Canon MultiPASS MP730 Setup Sheet
Canon multipass mp730: install guide
Hide thumbs
Also See for MultiPASS MP730:
- Quick reference manual (108 pages) ,
- Setup sheet (9 pages) ,
- Specifications (2 pages)
Table of Contents
Advertisement
Quick Links
READ THIS SHEET FIRST
READ THIS SHEET FIRST
Thank you for purchasing the Canon MultiPASS MP730.
To get your machine ready for use, please follow the instructions in this Set-Up Sheet
before referring to any other documentation.
IMPORTANT
Unpack the machine and its components.
Check that you have the following:
Machine
Paper output tray
Printhead
NOTE
• A printer cable is not included. You must purchase a USB cable (less than 16 # / 8 ft./5 m) to
connect your machine to a computer.
Set-Up Sheet
Set-Up Sheet
• DO NOT assemble the machine or connect the USB cable
before installing the software. You will be instructed when
to assemble and connect the cable.
Multi-purpose tray
Document tray
Power cord
Documentation
(Set-Up Sheet, Quick Reference Guide)
MultiPASS MP730/700 Setup CD-ROM
Telephone line cord
Destination labels
Tray cover
Ink tanks
(Black, cyan, magenta, yellow)
Advertisement
Table of Contents
Related Manuals for Canon MultiPASS MP730
Summary of Contents for Canon MultiPASS MP730
- Page 1 Set-Up Sheet READ THIS SHEET FIRST READ THIS SHEET FIRST Thank you for purchasing the Canon MultiPASS MP730. To get your machine ready for use, please follow the instructions in this Set-Up Sheet before referring to any other documentation. • DO NOT assemble the machine or connect the USB cable IMPORTANT before installing the software.
-
Page 2: Install The Software
Turn on your computer. On your computer, quit any open applications, including virus checkers. Insert the MultiPASS MP730/700 Setup CD-ROM into your disk drive. In the [MP Setup] screen, click [Install MP Drivers]. • If Set-up screen is not displayed, on the Windows desktop, double-click [My Computer] (Windows XP: Click [Start], then click [My Computer]). -
Page 3: Assemble The Machine
Follow the on-screen instructions. Click [Finish]. IMPORTANT • Proceed to step below to assemble the machine. Please keep your computer powered on. Remove the shipping material from the machine. Place the machine on a flat surface. Remove all shipping tapes from the exterior of the machine. Open the document cover Open the feeder cover C and remove the shipping material D as shown below. -
Page 4: Connect The Power Cord
Connect the telephone line and any necessary external device, and set the receive mode. You can connect an external device (telephone or answering machine) if necessary. Connect the telephone line cord to the wall jack. NOTE • Before using your machine, you need to make sure it is set for your telephone line type. -
Page 5: Load Paper
Load paper. Place a stack of paper (print-side up) in the multi-purpose tray guide A and adjust to the width of the stack w. Then place the tray cover D over the multi-purpose tray e. NOTE • You may have to move over the document cover cable E to place the tray cover on the multi-purpose tray. -
Page 6: Install The Ink Tanks
Raise the lock lever C, then gently slide the printhead into the holder. Lower the lock lever. IMPORTANT • Do not lift the lock lever once the printhead has been installed. Install the ink tanks. Start with the yellow ink tank. Pull the orange tape in the direction of the arrow and remove the plastic wrapper so you can see the air hole A. -
Page 7: Align The Printhead
Align the printhead. NOTE • You can also align the printhead from the software. For details, refer to the Software Guide. When the LCD A displays the following, press [Set]. A L I G N P R I N T H E A D P R E S S S E T K E Y The machine will print a horizontal pattern, and the LCD will display: C H A N G E H V A L U E... - Page 8 CD-ROM. Part no. HT3-2129-000-V.2.0 © 2003 Canon Inc. Canon, MultiPASS, and BCI are trademarks of Canon Inc. All other products and brand names are registered trademarks or trademarks of their respective owners. Specifications subject to change without notice.