Troy-Bilt 592 Operator's Manual

Troy-bilt edger operator's manual
Hide thumbs Also See for 592:

Advertisement

OPERATOR'S MANUAL
Edger
Model 592
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning:
This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine's exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
TROY-BILT LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
PRINTED IN U.S.A.
769-00044.fm
FORM NO.
(12/01)

Advertisement

Table of Contents
loading

Summary of Contents for Troy-Bilt 592

  • Page 1 OPERATOR’S MANUAL Edger Model 592 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest- covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
  • Page 2: Table Of Contents

    Content Important Safe Operation Practices ...3 Assembling The Edger ...5 Know The Edger...6 Operating The Edger ...7 Making Adjustments ...8 Maintaining and Servicing The Edger...10 Troubleshooting ...12 Parts List ...13 Warranty Information...Back Cover This Operator’s Manual is an important part of your new edger. It will help you assemble, prepare and maintain the unit for best performance.
  • Page 3: Important Safe Operation Practices

    SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.
  • Page 4: Maintenance And Storage

    4. Never operate with damaged safety devices. Failure to do so, can result in personal injury. 5. Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas. 6. Do not operate machine while under the influence of alcohol or drugs.
  • Page 5: Assembling The Edger

    SECTION 2: ASSEMBLING YOUR EDGER This unit is shipped WITHOUT IMPORTANT: GASOLINE or OIL. After setting up the unit, service engine with gasoline and oil as instructed in the Briggs & Stratton Owner/Operator Manual packed with your edger. NOTE: Reference to right or left hand side of the edger is observed from the operating position.
  • Page 6: Know The Edger

    Hairpin Clip Flat Washer Figure 5 Perform the clutch rod adjustment before IMPORTANT: operating the edger. Clutch Rod Adjustment Before operating the edger, check the adjustment of the clutch rod as follows: SECTION 3: KNOW THE EDGER Throttle Control The throttle control lever is located on the engine. It can be adjusted to regulate the engine speed only.
  • Page 7: Operating The Edger

    Throttle Control & Choke Control Curb Height Adjustment Lever Pull Rope / Recoil Starter SECTION 4: OPERATING THE EDGER The operation of any edger can result WEAR YOUR in foreign objects being thrown into SAFETY GLASSES the eyes, which can result in severe eye damage.
  • Page 8: Making Adjustments

    • Move the throttle control lever on the engine into the STOP or OFF position. Make certain that the engine’s spark plug IMPORTANT: wire is properly grounded as instructed in SECTION 2: Assembling The Edger before storing the edger for its next use.
  • Page 9 Edger Blade Angle Adjustment WARNING: Rotating cutting blade may throw objects causing personal injury. Keep area clear of bystanders and do not operate without guards in place. The cutting blade can be adjusted to eight positions. To adjust the blade angle, proceed as follows: •...
  • Page 10: Maintaining And Servicing The Edger

    Trimming Placing the blade angle adjustment lever in the notch furthest to the left will put the spindle assembly at a proper angle for trimming with the edger as illustrated in Figure 13. When the spindle assembly is rotated IMPORTANT: counter-clockwise (putting the blade closer to a horizontal position), it IS necessary to change the position of the front, left wheel to prevent the edger...
  • Page 11: Replacing The Edger Blade

    Figure 15 Replacing the Edger Blade • Use two wrenches (one wrench to prevent the hex bolt head from spinning and the other to remove the hex lock nut) to remove the edger blade. See Figure 16. Bell Washer Hex Bolt Head Figure 16 •...
  • Page 12: Troubleshooting

    Off-Season Storage Observe the following when preparing the edger for long-term storage: • Clean and lubricate unit thoroughly as instructed on page 10 of this manual. Refer to the Service, Storage & Specifications section of • the Briggs & Stratton Owner/Operator Manual packed with the edger for engine storage instructions.
  • Page 13: Parts List

    MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. Troy-Bilt LLC warrants this product against defects for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in materials or...

Table of Contents