears on the display and/or the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. •...
Page 211: Playing The Radio
Playing the Radio (Power): Press this knob to turn the system on and off. (Volume): Turn this knob to increase or to decrease the volume. DISP (Display): When the ignition is turned off, press this button to display the time. For XM™...
Page 212 To scan preset stations, press and hold either arrow for more than four seconds. PSCAN will appear on the display and the radio will produce two beeps. The radio will go to a preset station, play for a few seconds, then go on to the next preset station.
Page 213 Setting the Tone (Bass/Treble) (Bass/Treble): Push and release this knob until BASS or TREBLE appears on the display. Turn this knob to increase or to decrease. The display will show the bass or the treble level. If a station is weak or noisy, decrease the treble.
Page 214 Finding a Category (CAT) Station (XM™ Satellite Radio Service Only) To select and ﬁnd a desired category perform the following: 1. Press the CAT button to activate category select mode. The current category will appear on the display. 2. Turn the tune knob to select a category. 3.
Page 215 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. Updating Updating encryption code No Signl Loss of signal Loading Acquiring channel audio (after 4 second delay) Off Air Channel not in service CH Unavl Channel no longer...
Page 216 Radio Display Message No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Lock Theft lock active Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Check XM...
Page 217 Playing a CD Insert a CD partway into the slot, label side up. The player will pull it in and the CD should begin playing. If you want to insert a CD with the ignition off, ﬁrst press the eject button or the DISP knob. If the ignition or radio is turned off with a CD in the player it will stay in the player.
Page 218 (Fast Forward): Press this pushbutton to go to the next track. The fast forward symbol and the track number will appear on the display. If this pushbutton is held or pressed more than once, the player will continue moving forward through the CD. 4 RDM (Random): Press this pushbutton to hear the tracks in random, rather than sequential, order.
Page 219: Radio With Cd (Mp)
CD Messages CHECK CD: If this message appears on the display and/or the CD comes out, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. •...
Page 220 Playing the Radio (Power): Press this knob to turn the system on and off. (Volume): Turn this knob to increase or to decrease the volume. DISP (Display): Press this button to switch the display between the radio station frequency and time of day. When the ignition is turned off, press this knob to display the time.
Page 221 To scan preset stations, press and hold either arrow for more than four seconds. PSCAN will appear on the display and the radio will produce two beeps. The radio will go to a preset station, play for a few seconds, then go on to the next preset station.
Page 222 Setting the Tone (Bass/Treble) (Bass/Treble): Push and release this knob until BASS or TREBLE appears on the display. Turn this knob to increase or to decrease. The display will show the bass or the treble level. If a station is weak or noisy, decrease the treble.
Page 223 Finding a Category (CAT) Station (XM™ Satellite Radio Service Only) To select and ﬁnd a desired category perform the following: 1. Press the CAT button to activate category select mode. The current category will appear on the display. 2. Turn the tune knob to select a category. 3.
Page 224 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. Updating Updating encryption code No Signl Loss of signal Loading Acquiring channel audio (after 4 second delay) Off Air Channel not in service CH Unavl Channel no longer...
Page 225 Radio Display Message No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Lock Theft lock active Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Check XM...
Page 226 Playing a CD Insert a CD partway into the slot, label side up. The player will pull it in and the CD should begin playing. If you want to insert a CD with the ignition off, ﬁrst press the eject button or the DISP knob. If the ignition or radio is turned off with a CD in the player it will stay in the player.
Page 227: Mp3 Format
4 RDM (Random): Press this pushbutton to hear the tracks in random, rather than sequential, order. RANDOM ON will appear on the display. Press this pushbutton again to turn off random play. SEEK : Press the left arrow to go to the start of the current or the previous track.
Page 228 The player will be able to read and play a maximum of 50 folders, 50 playlists, 10 sessions, and 255 ﬁles. Long ﬁle names, folder names, or playlist names may use more disc memory space than necessary. To conserve space on the disc, minimize the length of the ﬁle, folder or playlist name.
Page 229 Order of Play Tracks will be played in the following order: • Play will begin from the ﬁrst track in the ﬁrst playlist and will continue sequentially through all tracks in each playlist. When the last track of the last playlist has been played, play will continue from the ﬁrst track of the ﬁrst playlist.
Page 230 If the ignition or radio is turned off with a CD in the player it will stay in the player. When the ignition or radio is turned on, the CD will start to play where it stopped, if it was the last selected audio source. The CD player can play the smaller 3 inch (8 cm) single CDs with an adapter ring.
Page 231 4 RDM (Random): Press this pushbutton to hear tracks in random, rather than sequential order. You can random the entire folder, playlist, or CD. Press and release this pushbutton until RANDOM FOLDER, RANDOM P-LIST, or RANDOM DISC appears on the display. Once all of the tracks in the current folder or playlist have been played the system will move on to the next folder or playlist and play all of the tracks in random order.
Page 232 To change the default on the display, press the DISP knob until you see the display you want, then hold this knob for two seconds. The radio will produce one beep and the selected display will now be the default. INFO (Information): INFO will appear on the display whenever a current track has ID3 tag information.
Page 233: Radio With Six-Disc Cd
Radio with Six-Disc CD XM™ Satellite Radio Service XM™ is a satellite radio service that is based in the 48 contiguous Untied States and in Canada (if available). XM™ offers over 100 coast-to-coast channels including music, news, sports, talk, and children’s programming. XM™...
Page 234 Set the volume at the desired level. Press this button to select LOW, MEDIUM, or HIGH. Each higher setting will allow for more volume compensation at faster vehicle speeds. Then as you drive, SCV increases the volume, as necessary, to overcome noise at any speed.
Page 235 Once the complete message has been displayed, the information symbol will disappear from the display until another new message is received. The last message can be displayed by pressing the INFO button. You can view the last message until a new message is received or a different station is tuned to.
Page 236 Adjusting the Speakers (Balance/Fade) (Balance/Fade): To adjust the balance between the right and the left speakers, push and release this knob until BAL appears on the display. Turn the knob to move the sound toward the right or the left speakers. To adjust the fade between the front and the rear speakers, push and release the speaker knob until FADE appears on the display.
Page 237 Scanning Categories (CAT) (XM™ Satellite Radio Service Only) To scan a desired category perform the following: 1. Press the CAT button to activate category select mode. The current category will appear on the display. 2. Turn the tune knob to select a category. 3.
Page 238 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. Updating Updating encryption code No Signl Loss of signal Loading Acquiring channel audio (after 4 second delay) Off Air Channel not in service CH Unavl Channel no longer...
Page 239 Radio Display Message No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Lock Theft lock active Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Check XM...
Page 240 Playing a CD If the ignition or radio is turned off, with a CD in the player, it will stay in the player. When the ignition or radio is turned on, the CD will start playing where it stopped, if it was the last selected audio source. When a CD is inserted, the CD symbol will appear on the CD.
Page 241 To insert multiple CDs, do the following: 1. Turn the ignition on. 2. Press and hold the LOAD button for two seconds. You will hear a beep and the indicator light, located to the right of the slot, will begin to ﬂash and MULTI LOAD # will appear on the display.
Page 242 If the CD is not removed, after 25 seconds, the CD will be automatically pulled back into the player. If CD is pushed back into the player, before the 25 second time period is complete, the player will sense an error and will try to eject the CD several times before stopping.
Page 243 SEEK : Press the left arrow to go to the start of the current track, if more than ten seconds have played. Press the right arrow to go to the next track. If either arrow is held or pressed more than once, the player will continue moving backward or forward through the CD.
Page 244 Using List Mode The six-disc CD changer has a feature called song list. This feature is capable of saving 20 track selections. To save tracks into the song list feature, perform the following steps: 1. Turn the CD player on and load it with at least one CD.
Page 245 To delete the entire song list, perform the following steps: 1. Turn the CD player on. 2. Press the LIST button to turn song list on. LIST will appear on the display. 3. Press and hold the LIST button for more than four seconds.
Page 246: Audio Steering Wheel Controls
Theft-Deterrent Feature ® THEFTLOCK is designed to discourage theft of your vehicle’s radio. The feature works automatically by learning a portion of the Vehicle Identiﬁcation Number (VIN). If the radio is moved to a different vehicle, it will not operate and LOC or LOCKED will appear on the display.
Page 247 To scan stations, press and hold either arrow for more than two seconds. SCAN will appear on the display and the radio will produce one beep. The radio will go to a station, play for a few seconds, then go on to the next station.
Page 248: Radio Reception
Radio Reception You may experience frequency interference and static during normal radio reception if items such as cellphone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet. The range for most AM stations is greater than for FM, especially at night.
Page 249: Care Of The Cd Player
Care of the CD Player The use of CD lens cleaners for CD players is not advised, due to the risk of contaminating the internal lens of the CD optics with lubricants. Backglass Antenna The AM-FM antenna is integrated with the rear window defogger, located in the rear window.
Page 250: Xm™ Satellite Radio Antenna System
XM™ Satellite Radio Antenna System The XM™ Satellite Radio antenna is located on the roof of your vehicle. Keep this antenna clear of snow and ice build up for clear radio reception. If your vehicle has a sunroof, the performance of the XM™...
Page 251: Driving Your Vehicle
Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Defensive Driving ...4-2 Drunken Driving ...4-3 Control of a Vehicle ...4-6 Braking ...4-6 Anti-Lock Brake System (ABS) ...4-7 Braking in Emergencies ...4-9 Traction Control System (TCS) ...4-10 ® StabiliTrak System ...4-11 Steering ...4-11 Off-Road Recovery ...4-13 Passing ...4-14...
Page 252: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-8. CAUTION: Defensive driving really means “Be ready for anything.”...
Page 253: Drunken Driving
Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It is the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol affects four things that anyone needs to drive a vehicle: •...
Page 254 According to the American Medical Association, a 180 lb (82 kg) person who drinks three 12 ounce (355 ml) bottles of beer in an hour will end up with a BAC of about 0.06 percent. The person would reach the same BAC by drinking three 4 ounce (120 ml) glasses of wine or three mixed drinks if each had 1-1/2 ounces (45 ml) of liquors like whiskey, gin, or vodka.
Page 255 Statistics show that the chance of being in a collision increases sharply for drivers who have a BAC of 0.05 percent or above. A driver with a BAC level of 0.06 percent has doubled his or her chance of having a collision.
Page 256: Control Of A Vehicle
Control of a Vehicle You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering, and the accelerator. All three systems have to do their work at the places where the tires meet the road.
Page 257: Anti-Lock Brake System (Abs)
Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking.
Page 258 Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel.
Page 259: Braking In Emergencies
Remember: Anti-lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
Page 260: Traction Control System (Tcs)
Traction Control System (TCS) Your vehicle may have a Traction Control System (TCS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that one or both of the front wheels are spinning or beginning to lose traction.
Page 261: Stabilitrak System
® StabiliTrak System Your vehicle may be equipped with a vehicle stability enhancement system called StabiliTrak advanced computer controlled system that assists you with directional control of the vehicle in difficult driving conditions. ® StabiliTrak activates when the computer senses a discrepancy between your intended path and the direction the vehicle is actually traveling.
Page 262: Steering In Emergencies
The traction you can get in a curve depends on the condition of your tires and the road surface, the angle at which the curve is banked, and your speed. While you are in a curve, speed is the one factor you can control. Suppose you are steering through a sharp curve.
Page 263: Off-Road Recovery
An emergency like this requires close attention and a quick decision. If you are holding the steering wheel at the recommended 9 and 3 o’clock positions, you can turn it a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
Page 264: Passing
Passing The driver of a vehicle about to pass another on a two-lane highway waits for just the right moment, accelerates, moves around the vehicle ahead, then goes back into the right lane again. A simple maneuver? Not necessarily! Passing another vehicle on a two-lane highway is a potentially dangerous move, since the passing vehicle occupies the same lane as oncoming traffic for several seconds.
Page 265: Loss Of Control
Remember that your passenger side outside mirror is convex. The vehicle you just passed may seem to be farther away from you than it really is. • Try not to pass more than one vehicle at a time on two-lane roads. Reconsider before passing the next vehicle.
Page 266: Driving At Night
Of course, traction is reduced when water, snow, ice, gravel, or other material is on the road. For safety, you will want to slow down and adjust your driving to these conditions. It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited.
Page 267: Driving In Rain And On Wet Roads
What you do in the daytime can also affect your night vision. For example, if you spend the day in bright sunshine you are wise to wear sunglasses. Your eyes will have less trouble adjusting to night. But if you are driving, do not wear sunglasses at night.
Page 268 The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road, and even people walking.
Page 269: Driving Through Deep Standing Water
Driving Through Deep Standing Water Notice: If you drive too quickly through deep puddles or standing water, water can come in through your engine’s air intake and badly damage your engine. Never drive through water that is slightly lower than the underbody of your vehicle. If you cannot avoid deep puddles or standing water, drive through them very slowly.
Page 270: City Driving
City Driving One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals. 4-20 Here are ways to increase your safety in city driving: •...
Page 271: Freeway Driving
Freeway Driving Mile for mile, freeways — also called thruways, parkways, expressways, turnpikes, or superhighways — are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 272: Before Leaving On A Long Trip
Once you are moving on the freeway, make certain you allow a reasonable following distance. Expect to move slightly slower at night. When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up.
Page 273: Highway Hypnosis
Here are some things you can check before a trip: • Windshield Washer Fluid: Is the reservoir full? Are all windows clean inside and outside? • Wiper Blades: Are they in good shape? • Fuel, Engine Oil, Other Fluids: Have you checked all levels? •...
Page 274: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or mountains is different from driving in ﬂat or rolling terrain. 4-24 If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable.
Page 275 CAUTION: Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. Your brakes will have to do all the work of slowing down. They could get so hot that they would not work well. You would then have poor braking or even none going down a hill.
Page 276: Winter Driving
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your trunk. Also see Tires on page 5-57. 4-26 Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth, and a couple of reﬂective warning triangles.
Page 277: Driving On Snow Or Ice
Driving on Snow or Ice Most of the time, those places where the tires meet the road probably have good traction. However, if there is snow or ice between the tires and the road, you can have a very slippery situation. You will have a lot less traction, or grip, and will need to be very careful.
Page 278: If You Are Caught In A Blizzard
Remember, unless you have ABS, if you brake so hard that your wheels stop rolling, you will just slide. Brake so your wheels always keep rolling and you can still steer. • Whatever your braking system, allow greater following distance on any slippery road. •...
Page 279 You can run the engine to keep warm, but be careful. CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You cannot see it or smell it, so you might not know it is in your vehicle.
Page 280: If Your Vehicle Is Stuck In Sand, Mud, Ice Or Snow
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can.
Page 281: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. If your vehicle has traction control, you should turn your traction control system off. See Traction Control System (TCS) on page 4-10.
Page 282 Tire and Loading Information Label Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the vehicle’s center pillar (B-pillar). With the driver’s door open, you will ﬁnd the label attached below the door lock post (striker). 4-32 The tire and loading information label lists the number of occupant seating positions (A), and the maximum...
Page 283 4. The resulting ﬁgure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs and there will be ﬁve 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 750 (5 x 150) = 650 lbs).
Page 284 Example 2 Item Description Maximum Vehicle Capacity Weight for Example 2 Subtract Occupant Weight 150 lbs (68 kg) Available Cargo Weight 4-34 Total Item 1,000 lbs (453 kg) 750 lbs (340 kg) 250 lbs (113 kg) Refer to your vehicle’s tire and loading information label for speciﬁc information about your vehicle’s maximum vehicle capacity weight and seating positions.
Page 285 Certiﬁcation Label A vehicle speciﬁc Certiﬁcation label is found on the rear edge of the driver’s door. The label shows the gross weight capacity of your vehicle, called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo.
Page 286: Towing
If things like suitcases, tools, packages, or anything else are put inside the vehicle, they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going. CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop or turn,...
Page 287: Dolly Towing
Here are some important things to consider before you do recreational vehicle towing: • What is the towing capacity of the towing vehicle? Be sure you read the tow vehicle manufacturer’s recommendations. • How far will you tow? Some vehicles have restrictions on how far and how long they can tow.
Page 288: Towing A Trailer
Towing a Trailer CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all.
Page 289: Weight Of The Trailer
Ask your dealer for our trailering information or advice, or you can write us at: Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-5136 In Canada, write to:...
Page 290: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of the vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo in it, and the people who will be riding in the vehicle.
Page 291: Safety Chains
Total Weight on Your Vehicle’s Tires Be sure the vehicle’s tires are inﬂated to the upper limit for cold tires. These numbers can be found on the Tire-Loading Information label. See Loading Your Vehicle on page 4-31. Be sure not to go over the GVW limit for the vehicle, or the GAWR, including the weight of the trailer tongue.
Page 292: Driving With A Trailer
Driving with a Trailer Towing a trailer requires a certain amount of experience. Before setting out for the open road, get to know the rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle is now a good deal longer and not nearly as responsive as the vehicle is by itself.
Page 293: Turn Signals When Towing A Trailer
Turn Signals When Towing a Trailer When towing a trailer, the vehicle may need a different turn signal ﬂasher and/or extra wiring. Check with your dealer. The arrows on the instrument panel will ﬂash whenever signaling a turn or lane change. Properly hooked up, the trailer lamps will also ﬂash, telling other drivers you are about to turn, change lanes or stop.
Page 294: Maintenance When Trailer Towing
When You Are Ready to Leave After Parking on a Hill 1. Apply the regular brakes and hold the pedal down while you: • Start the engine. • Shift into a gear. • Release the parking brake. 2. Let up on the brake pedal. 3.
Page 295: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-4 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of Your Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-6 California Fuel ...5-6 Additives ...5-6 Fuels in Foreign Countries ...5-7 Filling the Tank ...5-8 Filling a Portable Fuel Container ...5-10...
Page 296 Section 5 Wheel Replacement ...5-70 Tire Chains ...5-72 If a Tire Goes Flat ...5-72 Changing a Flat Tire ...5-73 Removing the Spare Tire and Tools ...5-74 Removing the Flat Tire and Installing the Spare Tire ...5-76 Storing a Flat or Spare Tire and Tools ...5-82 Compact Spare Tire ...5-83 Appearance Care ...5-84 Cleaning the Inside of Your Vehicle ...5-84...
Page 297: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Page 298: California Proposition 65 Warning
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many ﬂuids, and some component wear by-products contain and/or emit these chemicals.
Page 299: Adding Equipment To The Outside
Your vehicle has an airbag system. Before attempting to do your own service work, see Servicing Your Airbag-Equipped Vehicle on page 1-65. You should keep a record with all parts receipts and list the mileage and the date of any service work you perform.
Page 300: Gasoline Speciﬁcations
Gasoline Speciﬁcations At a minimum, gasoline should meet ASTM speciﬁcation D 4814 in the United States or CAN/CGSB-3.5 in Canada. Some gasolines may contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). General Motors recommends against the use of gasolines containing MMT. See Additives on page 5-6 for additional information.
Page 301: Fuels In Foreign Countries
In most cases, you should not have to add anything to your fuel. However, some gasolines contain only the minimum amount of additive required to meet U.S. Environmental Protection Agency regulations. To help keep fuel injectors and intake valves clean, or if your vehicle experiences problems due to dirty injectors or valves, look for gasoline that is advertised as TOP TIER Detergent Gasoline.
Page 302: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 303 CAUTION: If you spill fuel and then something ignites it, you could be badly burned. Fuel can spray out on you if you open the fuel cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather. Open the fuel cap slowly and wait for any hiss noise to stop.
Page 304: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: •...
Page 305: Hood Release
Hood Release To open the hood, do the following: 1. Pull the interior hood release handle with this symbol on it. It is located to the left of the steering column below the instrument panel. 2. Push the secondary hood release lever, located under the center of the hood above the grille, up and to the right to disengage it.
Page 306: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 3.6L V6 engine, here is what you will see: 5-12...
Page 307 A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-38. B. Battery. See Battery on page 5-42. C. Remote Positive (+) Terminal. See Jump Starting on page 5-42. D. Underhood Fuse Block. See Underhood Fuse Block on page 5-95.
Page 308 When you open the hood on the 3.8L V6 engine, here is what you will see: 5-14...
Page 309: Engine Oil
A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-38. B. Battery. See Battery on page 5-42. C. Remote Positive (+) Terminal. See Jump Starting on page 5-42. D. Passenger Compartment Air Filter. See Passenger Compartment Air Filter on page 3-30.
Page 310: When To Add Engine Oil
When to Add Engine Oil 3.6L V6 Engine 3.8L V6 Engine If the oil is below the cross-hatched area at the tip of the dipstick, you will need to add at least one quart/liter of oil. But you must use the right kind. This section explains what kind of oil to use.
Page 311: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Look for two things: • GM6094M Your vehicle’s engine requires oil meeting GM Standard GM6094M. You should look for and use only an oil that meets GM Standard GM6094M. • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle.
Page 312: Engine Oil Life System
If you are in an area of extreme cold, where the temperature falls below 20°F ( 29°C), it is recommended that you use either an SAE 5W-30 synthetic oil or an SAE 0W-30 oil. Both will provide easier cold starting and better protection for your engine at extremely low temperatures.
Page 313: What To Do With Used Oil
After changing the engine oil, reset the system by performing the following steps: • Vehicles with Driver Information Center (DIC) 1. Press the option button on the DIC until ENGINE OIL MONITOR appears on the DIC screen. 2. Press the set/reset button to reset the system. The next screen indicates that the CHANGE OIL SOON message has been reset.
Page 314: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter 3.6L V6 Engine shown, 3.8L V6 Engine similar The engine air cleaner/ﬁlter is located in the engine compartment on the driver’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location. 5-20 When to Inspect the Engine Air Cleaner/Filter...
Page 315: Automatic Transaxle Fluid
5. To reinstall the cover, position the tabs through the slots on the housing. A notch on the sides of the ﬁlter cover will indicate the correct engagement. 6. Push the cover tabs on top of the housing to lock the cover in place.
Page 316: How To Check Automatic Transaxle Fluid
How to Check Automatic Transaxle Fluid Because this operation can be a little difficult, you may choose to have this done at the dealership service department. If you do it yourself, be sure to follow all the instructions here, or you could get a false reading on the dipstick. Notice: Too much or too little ﬂuid can damage the transaxle.
Page 317 Then, without shutting off the engine, follow these steps: The transaxle ﬂuid dipstick handle has this symbol on it, and is located near the rear of the engine compartment. See Engine Compartment Overview on page 5-12 for more information on location. 1.
Page 318: Engine Coolant
Engine Coolant The cooling system in the vehicle is ﬁlled with ® DEX-COOL engine coolant. This coolant is designed to remain in the vehicle for ﬁve years or 150,000 miles (240 000 km), whichever occurs ﬁrst, ® if only DEX-COOL extended life coolant is added.
Page 319 CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning.
Page 320: Checking Coolant
Checking Coolant The coolant recovery tank is located in the engine compartment toward the rear of the engine on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location. 3.8L V6 Engine shown, 3.6L V6 Engine similar The vehicle must be on a level surface when checking...
Page 321: Radiator Pressure Cap
CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Occasionally check the coolant level in the radiator. For information on how to add coolant to the radiator, see Cooling System on page 5-30.
Page 322: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
Page 323: Overheated Engine Protection
If you get the overheat warning with no sign of steam, try this for a minute or so: 1. In heavy traffic, let the engine idle in NEUTRAL (N) while stopped. If it is safe to do so, pull off the road, shift to PARK (P) or NEUTRAL (N) and let the engine idle.
Page 324: Cooling System
Cooling System When you decide it is safe to lift the hood, here is what you will see: 3.8L V6 Engine A. Coolant Recovery Tank B. Radiator Pressure Cap C. Electric Engine Cooling Fans 5-30 3.6L V6 Engine A. Coolant Recovery Tank B.
Page 325 If the coolant inside the coolant recovery tank is boiling, do not do anything else until it cools down. The vehicle should be parked on a level surface. When the engine is cold, the coolant level should be at or above the cold ﬁll line on the coolant recovery tank. If it is not, there may be a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump, or somewhere else in the cooling system.
Page 326 How to Add Coolant to the Coolant Recovery Tank CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture.
Page 327: How To Add Coolant To The Radiator
If the overheat warning continues, there is one more thing you can try. You can add the proper coolant mixture directly to the radiator, but be sure the system is cool before you do it. CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly.
Page 328 3. Open the coolant air bleed valve located on the thermostat housing near the heater hose. See Engine Compartment Overview on page 5-12 for more information on location. 5-34 4. Fill the radiator with the proper DEX-COOL coolant mixture, up to the base of the ﬁller neck.
Page 329 8. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. 9. By this time, the coolant level inside the radiator ﬁller neck may be lower. If the level is lower, add more of the proper DEX-COOL through the ﬁller neck until the level reaches the base of the ﬁller neck.
