Sony STR-DA9000ES Operating Instructions Manual page 41

Hi-fi receivers: fm stereo/fm-am receiver
Hide thumbs Also See for STR-DA9000ES:
Table of Contents

Advertisement

x i POWER (i.LINK power management)
• AUTO
Lets you turn off the power of the unnecessary
i.LINK circuits automatically. You can enjoy high
quality digital or analog audio without the influence
of the i.LINK circuits. When set to "AUTO", it takes
some time to output the sound. See page 25 for a note
on switching the input when set to "AUTO".
• EVER ON
Lets you keep the power of the i.LINK circuits.
Select if you do not like the time lag that occurs with
the "AUTO" setting.
x H.A.T.S. (H.A.T.S. (High quality digital Audio
Transmission System) function)
• ON
The digital audio signals input from the i.LINK
component is stored in the buffer temporarily, then
retrieved from the buffer and converted to analog
audio signals at the proper timing. The sound quality
is enhanced because there is no jitter (timing gaps
when reading signals) when transmitting the digital
audio signals. If you do not want to use this function,
select "OFF".
• OFF
This function is not activated.
Note
It takes some time to output the sound after the
playback operation is performed on the connected
component (ex., press PLAY button, press STOP
button, press PAUSE button) due to limitations of the
H.A.T.S. system. The time lag depends on the sound
source.
x DSD-SW SWAP (DTS-SW swapping)
On some multi channel Super Audio CDs, the 6th
channel is not for the sub woofer, but contains some
other sound (such as reverberation from the ceiling,
etc.).
This item lets you switch the output of the 6th channel
signals from the SUB WOOFER PRE OUT to the
SURROUND BACK terminals.
• ON
6th channel DSD signals input through the i.LINK
connection and SUB WOOFER channel signals
input through the MULTI CHANNEL IN 1 or
MULTI CHANNEL IN 2 terminals are output from
the SURROUND BACK terminals, and no sound is
output from the SUB WOOFER PRE OUT.
• OFF
Sound is output from the SUB WOOFER PRE OUT
as normal.
Note
This function does not work when "SURR BACK SP"
in the SPEAKER SET UP menu is set to "NO"
(page 22).
x LIP SYNC (Time alignment)
Initial setting: 0 ms
Lets you delay the output of audio to adjust the gap
between video and audio. You can adjust from 0 ms to
200 ms in 10 ms steps.
This function is not available in the following cases:
– When analog input is selected and DIRECT function
is used.
– When MULTI CH IN 1/2 is selected.
– When DSD signal is input from the i.LINK
component.
x DC PHASE L. (DC Phase Linearlizer)
Lets you approximate the low frequency phase
characteristics to a traditional analog amplifier.
• OFF
Phase correction is not performed.
• LOW-A, STD-A, HIGH-A, LOW-B, STD-B,
HIGH-B
The bandwidth range of the phase correction
increases in the order of "LOW", "STD", "HIGH".
"B" parameter phase correction provides more
enhanced bass characteristics.
x MIX SCALING (Downmix scaling)
Lets you adjust the downmix scaling processing for
center and sub woofer channels. This parameter can be
set only when the center speaker is set to "MIX".
• ON
The downmix scaling is performed.
• OFF
The downmix scaling is not performed so that the
sound quality is not deteriorated. If the sound is heard
like a noise at the high input level, set to "ON".
x S.FIELD LINK (Sound field link)
• ON
Lets you apply the last selected sound field to an
input whenever it is selected. For example, if you
select STADIUM for the CD/SACD input, then
change to a different input and return to CD/SACD,
STADIUM will automatically be applied again.
• OFF
Sound field link is not activated.
x DEC. PRIORITY
(Digital audio input decoding priority)
Lets you specify the input mode for the digital signal
input to the DIGITAL IN jacks.
The initial setting is "AUTO" for VIDEO 1, VIDEO 2,
VIDEO 3, VIDEO 4, VIDEO 5, LD, TV/SAT, TAPE,
continued
US
41

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents