Advertisement
Advertisement
Table of Contents
Related Manuals for Crate Flexwave FW120H
Summary of Contents for Crate Flexwave FW120H
- Page 1 Three-Channel Guitar Amplifier with DSP and Channel Tracking Owner’s Manual...
-
Page 2: Table Of Contents
FlexWave120H Guitar Amplifier w/DSP and Channel Tracking TABLE OF CONTENTS Introduction ... 3 Channel Tracking ... 4 The Front Panel ... 5 The Rear Panel ... 6 The DSP Section ... 7 Using the Footswitch with the DSP ... 8 Suggested Settings ... -
Page 3: Introduction
(DSP) and Channel Tracking. This rug- ged amplifier combines outstanding features with serious clean and distorted sounds. Digital Reverb, Delay, and Modulation effects provide you with a wide variety of sounds. Crate’s unique Channel Tracking feature automatically stores your DSP settings for each channel to memory. -
Page 4: Channel Tracking
FlexWave120H Guitar Amplifier w/DSP and Channel Tracking Channel Tracking Your Crate FlexWave120H gives you the power of Channel Tracking. Once you select a DSP setting for each channel, Channel Tracking stores the settings to memory whenever you change channels. When you go back to that channel, Channel Tracking recalls those DSP set-... -
Page 5: The Front Panel
The signal at this jack is summed into a mono signal, which is sent to the internal power amp circuit. Use the output level con- trol for the signal source to adjust the signal for the proper mix with your guitar. -
Page 6: The Rear Panel
25. INSERT: Use this jack to connect an external signal processor to the amplifier. Use Crate’s STP201, STP202, or STP203 stereo- to-mono Y-cord or an adapter such as Crate’s YPP117 and two 1/4" mono signal cables to connect to the effect, as shown below. -
Page 7: The Dsp Section
FlexWave120H Guitar Amplifier w/DSP and Channel Tracking The DSP Section Signal Path MOD + DELAY + REVERB 4. DELAY: Use this control to select the type of digital delay effect. In its fully coun- terclockwise position, the signal will be “dry” (without delay). -
Page 8: Using The Footswitch With The Dsp
FlexWave120H Guitar Amplifier w/DSP and Channel Tracking Using the Footswitch with the DSP The Crate three-button footswitch supplied with the FlexWave120H allows access to an addi- tional DSP preset for each channel of the amplifier. When the footswitch is connected to the amplifier as shown below, the “original”... -
Page 9: Suggested Settings
REVERB HIGH EFFECTS CLEAN DESIRED Down ‘n Dirty: SLAP LONG MEDIUM FLANGER CHORUS PHASER DELAY REVERB HIGH EFFECTS CLEAN DESIRED Mean & Obscene: SLAP LONG MEDIUM FLANGER CHORUS PHASER DELAY REVERB HIGH EFFECTS CLEAN DESIRED CLEAN OVERDRIVE VOLUME LEVEL HIGH... -
Page 10: System Block Diagram
FlexWave120H Guitar Amplifier w/DSP and Channel Tracking System Block Diagram TUNER BUFFER INPUT VOLUME OVERDRIVE GAIN HIGH GAIN SHAPE GAIN PHASER FLANGER MEDIUM CHORUS SLAP INPUT CLEAN MID HIGH OVERDRIVE LEVEL HIGH OVERDRIVE/ HIGH GAIN HIGH GAIN LEVEL LONG REVERB DELAY CLEAN/ OVERDRIVE... - Page 11 LOUD Technologies Inc., 16220 Wood-Red Road NE, Woodinville, WA 98072 • Tel: 1-866-858-5832 Declaration Of Conformity LOUD Technologies Inc. 16220 Wood-Red Rd. NE Woodinville, WA 98072, USA FlexWave120H Crate Audio Amplifier 92/31/EEC, 93/68/EEC, & 73/23/EWG EN60065 EN55013, EN55020, EN55022, EN55103, EN61000-3-2, & EN61000-3-3...
-
Page 12: Technical Specifications
Crate continually develops new products, as well as improves existing ones. For this reason, the specifications and information in this manual are subject to change without notice. “Crate” is a registered trademark of LOUD Technologies Inc. All other brand names mentioned are trademarks or registered trademarks of their respective holders and are hereby acknowledged.