Page 330 How to Add Coolant to the Cooling System (3.6L V6 Engine) Notice: Your engine has a speciﬁc cooling system drain and ﬁll procedure. Failure to follow this procedure could cause your engine to overheat and be severely damaged. If your engine’s cooling system needs to be drained and re-ﬁlled, please see your dealer.
Page 331: Power Steering Fluid
5. Then ﬁll the coolant recovery tank to the cold ﬁll line. 6. Reinstall the coolant recovery tank cap and the pressure cap. 7. If the coolant in the recovery tank is constantly low, you should have your dealership service department inspect the vehicle for leaks.
Page 332: Windshield Washer Fluid
How to Check Power Steering Fluid To check the power steering ﬂuid, do the following: 1. Turn the key off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag.
Page 333: Brakes
Open the cap with the washer symbol on it. Add washer ﬂuid until the tank is full. See Engine Compartment Overview on page 5-12 for reservoir location. Notice: • When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water.
Page 334: What To Add
So, it is not a good idea to top off your brake ﬂuid. Adding brake ﬂuid will not correct a leak. If you add ﬂuid when your linings are worn, then you will have too much ﬂuid when you get new brake linings. You should add or remove brake ﬂuid, as necessary, only when work is done on the brake hydraulic system.
Page 335: Brake Wear
Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving, except when you are pushing on the brake pedal ﬁrmly.
Page 336: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts. When you replace parts of your braking system —...
Page 337 CAUTION: Batteries can hurt you. They can be dangerous because: • They contain acid that can burn you. • They contain gas that can explode or ignite. • They contain enough electricity to burn you. If you do not follow these steps exactly, some or all of these things can hurt you.
Page 338 4. Open the hood on the other vehicle and locate the positive (+) and negative ( ) terminal locations on that vehicle. You will not use your vehicle’s battery for jump starting. It has a remote positive (+) jump starting terminal, located on the underhood fuse block, for that purpose.
Page 339 CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle.
Page 340 3.8L V6 Engine shown, 3.6L V6 Engine similar 6. Connect the red positive (+) cable to the positive (+) terminal location on the vehicle with the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal location on the vehicle with the good battery.
Page 341 Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Page 342: Headlamp Aiming
Headlamp Aiming The vehicle has a visual optical headlamp aiming system. The aim has been preset at the factory and should need no further adjustment However, If the vehicle is damaged in an accident, the headlamp aim may be affected and adjustment may be necessary.
Page 343 The vertical headlamp aiming screws are located under the hood near the headlamps. The adjustment screw can be turned with a 6 mm male hex. To adjust the vertical aim on the headlamps, do the following: 1. Find the aim dot on the lens of the low-beam lamp. 2.
Page 344 3. At the wall or other ﬂat surface, measure from the ground upward the recorded distance from Step 2 and draw or tape a horizontal line the width of the vehicle. 4. Turn on the low-beam headlamps and place a piece of cardboard or equivalent in front of the headlamp not being aimed.
Page 345: Bulb Replacement
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-56. For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 346 Low-Beam Headlamp and Sidemarker Bulbs To replace a low-beam headlamp or sidemarker bulb, do the following: 1. Open the hood. See Hood Release on page 5-11 for more information. 2. Remove the fastener from the front fascia. The fastener is located inboard of the headlamp assembly, near the high-beam headlamp.
Page 347: Front Turn Signal And Parking Lamps
6. Pull back on the front fascia and then pull the headlamp assembly out from the vehicle. Moving the headlamp up and down slightly may help with its removal. You may have someone assist you with this step. 7. Remove the access cover from behind the bulb being replaced.
Page 348: Taillamps, Turn Signal, Sidemarker
Taillamps, Turn Signal, Sidemarker, Stoplamps and Back-up Lamps To replace a taillamp, turn signal, sidemarker, stoplamp or back-up lamp bulb, do the following: 1. Open the trunk. See Trunk on page 2-13 for more information. 2. Remove the convenience net if the vehicle has one. 5-54 3.
Page 349 5. Remove the two wing nuts holding the taillamp assembly in place. 6. Pull out the taillamp assembly and disconnect the wiring harness. A. Taillamp D. Stoplamp/Taillamp/ B. Back-up C. Taillamp E. Sidemarker 7. Turn the bulb socket counterclockwise to remove it. 8.
Page 350: Windshield Replacement
Replacement Bulbs Exterior Lamps Back-Up Lamps Fog Lamp Front Turn Signal and Parking Lamps Headlamps High-Beam Low-Beam Front/Rear Sidemarker and Taillamp Stoplamps and Taillamps For replacement bulbs not listed here, contact your dealer. 5-56 Windshield Replacement Bulb Number Your vehicle is equipped with an acoustic windshield. If you ever have to have your windshield replaced be sure to get an acoustic windshield so you will continue to have the beneﬁts an acoustic windshield...
Page 351: Tires
2. While holding the wiper arm, pull the clip up from the blade connecting point, and pull the blade assembly down toward the windshield to remove it from the wiper arm. 3. Install the new wiper blade onto the wiper arm and snap the clip into place.
Page 352: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P-Metric) Tire Example (A) Tire Size: The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 353 Compact Spare Tire Example (A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone ﬂat.
Page 354: Tire Terminology And Deﬁnitions
Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter P as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.S.
Page 355 Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles less than 90 degrees to the centerline of the tread.
Page 356 Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of an asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering, or bears manufacturer, brand, and/or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire.
Page 357: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure Tires need the correct amount of air pressure to operate effectively. Notice: Do not let anyone tell you that under-inﬂation or over-inﬂation is all right. It is not. If your tires do not have enough air (under-inﬂation), you can get the following: •...
Page 358: Tire Inspection And Rotation
How to Check Use a good quality pocket-type gage to check tire pressure. You cannot tell if your tires are properly inﬂated simply by looking at them. Radial tires may look properly inﬂated even when they are under-inﬂated. Check the tire’s inﬂation pressure when the tires are cold.
Page 359 When rotating your tires, always use the correct rotation pattern shown here. Do not include the compact spare tire in your tire rotation. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Tire and Loading Information label.
Page 360: When It Is Time For New Tires
When It Is Time for New Tires One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. You need a new tire if any of the following statements are true: •...
Page 361 CAUTION: Mixing tires could cause you to lose control while driving. If you mix tires of different sizes, brands, or types (radial and bias-belted tires), the vehicle may not handle properly, and you could have a crash. Using tires of different sizes, brands, or types may also cause damage to your vehicle.
