Advertisement
Quick Links
CLEI: SOOTAK8J_ _
Product P/N: 1442180G2
D
ESCRIPTION
The Small Form‐Factor Pluggable (SFP) Gigabit Ethernet,
Single‐Fiber is a bidirectional SFP that plugs into an
Optical Line Terminal (OLT) designed to accept SFPs. The
SFP provides a single optical interface to the GigE physical
interface. Installed into an appropriate OLT, the SFP
provides a Gigabit Ethernet interface to the supporting
system.
NOTE
To ensure compatibility, refer to the documentation
provided with the OLT.
NOTICE
In a deployment consisting of an OLT with a 1442180G2
SFP installed; the Network Unit (ONT) should have a
complementary 1442180G1 SFP installed.
Rx: 1490 nm
OLT
Tx: 1550 nm
1442180G1
The following features are supported on the SFP:
♦
1000Base‐LX 1490 nm Transmitter
♦
1000Base‐LX 1550 nm Receiver
♦
Optical distance: 80 km maximum
!
CAUTION
Due to compliance certification requirements, only SFPs
supplied by ADTRAN should be used. ADTRAN cannot
certify system integrity with other SFPs.
Small Form-Factor Pluggable
1490nm TX 1550nm RX 80km
Rx: 1550 nm
ONU
Tx: 1490 nm
1442180G2
Operational Specifications
♦
Optical Specifications:
◊
Transmit wavelength: 1490 nm
◊
Receive wavelength: 1550 nm
◊
Optical transmit level: –2 dBm to +3 dBm
◊
Optical receive level: –25 dBm to –3 dBm
◊
Optical distance: 80 km
◊
Optical connectors: LC
♦
Extended Environmental Support:
◊
Operational temperature range: –40°C to +70°C
◊
Storage temperature range: –40°C to +85°C
◊
Relative humidity to 95%, noncondensing
I
NSTALLATION
Prior to installation, inspect the SFP. If damage has occured
during shipping, file a claim with the carrier, and then
contact ADTRAN Customer Support. For more infor‐
mation, refer to "Warranty".
To install the SFP into an appropriate module, complete the
following steps:
1. Insert the SFP into the SFP cage on the circuit board of
the host module with the latch handle facing outward.
Slide the SFP all the way into the cage.
NOTE
The latch on the SFP is for removal only. When removing
the SFP, rotate the latch away from the SFP, the SFP should
slide easily out of the cage.
2. Exert adequate pressure to ensure the SFP is
completely seated in the SFP cage.
3. Do not remove the connector plug until the optical
fiber connection is made.
NOTICE
It is recommended that the connector plug remain on
whenever the transciever optical fiber connector is not
inserted.
4. Continue the installation and turn‐up of the host
module using the instructions in the Job Aid provided
with the module, or using the Installation and
Maintenance Practice (I&M) available online at
www.adtran.com.
jobAid
Issue Date: November 2010
Document P/N: 61442180G2-22A
Advertisement
Summary of Contents for ADTRAN SOOTAK8J Series
- Page 1 Operational temperature range: –40°C to +70°C ◊ Storage temperature range: –40°C to +85°C The Small Form‐Factor Pluggable (SFP) Gigabit Ethernet, ◊ Single‐Fiber is a bidirectional SFP that plugs into an Relative humidity to 95%, noncondensing Optical Line Terminal (OLT) designed to accept SFPs. The SFP provides a single optical interface to the GigE physical interface. Installed into an appropriate OLT, the SFP NSTALLATION provides a Gigabit Ethernet interface to the supporting Prior to installation, inspect the SFP. If damage has occured system. during shipping, file a claim with the carrier, and then NOTE contact ADTRAN Customer Support. For more infor‐ To ensure compatibility, refer to the documentation mation, refer to “Warranty”. provided with the OLT. To install the SFP into an appropriate module, complete the following steps: NOTICE 1. Insert the SFP into the SFP cage on the circuit board of In a deployment consisting of an OLT with a 1442180G2 the host module with the latch handle facing outward. SFP installed; the Network Unit (ONT) should have a Slide the SFP all the way into the cage. complementary 1442180G1 SFP installed. NOTE Rx: 1490 nm Rx: 1550 nm Tx: 1550 nm Tx: 1490 nm The latch on the SFP is for removal only. When removing...
- Page 2 The ADTRAN system chassis frame ground terminal must be connected to an earth ground to ensure that the metal enclosure of the SFP is properly grounded via the backplane connector. Warranty: ADTRAN will replace or repair this product within the warranty period if it does not ADTRAN CUSTOMER CARE: meet its published specifications or fails while in service. Warranty information can From within the U.S. 1.800.726.8663 be found online at www.adtran.com/warranty.