Download Print this page
Holland TL4048 Series Installation Manual

Holland TL4048 Series Installation Manual

Liftgates

Advertisement

Quick Links

Installation Manual
TL4048/4052/4061 and TL5061 Series Liftgates
Mounting Brackets for Frameless Trailers
Introduction
This manual provides you with the information necessary
to properly install the trailer mounting brackets with the
SAF-HOLLAND TL Series Liftgate on frameless trailers.
NOTE: For liftgate components replacement, contact
SAF-HOLLAND Customer Service at:
U.S.
888-396-6501
Canada 800-503-9847
Warranty
Refer to the complete warranty for the country in which
the product will be used. A copy of the warranty certificate
is included with the product as well as on the SAF-HOLLAND
website (www.safholland.us and www.safholland.ca). It may
also be ordered directly from SAF-HOLLAND; the address is
shown on the back cover.
Notes, Cautions, and Warnings
You must read and understand all of the safety procedures
presented in this manual before operating or starting any
work on the liftgate.
NOTE: In the United States, workshop safety requirements
are defined by federal and/or state Occupational
Safety and Health Act. Equivalent laws may exist
in other countries. This manual is written based
on the assumption that OSHA or other applicable
employee safety regulations are followed by the
location where work is performed.
Proper tools must be used to perform the procedures
described in this manual. Many of these procedures may
require special tools.
IMPORTANT: Read this manual before using this
product. Keep this manual in a safe
location for future reference.
Failure to follow the instructions and
safety precautions in this manual could
result in death or serious injury.
XL-TG10157BM-en-US Rev A · 2013-01-03 · Amendments and errors reserved · © SAF-HOLLAND, Inc.
Throughout this manual, you will notice the terms "NOTE,"
"IMPORTANT," "CAUTION," and "WARNING" followed
by useful product information. So that you may better
understand the manual, those terms are as follows:
NOTE: Includes additional information to enable accurate
and easy performance of procedures.
IMPORTANT: Includes additional information that if
not followed could lead to hindered
product performance.
Used without the safety alert symbol,
indicates a potentially hazardous situation
which, if not avoided, could result in
property damage.
Indicates a potentially hazardous situation
which, if not avoided, could result in minor
or moderate injury.
Indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.

Advertisement

loading

Summary of Contents for Holland TL4048 Series

  • Page 1 Keep this manual in a safe location for future reference. Failure to follow the instructions and safety precautions in this manual could result in death or serious injury. XL-TG10157BM-en-US Rev A · 2013-01-03 · Amendments and errors reserved · © SAF-HOLLAND, Inc.
  • Page 2 Failure to follow proper weld procedures could cause failure or fracture which, if not avoided, could result in death or serious injury. XL-TG10157BM-en-US Rev A · 2013-01-03 · Amendments and errors reserved · © SAF-HOLLAND, Inc.
  • Page 3 12" 14" (FOR 61" PLATFORMS) 8" 5.38" 21" (FOR 48" AND 52" PLATFORM) 26" (FOR 61" PLATFORM) Figure 5 CROSSMEMBER SLIDE RAIL FLUSH FLUSH MOUNTING BRACKET XL-TG10157BM-en-US Rev A · 2013-01-03 · Amendments and errors reserved · © SAF-HOLLAND, Inc.
  • Page 4 MOUNTING BRACKET TOP FACE OF CROSSMEMBER SLIDE RAIL 1/4" SAF-HOLLAND USA, Inc. · 888.396.6501 · Fax 800.356.3929 SAF-HOLLAND Canada Limited · 519.537.3494 · Fax 800.565.7753 Western Canada · 604.574.7491 · Fax 604.574.0244 SAF-HOLLAND Mexico · 52.55.5362.8743 · Fax 52.55.5362.8743 www.safholland.us...

This manual is also suitable for:

Tl4052 seriesTl4061 seriesTl5061 series