Page 362: Different Size Tires And Wheels
Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability and resistance to rollover. Additionally, if your vehicle has electronic systems such as, antilock brakes;...
Page 363 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Page 364: Wheel Alignment And Tire Balance
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, if you notice unusual tire wear or your vehicle pulling to one side or the other, the alignment may need to be checked.
Page 365: Used Replacement Wheels
CAUTION: Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured.
Page 366: Tire Chains
Tire Chains CAUTION: If your vehicle has P225/55R17 size tires, do not use tire chains, there is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts.
Page 367: Changing A Flat Tire
Get the vehicle under control by steering the way you want the vehicle to go. It may be very bumpy and noisy, but you can still steer. Gently brake to a stop, well off the road if possible. CAUTION: Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training.
Page 368: Removing The Spare Tire And Tools
When your vehicle has a ﬂat tire, use the following example as a guide to assist you in the placement of wheel blocks. The following information will tell you next how to use the jack and change a tire. 5-74 Removing the Spare Tire and Tools The equipment you will need is located in the trunk.
Page 369 4. Turn the wing nut counterclockwise and remove it. 6. Turn the nut holding the jack counterclockwise and remove it. Then remove the jack and wrench. 5. Remove the compact spare tire. 5-75...
Page 370: Removing The Flat Tire And Installing The Spare Tire
The tools you will need to change a tire include the jack (A), extension and protection guide (B), and wheel wrench (C). 5-76 Removing the Flat Tire and Installing the Spare Tire If the vehicle has steel wheel covers with center caps, the wheel nuts are hidden behind the cap.
Page 371 2. Use the wheel wrench to loosen the plastic wheel nut caps, if equipped, in a counterclockwise direction. If needed, ﬁnish loosening them by hand. The nut caps will not come off of the wheel cover. 3. Use the ﬂat end of the wheel wrench and pry along the edge of the cover until it comes off.
Page 372 3. Find the jacking location using the diagram above and corresponding hoisting notches located on the underside of the vehicle’s plastic molding. The notches in the plastic molding are marked with a triangle shape to help you ﬁnd them. The front location is about 6.5 inches (16.5 cm) from the rear edge of the front wheel well.
Page 373 5. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground for the compact spare tire to ﬁt under the vehicle. 6. Remove all wheel nuts and take off the ﬂat tire. 5-79...
Page 374 CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident. When you change a wheel, remove any rust or dirt from the places where the wheel attaches to the vehicle.
Page 375 CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to come loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts. If you have to replace them, be sure to get new GM original equipment wheel nuts.
Page 376: Storing A Flat Or Spare Tire And Tools
Storing a Flat or Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. After the compact spare tire has been installed on the vehicle, store the ﬂat tire in the trunk.
Page 377: Compact Spare Tire
Compact Spare Tire A. Cover B. Wing Nut Although the compact spare tire was fully inﬂated C. Compact Spare Tire when the vehicle was new, it can lose air after a time. D. Wing Nut Check the inﬂation pressure regularly. It should be 60 psi (420 kPa).
Page 378: Appearance Care
Appearance Care Cleaning the Inside of Your Vehicle Your vehicle’s interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on your upholstery. Dirt can damage carpet, fabric, leather, and plastic surfaces.
Page 379: Fabric/Carpet
Your GM dealer has a product for cleaning your vehicle’s glass. Should it become necessary, you can also obtain a product from your GM dealer to remove odors from your vehicle’s upholstery. Do not clean your vehicle using the following cleaners or techniques: •...
Page 380: Leather
If any of the soil remains, a commercial fabric cleaner or spot lifter may be necessary. When a commercial upholstery cleaner or spot lifter is to be used, test a small hidden area for colorfastness ﬁrst. If the locally cleaned area gives any impression that a ring formation may result, clean the entire surface.
Page 381: Care Of Safety Belts
Care of Safety Belts Keep belts clean and dry. CAUTION: Do not bleach or dye safety belts. If you do, it may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water.
Page 382: Finish Care
Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint ﬁnish. GM-approved cleaning products can be obtained from your dealer. See Vehicle Care/ Appearance Materials on page 5-91. Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint ﬁnish may damage it.
Page 383: Aluminum Or Chrome-Plated Wheels
Aluminum or Chrome-Plated Wheels The vehicle may be equipped with either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.
Page 384: Sheet Metal Damage
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the warranty. Finish Damage Any stone chips, fractures or deep scratches in the ﬁnish should be repaired right away.
Page 385: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Oil Removes tar, road oil, Remover and asphalt. Chrome Cleaner Use on chrome or and Polish stainless steel. White Sidewall Removes soil and black Tire Cleaner marks from whitewalls.
Page 386: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle. The VIN also appears on the Vehicle Certiﬁcation and Service Parts labels and the certiﬁcates of title and registration.
Page 387: Electrical System
Electrical System Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer ﬁrst. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 388: Instrument Panel Fuse Block
Instrument Panel Fuse Block The instrument panel fuse block is located on the passenger’s side of the instrument panel. Pull off the cover labeled FUSES to expose the fuse block. 5-94 Fuses Usage DR/LCK Door Locks, Trunk TRUNK RFA/MOD Remote Keyless Entry PRK/SWTCH Ignition Key Lock CLSTR...
Page 389: Underhood Fuse Block
Fuses Usage INT/ILLUM Interior Lamps PWR/SEAT Power Seat S/ROOF Sunroof CNSTR Canister Vent HVAC Climate Control System HAZRD Turn Signal, Hazard PRK/LAMP Park Lamps Center-High-Mounted CHMSL/BKUP Stoplamp/Back-up Lamps PWR/MIR Power Mirrors CRUISE Cruise Control RDO/AMP Radio, Ampliﬁer HTD/SEAT Heated Seats HTD/MIR Heated Mirrors PWR/WNDW...
Page 390 Mini-Fuses Windshield Wiper Washer/Regulated Voltage Control Fog Lamps Transaxle Control Module Supplemental Inﬂatable Restraint Auxiliary Power Horn Emission Air Conditioner Clutch Oxygen Sensor Powertrain Control Module Powertrain Control Module, Electronic Throttle Control Electronic Throttle Control Display Anti-lock Brake Solenoid Fuel Injector 5-96 Usage Mini-Fuses...
