Dukane SunSplash SP2123A Operator's Manual

2000/2200 Lumen Model SP2123A/2223A
– Important! –
Immediately Check for Loose Lamps
Open top stage by pressing the release tab located on
the mast side of the stage. Check to see that the lamps
are fully inserted into the socket and correctly aligned.
Never touch the lamp with your bare skin. Do not get
skin oil on the bulb. Hold lamp with tissue, paper, cloth
or other clean object.

Electrical Safety Grounding Instructions

This Class I product uses a three-wire power cord that
grounds the product for your protection. Do not DEFEAT
or REMOVE the grounding pin. If an extension cord is
used, it must also be a three-wire type with an ampere
rating equal or greater than the product's rating. The plug
must be connected to a properly grounded three-terminal
power receptacle. Connection to any other type of recep-
tacle should be done only by a qualified electrician in
accordance with local and/or national electrical codes.
Operation
The projector features a folding mast. The mast can be
lowered by pulling the release knob located at the bottom
pivot assembly.
The power switch is located on the front of the unit.
The stage can be opened by pressing the release tab
located on the mast side of the stage.
Be sure vent area are not blocked.
There is a thermal switch to prevent overheating.
The lamp changer is operated by rotating the knob on the
front of the unit.
To prevent damage to good lamps, only use the changer
after lamps have cooled.
Cleaning
Use a soft, lint-free cloth to remove dust from stage glass
and projection lens. Lens cleaner may be used on these
components.
For mirrors, use a soft brush to remove dirt.

Lamp Replacement

2000/2200 lumen projectors use a 360 Watt EYB lamp,
Dukane part number 456-186. WARNING! Lamp and
adjacent parts are HOT. Allow the lamp to cool. The lamp
glass envelope may shatter. Avoid placing near eyes. Hold
lamp with cloth, tissue or gloved hand. Do not get skin oil
on the bulb.
2900 Dukane Drive • St. Charles, Illinois 60174 • Toll-free: 800-676-2485 • Fax: 630-584-5156
avsales@dukcorp.com • www.dukcorp.com/av
Sunspalsh Overhead Projector
Operator's Manual
IMPORTANT SAFETY INSTRUCTIONS
When using your overhead projector, basic safety precau-
tions should always be followed, including the following:
1. Read and understand all instructions before using.
2. Close supervision is necessary when any projector is
used by or near children. Do not leave projector
unattended while in use.
3. Care must be taken as burns can occur from touch-
ing hot parts.
4. Do not operate projector with a damaged cord or if
the projector has been dropped or damaged — until it
has been examined by a qualified service technician.
5. Position the cord so that it will not be tripped over, be
pulled or contact hot surfaces.
6. If an extension cord is necessary, a cord with a
current rating at least equal to that of the projector
should be used. Cords rated for less amperage than
the projector may overheat.
7. Always unplug projector from electrical outlet before
cleaning and servicing and when not in use. Never
yank cord to pull plug from outlet. Grasp plug and pull
to disconnect.
8. Let projector cool completely before putting away.
9. To protect against the risk of electric shock, do not
immerse this projector in water or other liquids.
10. To avoid the risk of electric shock, do not disas-
semble this projector, but take it to a qualified service
technician when some service or repair work is
required. Incorrect reassembly can cause electric
shock when the projector is used subsequently.
11. The use of an accessory attachment not recom-
mended by
the manufacturer may cause a risk of fire, electric
shock or injury to persons.
12. Connect this projector to a grounded outlet.
13. Disconnect this unit from its source of supply before
replacing the projection lamp.
Additional lamp safeguards: never handle lamps with bare
fingers; periodically inspect lamps, when they're turned off,
for signs of blistering or blackening; insure proper action of
the cooling system; turn off the projector immediately if the
image becomes abnormally dim; never operate a projector
with the lamp housing open; and make sure that the lamp
itself is properly seated.
SAVE THESE INSTRUCTIONS
Audio Visual Products
401-2123A-02