ADTRAN SHDSL V.35 LTU Specifications

FRONT PANEL LED INDICATORS
TOTAL ACCESS
PWR Off
3000 SHDSL
Green
Yellow
V.35 LTU
SHDSL Off
Green
Red
G.703 Off
Green
SHDSL
Nx64k Off
1182008L5
Green
RTS Off
Green
Off
RLSD
Green
TST Off
Green
Blinking Yellow Module is running a BERT with bit errors
N
x
Red
6
4
ALM Off
K
Yellow
Red
V.35 PORT PIN ASSIGNMENTS
V.35 Port
Circuit No.
102
RX
103
PWR 104
105
SHDSL
106
G.703
107
G.703
108/2
Nx64K
109
TX 113
RTS
114
115
RLSD
140
TST
141
142
ALM
INTERFACE CONNECTIONS
The G.703 signal is transmitted to the network either via the Total Access 3000 backplane connectors or
the two BNC connectors mounted on the faceplate. The G.703 signal and the SHDSL signal use the
following backplane amphenol connector Pairs:
SHDSL - Pair 2
G.703 Tx - Pair 8
G.703 Rx- Pair 7
C A U T I O N C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
TOTAL ACCESS
No power
Self-test passed and the module is In Service
Self-test passed and the module is Out of Service
SHDSL Loop is Out of Service -- Unassigned
SHDSL Loop is trained
SHDSL Loop is not trained
G.703 port is not configured, Out of Service -- Unassigned, or in alarm
condition
G.703 port configured and no alarms
Service is not configured or in alarm condition
Service is configured and operating normally
Nx64k service not configured or RTS control line is OFF
RTS control line is ON
Nx64k service not configured or RLSD control line is OFF
RLSD control line is ON
Module is not in loopback or BERT
Local loopback is active, or BERT running with no errors
BERT running with no pattern sync
No alarm condition detected
Remote alarm condition detected
Alarm condition detected locally
Circuit Name To/From DCE
Signal Ground
Transmit Data To
Receive Data From
Request To Send To
Clear To Send From
Data Set Ready From
Data Terminal Ready To
Received Line Signal Detect From
Transmit Signal Element Timing To
Transmit Signal Element Timing From
Receive Signal Element Timing From
Remote Loopback To
Local Loopback To
Test Indicator From
For a complete Installation and Maintenance faxback: (877) 457-5007, Document #766. Please have your fax number available.
®
3000 SHDSL V.35 LTU
DEFAULT PROVISIONING OPTIONS
Provisioning
Unit Options
Cross-Connect Map
Local Management
LT Mode Clk Source
NTU Auto Provisioning
External Port Alarms
Line Card Service State
G.703 Port Service State
Nx64K Port Service State
SHDSL Options
Rate (Kbps)
SNR Margin Alarm Threshold(dB)
Loop Attenuation Alarm Threshold (dB)
Test Options
Pinout (A/B)
Loopback Timeout(Min)
B
BERT Test Pattern
P/S
R/T
C
D
BERT Test Pattern Polarity
E
Nx64K In-band Pattern Detection
H
F COMPLIANCE
U/W
Caution: Up to -200 VDC may be present on telecommunications wiring.
Y/AA
This product is intended for installation in restricted access locations only and in
V/X
equipment with a Type "B" or "E" enclosure.
N
L
Code
NN
Power Code (PC)
Telecommunication Code (TC)
Installation Code (IC)
JOB
61182008L5-22A
Options Default
All Idle
Disabled, Enabled Enabled
Internal Clock Internal Clock
Nx64 ETC
G.703 RX Clock
Disabled, Enabled Disabled
Disabled, Enabled Enabled
In Service Out of Service - Unassigned
Out of Service - Maintenance
Out of Service - Unassigned
In Service Out of Service - Unassigned
Out of Service - Maintenance
Out of Service - Unassigned
In Service Out of Service - Unassigned
Out of Service - Maintenance
Out of Service - Unassigned
Enter a new value for N from 3 to 36, 2056 (N=32)
where Rate(Kbps)=(N x 64) + 8:
Disabled, Enabled Disabled
Disabled, Enabled Disabled
Disabled, Enabled Disabled
All Zeros 2e15-1
All Ones
2e15-1
2e23-1 2e15-1
Normal, Inverted Normal
Disabled, Enabled Disabled
Input Output
F C
– X
A –
A
ID
0202