Table of Contents
Advertisement
CONTENTS
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
XXL DISHWASHER
AUTOMATIC HIGH LOOP
AUTOMATIC HIGH LOOP
The drain hose is fastened to the back of
The drain hose is fastened to the back of
the machine at the best height. To elimina-
the machine at the best height. To elimina-
te potential drain problems, leave this hose
te potential drain problems, leave this hose
in place.
in place.
INSTALLATION
INSTRUCTIONS
2
2
3
3
4
5
7
8
9
9
10
12
12
12
13
14
Advertisement
Table of Contents
Related Manuals for Asko D5223XXLCS
Summary of Contents for Asko D5223XXLCS
-
Page 1: Table Of Contents
AUTOMATIC HIGH LOOP AUTOMATIC HIGH LOOP The drain hose is fastened to the back of The drain hose is fastened to the back of the machine at the best height. To elimina- the machine at the best height. To elimina- te potential drain problems, leave this hose te potential drain problems, leave this hose in place. -
Page 2: Introduction
NOTE: Cosmetic damage must be reported to the ASKO dealer within five days from the date of purchase. As soon as you unpack the dishwasher, thoroughly check it for cosmetic damage. -
Page 3: Dimensions
DIMENSIONS DD3232XLFI,D3251XLFI,D3531XLF D5112XXL, D5122XXL, D5152XXL, D5132XXL, D5223XXL, D5233XXL, D5253XXL, D5833XXL Height (Adjustable) Width (Including fill strips) Depth (Includes high loop) Depth W/Handle (HD) Depth W/Door Open Weight: 24" 610 mm PREPARING THE LOCATION The best place for your dishwasher is in the kitchen near the sink. -
Page 4: Dimensions
*If an accessory fill strip is used for FI models, 3/8” (9.5mm) must be added to the dishwasher height and cutout height **Does not include the depth of a custom or optional door. If an ASKO optional door is used, add 2-1/2” (63.5 mm) to the depth... -
Page 5: Custom Door Panel Dimensions
CUSTOM DOOR PANEL DIMENSIONS FITTING THE D5232XXLFI, D5233XXLFI, D5251XXFI, D5253XXLFI, D5531XXLFI, D5731XXLFI, D5833XXLFI ASKO-MADe Or cuStOM DOOr pAneL - 4 Inch tOe KIcK. The D5232XXLFI, D5233XXLFI, D5251XXFI, D5253XXLFI, D5531XXLFI, D5731XXLFI and D5833XXLFI can be installed with a fully integrated, buyer supplied custom door panel or ASKO accessory panel that extends from the toe kick to the counter top. -
Page 6: Xlfi Trim Kit Installation Options
XLFI TRIM KIT INSTALLATION OPTIONS ASKO XLFI dishwashers can be installed either with or without accessory fill strips depending on the type of installation. If the dishwasher cutout has been cut to European widths of 23-5/8”, the unit won’t require fill strips. If the dishwasher cutout is a standard 24”... -
Page 7: Water Supply
CORNER INSTALLATION If the dishwasher is installed in a corner, there must be a minimum clearance of 2” (50 mm) from the side wall so the door can open. 2” clearance WATER SUPPLY WARNING!! Plumbing connections must comply with applicable sanitary, safety and plumbing codes in your area. -
Page 8: Drain Connections
ASKO provides a 7/8” (22 mm) diameter corrugated drain hose which is connected to the back of the unit to form a high loop. If additional drain hose is needed, please purchase an ASKO drain hose extension kit with a 7/8” (22mm) copper tube. NOTE: Do not use any fittings anywhere in the drain line that are less than 7/8”... -
Page 9: Electrical Connections
ELECTRICAL CONNECTIONS WARNING! Before working on wiring for any electrical appliance, be sure the electrical power has been turned off at the breaker/fuse box. WARNING! Disconnect electrical power supply and place a tag at the disconnect switch indicating that you are working on the circuit. -
Page 10: Moving The Machine Into Place
MOVING THE MACHINE INTO PLACE WARNING! Make sure you put the protective slides on the legs to prevent damaging the floor when you slide the unit into place (see page 9). 1. Position the machine in front of the cabinet opening. 2. -
Page 11: Connecting The Water Supply
CONNECTING THE WATER SUPPLY In order to prevent heat damage to the inlet valve, all solder connections must be made before the water supply line is connected. Flush the water supply line prior to connecting it to the water fill tube. The unit has a float switch in the base pan to protect against flooding. -
Page 12: Adjusting The Leveling Legs
ADJUSTING THE LEVELING LEGS Now that all the connections are made and the machine is in place under the cabinet, you should make the final height adjustment. 1. You should set the rear foot first. To do this, use a screwdriver to rotate the adjusting screw on the bottom front of the machine. -
Page 13: Installation Checklist
INSTALLATION CHECKLIST ASKO - DIShwASher Appliance Installation Checklist • Remove packaging and check for cosmetic damages. • Remove the information packets from inside the dishwasher. • Attach any accessories as required by the installation. Fill strips, wooden door panels, accessory door panels... -
Page 14: Index
INdEx Cabinet, fastening unit to 12 Connecting to water supply 11 Cosmetic damage 2 Door springs, adjusting 9 Drain connections 8 Electrical cable connection 10 Electrical connections 9 Fastening unit to cabinet 12 Grounding instructions 9 High loop 8 Hot water supply 7 Leaks, testing for 11 Leveling legs, adjusting 12 Materials 2... - Page 15 NOTES Customer Care Center Page 15 1-800-898-1879 www.askousa.com...
- Page 16 Art. No 80 80 16 Rev. 01 Customer Care Center Page 16 1-800-898-1879 www.askousa.com...