Sign in today to find solutions:

Don't have an account? Sign up

Crown Audio XLS 602 Specifications

Crown xls 602: specifications.

 
XLS 602
T
he XLS Series of power amplifiers from
Crown represents a new era in affordable,
quality power amplification. The line con-
sists of three models in a uniform, rugged
chassis, incorporating the best of tried-and-
true design principles and innovative features.
XLS Series amplifiers are professional stereo
power amplifiers engineered to meet demand-
ing audio requirements—reliably and within
budget. Plus, every XLS Series amplifier is
backed by Crown's unequaled Three-Year, No-
Fault, Fully-Transferrable Warranty that covers
everything.
With over five decades of experience designing
and building rock-solid products, Crown is the
standard in amp technology. So check out the
affordable, Crown XLS Series. They are a pow-
erful argument for quality and value!
For more details about the XLS Series,
contact the Crown Technical Support Group at
800-342-6939 or 219-294-8200. Also, visit the
Crown Audio website at www.crownaudio.com.
Specifications
The following applies to units in Stereo mode with 8-ohm loads
and rated input sensitivity unless otherwise specified.
Performance
Sensitivity (volts RMS) for full rated power at
4 ohms: 1.26.
Frequency Response (at 1 watt) 20 Hz to 20
kHz: ±0.75 dB.
Phase Response (degrees at 1 watt)
at 10 Hz: –10.
at 20 kHz: +19.
Signal-to-Noise Ratio (20 Hz to 20 kHz)
A-weighted, below rated power: > 100 dB.
No weighting, below rated power: > 97 dB.
Total Harmonic Distortion (THD) at full band-
width power, from 20 Hz to 1 kHz: < 0.15%.
Intermodulation Distortion (IMD): (60 Hz and
7 kHz at 4:1) from full rated output to –40 dB:
< 0.3%.
X L S
S E R I E S
Features
• Simple, reliable design incorporates many
popular features.
• Selectable high-pass filter on each channel
enables amplifier to work more efficiently
when full band-width is not required.
• Pair of linear optocoupler clip limiters pro-
tects loudspeakers from being overdriven.
• Housed in a rugged, all-steel 3U chassis.
• Efficient forced-air fan prevents excessive
thermal buildup.
Damping Factor (8 ohm) 10 Hz to 400 Hz: >200.
Crosstalk (below rated power)
at 1 kHz: –82 dB.
at 20 kHz: –58 dB.
Voltage Gain (at maximum output): 31 dB.
Power
Output Power:
Load Impedance: Safe with all types of loads.
Rated for 2 to 8 ohms in Stereo, 8 ohms in
Bridge-Mono.
AC Line Voltages Available (±10%): 120 and
230 VAC.
Line Frequency: 50/60 Hz.
• Electronically balanced XLR inputs and
touch-proof binding post outputs.
• Features precision detented level controls,
power switch, and four LEDs, which indi-
cate clip for each channel, power and fault
conditions.
• Three-Year, No-Fault, Fully-Transferrable
Warranty completely protects your invest-
ment and guarantees its specifications.
Controls
Level: Two front-panel, black rotary level
controls, one for each channel.
Power: Front-panel switch; on when in the UP
position.
Filter Switches: One per channel; three-posi-
tion back-panel switches set the frequency for
internal high-pass filters. Frequency setting is
30 Hz when switch is in left position; 15 Hz
when switch is centered; and bypassed when
switch is in right position.
Limiter Switch: Back-panel switch offers loud-
speaker protection against moderate amplifier
clip when set to the "IN" position.
Fuse: Provides overload protection.
Indicators
Clip: Two front-panel red LEDs, one for each
channel, illuminate when the channel's output
signal is being overdriven.
Power: Green front-panel LED indicates
amplifier has been turned on and AC power
is available.
Fault: Yellow front-panel LED illuminates when
amplifier is in protect mode. Also illuminates
briefly during normal power-up when amplifier
is first switched on.

Summary of Contents

  • Page 1

    With over five decades of experience designing and building rock-solid products, Crown is the standard in amp technology. So check out the affordable, Crown XLS Series. They are a pow- erful argument for quality and value! For more details about the XLS Series, contact the Crown Technical Support Group at 800-342-6939 or 219-294-8200.

  • Page 2

    With this unprecedented No-Fault protection, your new Crown amplifier is warranted to meet or exceed original specifications for the first three years of ownership. During this time, if your amplifier fails, or does not perform to original specifications, it will be repaired or replaced at our expense.

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: