Bushnell Night Vision 26-2042W User Manual

NIGHT VISION
I N S T R U C T I O N S
Lit. #: 06-2042W/3-01
Congratulations on the purchase of your Bushnell Night
Vision Product. Bushnell Night Vision products are comprised
of high quality image intensifier tubes and optics. Bushnell
Night Vision products amplify existing light, allowing you to
see in dark conditions too dark for the naked eye.
HOW NIGHT VISION WORKS
Bushnell Night Vision products collect and amplify existing light
through the objective lens, which is then focused on the image
intensifier. Inside the intensifier, a photocathode is "excited" by the
light and converts the photon energy into electrons. These electrons
accelerate across an electrostatic field inside the intensifier and strike
a phosphor screen (like a green monochrome TV screen) which emits
an image that you can see. It is the acceleration of electrons, which
provides gain and enhances the image. This is a Generation I device.
Special Features
This model was specifically designed for nighttime viewing near and
around water and marine life. It is ideal for boating, search and
rescue, fishing, and marine navigation. This product is waterproof
and floats in water.
GETTING STARTED
Installing Batteries
• Unscrew the Battery Compartment (a).
• Insert a CR2 3-volt lithium
battery into the compartment
+ first.
• Reseal the cover to
Battery Compartment.
Using the Power Button and
Infrared LED Illuminator
• Never turn the scope on in
daylight conditions with the
lens cap (b) off. The pinhole in the lens cap allows you to test the
scope in daylight conditions.
• To turn on the device, depress and hold the power button (c). A
green indicator light (d) will turn on when the power button is
depressed and held down.
26-2042W
c
e
b
the
a
g
• To turn on the IR (e) (Infrared Illuminator), depress and hold down
the IR button. A red indicator light (f) will turn on when the IR
button is depressed and held down. Your Bushnell Night Vision
product includes a built-in infrared illuminator. This allows you to
see in complete darkness when no ambient light source is available.
• After you release the Power Button, the image will slowly fade out.
This is normal and is not a defect.
To Focus
• First, turn the Objective Lens Focusing Ring (g) to infinity. (Full
clockwise as shown in the drawing).
• While looking at a distant object (at least 20-ft. away), adjust the
Eyepiece Focusing Ring (h) for the sharpest image.
• Once the Eyepiece Focusing Ring is adjusted, you need only adjust
the Objective Lens Focusing Ring as needed.
Spots In the Image
• You may see spots in the image. These vary from scope to scope and
are cosmetic blemishes inside the scope. These are normal for Night
Vision Scopes and are NOT a defect.
TROUBLESHOOTING
Scope will not turn on.
Check that the battery is installed properly. Replace the battery
with a new 3-volt Lithium battery. Check the battery contact to
ensure they are clean and free of corrosion. Check that the power is
being depressed.
Image is not focused.
Adjust the focus on the Focusing Eyepiece. Adjust the Objective Lens
Focusing Ring. For a focused image, you must be at least .5 feet away
from the object you are viewing. If still no improvement, clean the
lenses; they may be foggy or dusty. (See To Focus).
Visibility decreases or disappears.
Bright light sources such as headlights may cause visibility to degrade
or disappear completely. Release the Power Button and turn the
scope away from the light source. The unit will restore itself in 1 or 2
minutes. Conditions such as fog or extremely dark environments will
decrease visibility.
Scope flashes.
The scope may flash when used in a bright environment. It may also
flash during the first few seconds of use in dark environments.
CARE & MAINTENANCE
• When not using for an extended amount of time, remove the
battery and store the product in a dry location.
• Avoid turning the product on in extremely bright light conditions.
• Handle this product like you would a camera. Though Bushnell
Night Vision products are durably constructed, the image
intensifier tube consists of glass and is subject to breakage.
• Keep the optics clean. We recommend using a camera cleaner kit to
clean the outside of the objective and eyepiece lenses. Follow the
directions with the kit.
• Do not disassemble this product. Unauthorized disassembly not
d
only voids the warranty but may also cause damage from the lack
f
of special tools and techniques.
Specifications
Waterproof:
Floatable:
h
Magnification:
Objective Size:
Viewing Range (Ft.)
Field of View:
Infrared Illuminator:
Battery Type:
Size (Inches):
Weight (oz):
YES
YES
2.0 X
42 mm
.5 - 675
70 feet at 100 yards
Built-In
CR2 3-volt Lithium
7 x 2.3 x 3.1
15
Continued on page 2