Page of 2
Download Bookmark Comment

Chamberlain KLIK1U User Manual

Chamberlain clicker klik1u remote controls: user guide.
Hide thumbs
   
CLICKER
®
MODEL KLIK1U
Universal Garage Door Opener Remote Control
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
Read instructions thoroughly BEFORE beginning.
• ALWAYS keep remote controls out of reach of children. NEVER permit children to
operate, or play with remote control transmitters.
Start with garage door closed. Identify garage door opener type -Smart/Learn
button or DIP Switch. Smart/Learn button or DIP Switches are located on motor
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and
unit or external receiver. Refer to owner's manual if necessary.
there are no obstructions to door travel.
STOP
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit
Clicker products are intended to be used only with garage door openers
anyone to cross path of moving gate or door.
manufactured after 1993 that utilize photo-eyes safety sensors. These are
always located on or near the bottom of the door track. If your garage door
does not have the sensors attached and working, the opener is not
compliant with current federal safety regulations and should be replaced.
DIP SWITCH
Proceed with instructions according to your type of garage door opener.
SMART/LEARN BUTTON
1
See Chart B to
determine # of times to
CHART A
1
CHART B
See Chart A to
press button and write
determine # of times to
in blank on step 5.
# of
Brand
Description
Year
# of
Brand
Type/Color of
Year
press button and write
times to
times to
Smart/Learn
in blank on step 5.
press
press
button
button
2
11
Chamberlain
®
*
9 Position
'90-'92
1
Linear
®
Mega-Code
'97-Current
12
Chamberlain
®
*
9 Position
2
Chamberlain
*
Orange/Red
'97-'03
®
2
Canada
'83-'89
3
Chamberlain
®
*
Purple
'95-'Current
13
Genie
®
12 Position
'85
4
Chamberlain
®
*
Green
'93-'96
14
Linear Multicode
10 Position
'76
®
5
Genie
®
15
Chamberlain
®
8 Position
'83-'89
Overhead Door
®
Intellicode
'95-'05
16
Stanley/Multicode
®
10 Position
'76
6
Genie
®
17
Genie
9 Position
'85
®
Overhead Door
®
Intellicode
'05 Current
18
Linear
®
7
Stanley
®
Secure Code
'98
Moore-O-Matic
®
8 Position
'76
9
Wayne Dalton
®
Rolling Code
'99
19
Chamberlain
®
*
7 Position
'83-'89
11
Chamberlain
®
*
9 Position
'90-'92
*NOTE: LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are compatible
3
with Chamberlain technology.
Motor
Unit
3
OR
SMART/LEARN BUTTON
DIP SWITCH
ON
Existing Remote
Clicker Remote
1
2
3
Match DIP switches. Turn
Press program button until
extra switches OFF.**
LED lights.
KG
KG
4
4
1
2
3
KG
KG
Motor Unit
Press program button
until LED lights.
Press and release the
smart/learn button.
5
5
NOTE: Your opener may
appear different and you
may have to remove the
light lens to access the
learn button.
Select a button to program.
Select a button to program.
Press button
times
Press button
times
ensuring LED stops
LED Indicator
ensuring LED stops
flashing after each press.
flashing after each press.
Code is accepted when
Button 1
Code is accepted when
Button 2
one of the following
door activates.
occurs:
Click
Program Button
OR
OR
DIP Switches
6
NOTE: If there are
problems programming to
button 1, program to
button 2.
Battery
Press program button.
6
Battery Cover
7
REMOTE CONTROL BATTERY
Press program button.
7
Programming complete.
To prevent possible SERIOUS INJURY or DEATH:
Press selected button to
• NEVER allow small children near batteries.
test. If unit does not work,
• If battery is swallowed, immediately notify doctor.
return to Step 3.
To reduce risk of fire, explosion or chemical burn:
NOTE:
Programming complete.
• Replace ONLY with 3V2032 coin batteries.
2 Position DIP
Press selected button to
Switch:
• Do NOT recharge, disassemble, heat above 100°C (212°F) or
ON
test. If unit does not work,
If programming fails reverse
incinerate.
return to Step 3.
DIP switches (OFF to ON and
ON to OFF).
Dispose of batteries properly. Replace ONLY with 3V2032
www.clickerproducts.com
**3 Position DIP Switch:
coin batteries.
For Chamberlain remotes DO NOT
1-800-442-1255
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
use the "0" position, use "+" or "-".
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.
If you already have a 3-button
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie
THERE ARE NO OTHER USER SERVICEABLE PARTS.
is a Trademark of Overhead Door Corporation. Overhead Door is a Trademark of Overhead
remote, DIP switch #1 must be set to
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following
Door Corporation. Linear is a Trademark of Linear Corporation. Master Mechanic is a
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
"-" if the large button is to open the door. It may be
Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark
interference received, including interference that may cause undesired operation.
of The Stanley Works. Wayne Dalton is a trademark of Wayne Dalton Corporation. Do It is
necessary to reprogram original remote controls.
a trademark of Do It Best Corporation.
© 2008, Clicker Corporation
114A3485C
All Rights Reserved

   Related Manuals for Chamberlain KLIK1U

   Summary of Contents for Chamberlain KLIK1U

  • Page 1

    Step 3. www.clickerproducts.com 1-800-442-1255 Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door Corporation. Overhead Door is a Trademark of Overhead Door Corporation. Linear is a Trademark of Linear Corporation. Master Mechanic is a Trademark of TruServ.

  • Page 2

    1-800-442-1255 Chamberlain, LiftMaster y Moore-O-Matic son marcas comerciales de Chamberlain Group. Genie es una marca comercial de Overhead Door Corporation. Overhead Door es una marca comercial de Overhead Door Corporation. Linear es una marca comercial de Linear Corporation. Stanley es una marca comercial de The Stanley Works.

Comments to this Manuals

Symbols: 0
Latest comments:
  • Max McLane Mar 29, 2015 09:58:
    How do I de- program or unlearn button 2 or all buttons as to start over
  • Sandy Feb 07, 2015 09:56:
    i am a senior and i need to talk to a live person! My clicker model is KLIK2U and i don't see ant informatio​n about this model. My problem i can't use my clicker to open my garage door
  • david Jan 22, 2015 04:11:
    My remote stopped working on both different garage doors so I replaced the battery. It still did not work and my remote led light never illuminate​d. Just to check that the new battery was charged, I swapped it with the other clicker KLIC1 remote (identical​). The new battery worked on the working remote. I then tested the battery removed from the working clicker with the non-workin​g clicker. No luck. Neither KLIC1's illuminate​d but one works and one doesn't. What should I try next. I thought I could reprogram the non-functi​oning clicker but without the LED light ever illuminati​ng, I cannot. One battery was brand new. The one works but does not illuminate​. The other doesn't work and doesn't illuminate​. Neither illuminate​s.
  • Cindi Aug 26, 2014 09:44:
    My remote worked when I left. When I returned it would not work. Tried several options buying new. Then found these instructio​ns and I am programmed again. Thank you.
  • Linus Jun 07, 2014 06:39:
    No customer service means no future sales from me.