Page 391 Micro-Relays Usage Headlamp High Beam HDM Module Fog Lamp Ignition 1 Air Conditioning Compressor Horn Powertrain Fuel Pump Mini-Relays Usage Fan 1 Fan 3 Windshield Wiper High Windshield Wiper Fan 2 Crank Spare Fuses Usage Spare Spare Spare Spare Spare Spare Fuse Puller Usage...
Page 392: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. Application Automatic Transaxle Cooling System Including Reservoir 3.6L V6 3.8L V6 Engine Oil with Filter 3.6L V6 3.8L V6 Fuel Tank Wheel Nut Torque All capacities are approximate. When adding, be sure to ﬁll to the approximate level, as recommended in this manual.
Page 393: Maintenance Schedule
Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-3 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-8 At Each Fuel Fill ...6-9 At Least Once a Month ...6-9 At Least Once a Year ...6-10 Recommended Fluids and Lubricants ...6-12...
Page 394: Introduction
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and...
Page 395: Using The Maintenance Schedule
Using the Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather.
Page 396: Scheduled Maintenance
Owner Checks and Services on page 6-8 tells you what should be checked, when to check it, and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, ﬂuids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-12 and Normal Maintenance Replacement Parts on page 6-13.
Page 397 Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and ﬁlter. See Engine Oil on page 5-15. Reset oil life system. See Engine Oil Life System on page 5-18. An Emission Control Service. Visually check for any leaks or damage. See footnote (k). Inspect engine air cleaner ﬁlter.
Page 398: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 399: Maintenance Footnotes
Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chaﬁng, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect other brake parts, including calipers, parking brake, etc. (b) Visually inspect front and rear suspension and steering system for damaged, loose, or missing parts or signs of wear.
Page 400: Owner Checks And Services
(h) Change automatic transaxle ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. −...
Page 401: At Each Fuel Fill
At Each Fuel Fill It is important to perform these underhood checks at each fuel ﬁll. Engine Oil Level Check Check the engine oil level and add the proper oil if necessary. See Engine Oil on page 5-15 for further details.
Page 402: At Least Once A Year
At Least Once a Year Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle.
Page 403: Ignition Transaxle Lock Check
Ignition Transaxle Lock Check While parked, and with the parking brake set, try to turn the ignition to OFF in each shift lever position. • The ignition should turn to OFF only when the shift lever is in PARK (P). •...
Page 404: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation may be obtained from your dealer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certiﬁed for Gasoline Engines starburst symbol.
Page 405: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your GM dealer. Normal Maintenance Replacement Parts Part Engine Air Cleaner/Filter Engine Oil Filter 3.6L V6 3.8L V6 Passenger Compartment Air Filter Spark Plugs 3.6L V6 Engine 3.8L V6 Engine...
Page 406: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. You should retain all maintenance receipts.
Page 407 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-15...
Page 408 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-16...
Page 409: Customer Assistance And Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-4 Customer Assistance for Text Telephone (TTY) Users ...7-4 Customer Assistance Offices ...7-4 GM Mobility Reimbursement Program ...7-6 Roadside Assistance Program ...7-6 Courtesy Transportation ...7-8 Vehicle Data Collection and Event Data Recorders ...7-10 Collision Damage Repair ...7-11 Customer Assistance and Information...
Page 410: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Buick. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your GM dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 411 STEP THREE: Both General Motors and your dealer are committed to making sure you are completely satisﬁed with your new vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, you should ﬁle with the BBB Auto Line Program to enforce any additional rights you may have.
Page 412: Online Owner Center
Customer Assistance Offices Buick encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Buick, refer to the addresses below. United States — Customer Assistance Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-5136 www.Buick.com...
Page 413 From Puerto Rico: 1-800-496-9992 (English) 1-800-496-9993 (Spanish) Fax Number: 313-381-0022 From U.S. Virgin Islands 1-800-496-9994 Fax Number: 313-381-0022 Canada — Customer Assistance General Motors of Canada Limited Customer Communication Centre, 163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For Text Telephone devices (TTYs)) Roadside Assistance: 1-800-268-6800...
Page 414: Gm Mobility Reimbursement Program
Assistance program. This value-added service is intended to provide you with peace of mind as you drive in the city or travel the open road. Call Buick’s Roadside Assistance toll-free number at 1-800-252-1112 to speak with a Buick Roadside Assistance representative 24 hours a day, 365 days a year.
Page 415: Canadian Roadside Assistance
Buick Roadside Assistance: 1-800-252-1112, text telephone (TTY) users, call 1-888-889-2438. Buick reserves the right to limit services or reimbursement to an owner or driver when, in Buick’s judgement, the claims become excessive in frequency or type of occurrence.
Page 416: Courtesy Transportation
Courtesy Transportation To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for new vehicles. The Courtesy Transportation program is offered to customers in conjunction with the Bumper-to-Bumper coverage provided by the New Vehicle Limited Warranty. Several transportation options are available when warranty repairs are required.
Page 417: Additional Program Information
Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for a warranty repair. Reimbursement will be limited to a maximum amount per day and must be supported by receipts.
Page 418: Vehicle Data Collection And Event Data Recorders
Vehicle Data Collection and Event Data Recorders Your vehicle, like other modern motor vehicles, has a number of sophisticated computer systems that monitor and control several aspects of the vehicle’s performance. Your vehicle uses on-board vehicle computers to monitor emission control components to optimize fuel economy, to monitor conditions for airbag deployment and, if so equipped, to provide anti-lock braking and to help the driver control the vehicle in difficult driving situations.
Page 419: Collision Damage Repair
Others, such as law enforcement, may have access to the special equipment that can read the information if they have access to the vehicle or the device that stores the data. If your vehicle is equipped with OnStar ® check the OnStar subscription service agreement or manual for information on its operations and data collection.
Page 420 Repair Facility GM also recommends that you choose a collision repair facility that meets your needs before you ever need collision repairs. Your GM dealer may have a collision repair center with GM-trained technicians and state of the art equipment, or be able to recommend a collision repair center that has GM-trained technicians and comparable equipment.
Page 421 • If you need roadside assistance, call GM Roadside Assistance. See Roadside Assistance Program on page 7-6 for more information. • If your vehicle cannot be driven, know where the towing service will be taking it. Get a card from the tow truck operator or write down the driver’s name, the service’s name, and the phone number.
