Pentair Caddy MAC2 Series Instruction Sheet

INSTRUCTION SHEET
MAC2 Series
MC/AC Support Clips
For Cable Sizes
14-2 Through 10-3
With Ground
Part Number Figure
MAC2
MAC2T
MAC2ATA
MAC2BC
MAC224SM
MAC258SM
MAC2912SM
MAC2VF14
MAC2123
MAC2AO
MAC224
MAC258
MAC2912
MAC21318
MAC24Z34
MAC26Z34
MAC2FB
*Note: MAC2 snaps apart for single applications. Assemblies do not have this feature.
WARNING:
1. Pentair products shall be installed and used only as indicated in Pentair product instruction sheets and training materials. Instruction sheets are available at
www.erico.pentair.com and from your Pentair customer service representative.
2. PENTAIR products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
3. All instructions must be completely followed to ensure proper and safe installation and performance.
4. Improper installation, misuse, misapplication or other failure to completely follow Pantair's instructions and warnings may cause product malfunction, property
damage, serious bodily injury and/or death, and void your warranty.
5. Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
6. All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
other purpose.
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified
engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
Pentair, CADDY, ERICO CADWELD, ERICO CRITEC, ERICO, ERIFLEX, and LENTON are owned by Pentair or its global affiliates. All other trademarks
are the property of their respective owners. Pentair reserves the right to change specifications without prior notice.
TECHNICAL SUPPORT:
www.erico.pentair.com
Metal and wood stud, and flanges up to 1/16"
Double runs of MC/AC cable from structural members, wires, and rods
Figure 2
Figure 7
Description (in [mm])
1 Metal or wood stud and 1/16" [2] flange
2 Supports 1 to 4 runs of MC/AC cable for metal stud
3
4
5
6 1/16" [2] through 1/4" [6] C Purlin or vertical flange
7
8
1/8" [3] through 1/4" [6] flange - bottom mount, rotates 360
5/16" [8] through 1/2" [13] flange - bottom mount, rotates 360
9
9/16" [14] through 3/4" [19] flange - bottom mount, rotates 360
13/16" [21] through 1-1/8" [28] flange - bottom mount, rotates 360
#12 through 1/4" [6] wire, plain or threaded rod and 1/8" [3] through 3/8" [10] flange
10
3/8" [10] plain or threaded rod and 3/8" [10] through 9/16" [14] flange
11
CFS242_F
Figure 1
Figure 3 Figure 4
Figure 8 Figure 9
Attaches MC/AC to:
Acoustical tee
1/8" [3] through 1/2" [13] flange
1/8" [3] through 1/4" [6] flange
5/16" [8] through 1/2" [13] flange
1/2" [13] through 3/4" [19] flange
Z purlin
Offset bracket
Through metal stud
1 OF 4 © 1997-2017 Pentair All Rights Reserved
Figure 6
Figure 5
Figure 10 Figure 11