Page 422: Reporting Safety Defects
Managing the Vehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair. If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there. Specify to the facility that any required replacement collision parts be original equipment parts, either new Genuine GM parts or recycled original GM parts.
Page 423: Reporting Safety Defects To The Canadian Government
In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you will notify us. Please call us at 1-800-521-7300, or write: Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-5136 In Canada, please call us at 1-800-263-3777 (English) or 1-800-263-7854 (French).
Page 424: Service Bulletins
Service Bulletins Service Bulletins give technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. In Canada, information pertaining to Product Service Bulletins can be obtained by contacting your General Motors dealer or by calling 1-800-GM-DRIVE (1-800-463-7483).
Page 425 Accessories and Modiﬁcations ... 5-3 Accessory Power Outlet(s) ... 3-20 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-66 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-93 Air Cleaner/Filter, Engine ... 5-20 Air Conditioning ... 3-22, 3-25 Airbag Passenger Status Indicator ... 3-35 Readiness Light ...
Page 426 Audio System(s) (cont.) Setting the Time ... 3-83 Theft-Deterrent Feature ... 3-124 Understanding Radio Reception ... 3-126 XM™ Satellite Radio Antenna System ... 3-128 Automatic Door Lock ... 2-12 Automatic Transaxle Fluid ... 5-21 Operation ... 2-26 Backglass Antenna ... 3-127 Battery ...
Page 427 Check Engine Light ... 3-41 Check Gas Cap Light ... 3-48 Checking Things Under the Hood ... 5-10 Chemical Paint Spotting ... 5-90 Child Restraints Child Restraint Systems ... 1-34 Infants and Young Children ... 1-31 Lower Anchors and Tethers for Children ... 1-39 Older Children ...
Page 428 Cooling System ... 5-30 Courtesy Lamps ... 3-16 Cruise Control ... 3-10 Cruise Control Light ... 3-45 Cupholder(s) ... 2-45 Customer Assistance Information Courtesy Transportation ... 7-8 Customer Assistance for Text Telephone (TTY) Users ... 7-4 Customer Assistance Offices ... 7-4 Customer Satisfaction Procedure ...
Page 429 Electrical System Add-On Equipment ... 5-93 Fuses and Circuit Breakers ... 5-93 Headlamp Wiring ... 5-93 Instrument Panel Fuse Block ... 5-94 Power Windows and Other Power Options ... 5-93 Underhood Fuse Block ... 5-95 Windshield Wiper Fuses ... 5-93 Engine Air Cleaner/Filter ...
Page 430 Fuel (cont.) Filling Your Tank ... 5-8 Fuels in Foreign Countries ... 5-7 Gage ... 3-48 Gasoline Octane ... 5-5 Gasoline Speciﬁcations ... 5-6 Low Warning Light ... 3-48 Fuses Fuses and Circuit Breakers ... 5-93 Instrument Panel Fuse Block ... 5-94 Underhood Fuse Block ...
Page 431 Hood Checking Things Under ... 5-10 Release ... 5-11 Horn ... 3-6 How to Use This Manual ... ii How to Wear Safety Belts Properly ... 1-14 Ignition Positions ... 2-23 Infants and Young Children, Restraints ... 1-31 Inﬂation -- Tire Pressure ... 5-63 Instrument Panel Overview ...
Page 432 Light (cont.) Change Engine Oil ... 3-45 Charging System ... 3-37 Check Gas Cap ... 3-48 Cruise Control ... 3-45 Door Ajar ... 3-47 Engine Coolant Temperature Warning ... 3-40 Headlamps Suggested ... 3-46 Highbeam On ... 3-46 Low Coolant Warning ... 3-41 Low Fuel Warning ...
Page 433 Maintenance Schedule Additional Required Services ... 6-6 At Each Fuel Fill ... 6-9 At Least Once a Month ... 6-9 At Least Once a Year ... 6-10 Introduction ... 6-2 Maintenance Footnotes ... 6-7 Maintenance Record ... 6-14 Maintenance Requirements ... 6-2 Normal Maintenance Replacement Parts ...
Page 434 Outside Convex Mirror ... 2-38 Power Heated Mirrors ... 2-38 Power Mirrors ... 2-37 Overhead Console Reading Lamps ... 3-18 Overheated Engine Protection Operating Mode ... 5-29 Owner Checks and Services ... 6-8 Owners, Canadian ... ii Park Aid ... 3-18 Park (P) Shifting Into ...
Page 435 Rear Assist Handle Reading Lamps ... 3-18 Rear Door Security Locks ... 2-12 Rear Safety Belt Comfort Guides ... 1-25 Rear Seat Passengers, Safety Belts ... 1-23 Rearview Mirror, Automatic Dimming ... 2-36 Rearview Mirror, Automatic Dimming ® with OnStar ...
Page 436 Seats Center Seat ... 1-7 Head Restraints ... 1-6 Heated Seats ... 1-4 Manual ... 1-2 Power Lumbar ... 1-3 Reclining Seatbacks ... 1-4 Six-Way Power Seats ... 1-3 Split Folding Rear Seat ... 1-7 Securing a Child Restraint Center Front Seat Position ... 1-48 Rear Seat Position ...
Page 437 Tachometer ... 3-33 Taillamps Turn Signal, Sidemarker, Stoplamps, and Back-Up Lamps ... 5-54 TCS Warning Light ... 3-39 Theater Dimming ... 3-17 Theft-Deterrent, Radio ... 3-124 Theft-Deterrent Systems ... 2-18 Content Theft-Deterrent ... 2-18 ® PASS-Key III ... 2-20 ® PASS-Key III Operation ...
Page 438 Vehicle Control ... 4-6 Damage Warnings ... iv Loading ... 4-31 Service Soon Light ... 3-47 Symbols ... iv Vehicle Data Collection and Event Data Recorders ... 7-10 Vehicle Identiﬁcation Number (VIN) ... 5-92 Service Parts Identiﬁcation Label ... 5-92 Vehicle Personalization DIC ...

This manual is also suitable for:

Allure 2006

Buick 2006 LaCrosse Owner's Manual

Section 1 Seats and Restraint Systems

Seats and Restraint Systems

Front Seats

Rear Seats

Safety Belts

Child Restraints

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Universal Home Remote System

Storage Areas

Sunroof

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Windshield Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Buick 2006 LaCrosse

Summary of Contents for Buick 2006 LaCrosse